exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
Forgive me if this isn't proper for this list but throughout sept-oct there was thread 'exception Emask 0x0 SAct 0x1 / SErr 0x0 action 0x2 frozen'. Discussion continued till mid October and then died off. It touched on issues with people seeing the following on disk intensive transactions I believe.
[11285.918535] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11285.918567] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11285.918568] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11285.918619] ata9.00: status: { DRDY }
[11285.918635] ata9: hard resetting linkAs of today I'm running:
Linux isis 2.6.27-7-server #1 SMP Tue Nov 4 20:16:57 UTC 2008 x86_64 GNU/Linux
I'm running a 7 disk software raid 5 on a SuperMicro AOC-SAT2-MV8:
SCSI storage controller: Marvell Technology Group Ltd. MV88SX6081 8-port SATAII PCI-X Controller (rev 09)
As far as the drives go, they're 500GB's each:
4 are Seagate ST3500630AS (7200.10)
3 are WDC WD5000AAKS-00YGA0 (yes i know, the dreaded AAKS) *The errors appear to happen on all of the drives; I've changed the ordering (because the logs make it appear that 3 drives are the ones with issues, and it just changes which drives report the errors).
The filesystem is XFS.
These problems manifested when i moved from CentOS 2.6.18 32bit to Ubuntu 2.6.27.2.2 64Bit. The drives and controller where rock solid. I reinstalled due to a mobo/cpu change so i cant with certainty say its not hardware related, but giving other peoples findings i would rule out the changed hardware. I even replaced the controller and cables with no change in results.
I initially reported this to the ubuntu bugtracker late august and just walked away from the system until today when i attempted to upgrade (to ubuntu 8.10) and try again.
Typical behavior: Upon transferring after about 20GB's or so it took out my raid and caused all the disks to desync. I managed to get all but one disk to resync but i _wont_ be stressing the raid (including a rebuild) until this issue is fixed so i'm not sure what more i can provide as far as logs go.
Bug behavior: On large transfers (I've honestly only tried 4-12GB transfers), the transfers seem to work at first, then stalls for ~30 seconds, recovers, transfer for 60 seconds or so, then stall again, constantly repeating this cycle.
Does _anyone_ have any update on this issue?
Original bug i created:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/263160/
similar posting it would seem:
https://bugzilla.redhat.com/show_bug.cgi?id=462425
*NOTE* yes these logs are 'old' but the current ones looked exactly the same. I didn't dump any recent ones due to that fact. I cant reproduce this anymore because i cant risk loosing the data in the raid.
dmesg:
[11285.918535] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11285.918567] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11285.918568] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11285.918619] ata9.00: status: { DRDY }
[11285.918635] ata9: hard resetting link
[11286.420039] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11286.460065] ata9.00: max_sectors limited to 256 for NCQ
[11286.520054] ata9.00: max_sectors limited to 256 for NCQ
[11286.520059] ata9.00: configured for UDMA/133
[11286.520077] ata9: EH complete
[11286.520119] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[11286.520132] sd 8:0:0:0: [sdd] Write Protect is off
[11286.520134] sd 8:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[11286.520154] sd 8:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[11326.988529] ata8.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11326.988554] ata8.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11326.988555] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11326.988606] ata8.00: status: { DRDY }
[11326.988623] ata8: hard resetting link
[11327.500037] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11327.580053] ata8.00: max_sectors limited to 256 for NCQ
[11327.657199] ata8.00: max_sectors limited to 256 for NCQ
[11327.657202] ata8.00: configured for UDMA/133
[11327.657207] ata8: EH complete
[11327.657257] sd 7:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[11327.657272] sd 7:0:0:0: [sdc] Write Protect is off
[11327.657273] sd 7:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[11327.657296] sd 7:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[11377.938532] ata7.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11377.938557] ata7.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11377.938558] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11377.938608] ata7.00: status: { DRDY }
[11377.938624] ata7: hard resetting link
[11378.440037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11378.520056] ata7.00: max_sectors limited to 256 for NCQ
