Skip to contentSkip to conversation

libertas: Improvements on automatic tx power control via SIOCSIWTXPOW.

PATCH In review Anna Neal 3 participants 5 messages Sep 25, 2008 – Sep 29, 2008 Networking drivers (wireless)

lore
Share & tools
lore

Anna Neal

author
#0 lore raw

PATCH 1/1 libertas: Improvements on automatic tx power control via SIOCSIWTXPOW.

iwconfig txpower can now be used to set tx power to fixed or auto. If set to auto the default firmware settings are used.

The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams noted the command was no longer supported in firmware V9+.

---
 drivers/net/wireless/libertas/cmd.c     |   64 +++++++++++++++++++++++++++++++
 drivers/net/wireless/libertas/cmd.h     |    6 +++
 drivers/net/wireless/libertas/defs.h    |    9 ++++
 drivers/net/wireless/libertas/host.h    |    1 +
 drivers/net/wireless/libertas/hostcmd.h |   24 +++++++++--
 drivers/net/wireless/libertas/wext.c    |   32 ++++++++++++++-
 6 files changed, 129 insertions(+), 7 deletions(-)
drivers/net/wireless/libertas/cmd.c +64 -0
index 7e818b0..a912fb6 100644
@@ -1927,6 +1927,70 @@ void lbs_ps_confirm_sleep(struct lbs_private *priv)
 }
 
 
+/**
+ * @brief Configures the transmission power control functionality.
+ *
+ * @param priv		A pointer to struct lbs_private structure
+ * @param enable	Transmission power control enable
+ * @param p0		Power level when link quality is good (dBm).
+ * @param p1		Power level when link quality is fair (dBm).
+ * @param p2		Power level when link quality is poor (dBm).
+ * @param usesnr	Use Signal to Noise Ratio in TPC
+ *
+ * @return 0 on success
+ */
+int lbs_set_tpc_cfg(struct lbs_private *priv, int enable, int8_t p0, int8_t p1,
+		int8_t p2, int usesnr)
+{
+	struct cmd_ds_802_11_tpc_cfg cmd;
+	int ret;
+
+	memset(&cmd, 0, sizeof(cmd));
+	cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+	cmd.action = cpu_to_le16(CMD_ACT_SET);
+	cmd.enable = !!enable;
+	cmd.usesnr = !!usesnr;
+	cmd.P0 = p0;
+	cmd.P1 = p1;
+	cmd.P2 = p2;
+
+	ret = lbs_cmd_with_response(priv, CMD_802_11_TPC_CFG, &cmd);
+
+	return ret;
+}
+
+/**
+ * @brief Configures the power adaptation settings.
+ *
+ * @param priv		A pointer to struct lbs_private structure
+ * @param enable	Power adaptation enable
+ * @param p0		Power level for 1, 2, 5.5 and 11 Mbps (dBm).
+ * @param p1		Power level for 6, 9, 12, 18, 22, 24 and 36 Mbps (dBm).
+ * @param p2		Power level for 48 and 54 Mbps (dBm).
+ *
+ * @return 0 on Success
+ */
+
+int lbs_set_power_adapt_cfg(struct lbs_private *priv, int enable, int8_t p0,
+		int8_t p1, int8_t p2)
+{
+	struct cmd_ds_802_11_pa_cfg cmd;
+	int ret;
+
+	memset(&cmd, 0, sizeof(cmd));
+	cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+	cmd.action = cpu_to_le16(CMD_ACT_SET);
+	cmd.enable = !!enable;
+	cmd.P0 = p0;
+	cmd.P1 = p1;
+	cmd.P2 = p2;
+
+	ret = lbs_cmd_with_response(priv, CMD_802_11_PA_CFG , &cmd);
+
+	return ret;
+}
+
+
 static struct cmd_ctrl_node *__lbs_cmd_async(struct lbs_private *priv,
 	uint16_t command, struct cmd_header *in_cmd, int in_cmd_size,
 	int (*callback)(struct lbs_private *, unsigned long, struct cmd_header *),
drivers/net/wireless/libertas/cmd.h +6 -0
index 9a35e15..d002160 100644
@@ -26,6 +26,12 @@ int __lbs_cmd(struct lbs_private *priv, uint16_t command,
 	      int (*callback)(struct lbs_private *, unsigned long, struct cmd_header *),
 	      unsigned long callback_arg);
 
