Add nl80211 commands to get and set o11s mesh networking parameters

index 9bad654..40d7b27 100644
@@ -106,6 +106,12 @@
  * 	to the the specified ISO/IEC 3166-1 alpha2 country code. The core will
  * 	store this as a valid request and then query userspace for it.
  *
+ * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
+ *	interface identified by %NL80211_ATTR_IFINDEX
+ *
+ * @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the
+ *      interface identified by %NL80211_ATTR_IFINDEX
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */

@@ -148,6 +154,9 @@ enum nl80211_commands {
 	NL80211_CMD_SET_REG,
 	NL80211_CMD_REQ_SET_REG,
 
+	NL80211_CMD_GET_MESH_PARAMS,
+	NL80211_CMD_SET_MESH_PARAMS,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */

@@ -296,6 +305,8 @@ enum nl80211_attrs {
 	NL80211_ATTR_REG_ALPHA2,
 	NL80211_ATTR_REG_RULES,
 
+	NL80211_ATTR_MESH_PARAMS,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,

@@ -594,4 +605,79 @@ enum nl80211_mntr_flags {
 	NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1
 };
 
+/**
+ * enum nl80211_meshconf_params - mesh configuration parameters
+ *
+ * Mesh configuration parameters
+ *
+ * @__NL80211_MESHCONF_INVALID: internal use
+ *
+ * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in
+ * millisecond units, used by the Peer Link Open message
+ *
+ * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the inital confirm timeout, in
+ * millisecond units, used by the peer link management to close a peer link
+ *
+ * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in
+ * millisecond units
+ *
+ * @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed
+ * on this mesh interface
+ *
+ * @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link
+ * open retries that can be sent to establish a new peer link instance in a
+ * mesh
+ *
+ * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
+ * point.
+ *
+ * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically
+ * open peer links when we detect compatible mesh peers.
+ *
+ * @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames
+ * containing a PREQ that an MP can send to a particular destination (path
+ * target)
+ *
+ * @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths
+ * (in milliseconds)
+ *
+ * @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait
+ * until giving up on a path discovery (in milliseconds)
+ *
+ * @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh
+ * points receiving a PREQ shall consider the forwarding information from the
+ * root to be valid. (TU = time unit)
+ *
+ * @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in
+ * TUs) during which an MP can send only one action frame containing a PREQ
+ * reference element
+ *
+ * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
+ * that it takes for an HWMP information element to propagate across the mesh
+ *
+ * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
+ *
+ * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
+ */
+enum nl80211_meshconf_params {
+	__NL80211_MESHCONF_INVALID,
+	NL80211_MESHCONF_RETRY_TIMEOUT,
+	NL80211_MESHCONF_CONFIRM_TIMEOUT,
+	NL80211_MESHCONF_HOLDING_TIMEOUT,
+	NL80211_MESHCONF_MAX_PEER_LINKS,
+	NL80211_MESHCONF_MAX_RETRIES,
+	NL80211_MESHCONF_TTL,
+	NL80211_MESHCONF_AUTO_OPEN_PLINKS,
+	NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES,
+	NL80211_MESHCONF_PATH_REFRESH_TIME,
+	NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT,
+	NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT,
+	NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL,
+	NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME,
+
+	/* keep last */
+	__NL80211_MESHCONF_ATTR_AFTER_LAST,
+	NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1
+};
+
 #endif /* __LINUX_NL80211_H */

index 0e85ec3..03e1e88 100644
@@ -347,6 +347,25 @@ struct ieee80211_regdomain {
 	.flags = reg_flags, \
 	}
 
+struct mesh_config {
+	/* Timeouts in ms */
+	/* Mesh plink management parameters */
+	u16 dot11MeshRetryTimeout;
+	u16 dot11MeshConfirmTimeout;
+	u16 dot11MeshHoldingTimeout;
+	u16 dot11MeshMaxPeerLinks;
+	u8  dot11MeshMaxRetries;
+	u8  dot11MeshTTL;
+	bool auto_open_plinks;
+	/* HWMP parameters */
+	u8  dot11MeshHWMPmaxPREQretries;
+	u32 path_refresh_time;
+	u16 min_discovery_timeout;
+	u32 dot11MeshHWMPactivePathTimeout;
+	u16 dot11MeshHWMPpreqMinInterval;
+	u16 dot11MeshHWMPnetDiameterTraversalTime;
+};
+
 /* from net/wireless.h */
 struct wiphy;
 

@@ -397,6 +416,12 @@ struct wiphy;
  *
  * @change_station: Modify a given station.
  *
+ * @get_mesh_params: Put the current mesh parameters into *params
+ *
+ * @set_mesh_params: Set mesh parameters.
+ *	The mask is a bitfield which tells us which parameters to
+ *	set, and which to leave alone.
+ *
  * @set_mesh_cfg: set mesh parameters (by now, just mesh id)
  *
  * @change_bss: Modify parameters for a given BSS.

@@ -452,7 +477,12 @@ struct cfg80211_ops {
 	int	(*dump_mpath)(struct wiphy *wiphy, struct net_device *dev,
 			       int idx, u8 *dst, u8 *next_hop,
 			       struct mpath_info *pinfo);
-
+	int	(*get_mesh_params)(struct wiphy *wiphy,
+				struct net_device *dev,
+				struct mesh_config *conf);
+	int	(*set_mesh_params)(struct wiphy *wiphy,
+				struct net_device *dev,
+				const struct mesh_config *nconf, u32 mask);
 	int	(*change_bss)(struct wiphy *wiphy, struct net_device *dev,
 			      struct bss_parameters *params);
 };

80 lines not on this page · raw message

index 8198447..7a4a3c4 100644
@@ -23,6 +23,7 @@
 #include <linux/types.h>
 #include <linux/spinlock.h>
 #include <linux/etherdevice.h>
+#include <net/cfg80211.h>
 #include <net/wireless.h>
 #include <net/iw_handler.h>
 #include <net/mac80211.h>

@@ -255,26 +256,6 @@ struct mesh_preq_queue {
 	u8 flags;
 };
 
-struct mesh_config {
-	/* Timeouts in ms */
-	/* Mesh plink management parameters */
-	u16 dot11MeshRetryTimeout;
-	u16 dot11MeshConfirmTimeout;
-	u16 dot11MeshHoldingTimeout;
-	u16 dot11MeshMaxPeerLinks;
-	u8  dot11MeshMaxRetries;
-	u8  dot11MeshTTL;
-	bool auto_open_plinks;
-	/* HWMP parameters */
-	u8  dot11MeshHWMPmaxPREQretries;
-	u32 path_refresh_time;
-	u16 min_discovery_timeout;
-	u32 dot11MeshHWMPactivePathTimeout;
-	u16 dot11MeshHWMPpreqMinInterval;
-	u16 dot11MeshHWMPnetDiameterTraversalTime;
-};
-
-
 /* flags used in struct ieee80211_if_sta.flags */
 #define IEEE80211_STA_SSID_SET		BIT(0)
 #define IEEE80211_STA_BSSID_SET		BIT(1)

211 lines not on this page · raw message