[11378.600065] ata7.00: max_sectors limited to 256 for NCQ
[11378.600068] ata7.00: configured for UDMA/133
[11378.600073] ata7: EH complete
[11378.600120] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[11378.600133] sd 6:0:0:0: [sdb] Write Protect is off
[11378.600135] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[11378.600155] sd 6:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[11711.718523] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11711.718548] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11711.718549] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11711.718600] ata9.00: status: { DRDY }
[11711.718616] ata9: hard resetting link
[11712.220041] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11712.260058] ata9.00: max_sectors limited to 256 for NCQ
[11712.320057] ata9.00: max_sectors limited to 256 for NCQ
[11712.320066] ata9.00: configured for UDMA/133
[11712.320072] ata9: EH complete
[11712.320112] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[11712.320125] sd 8:0:0:0: [sdd] Write Protect is off
[11712.320127] sd 8:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[11712.320148] sd 8:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[11849.328524] ata7.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11849.328549] ata7.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11849.328549] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11849.328600] ata7.00: status: { DRDY }
[11849.328617] ata7: hard resetting link
[11849.830037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11849.910070] ata7.00: max_sectors limited to 256 for NCQ
[11849.990053] ata7.00: max_sectors limited to 256 for NCQ
[11849.990057] ata7.00: configured for UDMA/133
[11849.990069] ata7: EH complete
[11849.990109] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[11849.990123] sd 6:0:0:0: [sdb] Write Protect is off
[11849.990125] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[11849.990147] sd 6:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[11909.629773] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11909.629797] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11909.629798] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11909.629849] ata9.00: status: { DRDY }
[11909.629865] ata9: hard resetting link
[11910.131295] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11910.180068] ata9.00: max_sectors limited to 256 for NCQ
[11910.231316] ata9.00: max_sectors limited to 256 for NCQ
[11910.231319] ata9.00: configured for UDMA/133
[11910.231327] ata9: EH complete
[11910.231381] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[11910.231394] sd 8:0:0:0: [sdd] Write Protect is off
[11910.231396] sd 8:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[11910.231417] sd 8:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[11996.729773] ata7.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[11996.729797] ata7.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0
ncq 1536 out
[11996.729798] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11996.729848] ata7.00: status: { DRDY }
[11996.729865] ata7: hard resetting link
[11997.231291] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11997.311308] ata7.00: max_sectors limited to 256 for NCQ
[11997.391306] ata7.00: max_sectors limited to 256 for NCQ
[11997.391316] ata7.00: configured for UDMA/133
[11997.391322] ata7: EH complete
[11997.391366] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[11997.391378] sd 6:0:0:0: [sdb] Write Protect is off
[11997.391380] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[11997.391400] sd 6:0:0:0: [sdb] Write cache: enabled, read cache:enabled, doesn't support DPO or FU
/var/log/messages:
Aug 30 20:12:43 isis kernel: [11285.918635] ata9: hard resetting link Aug 30 20:12:43 isis kernel: [11286.420039] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:12:43 isis kernel: [11286.460065] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:12:43 isis kernel: [11286.520054] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:12:43 isis kernel: [11286.520059] ata9.00: configured for UDMA/133 Aug 30 20:12:43 isis kernel: [11286.520077] ata9: EH complete Aug 30 20:12:43 isis kernel: [11286.520119] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:12:43 isis kernel: [11286.520132] sd 8:0:0:0: [sdd] Write Protect is off Aug 30 20:12:43 isis kernel: [11286.520154] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:13:24 isis kernel: [11326.988623] ata8: hard resetting link Aug 30 20:13:24 isis kernel: [11327.500037] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:13:24 isis kernel: [11327.580053] ata8.00: max_sectors limited to 256 for NCQ Aug 30 20:13:24 isis kernel: [11327.657199] ata8.00: max_sectors limited to 256 for NCQ Aug 30 20:13:24 isis kernel: [11327.657202] ata8.00: