BUG: in 2.6.23-rc3-git7 in do_cciss_intr

on x86_64, 4 proc, 8 GB RAM:

calling cciss_init+0x0/0x2e [cciss]
HP CISS Driver (v 3.6.20)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 54
cciss 0000:42:08.0: PCI INT A -> Link[LNKA] -> GSI 54 (level, high) -> IRQ 54
cciss0: <0x3238> at PCI 0000:42:08.0 IRQ 503 using DAC

BUG: unable to handle kernel NULL pointer dereference at 0000000000000248
IP: [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]
PGD 17e422067 PUD 17e423067 PMD 0
Oops: 0002 [1] SMP
CPU 2
Modules linked in: cciss(+) ehci_hcd ohci_hcd uhci_hcd
Pid: 0, comm: swapper Not tainted 2.6.27-rc3-git7 #1
RIP: 0010:[<ffffffffa001bb68>]  [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]
RSP: 0018:ffff88027f66fee8  EFLAGS: 00010007
RAX: 0000000000000000 RBX: ffff88007f840270 RCX: 000000000000000c
RDX: 0000000000000000 RSI: ffff88027e5c0000 RDI: ffff88027e5c0000
RBP: ffff88027f66ff18 R08: 0000000000000000 R09: ffff88017fa95e88
R10: 0000000000000000 R11: ffff88027f66ff48 R12: ffff88027e5c0000
R13: 0000000000000000 R14: 00000000000001f7 R15: 0000000000000086
FS:  0000000000680850(0000) GS:ffff88017fc02c80(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000248 CR3: 000000017e425000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff88017fa94000, task ffff88027f63d340)
Stack:  ffff88027f66fee0 ffff88017e9b4800 0000000000000000 0000000000000000
 00000000000001f7 0000000000000000 ffff88027f66ff48 ffffffff8026757e
 ffffffff80719000 00000000000001f7 ffff88017e9b4800 ffffffff80719050
Call Trace:
 <IRQ>  [<ffffffff8026757e>] handle_IRQ_event+0x27/0x57
 [<ffffffff80268d08>] handle_edge_irq+0xed/0x12e
 [<ffffffff8020eaab>] do_IRQ+0xf6/0x167
 [<ffffffff8020c471>] ret_from_intr+0x0/0xa
 <EOI>  [<ffffffff802122b1>] ? default_idle+0x2b/0x40
 [<ffffffff802124bf>] ? c1e_idle+0xd4/0xdb
 [<ffffffff8055677d>] ? atomic_notifier_call_chain+0xf/0x11
 [<ffffffff8020ac6c>] ? cpu_idle+0x71/0x8f
 [<ffffffff8054e752>] ? start_secondary+0x157/0x15c


Code: 8b 83 48 02 00 00 48 39 d8 74 37 49 39 9c 24 c0 00 01 00 75 08 49 89 84 24 c0 00 01 00 48 8b 83 40 02 00 00 48 8b 93 48 02 00 00 <48> 89 90 48 02 00 00 48 8b 93 48 02 00 00 48 89 82 40 02 00 00
RIP  [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]
 RSP <ffff88027f66fee8>
CR2: 0000000000000248
---[ end trace 902dc79a9e72d3ed ]---

Is it repeatable?

Is it a regression?

Any chance of finding the offending code with gdb?

Randy,
Sorry I haven't replied sooner. I saw your earlier mail, just been busy breaking stuff internally. Did this happen during driver init or runtime?

-- mikem

Hi Mike,

It's very much during driver init.

Full boot log and .config are attached.

Andrew: I'll rerun the test ASAP. Machine is busy atm.

---
~Randy
Linux Plumbers Conference, 17-19 September 2008, Portland, Oregon USA
http://linuxplumbersconf.org/

Linux version 2.6.27-rc3-git7 ([email protected]) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #1 SMP Wed Aug 20 16:45:40 PDT 2008 Command line: root=LABEL=/ selinux=0 console=tty0 [email protected]/eth0,[email protected]/00:18:FE:34:1C:3D debug ignore_loglevel initcall_debug 3 kex KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000100 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fe50000 (usable)
BIOS-e820: 000000007fe50000 - 000000007fe58000 (ACPI data)
BIOS-e820: 000000007fe58000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000027ffff000 (usable)
debug: ignoring loglevel setting.
last_pfn = 0x27ffff max_arch_pfn = 0x3ffffffff
last_pfn = 0x7fe50 max_arch_pfn = 0x3ffffffff
init_memory_mapping
0000000000 - 007fe00000 page 2M
007fe00000 - 007fe50000 page 4k
kernel direct mapping tables up to 7fe50000 @ 8000-c000
last_map_addr: 7fe50000 end: 7fe50000
init_memory_mapping
0100000000 - 027fe00000 page 2M
027fe00000 - 027ffff000 page 4k
kernel direct mapping tables up to 27ffff000 @ a000-16000
last_map_addr: 27ffff000 end: 27ffff000
RAMDISK: 7fd05000 - 7fe4f87e
DMI 2.3 present.
ACPI: RSDP 000F4F00, 0024 (r2 HP )
ACPI: XSDT 7FE50780, 005C (r1 HP A08 2 � 162E)
ACPI: FACP 7FE50800, 00F4 (r3 HP A08 2 � 162E)
ACPI: DSDT 7FE50900, 3F75 (r1 HP DSDT 1 INTL 20030228)
ACPI: FACS 7FE50100, 0040
ACPI: SPCR 7FE50140, 0050 (r1 HP SPCRRBSU 1 � 162E)
ACPI: MCFG 7FE501C0, 003C (r1 HP ProLiant 1 0)
ACPI: HPET 7FE50200, 0038 (r1 HP A08 2 � 162E)
ACPI: SPMI 7FE50240, 0040 (r5 HP ProLiant 1 � 162E)
ACPI: APIC 7FE50280, 00DE (r1 HP 00000083 2 0)
ACPI: SRAT 7FE50380, 0110 (r1 AMD HAMMER 1 AMD 1)
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: Node 0 PXM 0 0-a0000
SRAT: Node 0 PXM 0 100000-80000000
SRAT: Node 0 PXM 0 100000000-180000000
SRAT: Node 1 PXM 1 180000000-280000000
NUMA: Allocated memnodemap from 11000 - 16080
NUMA: Using 20 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000180000000
NODE_DATA [0000000000001000 - 0000000000004fff]
bootmap [0000000000017000 - 0000000000046fff] pages 30
(8 early reservations) ==> bootmem [0000000000 - 0180000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 000086c4d0] TEXT DATA BSS ==> [0000200000 - 000086c4d0]
#3 [007fd05000 - 007fe4f87e] RAMDISK ==> [007fd05000 - 007fe4f87e]
#4 [000009f400 - 0000100000] BIOS reserved ==> [000009f400 - 0000100000]
#5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
#6 [000000a000 - 0000011000] PGTABLE ==> [000000a000 - 0000011000]
#7 [0000011000 - 0000016080] MEMNODEMAP ==> [0000011000 - 0000016080]
Bootmem setup node 1 0000000180000000-000000027ffff000
NODE_DATA [0000000180000000 - 0000000180003fff]
bootmap [0000000180004000 - 0000000180023fff] pages 20
(8 early reservations) ==> bootmem [0180000000 - 027ffff000]
#0 [0000000000 - 0000001000] BIOS data page
#1 [0000006000 - 0000008000] TRAMPOLINE
#2 [0000200000 - 000086c4d0] TEXT DATA BSS
#3 [007fd05000 - 007fe4f87e] RAMDISK
#4 [000009f400 - 0000100000] BIOS reserved
#5 [0000008000 - 000000a000] PGTABLE
#6 [000000a000 - 0000011000] PGTABLE
#7 [0000011000 - 0000016080] MEMNODEMAP
found SMP MP-table at [ffff8800000f4f80] 000f4f80
[ffffe20000000000-ffffe200053fffff] PMD -> [ffff880028200000-ffff88002b9fffff] on node 0
[ffffe20005400000-ffffe20008bfffff] PMD -> [ffff880180200000-ffff8801839fffff] on node 1
Zone PFN ranges:

  DMA      0x00000001 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x0027ffff
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
    0: 0x00000001 -> 0x0000009f
    0: 0x00000100 -> 0x0007fe50
    0: 0x00100000 -> 0x00180000
    1: 0x00180000 -> 0x0027ffff

