ERROR: Unidentified device type 0
Hi,
I've got the ASUS P6T WS Professional mainboard including Marvell 88SE6320 SAS controller and attached a single Seagate 10k6 SAS harddrive to the first SAS port.
Installation of openSUSE 11.1rc1 went well but after rebooting, the harddrive doesn't get found. When the initrd script loads the mvsas module, the following output appears on screen:
sas: phy-10:1 added to port-10:0, phy_mask:0x2 ( 0)
ERROR: Unidentified device type 0
I first tried to install openSUSE 11.0 but the installer didn't find the harddrive. If I recall correctly, it was for the same reason as it is now when trying to boot the 11.1rc1 system.
So I think, there exists already a fix for this issue, as the 11.1rc1 installer sees the drive, which is still missing in the initrd environment.
I really would like to help solving this issue, but I need a pointer where and how to start digging. I've started a openSUSE bug (https://bugzilla.novell.com/show_bug.cgi?id=450302, Bug 450302 - mvsas doesn't find SAS drive anymore after installation) almost a week ago but didn't get much help there.
I'd really appreciate some help to get the new system running. Thanks in advance.
Bye.
Signature · 2 lines
Dipl.-Inform. (FH) Reinhard Nissl mailto:[email protected]
mvsas determines most often an incorrect phy addr of 0 while attaching phy to port (Was: ERROR: Unidentified device type 0)
Hi,
I've meanwhile investigated this issue a little bit further and changed the subject accordingly.
Quoted 8 lines · Reinhard Nissl
I've got the ASUS P6T WS Professional mainboard including Marvell 88SE6320 SAS controller and attached a single Seagate 10k6 SAS harddrive to the first SAS port.
Installation of openSUSE 11.1rc1 went well but after rebooting, the harddrive doesn't get found. When the initrd script loads the mvsas module, the following output appears on screen:
Quoted 6 lines
sas: phy-10:1 added to port-10:0, phy_mask:0x2 ( 0)
ERROR: Unidentified device type 0I first tried to install openSUSE 11.0 but the installer didn't find the harddrive. If I recall correctly, it was for the same reason as it is now when trying to boot the 11.1rc1 system.
This was not completely correct. I forgot that the 11.0 installer saw the drive at least once. And my investigations today showed that the 11.1rc1 installer / rescue system can run into the same error. But most often they see the drive (sometimes only after a power cycle) while initrd didn't succeed at all (looks like a timing issue).
Quoted 9 lines
So I think, there exists already a fix for this issue, as the 11.1rc1 installer sees the drive, which is still missing in the initrd environment.
I really would like to help solving this issue, but I need a pointer where and how to start digging. I've started a openSUSE bug (https://bugzilla.novell.com/show_bug.cgi?id=450302, Bug 450302 - mvsas doesn't find SAS drive anymore after installation) almost a week ago but didn't get much help there.
Some more findings:
After the rescue system booted successfully and detected the drive, I tried to unload mvsas. modprobe -r mvsas didn't succeed as the module was still in use, but lsmod didn't report any user. So I've unloaded mvsas with rmmod -f mvsas which succeeded. After that, modprobe mvsas was loading the module successfully again but the above error appeared. I've put up a loop with modprobe -r / modprobe but it never succeeded to detect the drive anymore.
My plans for the next days are to attach a SATA drive to one of the south bridge SATA ports, install an openSUSE system there which I will use to investigate this issue further, i. e. setup a build environment to be able to compile the module, activate (and possibly add additional) debug output and load the module without having to reboot.
I really hope that someone will drop me some lines to guide me in investigating this issue. Thanks in advance.
Bye.
Signature · 2 lines
Dipl.-Inform. (FH) Reinhard Nissl mailto:[email protected]