Device tree question

I have added a compact flash to the external bus of a Sequoia (PPC440EPx) evaluation board. It is wired to CS1, and U-boot is set to configure CS1 to be at address 0xc1000000. U-boot can access the device, and reports the correct partition table, etc. so I believe the hardware is ok.

I've created a device-tree entry under the EBC0 section of the sequoia.dts file:

                pata@1,0 {
                    compatible = "harris,hydra_temp-pata", "ata-generic";
                    bank-width = <2>;
                    reg = <1 0 20 1 80 20>;
                    reg-shift = <4>;
                    pio-mode = <4>;
                    interrupts = <27 4>;
                    interrupt-parent = <&UIC0>;
                };
            };

This seems to be correct, because if I turn on debug in prom_parse, I see a translation that looks reasonable:

OF: translating address: 00000001 00000000
OF: parent bus is default (na=1, ns=1) on /plb/opb
OF: walking ranges...
OF: default map, cp=0, s=4000000, da=100000000
OF: default map, cp=100000000, s=100000, da=100000000
OF: parent translation for: c1000000
OF: with offset: 0
OF: one level translation: c1000000
OF: parent bus is default (na=2, ns=1) on /plb
OF: walking ranges...
OF: default map, cp=0, s=80000000, da=c1000000
OF: default map, cp=80000000, s=80000000, da=c1000000
OF: parent translation for: 00000001 80000000
OF: with offset: 41000000
OF: one level translation: 00000001 c1000000
OF: parent bus is default (na=2, ns=1) on /
OF: no ranges, 1:1 translation
OF: parent translation for: 00000000 00000000
OF: with offset: 1c1000000
OF: one level translation: 00000001 c1000000
OF: reached root node
OF: ** translation for device /plb/opb/ebc/pata@1,0 **
OF: bus is default (na=2, ns=1) on /plb/opb/ebc

(There is another translation for the alternate registers but I'll omit it for brevity.)

However, there is something wrong, because I get an oops:

Machine check in kernel mode.
Data Write PLB Error

Oops: Machine check, sig: 7 [#1]
LTT NESTING LEVEL : 0
Hydra_temp
Modules linked in:
NIP: c01e4618 LR: c01e4608 CTR: c01e4078
REGS: c0398f50 TRAP: 0214   Not tainted  (2.6.25.4-00021-g4b3b5ea-dirty)
MSR: 00029000 <EE,ME>  CR: 24044028  XER: 20000007

TASK = cf808400[1] 'swapper' THREAD: cf826000
GPR00: 00000008 cf827ce0 cf808400 cf3ac000 d1078080 00000000 00000001 c03869c0
GPR08: 00000000 c01e4078 cf3ac000 00000001 24044022 00000000 c02e977c c02e97e0
GPR16: c02e97c8 c036a8bc c02e97f4 c02e9808 c037c0a8 c0386978 00000000 cf360190
GPR24: 00000027 c0386a64 00000000 00000000 cf360190 00000000 cf360194 cf3ac000
NIP [c01e4618] ata_bmdma_freeze+0x44/0x70
LR [c01e4608] ata_bmdma_freeze+0x34/0x70

Call Trace:

[cf827ce0] [0000001f] 0x1f (unreliable) [cf827cf0] [c01e4c14] __ata_port_freeze+0x3c/0x5c [cf827d00] [c01e4fa4] ata_eh_freeze_port+0x40/0x5c [cf827d20] [c01d6868] ata_host_start+0xd8/0x208 [cf827d40] [c01dd2f4] ata_host_activate+0x28/0x124 [cf827d70] [c02a60c4] 0xc02a60c4
[cf827db0] [c02a642c] 0xc02a642c
[cf827e50] [c0222a7c] of_platform_device_probe+0x5c/0x560 [cf827e70] [c01b3148] driver_probe_device+0xb8/0x1e8 [cf827e90] [c01b3470] __driver_attach+0xcc/0xf8 [cf827eb0] [c01b21c4] bus_for_each_dev+0x5c/0x98 [cf827ee0] [c01b2f50] driver_attach+0x24/0x34 [cf827ef0] [c01b2da8] bus_add_driver+0x1d8/0x258 [cf827f20] [c01b371c] driver_register+0x48/0x114 [cf827f40] [c0222950] of_register_driver+0x54/0x70 [cf827f50] [c035ed08] pata_of_platform_init+0x20/0x30 [cf827f60] [c03471cc] kernel_init+0xc8/0x2ac [cf827ff0] [c000e44c] original_kernel_thread+0x44/0x60

My question is: Did I do the device-tree entry incorrectly or is something else wrong? I'll keep trying to figure it out on my own, but if anyone has any tips on debugging this, I'd love to hear them.

Steve
_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-dev

Quoted 20 lines · Steven A. Falco

I have added a compact flash to the external bus of a Sequoia (PPC440EPx) evaluation board. It is wired to CS1, and U-boot is set to configure CS1 to be at address 0xc1000000. U-boot can access the device, and reports the correct partition table, etc. so I believe the hardware is ok.

I've created a device-tree entry under the EBC0 section of the sequoia.dts file:

                pata@1,0 {
                    compatible = "harris,hydra_temp-pata", "ata-generic";
                    bank-width = <2>;
                    reg = <1 0 20 1 80 20>;
                    reg-shift = <4>;
                    pio-mode = <4>;
                    interrupts = <27 4>;
                    interrupt-parent = <&UIC0>;
                };
            };

Quoted 3 lines

This seems to be correct, because if I turn on debug in prom_parse, I see a translation that looks reasonable:

Did you check that the resulting physical address was indeed where you device is supposed to be addressed ?

Ben