On node 0 totalpages: 1048046
DMA zone: 2183 pages, LIFO batch:0
DMA32 zone: 505480 pages, LIFO batch:31
Normal zone: 517120 pages, LIFO batch:31
On node 1 totalpages: 1048575
Normal zone: 1034239 pages, LIFO batch:31
Detected use of extended apic ids on hypertransport bus
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x908
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xf7df0000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 0, address 0xf7df0000, GSI 0-23
ACPI: IOAPIC (id[0x09] address[0xfdef0000] gsi_base[38])
IOAPIC[1]: apic_id 9, version 0, address 0xfdef0000, GSI 38-61
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10228201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
PM: Registered nosave memory: 000000007fe50000 - 000000007fe58000
PM: Registered nosave memory: 000000007fe58000 - 0000000080000000
PM: Registered nosave memory: 0000000080000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000
PM: Registered nosave memory: 00000000fed00000 - 00000000ffc00000
PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
PERCPU: Allocating 47784 bytes of per cpu data
NR_CPUS: 8, nr_cpu_ids: 4, nr_node_ids 2
Built 2 zonelists in Zone order, mobility grouping on. Total pages: 2059022
Policy zone: Normal
Kernel command line: root=LABEL=/ selinux=0 console=tty0 [email protected]/eth0,[email protected]/00:18:FE:34:1C:3D debug ignore_loglevel initcall_debug 3 kex Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
Detected 1004.627 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
No AGP bridge found
Node 0: aperture @ c000000 size 64 MB
Aperture pointing to e820 RAM. Ignoring.
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 20000000
PM: Registered nosave memory: 0000000020000000 - 0000000024000000
Memory: 8197672k/10485756k available (3436k kernel code, 188812k reserved, 1715k data, 396k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=2
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 2009.25 BogoMIPS (lpj=4018508)
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
tseg: 0000000000
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
using C1E aware idle routine
ACPI: Core revision 20080609
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Dual-Core AMD Opteron(tm) Processor 8218 stepping 02
Using local APIC timer interrupts.
APIC timer calibration result 12557859
Detected 12.557 MHz APIC timer.
calling migration_init+0x0/0x5b
initcall migration_init+0x0/0x5b returned 1 after 0 msecs
initcall migration_init+0x0/0x5b returned with error code 1
calling spawn_ksoftirqd+0x0/0x58
initcall spawn_ksoftirqd+0x0/0x58 returned 0 after 0 msecs
calling init_call_single_data+0x0/0x47
initcall init_call_single_data+0x0/0x47 returned 0 after 0 msecs
calling spawn_softlockup_task+0x0/0x74
initcall spawn_softlockup_task+0x0/0x74 returned 0 after 0 msecs
calling relay_init+0x0/0x14
initcall relay_init+0x0/0x14 returned 0 after 0 msecs
Booting processor 1/2 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 2009.34 BogoMIPS (lpj=4018684)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/2 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
CPU1: Dual-Core AMD Opteron(tm) Processor 8218 stepping 02
Booting processor 2/1 ip 6000
Initializing CPU#2
Calibrating delay using timer specific routine.. 2009.42 BogoMIPS (lpj=4018850)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU2: Dual-Core AMD Opteron(tm) Processor 8218 stepping 02
Booting processor 3/3 ip 6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 2009.36 BogoMIPS (lpj=4018726)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3/3 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
CPU3: Dual-Core AMD Opteron(tm) Processor 8218 stepping 02
Brought up 4 CPUs
Total of 4 processors activated (8037.38 BogoMIPS).
khelper used greatest stack depth: 6008 bytes left
calling init_cpufreq_transition_notifier_list+0x0/0x1b
initcall init_cpufreq_transition_notifier_list+0x0/0x1b returned 0 after 0 msecs
calling net_ns_init+0x0/0x15d
net_namespace: 592 bytes
initcall net_ns_init+0x0/0x15d returned 0 after 0 msecs
calling cpufreq_tsc+0x0/0x16
initcall cpufreq_tsc+0x0/0x16 returned 0 after 0 msecs
calling init_smp_flush+0x0/0x41
initcall init_smp_flush+0x0/0x41 returned 0 after 0 msecs
calling sysctl_init+0x0/0x16
initcall sysctl_init+0x0/0x16 returned 0 after 0 msecs
calling ksysfs_init+0x0/0xbb
initcall ksysfs_init+0x0/0xbb returned 0 after 0 msecs
calling init_jiffies_clocksource+0x0/0x12
initcall init_jiffies_clocksource+0x0/0x12 returned 0 after 0 msecs
calling pm_init+0x0/0x34
initcall pm_init+0x0/0x34 returned 0 after 0 msecs
calling pm_disk_init+0x0/0x19
initcall pm_disk_init+0x0/0x19 returned 0 after 0 msecs
calling swsusp_header_init+0x0/0x2c
initcall swsusp_header_init+0x0/0x2c returned 0 after 0 msecs
calling filelock_init+0x0/0x2e
initcall filelock_init+0x0/0x2e returned 0 after 0 msecs
calling init_misc_binfmt+0x0/0x3f
initcall init_misc_binfmt+0x0/0x3f returned 0 after 0 msecs
calling init_script_binfmt+0x0/0x12
initcall init_script_binfmt+0x0/0x12 returned 0 after 0 msecs
calling init_elf_binfmt+0x0/0x12
initcall init_elf_binfmt+0x0/0x12 returned 0 after 0 msecs
calling init_compat_elf_binfmt+0x0/0x12
initcall init_compat_elf_binfmt+0x0/0x12 returned 0 after 0 msecs
calling debugfs_init+0x0/0x51
initcall debugfs_init+0x0/0x51 returned 0 after 0 msecs
calling random32_init+0x0/0xcc
initcall random32_init+0x0/0xcc returned 0 after 0 msecs
calling cpufreq_core_init+0x0/0x76
initcall cpufreq_core_init+0x0/0x76 returned 0 after 0 msecs
calling cpuidle_init+0x0/0x40
initcall cpuidle_init+0x0/0x40 returned 0 after 0 msecs
calling sock_init+0x0/0x59
initcall sock_init+0x0/0x59 returned 0 after 0 msecs
calling netpoll_init+0x0/0x31
initcall netpoll_init+0x0/0x31 returned 0 after 0 msecs
calling netlink_proto_init+0x0/0x14d
NET: Registered protocol family 16
initcall netlink_proto_init+0x0/0x14d returned 0 after 3 msecs
calling bdi_class_init+0x0/0x41
initcall bdi_class_init+0x0/0x41 returned 0 after 0 msecs
calling kobject_uevent_init+0x0/0x45
initcall kobject_uevent_init+0x0/0x45 returned 0 after 0 msecs
calling pcibus_class_init+0x0/0x19
initcall pcibus_class_init+0x0/0x19 returned 0 after 0 msecs
calling pci_driver_init+0x0/0x12
initcall pci_driver_init+0x0/0x12 returned 0 after 0 msecs
calling backlight_class_init+0x0/0x4d
initcall backlight_class_init+0x0/0x4d returned 0 after 0 msecs
calling tty_class_init+0x0/0x31
initcall tty_class_init+0x0/0x31 returned 0 after 0 msecs
calling vtconsole_class_init+0x0/0xc3
initcall vtconsole_class_init+0x0/0xc3 returned 0 after 0 msecs
calling register_node_type+0x0/0x6b
initcall register_node_type+0x0/0x6b returned 0 after 0 msecs
calling enable_pci_io_ecs+0x0/0x2e
initcall enable_pci_io_ecs+0x0/0x2e returned 0 after 0 msecs
calling early_fill_mp_bus_info+0x0/0x7ed
node 0 link 1: io port [1000, 3fff]
node 1 link 2: io port [4000, ffff]
TOM: 0000000080000000 aka 2048M
node 0 link 1: mmio [e8000000, fddfffff]
node 1 link 2: mmio [fde00000, fdffffff]
node 0 link 1: mmio [80000000, 83ffffff]
node 1 link 2: mmio [84000000, 8fffffff]
node 0 link 1: mmio [a0000, bffff]
TOM2: 0000000280000000 aka 10240M
bus: [00,3f] on node 0 link 1
bus: 00 index 0 io port: [0, 3fff]
bus: 00 index 1 mmio: [90000000, fddfffff]
bus: 00 index 2 mmio: [80000000, 83ffffff]
bus: 00 index 3 mmio: [a0000, bffff]
bus: 00 index 4 mmio: [fe000000, ffffffff]
bus: 00 index 5 mmio: [280000000, fcffffffff]
bus: [40,ff] on node 1 link 2
bus: 40 index 0 io port: [4000, ffff]
bus: 40 index 1 mmio: [fde00000, fdffffff]
bus: 40 index 2 mmio: [84000000, 8fffffff]
initcall early_fill_mp_bus_info+0x0/0x7ed returned 0 after 3 msecs
calling arch_kdebugfs_init+0x0/0x24
initcall arch_kdebugfs_init+0x0/0x24 returned 0 after 0 msecs
calling mtrr_if_init+0x0/0x77
initcall mtrr_if_init+0x0/0x77 returned 0 after 0 msecs
calling ffh_cstate_init+0x0/0x31
initcall ffh_cstate_init+0x0/0x31 returned -1 after 0 msecs
initcall ffh_cstate_init+0x0/0x31 returned with error code -1
calling acpi_pci_init+0x0/0x57
ACPI: bus type pci registered
initcall acpi_pci_init+0x0/0x57 returned 0 after 0 msecs
calling init_acpi_device_notify+0x0/0x4b
initcall init_acpi_device_notify+0x0/0x4b returned 0 after 0 msecs
calling dmi_id_init+0x0/0x2f0
initcall dmi_id_init+0x0/0x2f0 returned 0 after 0 msecs
calling pci_arch_init+0x0/0x4e
PCI: MCFG configuration 0: base 80000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
PCI: HP ProLiant BL685c G1 detected, enabling pci=bfsort.
initcall pci_arch_init+0x0/0x4e returned 0 after 3 msecs
calling topology_init+0x0/0x73
initcall topology_init+0x0/0x73 returned 0 after 0 msecs
calling mtrr_init_finialize+0x0/0x3d
initcall mtrr_init_finialize+0x0/0x3d returned 0 after 0 msecs
calling param_sysfs_init+0x0/0x1e7
initcall param_sysfs_init+0x0/0x1e7 returned 0 after 3 msecs
calling pm_sysrq_init+0x0/0x19
initcall pm_sysrq_init+0x0/0x19 returned 0 after 0 msecs
calling readahead_init+0x0/0x38
initcall readahead_init+0x0/0x38 returned 0 after 0 msecs
calling init_bio+0x0/0xc5
initcall init_bio+0x0/0xc5 returned 0 after 0 msecs
calling blk_settings_init+0x0/0x2a
initcall blk_settings_init+0x0/0x2a returned 0 after 0 msecs
calling blk_ioc_init+0x0/0x2a
initcall blk_ioc_init+0x0/0x2a returned 0 after 0 msecs
calling genhd_device_init+0x0/0x55
initcall genhd_device_init+0x0/0x55 returned 0 after 0 msecs
calling pci_slot_init+0x0/0x45
initcall pci_slot_init+0x0/0x45 returned 0 after 0 msecs
calling fbmem_init+0x0/0x91
initcall fbmem_init+0x0/0x91 returned 0 after 0 msecs
calling acpi_init+0x0/0x21d
ACPI: EC: Look up EC in DSDT
ACPI: SSDT 7FE58000, 04F0 (r2 HP PNOWSSDT 2 HP 1)
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base 80000000 segment 0 buses 0 - 255
PCI: MCFG area at 80000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at 80000000 - 8fffffff
initcall acpi_init+0x0/0x21d returned 0 after 22 msecs
calling acpi_scan_init+0x0/0x11e
initcall acpi_scan_init+0x0/0x11e returned 0 after 7 msecs
calling acpi_ec_init+0x0/0x61
initcall acpi_ec_init+0x0/0x61 returned 0 after 0 msecs
calling acpi_pci_root_init+0x0/0x28
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: supports D1
pci 0000:00:02.0: supports D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.1: supports D1
pci 0000:00:02.1: supports D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.1: PME# disabled
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0c.0: PME# disabled
pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0d.0: PME# disabled
pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0e.0: PME# disabled
pci 0000:01:03.0: supports D1
pci 0000:01:03.0: supports D2
pci 0000:01:04.0: PME# supported from D0 D3hot D3cold
pci 0000:01:04.0: PME# disabled
pci 0000:01:04.2: PME# supported from D0 D3hot D3cold
pci 0000:01:04.2: PME# disabled
pci 0000:01:04.4: PME# supported from D0 D3hot D3cold
pci 0000:01:04.4: PME# disabled
pci 0000:01:04.6: PME# supported from D0 D3hot D3cold
pci 0000:01:04.6: PME# disabled
pci 0000:00:09.0: transparent bridge
PCI: bridge 0000:00:09.0 io port: [1000, 2fff]
PCI: bridge 0000:00:09.0 32bit mmio: [f7e00000, f7ffffff]
PCI: bridge 0000:00:09.0 32bit mmio pref: [e8000000, efffffff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
PCI: bridge 0000:00:0b.0 32bit mmio: [f8000000, f9ffffff]
PCI: bridge 0000:00:0b.0 64bit mmio pref: [90000000, 900fffff]
pci 0000:03:00.0: PME# supported from D3hot D3cold
pci 0000:03:00.0: PME# disabled
PCI: bridge 0000:02:00.0 32bit mmio: [f8000000, f9ffffff]
PCI: bridge 0000:02:00.0 64bit mmio pref: [90000000, 900fffff]
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
PCI: bridge 0000:00:0c.0 32bit mmio: [fa000000, fbffffff]
PCI: bridge 0000:00:0c.0 64bit mmio pref: [90100000, 901fffff]
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
PCI: bridge 0000:04:00.0 32bit mmio: [fa000000, fbffffff]
PCI: bridge 0000:04:00.0 64bit mmio pref: [90100000, 901fffff]
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
PCI: bridge 0000:00:0d.0 32bit mmio: [fdc00000, fdcfffff]
PCI: bridge 0000:00:0d.0 64bit mmio pref: [90200000, 902fffff]
pci 0000:07:04.0: PME# supported from D3hot D3cold
pci 0000:07:04.0: PME# disabled
pci 0000:07:04.1: PME# supported from D3hot D3cold
pci 0000:07:04.1: PME# disabled
PCI: bridge 0000:06:00.0 32bit mmio: [fdc00000, fdcfffff]
PCI: bridge 0000:06:00.0 64bit mmio pref: [90200000, 902fffff]
PCI: bridge 0000:00:0e.0 io port: [3000, 3fff]
PCI: bridge 0000:00:0e.0 32bit mmio: [fdd00000, fddfffff]
PCI: bridge 0000:00:0e.0 64bit mmio pref: [90300000, 903fffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE1.NB01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE2.NC1B._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE3.NC2B._PRT]
ACPI: PCI Root Bridge [PCI1] (0000:40)
pci 0000:40:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:40:0c.0: PME# disabled
pci 0000:40:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:40:0d.0: PME# disabled
pci 0000:40:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:40:0e.0: PME# disabled
pci 0000:41:00.0: PME# supported from D0 D3hot D3cold
pci 0000:41:00.0: PME# disabled
PCI: bridge 0000:40:0c.0 io port: [4000, 4fff]
PCI: bridge 0000:40:0c.0 32bit mmio: [fdf00000, fdffffff]
PCI: bridge 0000:40:0c.0 64bit mmio pref: [90400000, 904fffff]
pci 0000:42:08.0: supports D1
PCI: bridge 0000:41:00.0 io port: [4000, 4fff]
PCI: bridge 0000:41:00.0 32bit mmio: [fdf00000, fdffffff]
PCI: bridge 0000:41:00.0 64bit mmio pref: [90400000, 904fffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE2.SASB._PRT]
initcall acpi_pci_root_init+0x0/0x28 returned 0 after 30 msecs
calling acpi_pci_link_init+0x0/0x48
ACPI: PCI Interrupt Link [LNKW] (IRQs *16)
ACPI: PCI Interrupt Link [LNKX] (IRQs *17)
ACPI: PCI Interrupt Link [LNKY] (IRQs *18)
ACPI: PCI Interrupt Link [LNKZ] (IRQs *19)
ACPI: PCI Interrupt Link [LNU0] (IRQs *22)
ACPI: PCI Interrupt Link [LNU2] (IRQs *23)
ACPI: PCI Interrupt Link [LNKA] (IRQs *54)
ACPI: PCI Interrupt Link [LNKB] (IRQs 55) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 56) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 57) *0, disabled.
initcall acpi_pci_link_init+0x0/0x48 returned 0 after 7 msecs
calling acpi_power_init+0x0/0x77
initcall acpi_power_init+0x0/0x77 returned 0 after 0 msecs
calling acpi_system_init+0x0/0x260
initcall acpi_system_init+0x0/0x260 returned 0 after 0 msecs
calling acpi_cm_sbs_init+0x0/0x8
initcall acpi_cm_sbs_init+0x0/0x8 returned 0 after 0 msecs
calling pnp_init+0x0/0x20
Linux Plug and Play Support v0.97 (c) Adam Belay
initcall pnp_init+0x0/0x20 returned 0 after 0 msecs
calling pnpacpi_init+0x0/0x8c
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
initcall pnpacpi_init+0x0/0x8c returned 0 after 7 msecs
calling misc_init+0x0/0x9f
initcall misc_init+0x0/0x9f returned 0 after 0 msecs
calling cn_init+0x0/0xee
initcall cn_init+0x0/0xee returned 0 after 0 msecs
calling phy_init+0x0/0x31
initcall phy_init+0x0/0x31 returned 0 after 0 msecs
calling init_scsi+0x0/0x91
SCSI subsystem initialized
initcall init_scsi+0x0/0x91 returned 0 after 0 msecs
calling usb_init+0x0/0x122
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
initcall usb_init+0x0/0x122 returned 0 after 0 msecs
calling serio_init+0x0/0x89
initcall serio_init+0x0/0x89 returned 0 after 0 msecs
calling input_init+0x0/0x10e
initcall input_init+0x0/0x10e returned 0 after 0 msecs
calling rtc_init+0x0/0x71
initcall rtc_init+0x0/0x71 returned 0 after 0 msecs
calling i2c_init+0x0/0x66
initcall i2c_init+0x0/0x66 returned 0 after 0 msecs
calling power_supply_class_init+0x0/0x38
initcall power_supply_class_init+0x0/0x38 returned 0 after 0 msecs
calling hwmon_init+0x0/0x42
initcall hwmon_init+0x0/0x42 returned 0 after 0 msecs
calling thermal_init+0x0/0x58
initcall thermal_init+0x0/0x58 returned 0 after 0 msecs
calling pci_subsys_init+0x0/0x12c
PCI: Using ACPI for IRQ routing
pci 0000:40:0c.0: BAR 9: can't allocate resource
pci 0000:41:00.0: BAR 9: can't allocate resource
initcall pci_subsys_init+0x0/0x12c returned 0 after 0 msecs
calling proto_init+0x0/0x2e
initcall proto_init+0x0/0x2e returned 0 after 0 msecs
calling net_dev_init+0x0/0x146
initcall net_dev_init+0x0/0x146 returned 0 after 0 msecs
calling neigh_init+0x0/0x71
initcall neigh_init+0x0/0x71 returned 0 after 0 msecs
calling fib_rules_init+0x0/0xa6
initcall fib_rules_init+0x0/0xa6 returned 0 after 0 msecs
calling genl_init+0x0/0xd9
initcall genl_init+0x0/0xd9 returned 0 after 15 msecs
calling sysctl_init+0x0/0x49
initcall sysctl_init+0x0/0x49 returned 0 after 0 msecs
calling pci_iommu_init+0x0/0x12
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 20000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
initcall pci_iommu_init+0x0/0x12 returned 0 after 3 msecs
calling hpet_late_init+0x0/0x114
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
initcall hpet_late_init+0x0/0x114 returned 0 after 0 msecs
calling clocksource_done_booting+0x0/0x12
initcall clocksource_done_booting+0x0/0x12 returned 0 after 0 msecs
calling init_pipe_fs+0x0/0x4c
initcall init_pipe_fs+0x0/0x4c returned 0 after 0 msecs
calling init_mnt_writers+0x0/0x47
initcall init_mnt_writers+0x0/0x47 returned 0 after 0 msecs
calling eventpoll_init+0x0/0x85
initcall eventpoll_init+0x0/0x85 returned 0 after 0 msecs
calling anon_inode_init+0x0/0x115
initcall anon_inode_init+0x0/0x115 returned 0 after 0 msecs
calling acpi_rtc_init+0x0/0xf4
initcall acpi_rtc_init+0x0/0xf4 returned 0 after 0 msecs
calling acpi_event_init+0x0/0x80
initcall acpi_event_init+0x0/0x80 returned 0 after 13 msecs
calling pnp_system_init+0x0/0x12
system 00:01: ioport range 0x408-0x40f has been reserved
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x700-0x73f has been reserved
system 00:01: ioport range 0x800-0x8fe has been reserved
system 00:01: ioport range 0x900-0x9fe has been reserved
system 00:01: ioport range 0x9ff-0x9ff has been reserved
system 00:01: ioport range 0xa00-0xafe has been reserved
system 00:01: ioport range 0xaff-0xaff has been reserved
system 00:01: ioport range 0xb00-0xbfe has been reserved
system 00:01: ioport range 0xbff-0xbff has been reserved
system 00:01: ioport range 0xc80-0xc83 has been reserved
system 00:01: ioport range 0xcd4-0xcd7 has been reserved
system 00:01: ioport range 0xf50-0xf58 has been reserved
system 00:01: ioport range 0xca0-0xca1 has been reserved
system 00:01: ioport range 0xca4-0xca5 has been reserved
system 00:01: ioport range 0xcf9-0xcf9 could not be reserved
system 00:01: ioport range 0x3f8-0x3ff has been reserved
system 00:01: iomem range 0x80000000-0x8fffffff could not be reserved
system 00:01: iomem range 0xf7df0000-0xf7df0fff has been reserved
system 00:01: iomem range 0xfdef0000-0xfdef0fff has been reserved
initcall pnp_system_init+0x0/0x12 returned 0 after 8 msecs
calling chr_dev_init+0x0/0xa1
initcall chr_dev_init+0x0/0xa1 returned 0 after 0 msecs
calling firmware_class_init+0x0/0x79
initcall firmware_class_init+0x0/0x79 returned 0 after 0 msecs
calling loopback_init+0x0/0x12
initcall loopback_init+0x0/0x12 returned 0 after 0 msecs
calling cpufreq_gov_performance_init+0x0/0x12
initcall cpufreq_gov_performance_init+0x0/0x12 returned 0 after 0 msecs
calling cpufreq_gov_userspace_init+0x0/0x12
initcall cpufreq_gov_userspace_init+0x0/0x12 returned 0 after 0 msecs
calling init_acpi_pm_clocksource+0x0/0xa4
initcall init_acpi_pm_clocksource+0x0/0xa4 returned 0 after 0 msecs
calling ssb_modinit+0x0/0x4a
initcall ssb_modinit+0x0/0x4a returned 0 after 0 msecs
calling pcibios_assign_resources+0x0/0x87
pci 0000:00:09.0: PCI bridge, secondary bus 0000:01

