Misidentification and failing revalidations of ide dvd-roms with libata
Hi all,
I have a curious issue on an NForce4, x86_64 system. After reinstalling it with a new distro (Ubuntu 8.04-based MythBuntu 8 - 2.6.24-19-generic, i686), I am experiencing failing revalidations of my IDE DVD-rom drives;
[ 152.874745] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[ 152.874753] ata4.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 pio 8 in
[ 152.874754] cdb 4a 01 00 00 10 00 00 00 08 00 00 00 00 00 00 00
[ 152.874755] res 68/00:01:00:08:00/00:00:00:00:00/a0 Emask 0x2 (HSM violation)
[ 152.874758] ata4.00: status: { DRDY DF DRQ }
[ 152.874775] ata4: soft resetting link
[ 153.124616] ata4.00: model number mismatch 'Pioneer DVD-ROM ATAPIModel DVD-116 0109' != 'Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹'
[ 153.124621] ata4.00: revalidation failed (errno=-19)
[ 153.124624] ata4: failed to recover some devices, retrying in 5 secs
[ 155.206856] ata4: soft resetting link
[ 155.457098] ata4.00: model number mismatch 'Pioneer DVD-ROM ATAPIModel DVD-116 0109' != 'Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹'
[ 155.457103] ata4.00: revalidation failed (errno=-19)
[ 155.457106] ata4.00: disabled
[ 155.666359] ata4: soft resetting link
[ 155.916202] ata4.00: ATAPI: Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹, E1.±9 ¡, max UDMA7
[ 155.919834] ata4.00: failed to set xfermode (err_mask=0x1)
[ 155.919837] ata4: failed to recover some devices, retrying in 5 secs
[ 158.002170] ata4: soft resetting link
[ 158.255648] ata4.00: failed to set xfermode (err_mask=0x1)
[ 158.255653] ata4.00: limiting speed to UDMA/100:PIO3
[ 158.255655] ata4: failed to recover some devices, retrying in 5 secs
[ 160.338395] ata4: soft resetting link
[ 160.591046] ata4.00: failed to set xfermode (err_mask=0x1)
[ 160.591050] ata4.00: disabled
[ 160.800818] sr 3:0:0:0: rejecting I/O to offline device
[ 160.800827] ata4: EH complete
[ 160.801023] ata4.00: detaching (SCSI 3:0:0:0)
[ 160.801192] scsi 3:0:0:0: rejecting I/O to dead device
[ 160.801205] scsi 3:0:0:0: rejecting I/O to dead device
[ 160.801208] scsi 3:0:0:0: rejecting I/O to dead deviceAs I understand, this would most commonly indicate that the drive has gone bad, but this also occurs on the /other/ drive (same make/model) in the system. Also, it occurs on one of them, and then so far not on the other (until I reboot the system). This has only occurred while the drives have been in use (ripping audio-CDs), and seems to occur fairly quickly when a drive is in use (during the first few CDs). If only one drive is in use, it will still fail.
This behaviour was never seen on the previous distro, CentOS4, 2.6.9-something). On this system, the drives were accessed as /dev/hda and /dev/hdc
Also, I notice that the kernel inconsistently identifies the capabilites of the drives;
[ 24.048722] Driver 'sr' needs updating - please use bus_type methods [ 24.053214] sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray [ 24.053220] Uniform CD-ROM driver Revision: 3.20 [ 24.053268] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 24.081327] sr1: scsi3-mmc drive: 12x/40x cd/rw xa/form2 cdda tray [ 24.081379] sr 3:0:0:0: Attached scsi CD-ROM sr1
Here, the speed-ratings are inconsistent. Both drives are same make/model, and the speed-rating is either seen as 40x/40x, 12x/40x or 125x/40x. These vary, seemingly at random, between boots. I believe I've never seen one of them /not/ be 40x/40x. It is possible that the one that is not 40x/40x is the one that fails, but I'm in no way certain about this.
