Skip to contentSkip to conversation

libata: Add OCTEON Compact Flash driver (v7).

PATCH New David Daney 1 participant 3 messages Jan 16, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover libata: Add OCTEON Compact Flash driver (v7).

Linus recently merged support for the mips/Octeon cpu.

please consider adding this driver for the Compact Flash system present on many of the OCTEON development boards.

Fixes from v6 as suggested by Alan Cox and described in patch 2/2.

This is a two part patch set, the first part adds a new column to the ata_timing table (for dmack_hold). This is used by the second patch which is the driver itself.

I will reply with the two patches.

Thanks,

David Daney (2):
libata: Add another column to the ata_timing table.
libata: New driver for OCTEON SOC Compact Flash interface (v7).

 drivers/ata/Kconfig          |    9 +
 drivers/ata/Makefile         |    1 +
 drivers/ata/libata-core.c    |   72 ++--
 drivers/ata/pata_octeon_cf.c |  965 
++++++++++++++++++++++++++++++++++++++++++
 include/linux/libata.h       |    9 +-
 5 files changed, 1018 insertions(+), 38 deletions(-)
 create mode 100644 drivers/ata/pata_octeon_cf.c
#1 lore raw

PATCH 1/2 libata: Add another column to the ata_timing table.

The forthcoming OCTEON SOC Compact Flash driver needs an additional timing value that was not available in the ata_timing table. I add a new column for dmack_hold time. The values were obtained from the Compact Flash specification Rev 4.1.

---
 drivers/ata/libata-core.c |   72 +++++++++++++++++++++++----------------------
 include/linux/libata.h    |    9 ++++--
 2 files changed, 43 insertions(+), 38 deletions(-)
drivers/ata/libata-core.c +37 -35
index 71218d7..8fe0012 100644
@@ -3029,33 +3029,33 @@ int sata_set_spd(struct ata_link *link)
  */
 