+int lbs_set_power_adapt_cfg(struct lbs_private *priv, int enable, int8_t p0,
+		int8_t p1, int8_t p2);
+
+int lbs_set_tpc_cfg(struct lbs_private *priv, int enable, int8_t p0, int8_t p1,
+		int8_t p2, int usesnr);
+
 int lbs_cmd_copyback(struct lbs_private *priv, unsigned long extra,
 		     struct cmd_header *resp);
 
drivers/net/wireless/libertas/defs.h +9 -0
index c20fcf1..58d11a3 100644
@@ -189,6 +189,15 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in
 #define MRVDRV_CMD_UPLD_RDY		0x0008
 #define MRVDRV_CARDEVENT		0x0010
 
+
+/* Automatic TX control default levels */
+#define POW_ADAPT_DEFAULT_P0 13
+#define POW_ADAPT_DEFAULT_P1 15
+#define POW_ADAPT_DEFAULT_P2 18
+#define TPC_DEFAULT_P0 5
+#define TPC_DEFAULT_P1 10
+#define TPC_DEFAULT_P2 13
+
 /** TxPD status */
 
 /*	Station firmware use TxPD status field to report final Tx transmit
drivers/net/wireless/libertas/host.h +1 -0
index d1d0666..5004d76 100644
@@ -72,6 +72,7 @@
 #define CMD_802_11_INACTIVITY_TIMEOUT		0x0067
 #define CMD_802_11_SLEEP_PERIOD			0x0068
 #define CMD_802_11_TPC_CFG			0x0072
+#define CMD_802_11_PA_CFG			0x0073
 #define CMD_802_11_FW_WAKE_METHOD		0x0074
 #define CMD_802_11_SUBSCRIBE_EVENT		0x0075
 #define CMD_802_11_RATE_ADAPT_RATESET		0x0076
drivers/net/wireless/libertas/hostcmd.h +19 -5
index b4ae2c2..d9f9a12 100644
@@ -605,14 +605,28 @@ struct cmd_ds_802_11_eeprom_access {
 } __attribute__ ((packed));
 
 struct cmd_ds_802_11_tpc_cfg {
+	struct cmd_header hdr;
+
 	__le16 action;
-	u8 enable;
-	s8 P0;
-	s8 P1;
-	s8 P2;
-	u8 usesnr;
+	uint8_t enable;
+	int8_t P0;
+	int8_t P1;
+	int8_t P2;
+	uint8_t usesnr;
 } __attribute__ ((packed));
 
+
+struct cmd_ds_802_11_pa_cfg {
+	struct cmd_header hdr;
+
+	__le16 action;
+	uint8_t enable;
+	int8_t P0;
+	int8_t P1;
+	int8_t P2;
+} __attribute__ ((packed));
+
+
 struct cmd_ds_802_11_led_ctrl {
 	__le16 action;
 	__le16 numled;
drivers/net/wireless/libertas/wext.c +30 -2
index 641e1c6..caf6108 100644
@@ -1856,7 +1856,22 @@ static int lbs_set_txpow(struct net_device *dev, struct iw_request_info *info,
 	}
 
 	if (vwrq->fixed == 0) {
-		/* Auto power control */
+		/* User requests automatic tx power control, however there are
+		 * many auto tx settings.  For now use firmware defaults
+		 * (enable power adaptation and disable TPC) until we come up
+		 * with a good way to expose these to the user. */
+		if (priv->fwrelease < 0x09000000) {
+			ret = lbs_set_power_adapt_cfg(priv, 1,
+					POW_ADAPT_DEFAULT_P0,
+					POW_ADAPT_DEFAULT_P1,
+					POW_ADAPT_DEFAULT_P2);
+			if (ret)
+				goto out;
+		}
+		ret = lbs_set_tpc_cfg(priv, 0, TPC_DEFAULT_P0, TPC_DEFAULT_P1,
+				TPC_DEFAULT_P2, 1);
+		if (ret)
+			goto out;
 		dbm = priv->txpower_max;
 	} else {
 		/* Userspace check in iwrange if it should use dBm or mW,
@@ -1866,7 +1881,8 @@ static int lbs_set_txpow(struct net_device *dev, struct iw_request_info *info,
 			goto out;
 		}
 