I'm not sure what to make of this, as this is my first system that uses libata for ATAPI-devices like these.
The drives themselves are identified correctly.
[ 18.452227] ata3.00: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-116 0109, E1.09, max UDMA/66 [ 18.623964] ata3.00: configured for UDMA/66 [ 19.221877] ata4.00: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-116 0109, E1.09, max UDMA/66 [ 19.393614] ata4.00: configured for UDMA/66 [ 19.395336] scsi 2:0:0:0: CD-ROM PIONEER DVD-ROM DVD-116 1.09 PQ: 0 ANSI: 5 [ 19.395413] scsi 2:0:0:0: Attached scsi generic sg2 type 5 [ 19.396657] scsi 3:0:0:0: CD-ROM PIONEER DVD-ROM DVD-116 1.09 PQ: 0 ANSI: 5 [ 19.396702] scsi 3:0:0:0: Attached scsi generic sg3 type 5
Yours,
-S
Signature · 2 lines
Simen Thoresen, Dolphin ICS Systems Administration and Wulfkit Support
Quoted 3 lines
[ 155.457098] ata4.00: model number mismatch 'Pioneer DVD-ROM ATAPIModel DVD-116 0109' != 'Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹' [ 155.457103] ata4.00: revalidation failed (errno=-19)
So it failed because the data read from the drive was corrupted.
Quoted 2 lines
As I understand, this would most commonly indicate that the drive has gone bad, but this also occurs on the /other/ drive (same make/model) in
Or a cable problem.
Quoted 8 lines · Alan Cox
Quoted 2 lines
[ 155.457098] ata4.00: model number mismatch 'Pioneer DVD-ROM ATAPIModel DVD-116 0109' != 'Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹' [ 155.457103] ata4.00: revalidation failed (errno=-19)So it failed because the data read from the drive was corrupted.
Quoted 1 line
As I understand, this would most commonly indicate that the drive has gone bad, but this also occurs on the /other/ drive (same make/model) in
Or a cable problem.
Hi Alan,
Should this apply here too? There are two separate cables, and I've never seen the other drive to fail after the first drive has failed. I've now ripped ~50 CDs with the still working drive, while this drive failed during the first 5 CDs on my two previous boots.
I don't doubt that the revalidation goes bad, but I can't see hardware being the cause of it as it hits any drive, but so-far only one drive pr boot.
-S
Quoted 6 lines
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Signature · 2 lines
Simen Thoresen, Dolphin ICS Systems Administration and Wulfkit Support
Quoted 14 lines · On Sunday 20 July 2008 20:34:48 Simen Timian Thoresen wrote:
Quoted 10 lines · Alan Cox
Quoted 3 lines
[ 155.457098] ata4.00: model number mismatch 'Pioneer DVD-ROM ATAPIModel DVD-116 0109' != 'Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹' [ 155.457103] ata4.00: revalidation failed (errno=-19)So it failed because the data read from the drive was corrupted.
Quoted 2 lines
As I understand, this would most commonly indicate that the drive has gone bad, but this also occurs on the /other/ drive (same make/model) in
Or a cable problem.
Hi Alan,
Quoted 8 lines
Should this apply here too? There are two separate cables, and I've never seen the other drive to fail after the first drive has failed. I've now ripped ~50 CDs with the still working drive, while this drive failed during the first 5 CDs on my two previous boots.
I don't doubt that the revalidation goes bad, but I can't see hardware being the cause of it as it hits any drive, but so-far only one drive pr boot.
Power supply maybe? Check the rails. The +12VDC must be good.
Signature · 2 lines
Cheers, Alistair.
Quoted 10 lines · Alistair John Strachan
Quoted 6 lines · On Sunday 20 July 2008 20:34:48 Simen Timian Thoresen wrote:
Quoted 5 lines · Alan Cox
Quoted 3 lines
[ 155.457098] ata4.00: model number mismatch 'Pioneer DVD-ROM ATAPIModel DVD-116 0109' != 'Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹' [ 155.457103] ata4.00: revalidation failed (errno=-19)So it failed because the data read from the drive was corrupted.
