Using 2 Bridges Simultaneously for "Load Balancing"
Hello,
I have trouble entirely understanding the bridging concept in Linux. My problem:
I have a rather powerful workstation running Ubuntu 8.10 64 Bit. On this I want to use 4 virtual machines using VirtualBox. To split the network load I installed a second NIC in addition to the built-in one.
According to the VirtualBox Manual to use Host Interface Networking I need to create a bridge with a physical interface assigned to it. Then, virtual host interfaces are created and added to the bridge. These virtual interfaces then communicate via the bridge (and therefore, the physical interface) with the outside network/internet.
Now I thought it was possible to create to of those bridges, each one with one physical NIC. Then I could assign two virtual machines to each bridge/NIC in order to balance or distribute the load.
My trials weren't successful and I have the suspicion that the simultaneous use of two bridges is impossible. Can anyone make a suggestion for a working configuration or rid me of my illusions ;)?
Configuration:
Dell Precision T5400 with one built-in NIC and an additional one.
eth0: internal NIC
should be assigned to bridge br0
with vbox0 and vbox1 assigned (for the virtual boxes 0 and 1)
eth1: additional NIC
should be assigned to bridge br1
with vbox2 and vbox3 assigned (for the virtual boxes 2 and 3)
My (not working) /etc/network/interfaces configuration:
auto br0 br1
iface br0 inet static
address xxx.xxx.xxx.1 netmask 255.255.255.0 gateway xxx.xxx.xxx.254 bridge_ports eth0
iface br1 inet static
address xxx.xxx.xxx.2 netmask 255.255.255.0 gateway xxx.xxx.xxx.254 bridge_ports eth1
The nameserver is defined in the resolv.conf. I did not alter or adapt the routing tables, maybe that's the whole problem? On the other hand I read about STP but don't know if this applies here. If br1 is down I have access to the internet. After the activation of br1 in addition to br0, I have no connections to the outside world.
Any help would be greatly appreciated!
Waldgeist
Quoted 2 lines
My trials weren't successful and I have the suspicion that the simultaneous use of two bridges is impossible. Can anyone make a
It is possible. We use such configuration for pve.proxmox.com - works perfectly.
- Dietmar
Quoted 11 lines
iface br0 inet static
address xxx.xxx.xxx.1 netmask 255.255.255.0 gateway xxx.xxx.xxx.254 bridge_ports eth0iface br1 inet static
address xxx.xxx.xxx.2 netmask 255.255.255.0 gateway xxx.xxx.xxx.254 bridge_ports eth1
But AFAIK you can only have one gateway in debian.
- Dietmar
I think you do not need 2 addresses - try the following instead:
iface br0 inet static
address xxx.xxx.xxx.1 netmask 255.255.255.0 gateway xxx.xxx.xxx.254 bridge_ports eth0 bridge_stp off bridge_fd 0
iface br1 inet manual
bridge_ports eth1
bridge_stp off
bridge_fd 0
Quoted 6 lines
Now I thought it was possible to create to of those bridges, each one with one physical NIC. Then I could assign two virtual machines to each bridge/NIC in order to balance or distribute the load.
if you just want load balancing/distribute the load on the two NIC's: why dont you create a bond (some people/manufacturers call it also "trunk" or "LAG" ) out of physical NIC's and then bridge the bond?
http://www.mjmwired.net/kernel/Documentation/networking/bonding.txt
http://www.debianhelp.co.uk/bonding.htm
- Thomas
That was my first thought, but one of the two NICs doesn't seem to support that properly. I got the bond (without the bridge) up and running, but the additional (cheap) NIC wasn't used at all (I monitored the traffic via gkrellm). Pulling the plug out of the internal NIC resulted in the total loss of connectivity. That's not supposed to happen with a bond. I would have thought that the other NIC, in that case the additional one, would still provide network connection, albeit with reduced bandwidth.
Anyway, the proposal from Dietmar works perfectly now.
Quoted 17 lines · Thomas Mueller
Quoted 4 lines
Now I thought it was possible to create to of those bridges, each one with one physical NIC. Then I could assign two virtual machines to each bridge/NIC in order to balance or distribute the load.
if you just want load balancing/distribute the load on the two NIC's: why dont you create a bond (some people/manufacturers call it also "trunk" or "LAG" ) out of physical NIC's and then bridge the bond?
http://www.mjmwired.net/kernel/Documentation/networking/bonding.txt
http://www.debianhelp.co.uk/bonding.htm- Thomas
_______________________________________________
Bridge mailing list
[email protected]
https://lists.linux-foundation.org/mailman/listinfo/bridge