pci 0000:00:09.0:   IO window: 0x1000-0x2fff
pci 0000:00:09.0:   MEM window: 0xf7e00000-0xf7ffffff
pci 0000:00:09.0:   PREFETCH window: 0x000000e8000000-0x000000efffffff
pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
pci 0000:02:00.0:   IO window: disabled
pci 0000:02:00.0:   MEM window: 0xf8000000-0xf9ffffff
pci 0000:02:00.0:   PREFETCH window: 0x00000090000000-0x000000900fffff
pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02
pci 0000:00:0b.0:   IO window: disabled
pci 0000:00:0b.0:   MEM window: 0xf8000000-0xf9ffffff
pci 0000:00:0b.0:   PREFETCH window: 0x00000090000000-0x000000900fffff
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0:   IO window: disabled
pci 0000:04:00.0:   MEM window: 0xfa000000-0xfbffffff
pci 0000:04:00.0:   PREFETCH window: 0x00000090100000-0x000000901fffff
pci 0000:00:0c.0: PCI bridge, secondary bus 0000:04
pci 0000:00:0c.0:   IO window: disabled
pci 0000:00:0c.0:   MEM window: 0xfa000000-0xfbffffff
pci 0000:00:0c.0:   PREFETCH window: 0x00000090100000-0x000000901fffff
pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
pci 0000:06:00.0:   IO window: disabled
pci 0000:06:00.0:   MEM window: 0xfdc00000-0xfdcfffff
pci 0000:06:00.0:   PREFETCH window: 0x00000090200000-0x000000902fffff
pci 0000:00:0d.0: PCI bridge, secondary bus 0000:06
pci 0000:00:0d.0:   IO window: disabled
pci 0000:00:0d.0:   MEM window: 0xfdc00000-0xfdcfffff
pci 0000:00:0d.0:   PREFETCH window: 0x00000090200000-0x000000902fffff
pci 0000:00:0e.0: PCI bridge, secondary bus 0000:08
pci 0000:00:0e.0:   IO window: 0x3000-0x3fff
pci 0000:00:0e.0:   MEM window: 0xfdd00000-0xfddfffff
pci 0000:00:0e.0:   PREFETCH window: 0x00000090300000-0x000000903fffff

pci 0000:00:09.0: setting latency timer to 64 pci 0000:00:0b.0: setting latency timer to 64 pci 0000:02:00.0: setting latency timer to 64 pci 0000:00:0c.0: setting latency timer to 64 pci 0000:04:00.0: setting latency timer to 64 pci 0000:00:0d.0: setting latency timer to 64 pci 0000:06:00.0: setting latency timer to 64 pci 0000:00:0e.0: setting latency timer to 64 pci 0000:42:04.0: PCI bridge, secondary bus 0000:43

pci 0000:42:04.0:   IO window: disabled
pci 0000:42:04.0:   MEM window: disabled
pci 0000:42:04.0:   PREFETCH window: disabled
pci 0000:41:00.0: PCI bridge, secondary bus 0000:42
pci 0000:41:00.0:   IO window: 0x4000-0x4fff
pci 0000:41:00.0:   MEM window: 0xfdf00000-0xfdffffff
pci 0000:41:00.0:   PREFETCH window: 0x00000084000000-0x000000840fffff
pci 0000:40:0c.0: PCI bridge, secondary bus 0000:41
pci 0000:40:0c.0:   IO window: 0x4000-0x4fff
pci 0000:40:0c.0:   MEM window: 0xfdf00000-0xfdffffff
pci 0000:40:0c.0:   PREFETCH window: 0x00000084000000-0x000000840fffff
pci 0000:40:0d.0: PCI bridge, secondary bus 0000:44
pci 0000:40:0d.0:   IO window: disabled
pci 0000:40:0d.0:   MEM window: disabled
pci 0000:40:0d.0:   PREFETCH window: disabled
pci 0000:40:0e.0: PCI bridge, secondary bus 0000:47
pci 0000:40:0e.0:   IO window: disabled
pci 0000:40:0e.0:   MEM window: disabled
pci 0000:40:0e.0:   PREFETCH window: disabled