configured for UDMA/133 Aug 30 20:13:24 isis kernel: [11327.657207] ata8: EH complete Aug 30 20:13:24 isis kernel: [11327.657257] sd 7:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:13:24 isis kernel: [11327.657272] sd 7:0:0:0: [sdc] Write Protect is off Aug 30 20:13:24 isis kernel: [11327.657296] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:14:15 isis kernel: [11377.938624] ata7: hard resetting link Aug 30 20:14:15 isis kernel: [11378.440037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:14:15 isis kernel: [11378.520056] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:14:15 isis kernel: [11378.600065] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:14:15 isis kernel: [11378.600068] ata7.00: configured for UDMA/133 Aug 30 20:14:15 isis kernel: [11378.600073] ata7: EH complete Aug 30 20:14:15 isis kernel: [11378.600120] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:14:15 isis kernel: [11378.600133] sd 6:0:0:0: [sdb] Write Protect is off Aug 30 20:14:15 isis kernel: [11378.600155] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:19:48 isis kernel: [11711.718616] ata9: hard resetting link Aug 30 20:19:49 isis kernel: [11712.220041] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:19:49 isis kernel: [11712.260058] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:19:49 isis kernel: [11712.320057] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:19:49 isis kernel: [11712.320066] ata9.00: configured for UDMA/133 Aug 30 20:19:49 isis kernel: [11712.320072] ata9: EH complete Aug 30 20:19:49 isis kernel: [11712.320112] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:19:49 isis kernel: [11712.320125] sd 8:0:0:0: [sdd] Write Protect is off Aug 30 20:19:49 isis kernel: [11712.320148] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:22:06 isis kernel: [11849.328617] ata7: hard resetting link Aug 30 20:22:06 isis kernel: [11849.830037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:22:06 isis kernel: [11849.910070] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:22:07 isis kernel: [11849.990053] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:22:07 isis kernel: [11849.990057] ata7.00: configured for UDMA/133 Aug 30 20:22:07 isis kernel: [11849.990069] ata7: EH complete Aug 30 20:22:07 isis kernel: [11849.990109] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:22:07 isis kernel: [11849.990123] sd 6:0:0:0: [sdb] Write Protect is off Aug 30 20:22:07 isis kernel: [11849.990147] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:23:06 isis kernel: [11909.629865] ata9: hard resetting link Aug 30 20:23:07 isis kernel: [11910.131295] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:23:07 isis kernel: [11910.180068] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:23:07 isis kernel: [11910.231316] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:23:07 isis kernel: [11910.231319] ata9.00: configured for UDMA/133 Aug 30 20:23:07 isis kernel: [11910.231327] ata9: EH complete Aug 30 20:23:07 isis kernel: [11910.231381] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:23:07 isis kernel: [11910.231394] sd 8:0:0:0: [sdd] Write Protect is off Aug 30 20:23:07 isis kernel: [11910.231417] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:24:33 isis kernel: [11996.729865] ata7: hard resetting link Aug 30 20:24:34 isis kernel: [11997.231291] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:24:34 isis kernel: [11997.311308] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:24:34 isis kernel: [11997.391306] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:24:34 isis kernel: [11997.391316] ata7.00: configured for UDMA/133 Aug 30 20:24:34 isis kernel: [11997.391322] ata7: EH complete Aug 30 20:24:34 isis kernel: [11997.391366] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:24:34 isis kernel: [11997.391378] sd 6:0:0:0: [sdb] Write Protect is off Aug 30 20:24:34 isis kernel: [11997.391400] sd 6:0:0:0: [sdb] Write
cache: enabled, read cache: enabled, doesn't support DPO or FUA
Quoted 11 lines · Corey Bertram
Forgive me if this isn't proper for this list but throughout sept-oct there was thread 'exception Emask
0x0SAct0x1/ SErr0x0action0x2frozen'. Discussion continued till mid October and then died off. It touched on issues with people seeing the following on disk intensive transactions I believe.[11285.918535] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11285.918567] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11285.918568] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11285.918619] ata9.00: status: { DRDY } [11285.918635] ata9: hard resetting link
First of all, I should caution that this is about the most generic error imaginable, a command timeout, so I'd caution against assuming that any other reports of the same message are due to the same cause.
