Do SATA Tapes work on *any* SATA controller?
Executive Summary: Do SATA Tape drives work at all?
Ages past (March 28th) I posted to this list about my problems with Sony AIT tape drives on a nVidia MCP55 SATA controller (using sata_nv).
I never did get them working so I've just bought a Silicon Image PCI SiI 3512 SATA controller (using the sata_sil driver) to see if it might work.
Sadly it doesn't and I still can't write tapes on a SATA drive with Linux 2.6.25.1.
So before I put my SATA Tape drives in the bin, bite the bullet and purchase SCSI versions and SCSI controllers I thought I'd ask if the list knew of *any* SATA controller that works with tape drives in Linux?
Anyone? At all?
The Tape drives work with a (Sony supplied JMicron) USB to SATA adaptor so I'm quite sure it's a SATA driver/controller issue and not a Tape drive problem (I've now tried three drives just to make sure).
FWIW, dmesg for a failed tape write using sata_sil goes like:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata8.00: configured for UDMA/100
ata8: EH complete
st0: Sense Key : Aborted Command [current] [descriptor] Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0e 09 0c 00 00 00 03 00 00 00 00 00 00 a0 10
st0: Add. Sense: No additional sense information
st0: Sense Key : Unit Attention [current]
Info fld=0x1
st0: Add. Sense: Power on, reset, or bus device reset occurred
st0: Error on write filemark.
st0: Sense Key : Not Ready [current]
st0: Add. Sense: Logical unit not ready, cause not reportable
and my original post re the sata_nv problems was:
Quoted 190 lines
I'm trying to use a Sony AIT SDX-870V tape drive on an NVidia MCP55 SATA controller and it's basically not working :-(
I've tried two tape drives, different cables, different SATA ports and various kernels upto 2.6.25-rc7. All suffer from the same problem when reading/writing data. FWIW I do have a SATA CDRW drive on the same system and can read from that all day long without problems.
The drive status is readable (and doing this doesn't cause failures):
# mt -f /dev/st0 status SCSI 2 tape drive: File number=0, block number=-1, partition=0. Tape block size 1024 bytes. Density code 0xb3 (no translation). Soft error count since last status=0 General status bits on (1010000): ONLINE IM_REP_EN #If I write (using tar cvf
/dev/st0...) a small amount of data, then some it gets written (I can read back half a dozen files). Anything non-trivial however always results in:ata3.00: exception Emask
0x0SAct0x0SErr0x0action0x2ata3.00: BMDMA stat0x4
ata3.00: cmd a0/01:00:00:00:28/00:00:00:00:00/a0 tag 0 dma 10240 outcdb 0a 01 00 00 0a 00 00 00 00 00 00 00 00 00 00 00 res 10/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x2 (HSMviolation)
ata3: soft resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata3.00: configured for UDMA/100
ata3: EH complete
st0: Sense Key : Aborted Command [current] [descriptor] Descriptor sense data with sense descriptors (in hex):72 0b 00 00 00 00 00 0e 09 0c 00 00 00 03 00 00 00 00 00 00 a0 10st0: Add. Sense: No additional sense information
st0: Sense Key : Unit Attention [current]
Info fld=0x1
st0: Add. Sense: Power on, reset, or bus device reset occurred
st0: Error on write filemark.