Power supply maybe? Check the rails. The +12VDC must be good.
Hi Alistair,
Good suggestion - I've rebooted and am running the box with one of the DVDroms connected to an external PSU. I'd now expect the one on the internal rail to be the failing one, if either fails.
I'm done ripping CDs for now, but I'm checking to see if I can trigger the same ripping DVDs.
Yours,
-S
Signature · 2 lines
Simen Thoresen, Dolphin ICS Systems Administration and Wulfkit Support
Quoted 17 lines · Alistair John Strachan
Quoted 16 lines · On Sunday 20 July 2008 20:34:48 Simen Timian Thoresen wrote:
Quoted 8 lines · Alan Cox
Quoted 3 lines
[ 155.457098] ata4.00: model number mismatch 'Pioneer DVD-ROM ATAPIModel DVD-116 0109' != 'Pioïeer¡DVDROM¡ATAñIMoåel åVD-±16 ¡010¹' [ 155.457103] ata4.00: revalidation failed (errno=-19)So it failed because the data read from the drive was corrupted.
Quoted 2 lines
As I understand, this would most commonly indicate that the drive has gone bad, but this also occurs on the /other/ drive (same make/model) in
Or a cable problem.
Hi Alan,
Should this apply here too? There are two separate cables, and I've never seen the other drive to fail after the first drive has failed. I've now ripped ~50 CDs with the still working drive, while this drive failed during the first 5 CDs on my two previous boots.
Quoted 5 lines
Quoted 3 lines
I don't doubt that the revalidation goes bad, but I can't see hardware being the cause of it as it hits any drive, but so-far only one drive pr boot.
Power supply maybe? Check the rails. The +12VDC must be good.
Hi Alistair, Alan,
I've spent a few hours more looking into this, and I'm not really getting much clearer;
I've run either and both of the two DVDroms on an external power-supply (drive-power from a jumped, believed good ATX-PSU), and the the symptoms remain; inconsistent capabilities reported at boot, and when I start ripping CDs, one of them will fail as above.
As I still have the impression that this started when I switched distros (ie went from CentOS4 2.6.9 pre-libata-kernel to the current Ubuntu 8.04 2.6.24-kernel), I've now started playing around with the libata module parameters.
Further suggestions are most welcome .-)
Yours,
-S
Signature · 2 lines
Simen Thoresen, Dolphin ICS Systems Administration and Wulfkit Support
On Sunday 27 July 2008 20:33:21 Simen Timian Thoresen wrote:
[snip]
Quoted 8 lines
I've spent a few hours more looking into this, and I'm not really getting much clearer;
I've run either and both of the two DVDroms on an external power-supply (drive-power from a jumped, believed good ATX-PSU), and the the symptoms remain; inconsistent capabilities reported at boot, and when I start ripping CDs, one of them will fail as above.
Quoted 4 lines
As I still have the impression that this started when I switched distros (ie went from CentOS4 2.6.9 pre-libata-kernel to the current Ubuntu 8.04 2.6.24-kernel), I've now started playing around with the libata module parameters.
If it's not power then I'm still with Alan re the cables. Maybe you have very long cables?
I used Alan's nForce4 pata driver for a year or so and didn't have any problems. OTOH maybe at this stage it's worth checking whether amd74xx (old IDE) breaks in similar ways?
Also, I assume you've memtest86'ed the machine?
Signature · 2 lines
Cheers, Alistair.
Quoted 14 lines · Alistair John Strachan
On Sunday 27 July 2008 20:33:21 Simen Timian Thoresen wrote:
[snip]Quoted 12 lines
I've spent a few hours more looking into this, and I'm not really getting much clearer;
I've run either and both of the two DVDroms on an external power-supply (drive-power from a jumped, believed good ATX-PSU), and the the symptoms remain; inconsistent capabilities reported at boot, and when I start ripping CDs, one of them will fail as above.