Quoted 8 lines
As of today I'm running:
Linux isis 2.6.27-7-server #1 SMP Tue Nov 4 20:16:57 UTC 2008x86_64GNU/LinuxI'm running a 7 disk software raid 5 on a SuperMicro AOC-SAT2-MV8:
SCSI storage controller: Marvell Technology Group Ltd. MV88SX6081 8-port SATAII PCI-X Controller (rev 09)
Quoted 6 lines
As far as the drives go, they're 500GB's each:
4 are Seagate ST3500630AS (7200.10)
3 are WDC WD5000AAKS-00YGA0 (yes i know, the dreaded AAKS) *The errors appear to happen on all of the drives; I've changed the ordering (because the logs make it appear that 3 drives are the ones with issues, and it just changes which drives report the errors).
Is it always the same ports?
7 drives is a fair number, are you sure your PSU can handle it? These kinds of problems often turn out to be cabling issues, insufficient power, etc.
Quoted 254 lines
The filesystem is XFS.
These problems manifested when i moved from CentOS 2.6.18 32bit to Ubuntu 2.6.27.2.2 64Bit. The drives and controller where rock solid. I reinstalled due to a mobo/cpu change so i cant with certainty say its not hardware related, but giving other peoples findings i would rule out the changed hardware. I even replaced the controller and cables with no change in results.
I initially reported this to the ubuntu bugtracker late august and just walked away from the system until today when i attempted to upgrade (to ubuntu 8.10) and try again.
Typical behavior: Upon transferring after about 20GB's or so it took out my raid and caused all the disks to desync. I managed to get all but one disk to resync but i _wont_ be stressing the raid (including a rebuild) until this issue is fixed so i'm not sure what more i can provide as far as logs go.Bug behavior: On large transfers (I've honestly only tried 4-12GB transfers), the transfers seem to work at first, then stalls for ~30 seconds, recovers, transfer for 60 seconds or so, then stall again, constantly repeating this cycle.
Does _anyone_ have any update on this issue?
Original bug i created:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/263160/
similar posting it would seem:
https://bugzilla.redhat.com/show_bug.cgi?id=462425*NOTE* yes these logs are 'old' but the current ones looked exactly the same. I didn't dump any recent ones due to that fact. I cant reproduce this anymore because i cant risk loosing the data in the raid.
dmesg:[11285.918535] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11285.918567] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11285.918568] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11285.918619] ata9.00: status: { DRDY } [11285.918635] ata9: hard resetting link [11286.420039] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [11286.460065] ata9.00: max_sectors limited to 256 for NCQ [11286.520054] ata9.00: max_sectors limited to 256 for NCQ [11286.520059] ata9.00: configured for UDMA/133 [11286.520077] ata9: EH complete [11286.520119] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) [11286.520132] sd 8:0:0:0: [sdd] Write Protect is off [11286.520134] sd 8:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [11286.520154] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [11326.988529] ata8.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11326.988554] ata8.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11326.988555] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11326.988606] ata8.00: status: { DRDY } [11326.988623] ata8: hard resetting link [11327.500037] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [11327.580053] ata8.00: max_sectors limited to 256 for NCQ [11327.657199] ata8.00: max_sectors limited to 256 for NCQ [11327.657202] ata8.00: configured for UDMA/133 [11327.657207] ata8: EH complete [11327.657257] sd 7:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) [11327.657272] sd 7:0:0:0: [sdc] Write Protect is off [11327.657273] sd 7:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [11327.657296] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [11377.938532] ata7.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11377.938557] ata7.