pci 0000:40:0c.0: setting latency timer to 64
pci 0000:41:00.0: setting latency timer to 64
pci 0000:40:0d.0: setting latency timer to 64
pci 0000:40:0e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, 3fff]
bus: 00 index 1 mmio: [90000000, fddfffff]
bus: 00 index 2 mmio: [80000000, 83ffffff]
bus: 00 index 3 mmio: [a0000, bffff]
bus: 00 index 4 mmio: [fe000000, ffffffff]
bus: 00 index 5 mmio: [280000000, fcffffffff]
bus: 01 index 0 io port: [1000, 2fff]
bus: 01 index 1 mmio: [f7e00000, f7ffffff]
bus: 01 index 2 mmio: [e8000000, efffffff]
bus: 01 index 3 io port: [0, 3fff]
bus: 01 index 4 mmio: [90000000, fddfffff]
bus: 01 index 5 mmio: [80000000, 83ffffff]
bus: 01 index 6 mmio: [a0000, bffff]
bus: 01 index 7 mmio: [fe000000, ffffffff]
bus: 01 index 8 mmio: [280000000, fcffffffff]
bus: 02 index 0 mmio: [0, 0]
bus: 02 index 1 mmio: [f8000000, f9ffffff]
bus: 02 index 2 mmio: [90000000, 900fffff]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 mmio: [0, 0]
bus: 03 index 1 mmio: [f8000000, f9ffffff]
bus: 03 index 2 mmio: [90000000, 900fffff]
bus: 03 index 3 mmio: [0, 0]
bus: 04 index 0 mmio: [0, 0]
bus: 04 index 1 mmio: [fa000000, fbffffff]
bus: 04 index 2 mmio: [90100000, 901fffff]
bus: 04 index 3 mmio: [0, 0]
bus: 05 index 0 mmio: [0, 0]
bus: 05 index 1 mmio: [fa000000, fbffffff]
bus: 05 index 2 mmio: [90100000, 901fffff]
bus: 05 index 3 mmio: [0, 0]
bus: 06 index 0 mmio: [0, 0]
bus: 06 index 1 mmio: [fdc00000, fdcfffff]
bus: 06 index 2 mmio: [90200000, 902fffff]
bus: 06 index 3 mmio: [0, 0]
bus: 07 index 0 mmio: [0, 0]
bus: 07 index 1 mmio: [fdc00000, fdcfffff]
bus: 07 index 2 mmio: [90200000, 902fffff]
bus: 07 index 3 mmio: [0, 0]
bus: 08 index 0 io port: [3000, 3fff]
bus: 08 index 1 mmio: [fdd00000, fddfffff]
bus: 08 index 2 mmio: [90300000, 903fffff]
bus: 08 index 3 mmio: [0, 0]
bus: 40 index 0 io port: [4000, ffff]
bus: 40 index 1 mmio: [fde00000, fdffffff]
bus: 40 index 2 mmio: [84000000, 8fffffff]
bus: 41 index 0 io port: [4000, 4fff]
bus: 41 index 1 mmio: [fdf00000, fdffffff]
bus: 41 index 2 mmio: [84000000, 840fffff]
bus: 41 index 3 mmio: [0, 0]
bus: 42 index 0 io port: [4000, 4fff]
bus: 42 index 1 mmio: [fdf00000, fdffffff]
bus: 42 index 2 mmio: [84000000, 840fffff]
bus: 42 index 3 mmio: [0, 0]
bus: 43 index 0 mmio: [0, 0]
bus: 43 index 1 mmio: [0, 0]
bus: 43 index 2 mmio: [0, 0]
bus: 43 index 3 mmio: [0, 0]
bus: 44 index 0 mmio: [0, 0]
bus: 44 index 1 mmio: [0, 0]
bus: 44 index 2 mmio: [0, 0]
bus: 44 index 3 mmio: [0, 0]
bus: 47 index 0 mmio: [0, 0]
bus: 47 index 1 mmio: [0, 0]
bus: 47 index 2 mmio: [0, 0]
bus: 47 index 3 mmio: [0, 0]
initcall pcibios_assign_resources+0x0/0x87 returned 0 after 23 msecs
calling inet_init+0x0/0x204
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
initcall inet_init+0x0/0x204 returned 0 after 66 msecs
calling af_unix_init+0x0/0x55
NET: Registered protocol family 1
initcall af_unix_init+0x0/0x55 returned 0 after 0 msecs
calling populate_rootfs+0x0/0xea
checking if image is initramfs... it is
Freeing initrd memory: 1322k freed
initcall populate_rootfs+0x0/0xea returned 0 after 187 msecs
calling i8259A_init_sysfs+0x0/0x22
initcall i8259A_init_sysfs+0x0/0x22 returned 0 after 0 msecs
calling vsyscall_init+0x0/0x6c
initcall vsyscall_init+0x0/0x6c returned 0 after 0 msecs
calling sbf_init+0x0/0xd7
initcall sbf_init+0x0/0xd7 returned 0 after 0 msecs
calling i8237A_init_sysfs+0x0/0x22
initcall i8237A_init_sysfs+0x0/0x22 returned 0 after 0 msecs
calling add_rtc_cmos+0x0/0x1d
initcall add_rtc_cmos+0x0/0x1d returned 0 after 0 msecs
calling cache_sysfs_init+0x0/0x54
initcall cache_sysfs_init+0x0/0x54 returned 0 after 1 msecs
calling mce_init_device+0x0/0x75
initcall mce_init_device+0x0/0x75 returned 0 after 0 msecs
calling periodic_mcheck_init+0x0/0x3f
initcall periodic_mcheck_init+0x0/0x3f returned 0 after 0 msecs
calling thermal_throttle_init_device+0x0/0x7a
initcall thermal_throttle_init_device+0x0/0x7a returned 0 after 0 msecs
calling threshold_init_device+0x0/0x40
initcall threshold_init_device+0x0/0x40 returned 0 after 0 msecs
calling msr_init+0x0/0xe7
initcall msr_init+0x0/0xe7 returned 0 after 0 msecs
calling cpuid_init+0x0/0xe7
initcall cpuid_init+0x0/0xe7 returned 0 after 0 msecs
calling microcode_init+0x0/0xb9
IA-32 Microcode Update Driver: v1.14a <[email protected]>
microcode: CPU0 not a capable Intel processor
microcode: CPU1 not a capable Intel processor
microcode: CPU2 not a capable Intel processor
microcode: CPU3 not a capable Intel processor
initcall microcode_init+0x0/0xb9 returned 0 after 1 msecs
calling init_lapic_sysfs+0x0/0x2d
initcall init_lapic_sysfs+0x0/0x2d returned 0 after 0 msecs
calling ioapic_init_sysfs+0x0/0x99
initcall ioapic_init_sysfs+0x0/0x99 returned 0 after 0 msecs
calling add_pcspkr+0x0/0x43
initcall add_pcspkr+0x0/0x43 returned 0 after 0 msecs
calling uv_ptc_init+0x0/0x75
initcall uv_ptc_init+0x0/0x75 returned 0 after 0 msecs
calling uv_bau_init+0x0/0x5a0
initcall uv_bau_init+0x0/0x5a0 returned 0 after 0 msecs
calling audit_classes_init+0x0/0xaf
initcall audit_classes_init+0x0/0xaf returned 0 after 0 msecs
calling init_vdso_vars+0x0/0x1f2
initcall init_vdso_vars+0x0/0x1f2 returned 0 after 0 msecs
calling ia32_binfmt_init+0x0/0x14
initcall ia32_binfmt_init+0x0/0x14 returned 0 after 0 msecs
calling sysenter_setup+0x0/0x2cc
initcall sysenter_setup+0x0/0x2cc returned 0 after 0 msecs
calling init_aout_binfmt+0x0/0x12
initcall init_aout_binfmt+0x0/0x12 returned 0 after 0 msecs
calling ioresources_init+0x0/0x3c
initcall ioresources_init+0x0/0x3c returned 0 after 0 msecs
calling uid_cache_init+0x0/0x69
initcall uid_cache_init+0x0/0x69 returned 0 after 0 msecs
calling init_posix_timers+0x0/0xb6
initcall init_posix_timers+0x0/0xb6 returned 0 after 0 msecs
calling init_posix_cpu_timers+0x0/0xd4
initcall init_posix_cpu_timers+0x0/0xd4 returned 0 after 0 msecs
calling nsproxy_cache_init+0x0/0x2d
initcall nsproxy_cache_init+0x0/0x2d returned 0 after 0 msecs
calling create_proc_profile+0x0/0x2bb
initcall create_proc_profile+0x0/0x2bb returned 0 after 0 msecs
calling timekeeping_init_device+0x0/0x22
initcall timekeeping_init_device+0x0/0x22 returned 0 after 0 msecs
calling init_clocksource_sysfs+0x0/0x50
initcall init_clocksource_sysfs+0x0/0x50 returned 0 after 0 msecs
calling init_timer_list_procfs+0x0/0x2c
initcall init_timer_list_procfs+0x0/0x2c returned 0 after 0 msecs
calling init_tstats_procfs+0x0/0x2c
initcall init_tstats_procfs+0x0/0x2c returned 0 after 0 msecs
calling futex_init+0x0/0x63
initcall futex_init+0x0/0x63 returned 0 after 0 msecs
calling proc_dma_init+0x0/0x22
initcall proc_dma_init+0x0/0x22 returned 0 after 0 msecs
calling percpu_modinit+0x0/0x6f
initcall percpu_modinit+0x0/0x6f returned 0 after 0 msecs
calling kallsyms_init+0x0/0x25
initcall kallsyms_init+0x0/0x25 returned 0 after 0 msecs
calling snapshot_device_init+0x0/0x12
initcall snapshot_device_init+0x0/0x12 returned 0 after 0 msecs
calling crash_save_vmcoreinfo_init+0x0/0x42b
initcall crash_save_vmcoreinfo_init+0x0/0x42b returned 0 after 0 msecs
calling crash_notes_memory_init+0x0/0x3d
initcall crash_notes_memory_init+0x0/0x3d returned 0 after 0 msecs
calling ikconfig_init+0x0/0x39
initcall ikconfig_init+0x0/0x39 returned 0 after 0 msecs
calling audit_init+0x0/0x14d
audit: initializing netlink socket (disabled)
type=2000 audit(1219250820.851:1): initialized
initcall audit_init+0x0/0x14d returned 0 after 0 msecs
calling audit_tree_init+0x0/0x49
initcall audit_tree_init+0x0/0x49 returned 0 after 0 msecs
calling init_kprobes+0x0/0x127
initcall init_kprobes+0x0/0x127 returned 0 after 5 msecs
calling utsname_sysctl_init+0x0/0x14
initcall utsname_sysctl_init+0x0/0x14 returned 0 after 0 msecs
calling init_per_zone_pages_min+0x0/0x53
initcall init_per_zone_pages_min+0x0/0x53 returned 0 after 0 msecs
calling pdflush_init+0x0/0x1d
initcall pdflush_init+0x0/0x1d returned 0 after 0 msecs
calling kswapd_init+0x0/0x64
initcall kswapd_init+0x0/0x64 returned 0 after 0 msecs
calling setup_vmstat+0x0/0x41
initcall setup_vmstat+0x0/0x41 returned 0 after 0 msecs
calling mm_sysfs_init+0x0/0x29
initcall mm_sysfs_init+0x0/0x29 returned 0 after 0 msecs
calling procswaps_init+0x0/0x22
initcall procswaps_init+0x0/0x22 returned 0 after 0 msecs
calling hugetlb_init+0x0/0x2ba
HugeTLB registered 2 MB page size, pre-allocated 0 pages
initcall hugetlb_init+0x0/0x2ba returned 0 after 0 msecs
calling init_tmpfs+0x0/0xda
initcall init_tmpfs+0x0/0xda returned 0 after 0 msecs
calling slab_sysfs_init+0x0/0xf0
initcall slab_sysfs_init+0x0/0xf0 returned 0 after 5 msecs
calling fasync_init+0x0/0x2a
initcall fasync_init+0x0/0x2a returned 0 after 0 msecs
calling aio_setup+0x0/0x6e
initcall aio_setup+0x0/0x6e returned 0 after 0 msecs
calling inotify_setup+0x0/0x12
initcall inotify_setup+0x0/0x12 returned 0 after 0 msecs
calling inotify_user_setup+0x0/0xb8
initcall inotify_user_setup+0x0/0xb8 returned 0 after 0 msecs
calling init_sys32_ioctl+0x0/0x85
initcall init_sys32_ioctl+0x0/0x85 returned 0 after 0 msecs
calling init_mbcache+0x0/0x14
initcall init_mbcache+0x0/0x14 returned 0 after 0 msecs
calling dnotify_init+0x0/0x2a
initcall dnotify_init+0x0/0x2a returned 0 after 0 msecs
calling vmcore_init+0x0/0x894
initcall vmcore_init+0x0/0x894 returned 0 after 0 msecs
calling configfs_init+0x0/0xb3
initcall configfs_init+0x0/0xb3 returned 0 after 0 msecs
calling init_devpts_fs+0x0/0x3f
initcall init_devpts_fs+0x0/0x3f returned 0 after 0 msecs
calling init_ext3_fs+0x0/0x6a
initcall init_ext3_fs+0x0/0x6a returned 0 after 0 msecs
calling journal_init+0x0/0x99
initcall journal_init+0x0/0x99 returned 0 after 0 msecs
calling init_ext2_fs+0x0/0x6a
initcall init_ext2_fs+0x0/0x6a returned 0 after 0 msecs
calling init_ramfs_fs+0x0/0x12
initcall init_ramfs_fs+0x0/0x12 returned 0 after 0 msecs
calling init_hugetlbfs_fs+0x0/0x98
initcall init_hugetlbfs_fs+0x0/0x98 returned 0 after 0 msecs
calling init_fat_fs+0x0/0x4f
initcall init_fat_fs+0x0/0x4f returned 0 after 0 msecs
calling init_msdos_fs+0x0/0x12
initcall init_msdos_fs+0x0/0x12 returned 0 after 0 msecs
calling init_vfat_fs+0x0/0x12
initcall init_vfat_fs+0x0/0x12 returned 0 after 0 msecs
calling init_iso9660_fs+0x0/0x6c
initcall init_iso9660_fs+0x0/0x6c returned 0 after 0 msecs
calling init_nfs_fs+0x0/0x10e
initcall init_nfs_fs+0x0/0x10e returned 0 after 0 msecs
calling init_nfsd+0x0/0xbb
Installing knfsd (copyright (C) 1996 [email protected]).
initcall init_nfsd+0x0/0xbb returned 0 after 0 msecs
calling init_nlm+0x0/0x22
initcall init_nlm+0x0/0x22 returned 0 after 0 msecs
calling init_nls_cp437+0x0/0x12
initcall init_nls_cp437+0x0/0x12 returned 0 after 0 msecs
calling init_nls_cp850+0x0/0x12
initcall init_nls_cp850+0x0/0x12 returned 0 after 0 msecs
calling init_nls_ascii+0x0/0x12
initcall init_nls_ascii+0x0/0x12 returned 0 after 0 msecs
calling init_nls_iso8859_1+0x0/0x12
initcall init_nls_iso8859_1+0x0/0x12 returned 0 after 0 msecs
calling init_nls_iso8859_15+0x0/0x12
initcall init_nls_iso8859_15+0x0/0x12 returned 0 after 0 msecs
calling init_nls_utf8+0x0/0x25
initcall init_nls_utf8+0x0/0x25 returned 0 after 0 msecs
calling ipc_init+0x0/0x23
msgmni has been set to 16013
initcall ipc_init+0x0/0x23 returned 0 after 0 msecs
calling ipc_sysctl_init+0x0/0x14
initcall ipc_sysctl_init+0x0/0x14 returned 0 after 0 msecs
calling init_mqueue_fs+0x0/0xc6
initcall init_mqueue_fs+0x0/0xc6 returned 0 after 0 msecs
calling crypto_algapi_init+0x0/0xd
initcall crypto_algapi_init+0x0/0xd returned 0 after 0 msecs
calling blkcipher_module_init+0x0/0x2a
initcall blkcipher_module_init+0x0/0x2a returned 0 after 0 msecs
calling cryptomgr_init+0x0/0x12
initcall cryptomgr_init+0x0/0x12 returned 0 after 0 msecs
calling hmac_module_init+0x0/0x12
initcall hmac_module_init+0x0/0x12 returned 0 after 0 msecs
calling md5_mod_init+0x0/0x12
initcall md5_mod_init+0x0/0x12 returned 0 after 0 msecs
calling sha1_generic_mod_init+0x0/0x12
initcall sha1_generic_mod_init+0x0/0x12 returned 0 after 0 msecs
calling crypto_cbc_module_init+0x0/0x12
initcall crypto_cbc_module_init+0x0/0x12 returned 0 after 0 msecs
calling des_generic_mod_init+0x0/0x3f
initcall des_generic_mod_init+0x0/0x3f returned 0 after 0 msecs
calling cast5_mod_init+0x0/0x12
initcall cast5_mod_init+0x0/0x12 returned 0 after 0 msecs
calling deflate_mod_init+0x0/0x12
initcall deflate_mod_init+0x0/0x12 returned 0 after 0 msecs
calling crc32c_mod_init+0x0/0x3f
initcall crc32c_mod_init+0x0/0x3f returned 0 after 0 msecs
calling crypto_authenc_module_init+0x0/0x12
initcall crypto_authenc_module_init+0x0/0x12 returned 0 after 0 msecs
calling bsg_init+0x0/0x126
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
initcall bsg_init+0x0/0x126 returned 0 after 0 msecs
calling noop_init+0x0/0x14
io scheduler noop registered
initcall noop_init+0x0/0x14 returned 0 after 0 msecs
calling as_init+0x0/0x14
io scheduler anticipatory registered
initcall as_init+0x0/0x14 returned 0 after 0 msecs
calling deadline_init+0x0/0x14
io scheduler deadline registered
initcall deadline_init+0x0/0x14 returned 0 after 0 msecs
calling cfq_init+0x0/0x9d
io scheduler cfq registered (default)
initcall cfq_init+0x0/0x9d returned 0 after 0 msecs
calling percpu_counter_startup+0x0/0x14
initcall percpu_counter_startup+0x0/0x14 returned 0 after 0 msecs
calling pci_init+0x0/0x35
pci 0000:00:00.0: Enabling HT MSI Mapping
pci 0000:00:0b.0: Enabling HT MSI Mapping
pci 0000:00:0b.0: Found enabled HT MSI Mapping
pci 0000:00:0c.0: Enabling HT MSI Mapping
pci 0000:00:0c.0: Found enabled HT MSI Mapping
pci 0000:00:0d.0: Enabling HT MSI Mapping
pci 0000:00:0d.0: Found enabled HT MSI Mapping
pci 0000:00:0e.0: Enabling HT MSI Mapping
pci 0000:00:0e.0: Found enabled HT MSI Mapping
pci 0000:01:03.0: Boot video device
pci 0000:01:04.4: HCRESET not completed yet!
pci 0000:40:00.0: Enabling HT MSI Mapping
pci 0000:40:0c.0: Enabling HT MSI Mapping
pci 0000:40:0c.0: Found enabled HT MSI Mapping
pci 0000:40:0d.0: Enabling HT MSI Mapping
pci 0000:40:0d.0: Found enabled HT MSI Mapping
pci 0000:40:0e.0: Enabling HT MSI Mapping
pci 0000:40:0e.0: Found enabled HT MSI Mapping
initcall pci_init+0x0/0x35 returned 0 after 3 msecs
calling pci_proc_init+0x0/0x6a
initcall pci_proc_init+0x0/0x6a returned 0 after 0 msecs
calling pcie_portdrv_init+0x0/0x4c
pcieport-driver 0000:00:0b.0: setting latency timer to 64
pcieport-driver 0000:00:0b.0: found MSI capability
pci_express 0000:00:0b.0:pcie00: allocate port service
pci_express 0000:00:0b.0:pcie01: allocate port service
pci_express 0000:00:0b.0:pcie03: allocate port service
pcieport-driver 0000:00:0c.0: setting latency timer to 64
pcieport-driver 0000:00:0c.0: found MSI capability
pci_express 0000:00:0c.0:pcie00: allocate port service
pci_express 0000:00:0c.0:pcie01: allocate port service
pci_express 0000:00:0c.0:pcie03: allocate port service
pcieport-driver 0000:00:0d.0: setting latency timer to 64
pcieport-driver 0000:00:0d.0: found MSI capability
pci_express 0000:00:0d.0:pcie00: allocate port service
pci_express 0000:00:0d.0:pcie01: allocate port service
pci_express 0000:00:0d.0:pcie03: allocate port service