-		/* Validate requested power level against firmware allowed levels */
+		/* Validate requested power level against firmware allowed
+		 * levels */
 		if (priv->txpower_min && (dbm < priv->txpower_min)) {
 			ret = -EINVAL;
 			goto out;
@@ -1876,6 +1892,18 @@ static int lbs_set_txpow(struct net_device *dev, struct iw_request_info *info,
 			ret = -EINVAL;
 			goto out;
 		}
+		if (priv->fwrelease < 0x09000000) {
+			ret = lbs_set_power_adapt_cfg(priv, 0,
+					POW_ADAPT_DEFAULT_P0,
+					POW_ADAPT_DEFAULT_P1,
+					POW_ADAPT_DEFAULT_P2);
+			if (ret)
+				goto out;
+		}
+		ret = lbs_set_tpc_cfg(priv, 0, TPC_DEFAULT_P0, TPC_DEFAULT_P1,
+				TPC_DEFAULT_P2, 1);
+		if (ret)
+			goto out;
 	}
 
 	/* If the radio was off, turn it on */
Signature · 1 line
1.5.4.3
Acked-by on v1 1/1
#1 lore raw
Quoted 8 lines · Anna Neal

iwconfig txpower can now be used to set tx power to fixed or auto. If set to auto the default firmware settings are used.

The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams noted the command was no longer supported in firmware V9+.

Thanks!

Quoted 228 lines
---
 drivers/net/wireless/libertas/cmd.c     |   64 +++++++++++++++++++++++++++++++
 drivers/net/wireless/libertas/cmd.h     |    6 +++
 drivers/net/wireless/libertas/defs.h    |    9 ++++
 drivers/net/wireless/libertas/host.h    |    1 +
 drivers/net/wireless/libertas/hostcmd.h |   24 +++++++++--
 drivers/net/wireless/libertas/wext.c    |   32 ++++++++++++++-
 6 files changed, 129 insertions(+), 7 deletions(-)
drivers/net/wireless/libertas/cmd.c +64 -0
index 7e818b0..a912fb6 100644
@@ -1927,6 +1927,70 @@ void lbs_ps_confirm_sleep(struct lbs_private *priv)
 }
 
 
+/**
+ * @brief Configures the transmission power control functionality.
+ *
+ * @param priv		A pointer to struct lbs_private structure
+ * @param enable	Transmission power control enable
+ * @param p0		Power level when link quality is good (dBm).
+ * @param p1		Power level when link quality is fair (dBm).
+ * @param p2		Power level when link quality is poor (dBm).
+ * @param usesnr	Use Signal to Noise Ratio in TPC
+ *
+ * @return 0 on success
+ */
+int lbs_set_tpc_cfg(struct lbs_private *priv, int enable, int8_t p0, int8_t p1,
+		int8_t p2, int usesnr)
+{
+	struct cmd_ds_802_11_tpc_cfg cmd;
+	int ret;
+
+	memset(&cmd, 0, sizeof(cmd));
+	cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+	cmd.action = cpu_to_le16(CMD_ACT_SET);
+	cmd.enable = !!enable;
+	cmd.usesnr = !!usesnr;
+	cmd.P0 = p0;
+	cmd.P1 = p1;
+	cmd.P2 = p2;
+
+	ret = lbs_cmd_with_response(priv, CMD_802_11_TPC_CFG, &cmd);
+
+	return ret;
+}
+
+/**
+ * @brief Configures the power adaptation settings.
+ *
+ * @param priv		A pointer to struct lbs_private structure
+ * @param enable	Power adaptation enable
+ * @param p0		Power level for 1, 2, 5.5 and 11 Mbps (dBm).
+ * @param p1		Power level for 6, 9, 12, 18, 22, 24 and 36 Mbps (dBm).
+ * @param p2		Power level for 48 and 54 Mbps (dBm).
+ *
+ * @return 0 on Success
+ */
+
+int lbs_set_power_adapt_cfg(struct lbs_private *priv, int enable, int8_t p0,
+		int8_t p1, int8_t p2)
+{
+	struct cmd_ds_802_11_pa_cfg cmd;
+	int ret;
+
+	memset(&cmd, 0, sizeof(cmd));
+	cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+	cmd.action = cpu_to_le16(CMD_ACT_SET);
+	cmd.enable = !!enable;
+	cmd.P0 = p0;
+	cmd.P1 = p1;
+	cmd.P2 = p2;
+
+	ret = lbs_cmd_with_response(priv, CMD_802_11_PA_CFG , &cmd);
+
+	return ret;
+}
+
+
 static struct cmd_ctrl_node *__lbs_cmd_async(struct lbs_private *priv,
 	uint16_t command, struct cmd_header *in_cmd, int in_cmd_size,
 	int (*callback)(struct lbs_private *, unsigned long, struct cmd_header *),
drivers/net/wireless/libertas/cmd.h +6 -0
index 9a35e15..d002160 100644
@@ -26,6 +26,12 @@ int __lbs_cmd(struct lbs_private *priv, uint16_t command,
 	      int (*callback)(struct lbs_private *, unsigned long, struct cmd_header *),
 	      unsigned long callback_arg);
 