st0: Sense Key : Not Ready [current]
st0: Add. Sense: Logical unit not ready, cause not reportableThe drive detection bit from kern.log goes:
Mar 28 09:56:34 build kernel: ata1: SATA link down (SStatus 0 SControl 300) Mar 28 09:56:34 build kernel: ata2: SATA link down (SStatus 0 SControl 300) Mar 28 09:56:34 build kernel: ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 22 Mar 28 09:56:34 build kernel: ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [LSA1] -> GSI 22 (level, low) -> IRQ 22 Mar 28 09:56:34 build kernel: PCI: Setting latency timer of device 0000:00:05.1 to 64 Mar 28 09:56:34 build kernel: scsi3 : sata_nv Mar 28 09:56:34 build kernel: scsi4 : sata_nv Mar 28 09:56:34 build kernel: ata3: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa080 irq 22 Mar 28 09:56:34 build kernel: ata4: SATA max UDMA/133 cmd 0xa480 ctl 0xa400 bmdma 0xa088 irq 22 Mar 28 09:56:34 build kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Mar 28 09:56:34 build kernel: ata3.00: ATAPI: SONY SDX-870V, 0100, max UDMA/100 Mar 28 09:56:34 build kernel: ata3.00: applying bridge limits Mar 28 09:56:34 build kernel: ata3.00: configured for UDMA/100 Mar 28 09:56:34 build kernel: ata4: SATA link down (SStatus 0 SControl 300) Mar 28 09:56:34 build kernel: scsi 3:0:0:0: Sequential-Access SONY SDX-870V 0100 PQ: 0 ANSI: 3 Mar 28 09:56:34 build kernel: st 3:0:0:0: Attached scsi tape st0 Mar 28 09:56:34 build kernel: st 3:0:0:0: st0: try direct i/o: yes (alignment 4 B) Mar 28 09:56:34 build kernel: st 3:0:0:0: Attached scsi generic sg6 type 1 Mar 28 09:56:34 build kernel: ACPI: PCI Interrupt Link [LSA2] enabled at IRQ 21 Mar 28 09:56:34 build kernel: ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [LSA2] -> GSI 21 (level, low) -> IRQ 21 Mar 28 09:56:34 build kernel: PCI: Setting latency timer of device 0000:00:05.2 to 64 Mar 28 09:56:34 build kernel: scsi5 : sata_nv Mar 28 09:56:34 build kernel: scsi6 : sata_nv Mar 28 09:56:34 build kernel: ata5: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 21 Mar 28 09:56:34 build kernel: ata6: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 21 Mar 28 09:56:34 build kernel: ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Mar 28 09:56:34 build kernel: ata5.00: ATAPI: ASUS DRW-2014L1T, 1.00, max UDMA/66 Mar 28 09:56:34 build kernel: ata5.00: configured for UDMA/66 Mar 28 09:56:34 build kernel: ata6: SATA link down (SStatus 0 SControl 300) Mar 28 09:56:34 build kernel: scsi 5:0:0:0: CD-ROM ASUS DRW-2014L1T 1.00 PQ: 0 ANSI: 5 Mar 28 09:56:34 build kernel: sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Mar 28 09:56:34 build kernel: Uniform CD-ROM driver Revision: 3.20 Mar 28 09:56:34 build kernel: sr 5:0:0:0: Attached scsi CD-ROM sr0 Mar 28 09:56:34 build kernel: sr 5:0:0:0: Attached scsi generic sg7 type 5 Mar 28 09:56:34 build kernel: ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 20lspci -v (for the SATA stuff) shows:
00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: Super Micro Computer Inc Unknown device a011 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at b480 [size=8] I/O ports at b400 [size=4] I/O ports at b080 [size=8] I/O ports at b000 [size=4] I/O ports at ac00 [size=16] Memory at dfaf9000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Capabilities: [cc] HyperTransport: MSI Mapping00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: Super Micro Computer Inc Unknown device a011 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 I/O ports at a880 [size=8] I/O ports at a800 [size=4] I/O ports at a480 [size=8] I/O ports at a400 [size=4] I/O ports at a080 [size=16] Memory at dfaf8000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Capabilities: [cc] HyperTransport: MSI Mapping00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: Super Micro Computer Inc Unknown device a011 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 I/O ports at a000 [size=8] I/O ports at 9c00 [size=4] I/O ports at 9880 [size=8] I/O ports at 9800 [size=4] I/O ports at 9480 [size=16] Memory at dfaf7000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Capabilities: [cc] HyperTransport: MSI MappingUsing the 'sonytools' utility, I can do things like eject the tape (mt does that too) but trying a 'longer' command like tape format results in:
# sonytape
/dev/st0-p
SONY tape device detected.