pcieport-driver 0000:00:0e.0: setting latency timer to 64
pcieport-driver 0000:00:0e.0: found MSI capability
pci_express 0000:00:0e.0:pcie00: allocate port service
pci_express 0000:00:0e.0:pcie01: allocate port service
pci_express 0000:00:0e.0:pcie03: allocate port service
pcieport-driver 0000:40:0c.0: setting latency timer to 64
pcieport-driver 0000:40:0c.0: found MSI capability
pci_express 0000:40:0c.0:pcie00: allocate port service
pci_express 0000:40:0c.0:pcie01: allocate port service
pci_express 0000:40:0c.0:pcie03: allocate port service
pcieport-driver 0000:40:0d.0: setting latency timer to 64
pcieport-driver 0000:40:0d.0: found MSI capability
pci_express 0000:40:0d.0:pcie00: allocate port service
pci_express 0000:40:0d.0:pcie01: allocate port service
pci_express 0000:40:0d.0:pcie03: allocate port service
pcieport-driver 0000:40:0e.0: setting latency timer to 64
pcieport-driver 0000:40:0e.0: found MSI capability
pci_express 0000:40:0e.0:pcie00: allocate port service
pci_express 0000:40:0e.0:pcie01: allocate port service
pci_express 0000:40:0e.0:pcie03: allocate port service
initcall pcie_portdrv_init+0x0/0x4c returned 0 after 9 msecs
calling fb_console_init+0x0/0x12b
initcall fb_console_init+0x0/0x12b returned 0 after 0 msecs
calling rivafb_init+0x0/0x1a5
initcall rivafb_init+0x0/0x1a5 returned 0 after 0 msecs
calling nvidiafb_init+0x0/0x2b6
initcall nvidiafb_init+0x0/0x2b6 returned 0 after 0 msecs
calling vt8623fb_init+0x0/0x5f
initcall vt8623fb_init+0x0/0x5f returned 0 after 0 msecs
calling vesafb_init+0x0/0x235
initcall vesafb_init+0x0/0x235 returned 0 after 0 msecs
calling acpi_reserve_resources+0x0/0xeb
initcall acpi_reserve_resources+0x0/0xeb returned 0 after 0 msecs
calling acpi_ac_init+0x0/0x45
initcall acpi_ac_init+0x0/0x45 returned 0 after 0 msecs
calling acpi_button_init+0x0/0x5e
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
initcall acpi_button_init+0x0/0x5e returned 0 after 0 msecs
calling acpi_fan_init+0x0/0x5e
initcall acpi_fan_init+0x0/0x5e returned 0 after 0 msecs
calling irqrouter_init_sysfs+0x0/0x38
initcall irqrouter_init_sysfs+0x0/0x38 returned 0 after 0 msecs
calling acpi_processor_init+0x0/0x10b
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
processor ACPI0007:02: registered as cooling_device2
processor ACPI0007:03: registered as cooling_device3
initcall acpi_processor_init+0x0/0x10b returned 0 after 1 msecs
calling acpi_container_init+0x0/0x42
initcall acpi_container_init+0x0/0x42 returned 0 after 1 msecs
calling acpi_thermal_init+0x0/0x83
initcall acpi_thermal_init+0x0/0x83 returned 0 after 0 msecs
calling rand_initialize+0x0/0x2c
initcall rand_initialize+0x0/0x2c returned 0 after 0 msecs
calling tty_init+0x0/0x1cd
initcall tty_init+0x0/0x1cd returned 0 after 22 msecs
calling pty_init+0x0/0x26f
initcall pty_init+0x0/0x26f returned 0 after 0 msecs
calling raw_init+0x0/0xdd
initcall raw_init+0x0/0xdd returned 0 after 0 msecs
calling hpet_init+0x0/0x6a
hpet_resources: 0xfed00000 is busy
initcall hpet_init+0x0/0x6a returned 0 after 0 msecs
calling nvram_init+0x0/0x8a
Non-volatile memory driver v1.2
initcall nvram_init+0x0/0x8a returned 0 after 0 msecs
calling mod_init+0x0/0x1f8
initcall mod_init+0x0/0x1f8 returned -19 after 0 msecs
calling mod_init+0x0/0xba
initcall mod_init+0x0/0xba returned -19 after 0 msecs
calling agp_init+0x0/0x26
Linux agpgart interface v0.103
initcall agp_init+0x0/0x26 returned 0 after 0 msecs
calling agp_intel_init+0x0/0x29
initcall agp_intel_init+0x0/0x29 returned 0 after 0 msecs
calling agp_via_init+0x0/0x29
initcall agp_via_init+0x0/0x29 returned 0 after 0 msecs
calling ipmi_init_msghandler_mod+0x0/0xd
ipmi message handler version 39.2
initcall ipmi_init_msghandler_mod+0x0/0xd returned 0 after 0 msecs
calling init_ipmi_devintf+0x0/0x101
ipmi device interface
initcall init_ipmi_devintf+0x0/0x101 returned 0 after 0 msecs
calling init_ipmi_si+0x0/0x78a
IPMI System Interface driver.
ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0
Clocksource tsc unstable (delta = 637358161795 ns)
ipmi: Found new BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11)
IPMI kcs interface initialized
ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
ipmi_si: duplicate interface
ACPI: PCI Interrupt Link [LNKW] enabled at IRQ 16
ipmi_si 0000:01:04.6: PCI INT A -> Link[LNKW] -> GSI 16 (level, high) -> IRQ 16
ipmi_si: Trying PCI-specified kcs state machine at mem address 0xf7ef0000, slave address 0x0, irq 16
Using irq 16
ipmi: interfacing existing BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11)
IPMI kcs interface initialized
initcall init_ipmi_si+0x0/0x78a returned 0 after 192 msecs
calling ipmi_wdog_init+0x0/0x12e
IPMI Watchdog: driver initialized
initcall ipmi_wdog_init+0x0/0x12e returned 0 after 6 msecs
calling ipmi_poweroff_init+0x0/0x8d
Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot.
IPMI poweroff: ATCA Detect mfg 0xB prod 0x0
IPMI poweroff: Unable to find a poweroff function that will work, giving up
IPMI poweroff: ATCA Detect mfg 0xB prod 0x0
IPMI poweroff: Unable to find a poweroff function that will work, giving up
initcall ipmi_poweroff_init+0x0/0x8d returned 0 after 44 msecs
calling hangcheck_init+0x0/0x8a
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
initcall hangcheck_init+0x0/0x8a returned 0 after 5 msecs
calling drm_core_init+0x0/0xf9
[drm] Initialized drm 1.1.0 20060810
initcall drm_core_init+0x0/0xf9 returned 0 after 0 msecs
calling r128_init+0x0/0x1e
initcall r128_init+0x0/0x1e returned 0 after 0 msecs
calling radeon_init+0x0/0x1e
ACPI: PCI Interrupt Link [LNKY] enabled at IRQ 18
pci 0000:01:03.0: PCI INT A -> Link[LNKY] -> GSI 18 (level, high) -> IRQ 18
[drm] Initialized radeon 1.29.0 20080528 on minor 0
initcall radeon_init+0x0/0x1e returned 0 after 2 msecs
calling via_init+0x0/0x23
initcall via_init+0x0/0x23 returned 0 after 0 msecs
calling cn_proc_init+0x0/0x3d
initcall cn_proc_init+0x0/0x3d returned 0 after 0 msecs
calling serial8250_init+0x0/0x131
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
initcall serial8250_init+0x0/0x131 returned 0 after 1 msecs
calling serial8250_pnp_init+0x0/0x12
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
initcall serial8250_pnp_init+0x0/0x12 returned 0 after 0 msecs
calling serial8250_pci_init+0x0/0x1b
initcall serial8250_pci_init+0x0/0x1b returned 0 after 0 msecs
calling topology_sysfs_init+0x0/0x40
initcall topology_sysfs_init+0x0/0x40 returned 0 after 0 msecs
calling floppy_init+0x0/0xf14
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
initcall floppy_init+0x0/0xf14 returned -19 after 2876 msecs
calling brd_init+0x0/0x167
brd: module loaded
initcall brd_init+0x0/0x167 returned 0 after 3 msecs
calling bnx2_init+0x0/0x1b
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.8.0 (Aug 14, 2008)
ACPI: PCI Interrupt Link [LNKX] enabled at IRQ 17
bnx2 0000:03:00.0: PCI INT A -> Link[LNKX] -> GSI 17 (level, high) -> IRQ 17
eth0: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 17, node addr 00:18:fe:35:26:f6 bnx2 0000:05:00.0: PCI INT A -> Link[LNKW] -> GSI 16 (level, high) -> IRQ 16
eth1: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit 133MHz found at mem fa000000, IRQ 16, node addr 00:18:fe:35:26:f4 initcall bnx2_init+0x0/0x1b returned 0 after 47 msecs
calling net_olddevs_init+0x0/0xa0
initcall net_olddevs_init+0x0/0xa0 returned 0 after 0 msecs
calling b44_init+0x0/0x63
initcall b44_init+0x0/0x63 returned 0 after 0 msecs
calling tun_init+0x0/0xa0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
initcall tun_init+0x0/0xa0 returned 0 after 0 msecs
calling init_netconsole+0x0/0x1bc
netconsole: local port 54883
netconsole: local IP 139.185.50.77
netconsole: interface eth0
netconsole: remote port 54883
netconsole: remote IP 139.185.50.76
netconsole: remote ethernet address 00:18:fe:34:1c:3d
netconsole: device eth0 not up yet, forcing it
bnx2: eth0: using MSI
netconsole: carrier detect appears untrustworthy, waiting 4 seconds
bnx2: eth0 NIC SerDes Link is Up, 1000 Mbps full duplex
console [netcon0] enabled
netconsole: network logging started
initcall init_netconsole+0x0/0x1bc returned 0 after 4179 msecs
calling scsi_tgt_init+0x0/0x7f
initcall scsi_tgt_init+0x0/0x7f returned 0 after 0 msecs
calling raid_init+0x0/0x12
initcall raid_init+0x0/0x12 returned 0 after 0 msecs
calling spi_transport_init+0x0/0x2e
initcall spi_transport_init+0x0/0x2e returned 0 after 0 msecs
calling fc_transport_init+0x0/0x4c
initcall fc_transport_init+0x0/0x4c returned 0 after 0 msecs
calling iscsi_transport_init+0x0/0x148
Loading iSCSI transport class v2.0-870.
initcall iscsi_transport_init+0x0/0x148 returned 0 after 0 msecs
calling sas_transport_init+0x0/0xbb
initcall sas_transport_init+0x0/0xbb returned 0 after 0 msecs
calling sas_class_init+0x0/0x31
initcall sas_class_init+0x0/0x31 returned 0 after 0 msecs
calling init_sd+0x0/0x10a
Driver 'sd' needs updating - please use bus_type methods
initcall init_sd+0x0/0x10a returned 0 after 0 msecs
calling init_sg+0x0/0x15a
initcall init_sg+0x0/0x15a returned 0 after 0 msecs
calling mon_init+0x0/0x103
initcall mon_init+0x0/0x103 returned 0 after 0 msecs
calling i8042_init+0x0/0x3bd
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
initcall i8042_init+0x0/0x3bd returned 0 after 7 msecs
calling serport_init+0x0/0x34
initcall serport_init+0x0/0x34 returned 0 after 0 msecs
calling serio_raw_init+0x0/0x1b
initcall serio_raw_init+0x0/0x1b returned 0 after 0 msecs
calling mousedev_init+0x0/0x61
mice: PS/2 mouse device common for all mice
initcall mousedev_init+0x0/0x61 returned 0 after 0 msecs
calling evdev_init+0x0/0x12
initcall evdev_init+0x0/0x12 returned 0 after 13 msecs
calling atkbd_init+0x0/0x27
initcall atkbd_init+0x0/0x27 returned 0 after 0 msecs
calling psmouse_init+0x0/0x6d
initcall psmouse_init+0x0/0x6d returned 0 after 58 msecs
calling pcspkr_init+0x0/0x12
input: PC Speaker as /class/input/input1
initcall pcspkr_init+0x0/0x12 returned 0 after 31 msecs
calling uinput_init+0x0/0x12
initcall uinput_init+0x0/0x12 returned 0 after 0 msecs
calling cmos_init+0x0/0x30
initcall cmos_init+0x0/0x30 returned 0 after 0 msecs
calling i2c_dev_init+0x0/0xa6
i2c /dev entries driver
initcall i2c_dev_init+0x0/0xa6 returned 0 after 0 msecs
calling amd756_init+0x0/0x1b
initcall amd756_init+0x0/0x1b returned 0 after 0 msecs
calling i2c_amd8111_init+0x0/0x1b
initcall i2c_amd8111_init+0x0/0x1b returned 0 after 0 msecs
calling i2c_i801_init+0x0/0x1b
initcall i2c_i801_init+0x0/0x1b returned 0 after 0 msecs
calling nforce2_init+0x0/0x1b
initcall nforce2_init+0x0/0x1b returned 0 after 0 msecs
calling i2c_piix4_init+0x0/0x1b
initcall i2c_piix4_init+0x0/0x1b returned 0 after 0 msecs
calling i2c_vt586b_init+0x0/0x1b
initcall i2c_vt586b_init+0x0/0x1b returned 0 after 0 msecs
calling i2c_vt596_init+0x0/0x1b
initcall i2c_vt596_init+0x0/0x1b returned 0 after 0 msecs
calling coretemp_init+0x0/0x15b
initcall coretemp_init+0x0/0x15b returned -19 after 0 msecs
calling k8temp_init+0x0/0x1b
initcall k8temp_init+0x0/0x1b returned 0 after 0 msecs
calling sm_via686a_init+0x0/0x1b
initcall sm_via686a_init+0x0/0x1b returned 0 after 0 msecs
calling vt1211_init+0x0/0x14e
initcall vt1211_init+0x0/0x14e returned -19 after 0 msecs
calling sm_vt8231_init+0x0/0x1b
initcall sm_vt8231_init+0x0/0x1b returned 0 after 0 msecs
calling watchdog_init+0x0/0xb4
SoftDog: cannot register miscdev on minor=130 (err=-16)
initcall watchdog_init+0x0/0xb4 returned -16 after 0 msecs
initcall watchdog_init+0x0/0xb4 returned with error code -16
calling edac_init+0x0/0x9d
EDAC MC: Ver: 2.1.0 Aug 20 2008
initcall edac_init+0x0/0x9d returned 0 after 0 msecs
calling i5000_init+0x0/0x41
initcall i5000_init+0x0/0x41 returned 0 after 0 msecs
calling e752x_init+0x0/0x41
initcall e752x_init+0x0/0x41 returned 0 after 0 msecs
calling i82975x_init+0x0/0xa0
initcall i82975x_init+0x0/0xa0 returned -19 after 0 msecs
calling cpufreq_stats_init+0x0/0x86
initcall cpufreq_stats_init+0x0/0x86 returned 0 after 0 msecs
calling cpufreq_gov_powersave_init+0x0/0x12
initcall cpufreq_gov_powersave_init+0x0/0x12 returned 0 after 0 msecs
calling cpufreq_gov_dbs_init+0x0/0x46
initcall cpufreq_gov_dbs_init+0x0/0x46 returned 0 after 0 msecs
calling cpufreq_gov_dbs_init+0x0/0x12
initcall cpufreq_gov_dbs_init+0x0/0x12 returned 0 after 0 msecs
calling init_ladder+0x0/0x12
cpuidle: using governor ladder
initcall init_ladder+0x0/0x12 returned 0 after 0 msecs
calling hid_init+0x0/0x8
initcall hid_init+0x0/0x8 returned 0 after 0 msecs
calling hid_init+0x0/0x61
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
initcall hid_init+0x0/0x61 returned 0 after 0 msecs
calling sysctl_core_init+0x0/0x25
initcall sysctl_core_init+0x0/0x25 returned 0 after 0 msecs
calling flow_cache_init+0x0/0x1b3
initcall flow_cache_init+0x0/0x1b3 returned 0 after 0 msecs
calling sysctl_ipv4_init+0x0/0x4e
initcall sysctl_ipv4_init+0x0/0x4e returned 0 after 0 msecs
calling ipip_init+0x0/0x71
IPv4 over IPv4 tunneling driver
initcall ipip_init+0x0/0x71 returned 0 after 0 msecs
calling ipgre_init+0x0/0x71
GRE over IPv4 tunneling driver
initcall ipgre_init+0x0/0x71 returned 0 after 0 msecs
calling init_syncookies+0x0/0x19
initcall init_syncookies+0x0/0x19 returned 0 after 0 msecs
calling ah4_init+0x0/0x68
initcall ah4_init+0x0/0x68 returned 0 after 0 msecs
calling esp4_init+0x0/0x68
initcall esp4_init+0x0/0x68 returned 0 after 0 msecs
calling ipcomp4_init+0x0/0x68
initcall ipcomp4_init+0x0/0x68 returned 0 after 0 msecs
calling ipip_init+0x0/0x68
initcall ipip_init+0x0/0x68 returned 0 after 0 msecs
calling xfrm4_beet_init+0x0/0x17
initcall xfrm4_beet_init+0x0/0x17 returned 0 after 0 msecs
calling tunnel4_init+0x0/0x32
initcall tunnel4_init+0x0/0x32 returned 0 after 0 msecs
calling xfrm4_transport_init+0x0/0x17
initcall xfrm4_transport_init+0x0/0x17 returned 0 after 0 msecs
calling xfrm4_mode_tunnel_init+0x0/0x17
initcall xfrm4_mode_tunnel_init+0x0/0x17 returned 0 after 0 msecs
calling inet_diag_init+0x0/0x69
initcall inet_diag_init+0x0/0x69 returned 0 after 0 msecs
calling tcp_diag_init+0x0/0x12
initcall tcp_diag_init+0x0/0x12 returned 0 after 0 msecs
calling bictcp_register+0x0/0x12
TCP bic registered
initcall bictcp_register+0x0/0x12 returned 0 after 0 msecs
calling xfrm_user_init+0x0/0x58
Initializing XFRM netlink socket
initcall xfrm_user_init+0x0/0x58 returned 0 after 0 msecs
calling packet_init+0x0/0x47
NET: Registered protocol family 17
initcall packet_init+0x0/0x47 returned 0 after 0 msecs
calling ipsec_pfkey_init+0x0/0x8c
NET: Registered protocol family 15
initcall ipsec_pfkey_init+0x0/0x8c returned 0 after 0 msecs
calling init_sunrpc+0x0/0x5d
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
initcall init_sunrpc+0x0/0x5d returned 0 after 0 msecs
calling init_rpcsec_gss+0x0/0x38
initcall init_rpcsec_gss+0x0/0x38 returned 0 after 0 msecs
calling init_kerberos_module+0x0/0x2f
initcall init_kerberos_module+0x0/0x2f returned 0 after 0 msecs
calling init_spkm3_module+0x0/0x2f
initcall init_spkm3_module+0x0/0x2f returned 0 after 0 msecs
calling powernowk8_init+0x0/0x84