 static const struct ata_timing ata_timing[] = {
-/*	{ XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 960,   0 }, */
-	{ XFER_PIO_0,     70, 290, 240, 600, 165, 150, 600,   0 },
-	{ XFER_PIO_1,     50, 290,  93, 383, 125, 100, 383,   0 },
-	{ XFER_PIO_2,     30, 290,  40, 330, 100,  90, 240,   0 },
-	{ XFER_PIO_3,     30,  80,  70, 180,  80,  70, 180,   0 },
-	{ XFER_PIO_4,     25,  70,  25, 120,  70,  25, 120,   0 },
-	{ XFER_PIO_5,     15,  65,  25, 100,  65,  25, 100,   0 },
-	{ XFER_PIO_6,     10,  55,  20,  80,  55,  20,  80,   0 },
-
-	{ XFER_SW_DMA_0, 120,   0,   0,   0, 480, 480, 960,   0 },
-	{ XFER_SW_DMA_1,  90,   0,   0,   0, 240, 240, 480,   0 },
-	{ XFER_SW_DMA_2,  60,   0,   0,   0, 120, 120, 240,   0 },
-
-	{ XFER_MW_DMA_0,  60,   0,   0,   0, 215, 215, 480,   0 },
-	{ XFER_MW_DMA_1,  45,   0,   0,   0,  80,  50, 150,   0 },
-	{ XFER_MW_DMA_2,  25,   0,   0,   0,  70,  25, 120,   0 },
-	{ XFER_MW_DMA_3,  25,   0,   0,   0,  65,  25, 100,   0 },
-	{ XFER_MW_DMA_4,  25,   0,   0,   0,  55,  20,  80,   0 },
-
-/*	{ XFER_UDMA_SLOW,  0,   0,   0,   0,   0,   0,   0, 150 }, */
-	{ XFER_UDMA_0,     0,   0,   0,   0,   0,   0,   0, 120 },
-	{ XFER_UDMA_1,     0,   0,   0,   0,   0,   0,   0,  80 },
-	{ XFER_UDMA_2,     0,   0,   0,   0,   0,   0,   0,  60 },
-	{ XFER_UDMA_3,     0,   0,   0,   0,   0,   0,   0,  45 },
-	{ XFER_UDMA_4,     0,   0,   0,   0,   0,   0,   0,  30 },
-	{ XFER_UDMA_5,     0,   0,   0,   0,   0,   0,   0,  20 },
-	{ XFER_UDMA_6,     0,   0,   0,   0,   0,   0,   0,  15 },
+/*	{ XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 0,  960,   0 }, */
+	{ XFER_PIO_0,     70, 290, 240, 600, 165, 150, 0,  600,   0 },
+	{ XFER_PIO_1,     50, 290,  93, 383, 125, 100, 0,  383,   0 },
+	{ XFER_PIO_2,     30, 290,  40, 330, 100,  90, 0,  240,   0 },
+	{ XFER_PIO_3,     30,  80,  70, 180,  80,  70, 0,  180,   0 },
+	{ XFER_PIO_4,     25,  70,  25, 120,  70,  25, 0,  120,   0 },
+	{ XFER_PIO_5,     15,  65,  25, 100,  65,  25, 0,  100,   0 },
+	{ XFER_PIO_6,     10,  55,  20,  80,  55,  20, 0,   80,   0 },
+
+	{ XFER_SW_DMA_0, 120,   0,   0,   0, 480, 480, 50, 960,   0 },
+	{ XFER_SW_DMA_1,  90,   0,   0,   0, 240, 240, 30, 480,   0 },
+	{ XFER_SW_DMA_2,  60,   0,   0,   0, 120, 120, 20, 240,   0 },
+
+	{ XFER_MW_DMA_0,  60,   0,   0,   0, 215, 215, 20, 480,   0 },
+	{ XFER_MW_DMA_1,  45,   0,   0,   0,  80,  50, 5,  150,   0 },
+	{ XFER_MW_DMA_2,  25,   0,   0,   0,  70,  25, 5,  120,   0 },
+	{ XFER_MW_DMA_3,  25,   0,   0,   0,  65,  25, 5,  100,   0 },
+	{ XFER_MW_DMA_4,  25,   0,   0,   0,  55,  20, 5,   80,   0 },
+
+/*	{ XFER_UDMA_SLOW,  0,   0,   0,   0,   0,   0, 0,    0, 150 }, */
+	{ XFER_UDMA_0,     0,   0,   0,   0,   0,   0, 0,    0, 120 },
+	{ XFER_UDMA_1,     0,   0,   0,   0,   0,   0, 0,    0,  80 },
+	{ XFER_UDMA_2,     0,   0,   0,   0,   0,   0, 0,    0,  60 },
+	{ XFER_UDMA_3,     0,   0,   0,   0,   0,   0, 0,    0,  45 },
+	{ XFER_UDMA_4,     0,   0,   0,   0,   0,   0, 0,    0,  30 },
+	{ XFER_UDMA_5,     0,   0,   0,   0,   0,   0, 0,    0,  20 },
+	{ XFER_UDMA_6,     0,   0,   0,   0,   0,   0, 0,    0,  15 },
 
 	{ 0xFF }
 };
@@ -3065,14 +3065,15 @@ static const struct ata_timing ata_timing[] = {
 
 static void ata_timing_quantize(const struct ata_timing *t, struct ata_timing *q, int T, int UT)
 {
-	q->setup   = EZ(t->setup   * 1000,  T);
-	q->act8b   = EZ(t->act8b   * 1000,  T);
-	q->rec8b   = EZ(t->rec8b   * 1000,  T);
-	q->cyc8b   = EZ(t->cyc8b   * 1000,  T);
-	q->active  = EZ(t->active  * 1000,  T);
-	q->recover = EZ(t->recover * 1000,  T);
-	q->cycle   = EZ(t->cycle   * 1000,  T);
-	q->udma    = EZ(t->udma    * 1000, UT);
+	q->setup	= EZ(t->setup      * 1000,  T);
+	q->act8b	= EZ(t->act8b      * 1000,  T);
+	q->rec8b	= EZ(t->rec8b      * 1000,  T);
+	q->cyc8b	= EZ(t->cyc8b      * 1000,  T);
+	q->active	= EZ(t->active     * 1000,  T);
+	q->recover	= EZ(t->recover    * 1000,  T);
+	q->dmack_hold	= EZ(t->dmack_hold * 1000,  T);
+	q->cycle	= EZ(t->cycle      * 1000,  T);
+	q->udma		= EZ(t->udma       * 1000, UT);
 }
 