As I still have the impression that this started when I switched distros (ie went from CentOS4 2.6.9 pre-libata-kernel to the current Ubuntu 8.04 2.6.24-kernel), I've now started playing around with the libata module parameters.
Hi Alistair,
I'm sorry I have not yet come back on this. I /think/ I've had success disabling DMA for atapi-devices (adding "options libata dma=5" to my modprobe.conf file). I've been able to rip a number of cds without any issues with this (except a reduced speed, I believe). I do get some noise in dmesg;
[ 9686.570804] end_request: I/O error, dev sr1, sector 0 [ 9686.570814] Buffer I/O error on device sr1, logical block 0 [ 9686.570819] Buffer I/O error on device sr1, logical block 1 [ 9686.572134] end_request: I/O error, dev sr1, sector 1024 [ 9686.573105] end_request: I/O error, dev sr1, sector 1024 [ 9686.574101] end_request: I/O error, dev sr1, sector 1024
...but cdparianoia (ripper application) never complains and I've not been able to notice any defects in the extracted audio.
As this was disabling DMA, and I've seen that frequency adjustments on the CPU can cause DMA issues (at the time, with the ivtv-driver) on this motherboard, I thought that I'd try disabling Cool'n'Quiet and thereby lock the CPU to full speed, while reenabling DMA, but that did not help. Ripping the first CDs, one of the drives failed again.
Quoted 1 line
If it's not power then I'm still with Alan re the cables. Maybe you have very long cables?
Nope, normal 40cm'is 80-pin IDE cables. While one could be bad, I wouldn't expect both to be (etc).
Quoted 1 line
I used Alan's nForce4 pata driver for a year or so and didn't have any problems. OTOH maybe at this stage it's worth checking whether amd74xx (old IDE) breaks in similar ways?
from dmesg, I have this;
[ 17.647757] pata_amd 0000:00:06.0: version 0.3.10 [ 17.650097] scsi0 : pata_amd [ 17.650229] scsi1 : pata_amd
(that's the one, right?)
...so the driver exists in the running kernel. Would I have to build my own kernel, or is there some way to have this driver take hold instead of libata? ...or can I do something in modprobe.conf to use the other driver?
Quoted 1 line
Also, I assume you've memtest86'ed the machine?
Not strictly recently. I'll leave it doing so this evening, as I'll want to reboot it to reactivate Cool'n'quiet.
Again, thank you for helping me look into this. For now it /looks/ like I could be happy doing PIO, but I'd prefer to have this solved properly if possible.
-S
Signature · 2 lines
Simen Thoresen, Dolphin ICS Systems Administration and Wulfkit Support
Quoted 10 lines · On Wednesday 30 July 2008 18:31:15 Simen Timian Thoresen wrote:
Quoted 3 lines · Alistair John Strachan
I used Alan's nForce4 pata driver for a year or so and didn't have any problems. OTOH maybe at this stage it's worth checking whether amd74xx (old IDE) breaks in similar ways?
from dmesg, I have this;
[ 17.647757] pata_amd 0000:00:06.0: version 0.3.10 [ 17.650097] scsi0 : pata_amd [ 17.650229] scsi1 : pata_amd
Quoted 6 lines
(that's the one, right?)
...so the driver exists in the running kernel. Would I have to build my own kernel, or is there some way to have this driver take hold instead of libata? ...or can I do something in modprobe.conf to use the other driver?
I have no clue what your distributor has enabled or disabled. The easiest way would be to ignore your distribution kernel and just build your own one.
You'll probably need to disable pata_amd (from "Serial ATA (prod) and Parallel ATA (experimental) drivers") and enable amd74xx (from "ATA/ATAPI/MFM/RLL support -> Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support -> AMD and nVidia IDE support (NEW)"). Note that you'll also need ide-cd for this subsystem.