powernow-k8: Found 2 Dual-Core AMD Opteron(tm) Processor 8218 processors (4 cpu cores) (version 2.20.00)
powernow-k8:    0 : fid 0x12 (2600 MHz), vid 0x8
powernow-k8:    1 : fid 0x10 (2400 MHz), vid 0xa
powernow-k8:    2 : fid 0xe (2200 MHz), vid 0xc
powernow-k8:    3 : fid 0xc (2000 MHz), vid 0xe
powernow-k8:    4 : fid 0xa (1800 MHz), vid 0x10
powernow-k8:    5 : fid 0x2 (1000 MHz), vid 0x12
powernow-k8:    0 : fid 0x12 (2600 MHz), vid 0x8
powernow-k8:    1 : fid 0x10 (2400 MHz), vid 0xa
powernow-k8:    2 : fid 0xe (2200 MHz), vid 0xc
powernow-k8:    3 : fid 0xc (2000 MHz), vid 0xe
powernow-k8:    4 : fid 0xa (1800 MHz), vid 0x10
powernow-k8:    5 : fid 0x2 (1000 MHz), vid 0x12

initcall powernowk8_init+0x0/0x84 returned 0 after 3 msecs
calling acpi_cpufreq_init+0x0/0x8f
initcall acpi_cpufreq_init+0x0/0x8f returned -16 after 0 msecs initcall acpi_cpufreq_init+0x0/0x8f returned with error code -16 calling centrino_init+0x0/0x36
initcall centrino_init+0x0/0x36 returned -19 after 0 msecs
calling cpufreq_p4_init+0x0/0x63
initcall cpufreq_p4_init+0x0/0x63 returned -19 after 0 msecs calling hpet_insert_resource+0x0/0x23
initcall hpet_insert_resource+0x0/0x23 returned 0 after 0 msecs calling update_mp_table+0x0/0x492
initcall update_mp_table+0x0/0x492 returned 0 after 0 msecs
calling lapic_insert_resource+0x0/0x40
initcall lapic_insert_resource+0x0/0x40 returned 0 after 0 msecs calling init_lapic_nmi_sysfs+0x0/0x38
initcall init_lapic_nmi_sysfs+0x0/0x38 returned 0 after 0 msecs calling ioapic_insert_resources+0x0/0x4f
initcall ioapic_insert_resources+0x0/0x4f returned 0 after 0 msecs calling check_early_ioremap_leak+0x0/0x42
initcall check_early_ioremap_leak+0x0/0x42 returned 0 after 0 msecs calling pat_memtype_list_init+0x0/0x29
initcall pat_memtype_list_init+0x0/0x29 returned 0 after 0 msecs calling init_oops_id+0x0/0x23
initcall init_oops_id+0x0/0x23 returned 0 after 0 msecs
calling disable_boot_consoles+0x0/0x3a
initcall disable_boot_consoles+0x0/0x3a returned 0 after 0 msecs calling pm_qos_power_init+0x0/0x61
initcall pm_qos_power_init+0x0/0x61 returned 0 after 0 msecs calling software_resume+0x0/0x13f
initcall software_resume+0x0/0x13f returned -2 after 0 msecs initcall software_resume+0x0/0x13f returned with error code -2 calling debugfs_kprobe_init+0x0/0x89
initcall debugfs_kprobe_init+0x0/0x89 returned 0 after 0 msecs calling taskstats_init+0x0/0x95
registered taskstats version 1
initcall taskstats_init+0x0/0x95 returned 0 after 0 msecs
calling random32_reseed+0x0/0x8d
initcall random32_reseed+0x0/0x8d returned 0 after 0 msecs
calling pci_sysfs_init+0x0/0x4c
initcall pci_sysfs_init+0x0/0x4c returned 0 after 0 msecs
calling acpi_wakeup_device_init+0x0/0xa5
initcall acpi_wakeup_device_init+0x0/0xa5 returned 0 after 0 msecs calling acpi_sleep_proc_init+0x0/0x55
initcall acpi_sleep_proc_init+0x0/0x55 returned 0 after 0 msecs calling seqgen_init+0x0/0xf
initcall seqgen_init+0x0/0xf returned 0 after 0 msecs
calling scsi_complete_async_scans+0x0/0xe5
initcall scsi_complete_async_scans+0x0/0xe5 returned 0 after 0 msecs calling rtc_hctosys+0x0/0x17b
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
initcall rtc_hctosys+0x0/0x17b returned -19 after 0 msecs
calling edd_init+0x0/0x2f1
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
initcall edd_init+0x0/0x2f1 returned -19 after 0 msecs
calling memmap_init+0x0/0xa3
initcall memmap_init+0x0/0xa3 returned 0 after 0 msecs
calling pci_mmcfg_late_insert_resources+0x0/0x43
initcall pci_mmcfg_late_insert_resources+0x0/0x43 returned 0 after 0 msecs calling tcp_congestion_default+0x0/0x12
initcall tcp_congestion_default+0x0/0x12 returned 0 after 0 msecs Freeing unused kernel memory: 396k freed
Write protecting the kernel read-only data: 4632k
calling uhci_hcd_init+0x0/0xb2 [uhci_hcd]
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:01:04.4: PCI INT B -> Link[LNKX] -> GSI 17 (level, high) -> IRQ 17 uhci_hcd 0000:01:04.4: UHCI Host Controller
uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 1 uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports uhci_hcd 0000:01:04.4: HCRESET not completed yet!
uhci_hcd 0000:01:04.4: irq 17, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
initcall uhci_hcd_init+0x0/0xb2 [uhci_hcd] returned 0 after 198 msecs insmod used greatest stack depth: 4976 bytes left
calling ohci_hcd_mod_init+0x0/0x45 [ohci_hcd]
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LNU0] enabled at IRQ 22
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LNU0] -> GSI 22 (level, high) -> IRQ 22 ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 22, io mem 0xf7de0000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2 initcall ohci_hcd_mod_init+0x0/0x45 [ohci_hcd] returned 0 after 151 msecs calling ehci_hcd_init+0x0/0x20 [ehci_hcd]
ACPI: PCI Interrupt Link [LNU2] enabled at IRQ 23
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LNU2] -> GSI 23 (level, high) -> IRQ 23 ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported ehci_hcd 0000:00:02.1: irq 23, io mem 0xf7dd0000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 10 ports detected
usb 1-1: configuration #1 chosen from 1 choice
input: HP Virtual Keyboard as /class/input/input2
input: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1
input: HP Virtual Keyboard as /class/input/input3
input: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1 initcall ehci_hcd_init+0x0/0x20 [ehci_hcd] returned 0 after 162 msecs calling cciss_init+0x0/0x2e [cciss]
HP CISS Driver (v 3.6.20)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 54
cciss 0000:42:08.0: PCI INT A -> Link[LNKA] -> GSI 54 (level, high) -> IRQ 54
cciss0: <0x3238> at PCI 0000:42:08.0 IRQ 503 using DAC

BUG: unable to handle kernel NULL pointer dereference at 0000000000000248
IP: [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]
PGD 17e422067 PUD 17e423067 PMD 0 
Oops: 0002 [1] SMP 
CPU 2 
Modules linked in: cciss(+) ehci_hcd ohci_hcd uhci_hcd
Pid: 0, comm: swapper Not tainted 2.6.27-rc3-git7 #1
RIP: 0010:[<ffffffffa001bb68>]  [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]
RSP: 0018:ffff88027f66fee8  EFLAGS: 00010007
RAX: 0000000000000000 RBX: ffff88007f840270 RCX: 000000000000000c
RDX: 0000000000000000 RSI: ffff88027e5c0000 RDI: ffff88027e5c0000
RBP: ffff88027f66ff18 R08: 0000000000000000 R09: ffff88017fa95e88
R10: 0000000000000000 R11: ffff88027f66ff48 R12: ffff88027e5c0000
R13: 0000000000000000 R14: 00000000000001f7 R15: 0000000000000086
FS:  0000000000680850(0000) GS:ffff88017fc02c80(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000248 CR3: 000000017e425000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff88017fa94000, task ffff88027f63d340)
Stack:  ffff88027f66fee0 ffff88017e9b4800 0000000000000000 0000000000000000
 00000000000001f7 0000000000000000 ffff88027f66ff48 ffffffff8026757e
 ffffffff80719000 00000000000001f7 ffff88017e9b4800 ffffffff80719050
Call Trace:
 <IRQ>  [<ffffffff8026757e>] handle_IRQ_event+0x27/0x57
 [<ffffffff80268d08>] handle_edge_irq+0xed/0x12e
 [<ffffffff8020eaab>] do_IRQ+0xf6/0x167
 [<ffffffff8020c471>] ret_from_intr+0x0/0xa
 <EOI>  [<ffffffff802122b1>] ? default_idle+0x2b/0x40
 [<ffffffff802124bf>] ? c1e_idle+0xd4/0xdb
 [<ffffffff8055677d>] ? atomic_notifier_call_chain+0xf/0x11
 [<ffffffff8020ac6c>] ? cpu_idle+0x71/0x8f
 [<ffffffff8054e752>] ? start_secondary+0x157/0x15c