+int lbs_set_power_adapt_cfg(struct lbs_private *priv, int enable, int8_t p0,
+		int8_t p1, int8_t p2);
+
+int lbs_set_tpc_cfg(struct lbs_private *priv, int enable, int8_t p0, int8_t p1,
+		int8_t p2, int usesnr);
+
 int lbs_cmd_copyback(struct lbs_private *priv, unsigned long extra,
 		     struct cmd_header *resp);
 
drivers/net/wireless/libertas/defs.h +9 -0
index c20fcf1..58d11a3 100644
@@ -189,6 +189,15 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in
 #define MRVDRV_CMD_UPLD_RDY		0x0008
 #define MRVDRV_CARDEVENT		0x0010
 
+
+/* Automatic TX control default levels */
+#define POW_ADAPT_DEFAULT_P0 13
+#define POW_ADAPT_DEFAULT_P1 15
+#define POW_ADAPT_DEFAULT_P2 18
+#define TPC_DEFAULT_P0 5
+#define TPC_DEFAULT_P1 10
+#define TPC_DEFAULT_P2 13
+
 /** TxPD status */
 
 /*	Station firmware use TxPD status field to report final Tx transmit
drivers/net/wireless/libertas/host.h +1 -0
index d1d0666..5004d76 100644
@@ -72,6 +72,7 @@
 #define CMD_802_11_INACTIVITY_TIMEOUT		0x0067
 #define CMD_802_11_SLEEP_PERIOD			0x0068
 #define CMD_802_11_TPC_CFG			0x0072
+#define CMD_802_11_PA_CFG			0x0073
 #define CMD_802_11_FW_WAKE_METHOD		0x0074
 #define CMD_802_11_SUBSCRIBE_EVENT		0x0075
 #define CMD_802_11_RATE_ADAPT_RATESET		0x0076
drivers/net/wireless/libertas/hostcmd.h +19 -5
index b4ae2c2..d9f9a12 100644
@@ -605,14 +605,28 @@ struct cmd_ds_802_11_eeprom_access {
 } __attribute__ ((packed));
 
 struct cmd_ds_802_11_tpc_cfg {
+	struct cmd_header hdr;
+
 	__le16 action;
-	u8 enable;
-	s8 P0;
-	s8 P1;
-	s8 P2;
-	u8 usesnr;
+	uint8_t enable;
+	int8_t P0;
+	int8_t P1;
+	int8_t P2;
+	uint8_t usesnr;
 } __attribute__ ((packed));
 
+
+struct cmd_ds_802_11_pa_cfg {
+	struct cmd_header hdr;
+
+	__le16 action;
+	uint8_t enable;
+	int8_t P0;
+	int8_t P1;
+	int8_t P2;
+} __attribute__ ((packed));
+
+
 struct cmd_ds_802_11_led_ctrl {
 	__le16 action;
 	__le16 numled;
drivers/net/wireless/libertas/wext.c +30 -2
index 641e1c6..caf6108 100644
@@ -1856,7 +1856,22 @@ static int lbs_set_txpow(struct net_device *dev, struct iw_request_info *info,
 	}
 
 	if (vwrq->fixed == 0) {
-		/* Auto power control */
+		/* User requests automatic tx power control, however there are
+		 * many auto tx settings.  For now use firmware defaults
+		 * (enable power adaptation and disable TPC) until we come up
+		 * with a good way to expose these to the user. */
+		if (priv->fwrelease < 0x09000000) {
+			ret = lbs_set_power_adapt_cfg(priv, 1,
+					POW_ADAPT_DEFAULT_P0,
+					POW_ADAPT_DEFAULT_P1,
+					POW_ADAPT_DEFAULT_P2);
+			if (ret)
+				goto out;
+		}
+		ret = lbs_set_tpc_cfg(priv, 0, TPC_DEFAULT_P0, TPC_DEFAULT_P1,
+				TPC_DEFAULT_P2, 1);
+		if (ret)
+			goto out;
 		dbm = priv->txpower_max;
 	} else {
 		/* Userspace check in iwrange if it should use dBm or mW,
@@ -1866,7 +1881,8 @@ static int lbs_set_txpow(struct net_device *dev, struct iw_request_info *info,
 			goto out;
 		}
 