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11377.938558] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11377.938608] ata7.00: status: { DRDY } [11377.938624] ata7: hard resetting link [11378.440037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [11378.520056] ata7.00: max_sectors limited to 256 for NCQ [11378.600065] ata7.00: max_sectors limited to 256 for NCQ [11378.600068] ata7.00: configured for UDMA/133 [11378.600073] ata7: EH complete [11378.600120] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [11378.600133] sd 6:0:0:0: [sdb] Write Protect is off [11378.600135] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [11378.600155] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [11711.718523] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11711.718548] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11711.718549] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11711.718600] ata9.00: status: { DRDY } [11711.718616] ata9: hard resetting link [11712.220041] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [11712.260058] ata9.00: max_sectors limited to 256 for NCQ [11712.320057] ata9.00: max_sectors limited to 256 for NCQ [11712.320066] ata9.00: configured for UDMA/133 [11712.320072] ata9: EH complete [11712.320112] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) [11712.320125] sd 8:0:0:0: [sdd] Write Protect is off [11712.320127] sd 8:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [11712.320148] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [11849.328524] ata7.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11849.328549] ata7.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11849.328549] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11849.328600] ata7.00: status: { DRDY } [11849.328617] ata7: hard resetting link [11849.830037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [11849.910070] ata7.00: max_sectors limited to 256 for NCQ [11849.990053] ata7.00: max_sectors limited to 256 for NCQ [11849.990057] ata7.00: configured for UDMA/133 [11849.990069] ata7: EH complete [11849.990109] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [11849.990123] sd 6:0:0:0: [sdb] Write Protect is off [11849.990125] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [11849.990147] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [11909.629773] ata9.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11909.629797] ata9.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11909.629798] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11909.629849] ata9.00: status: { DRDY } [11909.629865] ata9: hard resetting link [11910.131295] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [11910.180068] ata9.00: max_sectors limited to 256 for NCQ [11910.231316] ata9.00: max_sectors limited to 256 for NCQ [11910.231319] ata9.00: configured for UDMA/133 [11910.231327] ata9: EH complete [11910.231381] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) [11910.231394] sd 8:0:0:0: [sdd] Write Protect is off [11910.231396] sd 8:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [11910.231417] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [11996.729773] ata7.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen [11996.729797] ata7.00: cmd 61/03:00:49:00:00/00:00:00:00:00/40 tag 0 ncq 1536 out [11996.729798] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [11996.729848] ata7.00: status: { DRDY } [11996.729865] ata7: hard resetting link [11997.231291] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [11997.311308] ata7.00: max_sectors limited to 256 for NCQ [11997.391306] ata7.00: max_sectors limited to 256 for NCQ [11997.391316] ata7.00: configured for UDMA/133 [11997.391322] ata7: EH complete [11997.391366] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [11997.391378] sd 6:0:0:0: [sdb] Write Protect is off [11997.391380] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [11997.391400] sd 6:0:0:0: [sdb] Write cache: enabled, read cache:enabled, doesn't support DPO or FU
/var/log/messages:Aug 30 20:12:43 isis kernel: [11285.918635] ata9: hard resetting link Aug 30 20:12:43 isis kernel: [11286.420039] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:12:43 isis kernel: [11286.460065] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:12:43 isis kernel: [11286.520054] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:12:43 isis kernel: [11286.520059] ata9.00: configured for UDMA/133 Aug 30 20:12:43 isis kernel: [11286.520077] ata9: EH complete Aug 30 20:12:43 isis kernel: [11286.520119] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:12:43 isis kernel: [11286.520132] sd 8:0:0:0: [sdd] Write Protect is off Aug 30 20:12:43 isis kernel: [11286.520154] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:13:24 