Code: 8b 83 48 02 00 00 48 39 d8 74 37 49 39 9c 24 c0 00 01 00 75 08 49 89 84 24 c0 00 01 00 48 8b 83 40 02 00 00 48 8b 93 48 02 00 00 <48> 89 90 48 02 00 00 48 8b 93 48 02 00 00 48 89 82 40 02 00 00 
RIP  [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]
 RSP <ffff88027f66fee8>
CR2: 0000000000000248
---[ end trace 902dc79a9e72d3ed ]---
Kernel panic - not syncing: Aiee, killing interrupt handler!
------------[ cut here ]------------
WARNING: at kernel/smp.c:328 smp_call_function_mask+0x40/0x1cb()
Modules linked in: cciss(+) ehci_hcd ohci_hcd uhci_hcd

Pid: 0, comm: swapper Tainted: G D 2.6.27-rc3-git7 #1

Call Trace:
 <IRQ>  [<ffffffff802353a9>] warn_on_slowpath+0x58/0x7f
 [<ffffffff80235513>] ? __call_console_drivers+0x65/0x76
 [<ffffffff8024a28b>] ? up+0x34/0x39
 [<ffffffff802359e4>] ? release_console_sem+0x182/0x18b
 [<ffffffff80251d5d>] smp_call_function_mask+0x40/0x1cb
 [<ffffffff8021d58f>] ? stop_this_cpu+0x0/0x1d
 [<ffffffff80552e9b>] ? mutex_unlock+0x9/0xb
 [<ffffffff8025b2fe>] ? crash_kexec+0xe8/0xf2
 [<ffffffff802359e4>] ? release_console_sem+0x182/0x18b
 [<ffffffff80251f03>] smp_call_function+0x1b/0x1d
 [<ffffffff8021d5f5>] native_smp_send_stop+0x22/0x30
 [<ffffffff802352a5>] panic+0xaf/0x15b
 [<ffffffff8024a63a>] ? blocking_notifier_call_chain+0xf/0x11
 [<ffffffff80237e00>] do_exit+0x78/0x84d
 [<ffffffff803db66d>] ? do_unblank_screen+0x2e/0x12a
 [<ffffffff805546de>] oops_begin+0x0/0x96
 [<ffffffff80556655>] do_page_fault+0x72e/0x7dd
 [<ffffffff8022c4d3>] ? __enqueue_entity+0x8d/0x8f
 [<ffffffff80554319>] error_exit+0x0/0x51
 [<ffffffffa001bb68>] ? do_cciss_intr+0x627/0xa6c [cciss]
 [<ffffffffa001bf42>] ? do_cciss_intr+0xa01/0xa6c [cciss]
 [<ffffffff8026757e>] handle_IRQ_event+0x27/0x57
 [<ffffffff80268d08>] handle_edge_irq+0xed/0x12e
 [<ffffffff8020eaab>] do_IRQ+0xf6/0x167
 [<ffffffff8020c471>] ret_from_intr+0x0/0xa
 <EOI>  [<ffffffff802122b1>] ? default_idle+0x2b/0x40
 [<ffffffff802124bf>] ? c1e_idle+0xd4/0xdb
 [<ffffffff8055677d>] ? atomic_notifier_call_chain+0xf/0x11
 [<ffffffff8020ac6c>] ? cpu_idle+0x71/0x8f
 [<ffffffff8054e752>] ? start_secondary+0x157/0x15c

---[ end trace 902dc79a9e72d3ed ]---

Randy,
We know of a race condition in cciss_init_one. It's fixed in 2.6.26 I believe. Here's the patch:

http://groups.google.com/group/linux.kernel/browse_thread/thread/7b39f2b77622ab03/4f5f45c008655ca1?hl=en&lnk=gst&q=cciss#4f5f45c008655ca1

-- mikem

Mike,
Sorry, but my fingers have typoed the $subject. My bad. Kernel is 2.6.27-rc3-git7 (from above):

---
~Randy
Linux Plumbers Conference, 17-19 September 2008, Portland, Oregon USA
http://linuxplumbersconf.org/

Hmmmmm, let me know what happens from your retest. I'll look at this as soon as I finish what I'm doing now. We trying to spin for our test teams but I have something hopelessly broken. :(

-- mikem

It didn't BUG in the retest. That just means that it's more difficult to find/fix, right?

---
~Randy
Linux Plumbers Conference, 17-19 September 2008, Portland, Oregon USA
http://linuxplumbersconf.org/

Yup.

Randy,

If you can't reproduce it, could you use the debug information or gdb to tell us what line in the source code this:

do_cciss_intr+0x627

corresponds to? That might help isolating the problem.

Thanks,

James

Sure, here's an attempt at that. Please let me know if you want it differently or some other info.

(gdb) x/20i do_cciss_intr+0x627

0x3b68 <do_cciss_intr+1575>:    mov    %rdx,0x248(%rax)
0x3b6f <do_cciss_intr+1582>:    mov    0x248(%rbx),%rdx
0x3b76 <do_cciss_intr+1589>:    mov    %rax,0x240(%rdx)
0x3b7d <do_cciss_intr+1596>:    jmp    0x3b8b <do_cciss_intr+1610>
0x3b7f <do_cciss_intr+1598>:    movq   $0x0,0x100c0(%r12)
0x3b8b <do_cciss_intr+1610>:    mov    0x234(%rbx),%eax
0x3b91 <do_cciss_intr+1616>:    test   %eax,%eax
0x3b93 <do_cciss_intr+1618>:    jne    0x3f27 <do_cciss_intr+2534>
0x3b99 <do_cciss_intr+1624>:    mov    0x250(%rbx),%r14
0x3ba0 <do_cciss_intr+1631>:    movl   $0x0,0xcc(%r14)
0x3bab <do_cciss_intr+1642>:    mov    0x228(%rbx),%r8
0x3bb2 <do_cciss_intr+1649>:    mov    0x2(%r8),%dx
0x3bb7 <do_cciss_intr+1654>:    test   %dx,%dx
0x3bba <do_cciss_intr+1657>:    je     0x3f0e <do_cciss_intr+2509>

$ addr2line -e cciss.o -f  do_cciss_intr+0x627
SA5_fifo_full
/home/rdunlap/linsrc/linux-2.6.27-rc3-git7/drivers/block/cciss.h:206

$ ../../scripts/decodecode  < cciss.code 
Code: 8b 83 48 02 00 00 48 39 d8 74 37 49 39 9c 24 c0 00 01 00 75 08 49 89 84 24 c0 00 01 00 48 8b 83 40 02 00 00 48 8b 93 48 02 00 00 <48> 89 90 48 02 00 00 48 8b 93 48 02 00 00 48 89 82 40 02 00 00

/tmp/tmp.HbrjP23089.o: file format elf64-x86-64

Disassembly of section .text:

0000000000000000 <.text>:

   0:   8b 83 48 02 00 00       mov    0x248(%rbx),%eax
   6:   48 39 d8                cmp    %rbx,%rax
   9:   74 37                   je     0x42
   b:   49 39 9c 24 c0 00 01    cmp    %rbx,0x100c0(%r12)
  12:   00 
  13:   75 08                   jne    0x1d
  15:   49 89 84 24 c0 00 01    mov    %rax,0x100c0(%r12)
  1c:   00 
  1d:   48 8b 83 40 02 00 00    mov    0x240(%rbx),%rax
  24:   48 8b 93 48 02 00 00    mov    0x248(%rbx),%rdx

/tmp/tmp.HbrjP23089.o: file format elf64-x86-64

Disassembly of section .text:

0000000000000000 <.text>:

   0:   48 89 90 48 02 00 00    mov    %rdx,0x248(%rax)
   7:   48 8b 93 48 02 00 00    mov    0x248(%rbx),%rdx
   e:   48 89 82 40 02 00 00    mov    %rax,0x240(%rdx)

~Randy

OK ...that's confusing. It seems to be saying that ctrlr_info_t * was NULL. However, I can't see a way of getting into the fifo_full callback from do_cciss_intr .. especially not with an NULL host.

James

That is weird. Even if we could get there fifo_full doesn't do anything but wait for a bit.

mikem

Hi,

This just happened again. This time it's on 2.6.27-rc5-git3.

~Randy

Thanks Randy. I think. :)

I'll try to recreate in my lab.

-- mikem

This looks somewhat strange, mostly like 'c' is NULL and it's oopsing in in removeQ (I don't think Randy's analysis is correct in assuming it's 'h' and it's in fifo_full). Given that 'c' cannot be NULL, it's c->prev or c->next that are NULL.

Jens Axboe

Yes, correct IMO. I checked my daily test logs and I have had this problem in do_cciss_intr() 3 times, all at the same location, which appears to be in removeQ(), as Jens says.

~Randy

Mike, also notice this: it's always during driver init, as indicated by the (+) in the dump ('+' means that the module is in the process of being loaded, but module load has not completed):

calling cciss_init+0x0/0x2e [cciss]
HP CISS Driver (v 3.6.20)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 54
cciss 0000:42:08.0: PCI INT A -> Link[LNKA] -> GSI 54 (level, high) -> IRQ 54
cciss0: <0x3238> at PCI 0000:42:08.0 IRQ 503 using DAC

BUG: unable to handle kernel NULL pointer dereference at 0000000000000248
IP: [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]
PGD 17e422067 PUD 17e423067 PMD 0
Oops: 0002 [1] SMP
CPU 2
Modules linked in: cciss(+) ehci_hcd ohci_hcd uhci_hcd
Pid: 0, comm: swapper Not tainted 2.6.27-rc3-git7 #1
RIP: 0010:[<ffffffffa001bb68>]  [<ffffffffa001bb68>] do_cciss_intr+0x627/0xa6c [cciss]

---
~Randy

Thanks, Randy

This BUG: has happened (now) 5 times today. Higher frequency than usual for some reason.

I enabled CCISS_DEBUG and added one printk in removeQ(). On the first call to removeQ(), both c->next and c->prev are NULL.

Here's the kernel log output from cciss:

cciss 0000:42:08.0: PCI INT A -> Link[LNKA] -> GSI 54 (level, high) -> IRQ 54 command = 147
irq = 36
board_id = 3211103c
cciss 0000:42:08.0: irq 87 for MSI/MSI-X
address 0 = fdf80000
cfg base address = 10
cfg base address index = 0
cfg offset = 400
Controller Configuration information
------------------------------------
Signature = CISS
Spec Number = 1
Transport methods supported = 0x6
Transport methods active = 0x3
Requested transport Method = 0x0
Coalesce Interrupt Delay = 0x0
Coalesce Interrupt Count = 0x1
Max outstanding commands = 0x256
Bus Types = 0x200000
Server Name =
Heartbeat Counter = 0xffc

Trying to put board into Simple mode
I counter got to 1 0
Controller Configuration information
------------------------------------
Signature = CISS
Spec Number = 1
Transport methods supported = 0x6
Transport methods active = 0x3
Requested transport Method = 0x0
Coalesce Interrupt Delay = 0x0
Coalesce Interrupt Count = 0x1
Max outstanding commands = 0x256
Bus Types = 0x200000
Server Name =
Heartbeat Counter = 0xffc

cciss0: <0x3238> at PCI 0000:42:08.0 IRQ 87 using DAC
cciss: intr_pending 8
cciss: removeQ: Qptr=ffff88027e7500b8, c=ffff88007f83e000, next=ffff88007f83e000, prev=ffff88007f83e000 Sending 7f83e000 - down to controller
cciss: intr_pending 8
cciss: Read 4 back from board
cciss: removeQ: Qptr=ffff88027e7500c0, c=ffff88007f840000, next=0000000000000000, prev=0000000000000000

BUG: unable to handle kernel NULL pointer dereference at 0000000000000248
IP: [<ffffffffa002502b>] do_cciss_intr+0x6c8/0xb10 [cciss]
PGD 0
Oops: 0002 [#1] SMP
last sysfs file: /sys/block/ram15/dev
CPU 2
Modules linked in: cciss(+) ehci_hcd ohci_hcd uhci_hcd
Pid: 0, comm: swapper Not tainted 2.6.28-rc5 #1
RIP: 0010:[<ffffffffa002502b>]  [<ffffffffa002502b>] do_cciss_intr+0x6c8/0xb10 [cciss]
RSP: 0018:ffff88017fa9fee8  EFLAGS: 00010087
RAX: 0000000000000000 RBX: ffff88007f840000 RCX: 000000000000a3d9
RDX: 0000000000000000 RSI: 0000000000000046 RDI: ffffffff8080e634
RBP: ffff88017fa9ff18 R08: 0000000000000000 R09: ffff88017e918800
R10: 0000000000000000 R11: 0000000000000000 R12: ffff88027e740000
R13: 0000000000000000 R14: 0000000000000057 R15: 0000000000000086
FS:  00000000008558f0(0000) GS:ffff88017fc01c80(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000248 CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff88027f660000, task ffff88027f635400)
Stack:
 0000000000000030 ffff88017ea73640 0000000000000000 0000000000000000
 0000000000000057 0000000000000000 ffff88017fa9ff48 ffffffff8026a8b9
 ffffffff8074ab00 0000000000000057 ffff88017ea73640 ffffffff8074ab58
Call Trace:
 <IRQ> <0> [<ffffffff8026a8b9>] handle_IRQ_event+0x27/0x57
 [<ffffffff8026c424>] handle_edge_irq+0xde/0x11f
 [<ffffffff8020e29b>] do_IRQ+0xfc/0x175
 [<ffffffff8020c3e6>] ret_from_intr+0x0/0xa
 <EOI> <0> [<ffffffff8023c7d2>] ? ksoftirqd+0x0/0xa6
 [<ffffffff80212575>] ? default_idle+0x2b/0x40
 [<ffffffff80212799>] ? c1e_idle+0xe5/0xec
 [<ffffffff8056a7f6>] ? atomic_notifier_call_chain+0xf/0x11
 [<ffffffff8020acd1>] ? cpu_idle+0x40/0x5e
 [<ffffffff8056284e>] ? start_secondary+0x174/0x179
Code: 8b 83 48 02 00 00 48 39 d8 74 37 49 39 9c 24 c0 00 01 00 75 08 49 89 84 24 c0 00 01 00 48 8b 83 40 02 00 00 48 8b 93 48 02 00 00 <48> 89 90 48 02 00 00 48 8b 93 48 02 00 00 48 89 82 40 02 00 00
RIP  [<ffffffffa002502b>] do_cciss_intr+0x6c8/0xb10 [cciss]
 RSP <ffff88017fa9fee8>
CR2: 0000000000000248
Kernel panic - not syncing: Fatal exception in interrupt

Any ideas/suggestions?

