Add Freescale MC44S803 tuner driver

---

Changes since v1:
- rebase against official linux tree. v1 was based against a local tree and didn't apply cleanly.

Changes since v2:
- fix typo KERN_ERROR -> KERN_ERR

Changes since v3:
- fix circuit adjust (reserved bits should be 1)
- don't initialize priv in mc44s803_attach()
- use a macro for printk to avoid duplicating the driver name over and over.

 drivers/media/common/tuners/Kconfig         |    8 +
 drivers/media/common/tuners/Makefile        |    1 +
 drivers/media/common/tuners/mc44s803.c      |  370 +++++++++++++++++++++++++++
 drivers/media/common/tuners/mc44s803.h      |   46 ++++
 drivers/media/common/tuners/mc44s803_priv.h |  208 +++++++++++++++
 5 files changed, 633 insertions(+), 0 deletions(-)
 create mode 100644 drivers/media/common/tuners/mc44s803.c
 create mode 100644 drivers/media/common/tuners/mc44s803.h
 create mode 100644 drivers/media/common/tuners/mc44s803_priv.h

index 6f92bea..7969b69 100644
@@ -29,6 +29,7 @@ config MEDIA_TUNER
 	select MEDIA_TUNER_TEA5767 if !MEDIA_TUNER_CUSTOMIZE
 	select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE
 	select MEDIA_TUNER_TDA9887 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_MC44S803 if !MEDIA_TUNER_CUSTOMIZE
 
 menuconfig MEDIA_TUNER_CUSTOMIZE
 	bool "Customize analog and hybrid tuner modules to build"

@@ -164,4 +165,11 @@ config MEDIA_TUNER_MXL5007T
 	help
 	  A driver for the silicon tuner MxL5007T from MaxLinear.
 
+config MEDIA_TUNER_MC44S803
+	tristate "Freescale MC44S803 Low Power CMOS Broadband tuners"
+	depends on VIDEO_MEDIA && I2C
+	default m if DVB_FE_CUSTOMISE
+	help
+	  Say Y here to support the Freescale MC44S803 based tuners
+
 endif # MEDIA_TUNER_CUSTOMIZE

index 4dfbe5b..4132b2b 100644
@@ -22,6 +22,7 @@ obj-$(CONFIG_MEDIA_TUNER_QT1010) += qt1010.o
 obj-$(CONFIG_MEDIA_TUNER_MT2131) += mt2131.o
 obj-$(CONFIG_MEDIA_TUNER_MXL5005S) += mxl5005s.o
 obj-$(CONFIG_MEDIA_TUNER_MXL5007T) += mxl5007t.o
+obj-$(CONFIG_MEDIA_TUNER_MC44S803) += mc44s803.o
 
 EXTRA_CFLAGS += -Idrivers/media/dvb/dvb-core
 EXTRA_CFLAGS += -Idrivers/media/dvb/frontends

1.5.6.5

Hello Jochen,
I just reviewed this patch and here is my comments;

[...]

http://palosaari.fi/

Hi All,
I have to apologize being a stupid newbie not able to put Antti's latest source (mc44s803-71b0ef33303a) into my kernel (2.6.27-11-generic).
Have performed successfully a "make", but running "install" failed because of missed option settings for this operation. I am uncertain if I must set a path directory. Is'nt there a symbolic link to the right directory? "make" compiled lots of not needed stuff here, but my system needs only a firmware file:
(Copied from /var/log/messages)

Jan 17 23:22:21 detlef-laptop kernel: [  155.512517] dvb-usb: found a 'TerraTec Cinergy T USB XE' in cold state, will try to load a firmware
Jan 17 23:22:21 detlef-laptop kernel: [  155.512530] firmware: requesting dvb-usb-af9015.fw
Jan 17 23:22:21 detlef-laptop kernel: [  155.526289] dvb_usb_af9015: probe of 4-3.3:1.0 failed with error -2

Maybe Antti can post me one which I simply can paste into /lib/firmware? Hopefully one of you can give an advice.. regards,
Detlef

Antti Palosaari schrieb: 2.6.27-11-generic

I don't understand what is happening.
What kind of error message you get?

Hmm, are you running "install" instead of "make install"?

"make" compiled lots of not needed stuff here, but my system

Here is the firmware I use.

http://www.otit.fi/~crope/v4l-dvb/af9015/af9015_firmware_cutter/firmware_files/4.95.0/dvb-usb-af9015.fw

I tried. :-)

   Roberto Ragusa    mail at robertoragusa.it

Good morning Roberto,
thanks for the firmware file which finally helped getting my DVB-T running! I pasted it in the /lib/firmware tree and could get a new message:

Jan 18 11:42:56 detlef-laptop kernel: [ 7677.396309] usb 4-3.3: new high
speed USB device using ehci_hcd and address 6
Jan 18 11:42:56 detlef-laptop kernel: [ 7677.517469] usb 4-3.3:
configuration #1 chosen from 1 choice
Jan 18 11:42:56 detlef-laptop kernel: [ 7677.548306] dvb-usb: found a
'TerraTec Cinergy T USB XE' in cold state, will try to load a firmware
Jan 18 11:42:56 detlef-laptop kernel: [ 7677.548318] firmware:
requesting dvb-usb-af9015.fw
Jan 18 11:42:56 detlef-laptop kernel: [ 7677.564421] dvb-usb:
downloading firmware from file 'dvb-usb-af9015.fw'
Jan 18 11:42:56 detlef-laptop kernel: [ 7677.648439] dvb-usb: found a
'TerraTec Cinergy T USB XE' in warm state.
Jan 18 11:42:56 detlef-laptop kernel: [ 7677.651636] dvb-usb: will pass
the complete MPEG2 transport stream to the software demuxer.
Jan 18 11:42:56 detlef-laptop kernel: [ 7677.653060] DVB: registering
new adapter (TerraTec Cinergy T USB XE)
Jan 18 11:42:57 detlef-laptop kernel: [ 7678.103047] af9013: firmware
version:4.95.0
Jan 18 11:42:57 detlef-laptop kernel: [ 7678.108177] DVB: registering
adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
Jan 18 11:42:57 detlef-laptop kernel: [ 7678.127280] mc44s803:
successfully identified (ID = 14)
Jan 18 11:42:57 detlef-laptop kernel: [ 7678.128910] dvb-usb: TerraTec

Cinergy T USB XE successfully initialized and connected. When compiling Antti's source I have tried "make install" in one step as root and got the message that "install" needs additional parameters. Same happened when trying first only "make" and next "install".

Anyway using Kaffeine my TV is running now! There are some configuration issues with this program but hopefully I will fix it soon. Thanks again and have a nice Sunday!

Regards
Detlef

-

Hi Antti,

OK, will fix.

This is definitely a BUG. I'll also fix this. Do you want me to post an update to the tuner or an incremental patch against your repository?

Thanks,
Jochen

Post new patch. I hope Mauro will pick up your patch and add it to the master when no more comments are given. Anyhow, I don't know what's correct procedure.

regards
Antti

http://palosaari.fi/