LAN Timeout
Hello,
I have a problem concnering the LAN Connection Timeout.
I uses a Teridian Phy connected via MII Interface to an AT91SAM9260. All works fine. If I boot my system uboot comes up and detects the connection very quickly, so that my system boots fast. But if I have no lan cable plugged in when I boot my system, it takes some seconds to detect that no lan cable is plugged in and a timeout occurs.
How could I speed up my booting sequence if there is no lan cable plugged in ?
Thank you very much
Best regards
Manuel Sahm
Hello,
isn?t anybody out there who could help me ?
Thank you
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Manuel Sahm" <[email protected]> 26.08.2008 10:44 >>>
Hello,
I have a problem concnering the LAN Connection Timeout.
I uses a Teridian Phy connected via MII Interface to an AT91SAM9260. All works fine. If I boot my system uboot comes up and detects the connection very quickly, so that my system boots fast.
But if I have no lan cable plugged in when I boot my system, it takes some seconds to detect that no lan cable is plugged in and a timeout occurs.
How could I speed up my booting sequence if there is no lan cable plugged in ?
Thank you very much
Best regards
Manuel Sahm
Manuel,
we do this with conditional boot depending on environment settings, e.g. "netboot" yes or no.
If netboot==no then omit bootp/dhcp completely and proceed to boot from flash.
Otherwise try netboot and stick to the timeout. Autoneg can indeed take some time ...
This can easily be done with a bootscript, i.e. bootcmd=autoscr valid_addr.
regards,
Andre
Quoted 34 lines · Manuel Sahm
Hello,
isn??t anybody out there who could help me ?
Thank you
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
"Manuel Sahm" <[email protected]> 26.08.2008 10:44 >>>
Hello,
I have a problem concnering the LAN Connection Timeout.
I uses a Teridian Phy connected via MII Interface to an AT91SAM9260. All works fine. If I boot my system uboot comes up and detects the connection very quickly, so that my system boots fast.
But if I have no lan cable plugged in when I boot my system, it takes some seconds to detect that no lan cable is plugged in and a timeout occurs.How could I speed up my booting sequence if there is no lan cable plugged in ?
Thank you very much
Best regards
Manuel Sahm
Quoted 7 lines
------------------------------------------------------------------------
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler - Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner
Hello,
does anybody have an idea to fix this problem ?
Which paramter is for the "lan connection timeout" ?
Please, please help me
Thanks a lot
Manuel Sahm
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Manuel Sahm" <[email protected]> 26.08.2008 10:44 >>>
Hello,
I have a problem concnering the LAN Connection Timeout.
I uses a Teridian Phy connected via MII Interface to an AT91SAM9260. All works fine. If I boot my system uboot comes up and detects the connection very quickly, so that my system boots fast. But if I have no lan cable plugged in when I boot my system, it takes some seconds to detect that no lan cable is plugged in and a timeout occurs.
How could I speed up my booting sequence if there is no lan cable plugged in ?
Thank you very much
Best regards
Manuel Sahm
Hello,
Quoted 3 lines · Manuel Sahm
does anybody have an idea to fix this problem ?
Which paramter is for the "lan connection timeout" ?
Try to decrease CFG_MACB_AUTONEG_TIMEOUT in drivers/net/macb.c to 500000 or so. It is currently 5000000 which results in 5 sec. timeout in macb_phy_init() and also in macb_phy_reset().
Best regards,
Anatolij
Signature · 3 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
Quoted 6 lines · Anatolij Gustschin
Hello,
Quoted 2 lines · Manuel Sahm
does anybody have an idea to fix this problem ?
Quoted 8 lines
Quoted 1 line
Which paramter is for the "lan connection timeout" ?
Try to decrease
CFG_MACB_AUTONEG_TIMEOUTindrivers/net/macb.cto 500000 or so. It is currently 5000000 which results in 5 sec. timeout inmacb_phy_init()and also inmacb_phy_reset().Best regards,
Anatolij
Caution: don't reduce it to less than 2 seconds. The minimum PHY autonegotiation time is 2 seconds per definition by the standard: if you read the standard and add all the delays together, the sum is 2 seconds.
I've never seen a PHY take noticeably longer than 2 seconds for autonegotiation, but there is a world of PHYs out there that I've never tried.
Best regards,
gvb