isis kernel: [11326.988623] ata8: hard resetting link Aug 30 20:13:24 isis kernel: [11327.500037] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:13:24 isis kernel: [11327.580053] ata8.00: max_sectors limited to 256 for NCQ Aug 30 20:13:24 isis kernel: [11327.657199] ata8.00: max_sectors limited to 256 for NCQ Aug 30 20:13:24 isis kernel: [11327.657202] ata8.00: configured for UDMA/133 Aug 30 20:13:24 isis kernel: [11327.657207] ata8: EH complete Aug 30 20:13:24 isis kernel: [11327.657257] sd 7:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:13:24 isis kernel: [11327.657272] sd 7:0:0:0: [sdc] Write Protect is off Aug 30 20:13:24 isis kernel: [11327.657296] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:14:15 isis kernel: [11377.938624] ata7: hard resetting link Aug 30 20:14:15 isis kernel: [11378.440037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:14:15 isis kernel: [11378.520056] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:14:15 isis kernel: [11378.600065] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:14:15 isis kernel: [11378.600068] ata7.00: configured for UDMA/133 Aug 30 20:14:15 isis kernel: [11378.600073] ata7: EH complete Aug 30 20:14:15 isis kernel: [11378.600120] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:14:15 isis kernel: [11378.600133] sd 6:0:0:0: [sdb] Write Protect is off Aug 30 20:14:15 isis kernel: [11378.600155] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:19:48 isis kernel: [11711.718616] ata9: hard resetting link Aug 30 20:19:49 isis kernel: [11712.220041] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:19:49 isis kernel: [11712.260058] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:19:49 isis kernel: [11712.320057] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:19:49 isis kernel: [11712.320066] ata9.00: configured for UDMA/133 Aug 30 20:19:49 isis kernel: [11712.320072] ata9: EH complete Aug 30 20:19:49 isis kernel: [11712.320112] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:19:49 isis kernel: [11712.320125] sd 8:0:0:0: [sdd] Write Protect is off Aug 30 20:19:49 isis kernel: [11712.320148] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:22:06 isis kernel: [11849.328617] ata7: hard resetting link Aug 30 20:22:06 isis kernel: [11849.830037] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:22:06 isis kernel: [11849.910070] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:22:07 isis kernel: [11849.990053] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:22:07 isis kernel: [11849.990057] ata7.00: configured for UDMA/133 Aug 30 20:22:07 isis kernel: [11849.990069] ata7: EH complete Aug 30 20:22:07 isis kernel: [11849.990109] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:22:07 isis kernel: [11849.990123] sd 6:0:0:0: [sdb] Write Protect is off Aug 30 20:22:07 isis kernel: [11849.990147] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:23:06 isis kernel: [11909.629865] ata9: hard resetting link Aug 30 20:23:07 isis kernel: [11910.131295] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:23:07 isis kernel: [11910.180068] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:23:07 isis kernel: [11910.231316] ata9.00: max_sectors limited to 256 for NCQ Aug 30 20:23:07 isis kernel: [11910.231319] ata9.00: configured for UDMA/133 Aug 30 20:23:07 isis kernel: [11910.231327] ata9: EH complete Aug 30 20:23:07 isis kernel: [11910.231381] sd 8:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:23:07 isis kernel: [11910.231394] sd 8:0:0:0: [sdd] Write Protect is off Aug 30 20:23:07 isis kernel: [11910.231417] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 30 20:24:33 isis kernel: [11996.729865] ata7: hard resetting link Aug 30 20:24:34 isis kernel: [11997.231291] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Aug 30 20:24:34 isis kernel: [11997.311308] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:24:34 isis kernel: [11997.391306] ata7.00: max_sectors limited to 256 for NCQ Aug 30 20:24:34 isis kernel: [11997.391316] ata7.00: configured for UDMA/133 Aug 30 20:24:34 isis kernel: [11997.391322] ata7: EH complete Aug 30 20:24:34 isis kernel: [11997.391366] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) Aug 30 20:24:34 isis kernel: [11997.391378] sd 6:0:0:0: [sdb] Write Protect is off Aug 30 20:24:34 isis kernel: [11997.391400] sd 6:0:0:0: [sdb] Writecache: enabled, read cache: enabled, doesn't support DPO or FUA