SONY SDX-870V Revision: 0100
Please Load Tape In Drive!
Sleeping 60 seconds.
Formatting Tape.
Request Sense data:0x720x0b0x470x000x000x000x000x0e0x090x0c0x000x000x000x000x000x000x000x020x000x000xa00x58
Unknown Sense Code, No additional sense information
Done.
#and dmesg for this failure says:
ata3.00: exception Emask
0x0SAct0x0SErr0x0action0x2frozen ata3.00: cmd a0/00:00:00:16:00/00:00:00:00:00/a0 tag 0 pio 24 outcdb 15 10 00 00 16 00 00 00 00 00 00 00 00 00 00 00 res 58/00:00:00:02:00/00:00:00:00:00/a0 Emask 0x6 (timeout)ata3.00: status: { DRDY DRQ }
ata3: port is slow to respond, please be patient (Status0xd0)
ata3: device not ready (errno=-16), forcing hardreset
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata3.00: configured for UDMA/100
ata3: EH complete
st0: Sense Key : Unit Attention [current]
st0: Add. Sense: Power on, reset, or bus device reset occurredAs I said earlier, small amounts of data work like so:
# tar cvf /dev/st0 . ./ ./sonytape ./nori_trace.txt ./SDX-870V.pdf ./sonytape_linux_v2.8.tar.gz ./sdx870v_0100.v87 ./datap.bin ./readme_sonytape_linux_v2.8.txt ./chnginq.txt # tar vtf /dev/st0 drwxrwxr-x root/root 0 2008-03-27 15:07 ./(quoted diff) +0
-4-rwxr-xr-x root/root 135282 2008-03-19 18:29 ./sonytape -rw-rw-r-- root/root 1360365 2008-03-27 15:07 ./nori_trace.txt -rw------- root/root 481793 2008-03-27 14:48 ./SDX-870V.pdf -rw-rw-r-- root/root 57566 2008-03-27 14:48./sonytape_linux_v2.8.tar.gz
(quoted diff) +0
-3-rw------- root/root 1514496 2008-03-27 14:48 ./sdx870v_0100.v87 -r-xr-xr-x root/root 65536 2003-07-20 16:43 ./datap.bin -rw-r--r-- root/root 12674 2008-03-19 15:28./readme_sonytape_linux_v2.8.txt
-r-xr-xr-x root/root 28 2008-03-19 18:15 ./chnginq.txt
#So it's seemingly something to do with the amount of data being sent to the drive.
Can anyone suggest a course of action to getting this fixed? I'm very happy to stick debug in bits of the kernel and report results.
Signature · 7 lines
Regards,
Russell
--------------------------------------------------------------------
| Russell Brown | MAIL: [email protected] PHONE: 01780 471800 |
| Lady Lodge Systems | WWW Work: http://www.lls.com |
| Peterborough, England | WWW Play: http://www.ruffle.me.uk |
--------------------------------------------------------------------Quoted 10 lines · Russell Brown
Executive Summary: Do SATA Tape drives work at all?
Ages past (March 28th) I posted to this list about my problems with Sony AIT tape drives on a nVidia MCP55 SATA controller (using
sata_nv).I never did get them working so I've just bought a Silicon Image PCI SiI 3512 SATA controller (using the
sata_sildriver) to see if it might work.
Quoted 8 lines
Sadly it doesn't and I still can't write tapes on a SATA drive with Linux 2.6.25.1.
So before I put my SATA Tape drives in the bin, bite the bullet and purchase SCSI versions and SCSI controllers I thought I'd ask if the list knew of *any* SATA controller that works with tape drives in Linux?
Anyone? At all?
Albert Lee worked on tape drive support a while ago and ISTR he got a few devices working. I'm interested. Are you willing to ship the drive to me? I can pay via paypal unless it's too expensive.
Thanks.
Signature · 1 line
tejun