Thanks,
~Randy

s/first/second/

I added a printk() in addQ() as well. Here's the new output:

HP CISS Driver (v 3.6.20)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 54
cciss 0000:42:08.0: PCI INT A -> Link[LNKA] -> GSI 54 (level, high) -> IRQ 54 command = 147
irq = 36
board_id = 3211103c
cciss 0000:42:08.0: irq 87 for MSI/MSI-X
address 0 = fdf80000
cfg base address = 10
cfg base address index = 0
cfg offset = 400
Controller Configuration information
------------------------------------
Signature = CISS
Spec Number = 1
Transport methods supported = 0x6
Transport methods active = 0x3
Requested transport Method = 0x0
Coalesce Interrupt Delay = 0x0
Coalesce Interrupt Count = 0x1
Max outstanding commands = 0x256
Bus Types = 0x200000
Server Name =
Heartbeat Counter = 0x1672

Trying to put board into Simple mode
I counter got to 1 0
Controller Configuration information
------------------------------------
Signature = CISS
Spec Number = 1
Transport methods supported = 0x6
Transport methods active = 0x3
Requested transport Method = 0x0
Coalesce Interrupt Delay = 0x0
Coalesce Interrupt Count = 0x1
Max outstanding commands = 0x256
Bus Types = 0x200000
Server Name =
Heartbeat Counter = 0x1672

cciss0: <0x3238> at PCI 0000:42:08.0 IRQ 87 using DAC
cciss: intr_pending 8
cciss: addQ: Qptr=ffff88027e0100b8, c=ffff88007f83e000
cciss: removeQ: Qptr=ffff88027e0100b8, c=ffff88007f83e000, next=ffff88007f83e000, prev=ffff88007f83e000 Sending 7f83e000 - down to controller
cciss: addQ: Qptr=ffff88027e0100c0, c=ffff88007f83e000
cciss: intr_pending 8
cciss: Read 4 back from board
cciss: removeQ: Qptr=ffff88027e0100c0, c=ffff88007f840000, next=0000000000000000, prev=0000000000000000

BUG: unable to handle kernel NULL pointer dereference at 0000000000000248
IP: [<ffffffffa0025106>] do_cciss_intr+0x706/0xb6c [cciss]
PGD 0
Oops: 0002 [#1] SMP
last sysfs file: /sys/block/ram15/dev
CPU 2
Modules linked in: cciss(+) ehci_hcd ohci_hcd uhci_hcd
Pid: 0, comm: swapper Not tainted 2.6.28-rc5 #1
RIP: 0010:[<ffffffffa0025106>]  [<ffffffffa0025106>] do_cciss_intr+0x706/0xb6c [cciss]
RSP: 0018:ffff88027f643ee8  EFLAGS: 00010087
RAX: 0000000000000000 RBX: ffff88007f840000 RCX: 000000000000a44f
RDX: 0000000000000000 RSI: 0000000000000046 RDI: ffffffff8080e634
RBP: ffff88027f643f18 R08: 0000000000000000 R09: ffff88017e964800
R10: 0000000000000000 R11: 0000000000000000 R12: ffff88027e000000
R13: 0000000000000000 R14: 0000000000000057 R15: 0000000000000086
FS:  00000000008558f0(0000) GS:ffff88017fc01c80(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000248 CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff88017fa9e000, task ffff88017fa5d400)
Stack:
 0000000000000030 ffff88027f627500 0000000000000000 0000000000000000
 0000000000000057 0000000000000000 ffff88027f643f48 ffffffff8026a8b9
 ffffffff8074ab00 0000000000000057 ffff88027f627500 ffffffff8074ab58
Call Trace:
 <IRQ> <0> [<ffffffff8026a8b9>] handle_IRQ_event+0x27/0x57
 [<ffffffff8026c424>] handle_edge_irq+0xde/0x11f
 [<ffffffff8020e29b>] do_IRQ+0xfc/0x175
 [<ffffffff8020c3e6>] ret_from_intr+0x0/0xa
 <EOI> <0> [<ffffffff8023c7d2>] ? ksoftirqd+0x0/0xa6
 [<ffffffff80212575>] ? default_idle+0x2b/0x40
 [<ffffffff80212799>] ? c1e_idle+0xe5/0xec
 [<ffffffff8056a7f6>] ? atomic_notifier_call_chain+0xf/0x11
 [<ffffffff8020acd1>] ? cpu_idle+0x40/0x5e
 [<ffffffff8056284e>] ? start_secondary+0x174/0x179
Code: 8b 83 48 02 00 00 48 39 d8 74 37 49 39 9c 24 c0 00 01 00 75 08 49 89 84 24 c0 00 01 00 48 8b 83 40 02 00 00 48 8b 93 48 02 00 00 <48> 89 90 48 02 00 00 48 8b 93 48 02 00 00 48 89 82 40 02 00 00
RIP  [<ffffffffa0025106>] do_cciss_intr+0x706/0xb6c [cciss]
 RSP <ffff88027f643ee8>
CR2: 0000000000000248
Kernel panic - not syncing: Fatal exception in interrupt

~Randy

Randy, can you post the debug patch you used? The above goes boom when it attempts to remove a command that isn't on the list, the Qptr in the last example should be empty, hence the oops. So I'd be interested in seeing what removeQ() calls this is, I'm assuming it's this bit in do_cciss_intr():

      ...
              while (c->busaddr != a) {
                       c = c->next;
                       if (c == h->cmpQ)
                               break;
               }
       }
       /*
        * If we've found the command, take it off the
        * completion Q and free it
        */
       if (c->busaddr == a) {
               removeQ(&h->cmpQ, c);
               if (c->cmd_type == CMD_RWREQ) {
                       complete_command(h, c, 0);
                        ...

If so, what part of the c lookup are you hitting - the on that does:

        c = h->cmd_pool + a2;

or the c->busaddr check that his shown above?

Jens Axboe

Randy,
I still can't reproduce this bug. I have your config file on a BL465c w/e200i. Just to confirm, you only see this at init time, correct? Please post your debug patch as Jens requested.

-- mikem

Yes, only at init time.

Done (separately).

I need to back up a bit. Yesterday these BUGs happened consistenly, so I wondered why. Then I recalled that for debugging another bug/problem, I had changed the test system's normal boot kernel from 2.6.25 to 2.6.18-8. The test system is used to build and then boot the new kernel *via kexec*, so it's quite possible (or certain) that something in the kexec world has been fixed since 2.6.18. I don't recall seeing this problem lately when using 2.6.25 to kexec/boot the new test kernel, so I'm quite willing to drop the bug for now and then re-open it if I see the problem again. OK??

~Randy

Ahhhh, the kexec piece was missing. Now I don't feel quite so clueless. I'm OK with dropping the bug for now. Jens, James?

-- mikem

Yeah, kexec is definitely a clue. My guess is that we got some sort of left over completion. Regardless of the status of this particular bug or not, I think it would be a good idea to add some checks for when a command is attempted removed from a queue it isn't currently on.

Jens Axboe

I agree, I'll fix.

-- mikem

I'd propose just converting it to list_head instead of doing it manually. Heck, that should be a 5 minute job, let me just do it...

OK, here it is, totally untested (it compiles, must be golden...)

 3 files changed, 24 insertions(+), 40 deletions(-)

index 12de1fd..d2923de 100644
@@ -215,30 +215,17 @@ static struct block_device_operations cciss_fops = {
 /*
  * Enqueuing and dequeuing functions for cmdlists.
  */
-static inline void addQ(CommandList_struct **Qptr, CommandList_struct *c)
+static inline void addQ(struct list_head *list, CommandList_struct *c)
 {
-	if (*Qptr == NULL) {
-		*Qptr = c;
-		c->next = c->prev = c;
-	} else {
-		c->prev = (*Qptr)->prev;
-		c->next = (*Qptr);
-		(*Qptr)->prev->next = c;
-		(*Qptr)->prev = c;
-	}
+	list_add(&c->list, list);
 }
 
-static inline CommandList_struct *removeQ(CommandList_struct **Qptr,
-					  CommandList_struct *c)
+static inline CommandList_struct *removeQ(CommandList_struct *c)
 {
-	if (c && c->next != c) {
-		if (*Qptr == c)
-			*Qptr = c->next;
-		c->prev->next = c->next;
-		c->next->prev = c->prev;
-	} else {
-		*Qptr = NULL;
-	}
+	if (WARN_ON(list_empty(&c->list)))
+		return NULL;
+
+	list_del_init(&c->list);
 	return c;
 }
 

@@ -506,6 +493,7 @@ static CommandList_struct *cmd_alloc(ctlr_info_t *h, int get_from_pool)
 		c->cmdindex = i;
 	}
 
+	INIT_LIST_HEAD(&c->list);
 	c->busaddr = (__u32) cmd_dma_handle;
 	temp64.val = (__u64) err_dma_handle;
 	c->ErrDesc.Addr.lower = temp64.val32.lower;

@@ -2543,7 +2531,8 @@ static void start_io(ctlr_info_t *h)
 {
 	CommandList_struct *c;
 
-	while ((c = h->reqQ) != NULL) {
+	while (!list_empty(&h->reqQ)) {
+		c = list_entry(h->reqQ.next, CommandList_struct, list);
 		/* can't do anything if fifo is full */
 		if ((h->access.fifo_full(h))) {
 			printk(KERN_WARNING "cciss: fifo full\n");

@@ -2551,7 +2540,7 @@ static void start_io(ctlr_info_t *h)
 		}
 
 		/* Get the first entry from the Request Q */
-		removeQ(&(h->reqQ), c);
+		removeQ(c);
 		h->Qdepth--;
 
 		/* Tell the controller execute command */

@@ -2981,15 +2970,8 @@ static irqreturn_t do_cciss_intr(int irq, void *dev_id)
 
 			} else {
 				a &= ~3;
-				if ((c = h->cmpQ) == NULL) {
-					printk(KERN_WARNING
-					       "cciss: Completion of %08x ignored\n",
-					       a1);
-					continue;
-				}
-				while (c->busaddr != a) {
-					c = c->next;
-					if (c == h->cmpQ)
+				list_for_each_entry(c, &h->cmpQ, list) {
+					if (c->busaddr == a)
 						break;
 				}
 			}

@@ -2998,7 +2980,7 @@ static irqreturn_t do_cciss_intr(int irq, void *dev_id)
 			 * completion Q and free it
 			 */
 			if (c->busaddr == a) {
-				removeQ(&h->cmpQ, c);
+				removeQ(c);
 				if (c->cmd_type == CMD_RWREQ) {
 					complete_command(h, c, 0);
 				} else if (c->cmd_type == CMD_IOCTL_PEND) {

@@ -3417,6 +3399,8 @@ static int __devinit cciss_init_one(struct pci_dev *pdev,
 		return -1;
 
 	hba[i]->busy_initializing = 1;
+	INIT_LIST_HEAD(&hba[i]->cmpQ);
+	INIT_LIST_HEAD(&hba[i]->reqQ);
 
 	if (cciss_pci_init(hba[i], pdev) != 0)
 		goto clean1;

@@ -3724,15 +3708,16 @@ static void fail_all_cmds(unsigned long ctlr)
 	pci_disable_device(h->pdev);	/* Make sure it is really dead. */
 
 	/* move everything off the request queue onto the completed queue */
-	while ((c = h->reqQ) != NULL) {
-		removeQ(&(h->reqQ), c);
+	while (!list_empty(&h->reqQ)) {
+		c = list_entry(h->reqQ.next, CommandList_struct, list);
+		removeQ(c);
 		h->Qdepth--;
 		addQ(&(h->cmpQ), c);
 	}
 
 	/* Now, fail everything on the completed queue with a HW error */
-	while ((c = h->cmpQ) != NULL) {
-		removeQ(&h->cmpQ, c);
+	while (!list_empty(&h->cmpQ)) {
+		removeQ(c);
 		c->err_info->CommandStatus = CMD_HARDWARE_ERR;
 		if (c->cmd_type == CMD_RWREQ) {
 			complete_command(h, c, 0);

index 24a7efa..5a9806a 100644
@@ -89,8 +89,8 @@ struct ctlr_info
 	struct access_method access;
 
 	/* queue and queue Info */ 
-	CommandList_struct *reqQ;
-	CommandList_struct  *cmpQ;
+	struct list_head reqQ;
+	struct list_head cmpQ;
 	unsigned int Qdepth;
 	unsigned int maxQsinceinit;
 	unsigned int maxSG;

index 43bf559..899cc0e 100644
@@ -265,8 +265,7 @@ typedef struct _CommandList_struct {
   int			   ctlr;
   int			   cmd_type; 
   long			   cmdindex;
-  struct _CommandList_struct *prev;
-  struct _CommandList_struct *next;
+  struct list_head list;
   struct request *	   rq;
   struct completion *waiting;
   int	 retry_count;

Jens Axboe

It was missing a list_entry() in fail_all_cmds(), apart from that it was fine. I changed it to use hlist instead, as that is more appropriate and similar to how it worked before. It also means there's no extra space usage in the controller structure. I've tested it and it works fine for me.

Mike, can you give this a look-over and give me a Reviewed-by or similar? As an extra bonus, it also gets rid of some code.

 3 files changed, 33 insertions(+), 46 deletions(-)

http://git.kernel.dk/?p=linux-2.6-block.git;a=commit;h=e303054e55acd1b6478b8859a5f8648bfaf69a44

Jens Axboe

That works for me. :)

Excellent, thanks Mike. If you could run it through a cycle or so of your regular testing, I'd feel 100% confident in it.

Jens Axboe