u-boot configurations for custom board with MPC 8265
Hi All,
I am using a custom powerpc board with MPC8265 ( 66/200/300 Mhz) , 32MB of SDRAM???? ( 0x00000000 - 0x01FFFFFF)? and
8 MB of Flash Simm ( 0xFF800000 -? 0xFFFFFFFF) .
I am modifying the MPC8260ads configurations to match my board but I don't see any messages being printed on the serial port. I am using Codewarrior USB TAP debugger to debug the u-boot code with an initialization file as follows:
setMMRBaseAddr 0x00000000
writemmr??????? SCCR??? 0x0000
writemmr??????? SYPCR?????????? 0xffffffc3
writemmr??????? RMR???????????????????? 0x0001
# Memory periodic timer prescaler
writemmr??????? MPTPR?????????? 0x3200
# Internal memory map register
writemmr??????? IMMR??? 0x04700000
#Change the debugger's base address to match the new register base setMMRBaseAddr 0x04700000
writemmr??????? BR0???????????? 0xff801001
writemmr??????? OR0???????????? 0xff800836
# CS2 is SDRAM, 64-bit port at 0x00000000
writemmr??????? BR2???????????? 0x00000041
writemmr??????? OR2???????????? 0xfe002ec0
# set 60x Bus assigned SDRAM Refresh Timer (PSRT) writemmr??????? PSRT??????????? 0x13 writemmr??????? MPTPR?????????? 0x2800
# 60x SDRAM Mode Register
# precharge all banks
writemmr??????? PSDMR?????????? 0x824b36a3
writemmr??????? PSDMR?????????? 0xaa4b36a3
# perform an access writemem.b????? 0x00000000????? 0x00 # cbr refresh
writemmr??????? PSDMR?????????? 0x8a4b36a3
# perform 8 accesses writemem.b????? 0x00000000????? 0xFF writemem.b????? 0x00000000????? 0xFF writemem.b????? 0x00000000????? 0xFF writemem.b????? 0x00000000????? 0xFF writemem.b????? 0x00000000????? 0xFF writemem.b????? 0x00000000????? 0xFF writemem.b????? 0x00000000????? 0xFF writemem.b????? 0x00000000????? 0xFF
# 60x SDRAM Mode Register
# Issue Mode register write
writemmr??????? PSDMR?????????? 0x9a4b36a3
writemem.b????? 0x00000190????? 0x00
writemmr??????? PSDMR?????????? 0xc24b36a3
With the above initialization file when I define CONFIG_IMMR to 0xF0000000 in u-boot it just doesn't go further and so I modified it to be same as the initilization file ( 0x0470000) and now I am stepping little further into the code but I am getting stuck at? a point in cpu_init_f in start.S.
Could anyone please let me know the exact configurations I need to define in mpc8260ads.h file in u-boot.
Any help is greatly appreciated.
Thanks in advance
Best Regards
Jyotshna
Hi Jyotshna,
Is your u-boot code doing any register initializations?
Quoted 6 lines
I am modifying the MPC8260ads configurations to match my board but I don't see any messages being printed on the serial port. I am using Codewarrior USB TAP debugger to debug the u-boot code with an initialization file as follows:
setMMRBaseAddr
0x00000000writemmr SCCR 0x0000 writemmr SYPCR 0xffffffc3 writemmr RMR 0x0001
Quoted 7 lines
# Memory periodic timer prescaler
writemmr MPTPR0x3200
# Internal memory map register
writemmr IMMR0x04700000With the above initialization file when I define
CONFIG_IMMRto0xF0000000in u-boot it just doesn't go further and so I modified it to be same as the initilization file (0x0470000) and now I am stepping little further into the code but I am getting stuck at a point incpu_init_finstart.S.
If the debugger has done the processor initialization part, trying to do the same in u-boot might cause problems. I'll suggest you to comment out the initialization from u-boot and try. Most probably, setting OR and BR registers in cpu_init_f might be the issue.
Regards,
Jayakrishnan
[U-Boot] scc-uart on mpc8265 not working
In reply to Jyotshna CherukuriHi All,
I am using a custom powerpc board with MPC8265 ( 66/200/300 Mhz) , 32MB of SDRAM???? ( 0x00000000 - 0x01FFFFFF)? and
8 MB of Flash Simm ( 0xFF800000 -? 0xFFFFFFFF) .
I am modifying the MPC8260ads configurations in u-boot to match my board but I don't
see any messages being printed on the serial console. Can anyone please let me know what I need to change in u-boot to initialize the console properly. Do I need to go into the routine board_early_init_f for MPC8265 ? Please let me know
Thanks in advance
Best Regards
Jyotshna
[U-Boot] u-boot debug help
Hi ,
Could anyone please let me know the steps I need to follow to enable debug mode for u-boot .
Thanks
Jyotshna