-		/* Validate requested power level against firmware allowed levels */
+		/* Validate requested power level against firmware allowed
+		 * levels */
 		if (priv->txpower_min && (dbm < priv->txpower_min)) {
 			ret = -EINVAL;
 			goto out;
@@ -1876,6 +1892,18 @@ static int lbs_set_txpow(struct net_device *dev, struct iw_request_info *info,
 			ret = -EINVAL;
 			goto out;
 		}
+		if (priv->fwrelease < 0x09000000) {
+			ret = lbs_set_power_adapt_cfg(priv, 0,
+					POW_ADAPT_DEFAULT_P0,
+					POW_ADAPT_DEFAULT_P1,
+					POW_ADAPT_DEFAULT_P2);
+			if (ret)
+				goto out;
+		}
+		ret = lbs_set_tpc_cfg(priv, 0, TPC_DEFAULT_P0, TPC_DEFAULT_P1,
+				TPC_DEFAULT_P2, 1);
+		if (ret)
+			goto out;
 	}
 
 	/* If the radio was off, turn it on */
#2 lore raw
In reply to Anna Neal
Quoted 8 lines · Anna Neal

iwconfig txpower can now be used to set tx power to fixed or auto. If set to auto the default firmware settings are used.

The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams noted the command was no longer supported in firmware V9+.

I had already committed an earlier version. I believe I have incorporated all the changes in "libertas: Improvements on automatic tx power control via SIOCSIWTXPOW (fixups)" -- please feel free to verify.

Thanks,

John

Signature · 2 lines
John W. Linville		Linux should be at the core
[email protected]			of your literate lifestyle.
#3 lore raw
Quoted 7 lines · John W. Linville
Quoted 6 lines · Anna Neal

iwconfig txpower can now be used to set tx power to fixed or auto. If set to auto the default firmware settings are used.

The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams noted the command was no longer supported in firmware V9+.

Quoted 6 lines
Quoted 2 lines

I had already committed an earlier version. I believe I have incorporated all the changes in "libertas: Improvements on automatic tx power control via SIOCSIWTXPOW (fixups)" -- please feel free to verify.

A few missing bits, sorry for the confusion. Merge fixups against current wireless-testing below.

drivers/net/wireless/libertas/cmd.c +1 -1
index aee19fa..a912fb6 100644
@@ -1949,7 +1949,7 @@ int lbs_set_tpc_cfg(struct lbs_private *priv, int enable, int8_t p0, int8_t p1,
 	cmd.hdr.size = cpu_to_le16(sizeof(cmd));
 	cmd.action = cpu_to_le16(CMD_ACT_SET);
 	cmd.enable = !!enable;
-	cmd.usesnr = !!enable;
+	cmd.usesnr = !!usesnr;
 	cmd.P0 = p0;
 	cmd.P1 = p1;
 	cmd.P2 = p2;
drivers/net/wireless/libertas/defs.h +0 -10
index d21bb4e..076a636 100644
@@ -189,16 +189,6 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in
 #define MRVDRV_CMD_UPLD_RDY		0x0008
 #define MRVDRV_CARDEVENT		0x0010
 
-
-/* Automatic TX control default levels */
-#define POW_ADAPT_DEFAULT_P0 13
-#define POW_ADAPT_DEFAULT_P1 15
-#define POW_ADAPT_DEFAULT_P2 18
-#define TPC_DEFAULT_P0 5
-#define TPC_DEFAULT_P1 10
-#define TPC_DEFAULT_P2 13
-
-
 /* Automatic TX control default levels */
 #define POW_ADAPT_DEFAULT_P0 13
 #define POW_ADAPT_DEFAULT_P1 15
#4 lore raw
Quoted 11 lines · Dan Williams
Quoted 10 lines · John W. Linville
Quoted 8 lines · Anna Neal

iwconfig txpower can now be used to set tx power to fixed or auto. If set to auto the default firmware settings are used.

The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams noted the command was no longer supported in firmware V9+.

Quoted 8 lines
Quoted 3 lines

I had already committed an earlier version. I believe I have incorporated all the changes in "libertas: Improvements on automatic tx power control via SIOCSIWTXPOW (fixups)" -- please feel free to verify.

A few missing bits, sorry for the confusion. Merge fixups against current wireless-testing below.

Thanks Dan! I'll fold this into the patch before sending it upstream.

John

Signature · 2 lines
John W. Linville		Linux should be at the core
[email protected]			of your literate lifestyle.