 void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
@@ -3084,6 +3085,7 @@ void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
 	if (what & ATA_TIMING_CYC8B  ) m->cyc8b   = max(a->cyc8b,   b->cyc8b);
 	if (what & ATA_TIMING_ACTIVE ) m->active  = max(a->active,  b->active);
 	if (what & ATA_TIMING_RECOVER) m->recover = max(a->recover, b->recover);
+	if (what & ATA_TIMING_DMACK_HOLD) m->dmack_hold = max(a->dmack_hold, b->dmack_hold);
 	if (what & ATA_TIMING_CYCLE  ) m->cycle   = max(a->cycle,   b->cycle);
 	if (what & ATA_TIMING_UDMA   ) m->udma    = max(a->udma,    b->udma);
 }
include/linux/libata.h +6 -3
index b6b8a7f..9c308b4 100644
@@ -401,12 +401,14 @@ enum {
 				  ATA_TIMING_CYC8B,
 	ATA_TIMING_ACTIVE	= (1 << 4),
 	ATA_TIMING_RECOVER	= (1 << 5),
-	ATA_TIMING_CYCLE	= (1 << 6),
-	ATA_TIMING_UDMA		= (1 << 7),
+	ATA_TIMING_DMACK_HOLD	= (1 << 6),
+	ATA_TIMING_CYCLE	= (1 << 7),
+	ATA_TIMING_UDMA		= (1 << 8),
 	ATA_TIMING_ALL		= ATA_TIMING_SETUP | ATA_TIMING_ACT8B |
 				  ATA_TIMING_REC8B | ATA_TIMING_CYC8B |
 				  ATA_TIMING_ACTIVE | ATA_TIMING_RECOVER |
-				  ATA_TIMING_CYCLE | ATA_TIMING_UDMA,
+				  ATA_TIMING_DMACK_HOLD | ATA_TIMING_CYCLE |
+				  ATA_TIMING_UDMA,
 };
 
 enum ata_xfer_mask {
@@ -866,6 +868,7 @@ struct ata_timing {
 	unsigned short cyc8b;		/* t0 for 8-bit I/O */
 	unsigned short active;		/* t2 or tD */
 	unsigned short recover;		/* t2i or tK */
+	unsigned short dmack_hold;	/* tj */
 	unsigned short cycle;		/* t0 */
 	unsigned short udma;		/* t2CYCTYP/2 */
 };
Signature · 1 line
1.5.6.6
#2 lore raw

PATCH 2/2 libata: New driver for OCTEON SOC Compact Flash interface (v7).

In reply to David Daney

Cavium OCTEON processor support was recently merged, so now we have this CF driver for your consideration.

Most OCTEON variants have *no* DMA or interrupt support on the CF interface so for these, only PIO is supported. Although if DMA is available, we do take advantage of it.

---

Differences from previous version (v6):

1) Spelling fixes in comments.

2) Added check_atapi_dma handler to the port operations.

Both changes as suggested by Alan Cox.

 drivers/ata/Kconfig          |    9 +
 drivers/ata/Makefile         |    1 +
 drivers/ata/pata_octeon_cf.c |  965 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 975 insertions(+), 0 deletions(-)
 create mode 100644 drivers/ata/pata_octeon_cf.c
drivers/ata/Kconfig +9 -0
index 1a7be96..503a908 100644
@@ -698,6 +698,15 @@ config PATA_IXP4XX_CF
 
 	  If unsure, say N.
 
+config PATA_OCTEON_CF
+	tristate "OCTEON Boot Bus Compact Flash support"
+	depends on CPU_CAVIUM_OCTEON
+	help
+	  This option enables a polled compact flash driver for use with
+	  compact flash cards attached to the OCTEON boot bus.
+
+	  If unsure, say N.
+
 config PATA_SCC
 	tristate "Toshiba's Cell Reference Set IDE support"
 	depends on PCI && PPC_CELLEB
drivers/ata/Makefile +1 -0
index 674965f..7f1ecf9 100644
@@ -69,6 +69,7 @@ obj-$(CONFIG_PATA_IXP4XX_CF)	+= pata_ixp4xx_cf.o
 obj-$(CONFIG_PATA_SCC)		+= pata_scc.o
 obj-$(CONFIG_PATA_SCH)		+= pata_sch.o
 obj-$(CONFIG_PATA_BF54X)	+= pata_bf54x.o
+obj-$(CONFIG_PATA_OCTEON_CF)	+= pata_octeon_cf.o
 obj-$(CONFIG_PATA_PLATFORM)	+= pata_platform.o
 obj-$(CONFIG_PATA_OF_PLATFORM)	+= pata_of_platform.o
 obj-$(CONFIG_PATA_ICSIDE)	+= pata_icside.o
drivers/ata/pata_octeon_cf.c new file +965 -0

965 lines not on this page · raw message

Signature · 1 line
1.5.6.6