As for DMA, I know there were issues with ATAPI on nForce 4 chipsets, but I don't really know the specifics. Could you try sata_nv.adma=0 on the kernel cmdline? This is probably a red herring though, as I'm not sure what relation the sata_nv driver has to pata_amd.
Signature · 2 lines
Cheers, Alistair.
Quoted 2 lines
cmdline? This is probably a red herring though, as I'm not sure what relation the
sata_nvdriver has topata_amd.
None whatsoever. pata_amd drives the PATA port, sata_nv is a driver for the older Nvidia SATA ports.
Quoted 43 lines · Simen Timian Thoresen
Quoted 14 lines · Alistair John Strachan
On Sunday 27 July 2008 20:33:21 Simen Timian Thoresen wrote:
[snip]Quoted 12 lines
I've spent a few hours more looking into this, and I'm not really getting much clearer;
I've run either and both of the two DVDroms on an external power-supply (drive-power from a jumped, believed good ATX-PSU), and the the symptoms remain; inconsistent capabilities reported at boot, and when I start ripping CDs, one of them will fail as above.
As I still have the impression that this started when I switched distros (ie went from CentOS4 2.6.9 pre-libata-kernel to the current Ubuntu 8.04 2.6.24-kernel), I've now started playing around with the libata module parameters.
Hi Alistair,
I'm sorry I have not yet come back on this. I /think/ I've had success disabling DMA for atapi-devices (adding "options libata dma=5" to my modprobe.conf file). I've been able to rip a number of cds without any issues with this (except a reduced speed, I believe). I do get some noise in dmesg;
[ 9686.570804] end_request: I/O error, dev sr1, sector 0 [ 9686.570814] Buffer I/O error on device sr1, logical block 0 [ 9686.570819] Buffer I/O error on device sr1, logical block 1 [ 9686.572134] end_request: I/O error, dev sr1, sector 1024 [ 9686.573105] end_request: I/O error, dev sr1, sector 1024 [ 9686.574101] end_request: I/O error, dev sr1, sector 1024...but cdparianoia (ripper application) never complains and I've not been able to notice any defects in the extracted audio.
As this was disabling DMA, and I've seen that frequency adjustments on the CPU can cause DMA issues (at the time, with the ivtv-driver) on this motherboard, I thought that I'd try disabling Cool'n'Quiet and thereby lock the CPU to full speed, while reenabling DMA, but that did not help. Ripping the first CDs, one of the drives failed again.
Quoted 1 line
If it's not power then I'm still with Alan re the cables. Maybe you have very long cables?
Nope, normal 40cm'is 80-pin IDE cables. While one could be bad, I wouldn't expect both to be (etc).
Quoted 1 line
I used Alan's nForce4 pata driver for a year or so and didn't have any problems. OTOH maybe at this stage it's worth checking whether amd74xx (old IDE) breaks in similar ways?
from dmesg, I have this;
[ 17.647757] pata_amd 0000:00:06.0: version 0.3.10 [ 17.650097] scsi0 : pata_amd [ 17.650229] scsi1 : pata_amd
Quoted 7 lines
(that's the one, right?)
...so the driver exists in the running kernel. Would I have to build my own kernel, or is there some way to have this driver take hold instead of libata? ...or can I do something in modprobe.conf to use the other driver?
Quoted 1 line
Also, I assume you've memtest86'ed the machine?
Not strictly recently. I'll leave it doing so this evening, as I'll want to reboot it to reactivate Cool'n'quiet.
It passed 22 runs over the night.
I'll aim to build a new kernel using the amd74xx pata driver over the weekend. For now, I can work with the system as it is using PIO for the DVDrom drives.
Yours,
-S
Quoted 4 lines
Again, thank you for helping me look into this. For now it /looks/ like I could be happy doing PIO, but I'd prefer to have this solved properly if possible.
-S
Signature · 2 lines
Simen Thoresen, Dolphin ICS Systems Administration and Wulfkit Support