vbox cat's eye 3560 usb device
I’m trying to write a driver for the
device, just as a learning exercise. So far, I’ve got the firmware in intel hex format (from usbsnoop on windows, then a couple perl scripts to mutate it) and am able to use fxload to load it with –t fx2 and there are 2 separate files, a short one (the loader) and the firmware proper; so in fxload I have a –s and a –I.
I’m able to take it from cold to
warm that way solely within Linux.
The device itself has a cypress CY7C68013A fx2 chip and a large tin can tuner/demod stamped with Thomson that has a sticker on it identifying it as 8601A. Helpfully, the 3560 opens up easily with the removal of two screws on the shell.
It’s cold boot usb id is 14f3:3560 and its warm boot is 14f3:a560.
I have taken that hex file and
created a binary file out of the 2nd file (-I in fxload speak). I think, correct me if I’m wrong, there is already a fx2 loader available, thus I will not need the loader file.
One of the stranger things I saw in
the usbsnoop trace in windows was when it came to reset of the CPUCS, the driver sent down both a poke at x0e600 and a poke at 0x7f92. One is the fx CPUCS register, I believe the other is a fx2 CPUCS register.
Currently I am mutating dibusb-mc
just to see if I can get it to the point of going from cold to warm in the driver.
I have taken usb sniffs from windows
of doing things such as scanning for channels, watching a channel, etc. so I can try to figure out if anything else in the v4l-dvb collection behaves similarly.
I guess what I’m looking for is any
hints that might be useful to figuring this out.
Like I said, it’s a learning
exercise, I already have enough tuners, and anyway, the cost of buying a supported tuner is far cheaper than the time needed to develop this!
Thanks for any info! I’ve pretty
much devoured everything available on the wiki.
Amy
Hi Amy,
Quoted 7 lines · Amy Overmyer
I’m trying to write a driver for the
device, just as a learning exercise. So far, I’ve got the firmware in intel hex format (from usbsnoop on windows, then a couple perl scripts to mutate it) and am able to use fxload to load it with –t fx2 and there are 2 separate files, a short one (the loader) and the firmware proper; so in fxload I have a –s and a –I.
Quoted 7 lines
I’m able to take it from cold to
warm that way solely within Linux.The device itself has a cypress CY7C68013A fx2 chip and a large tin can tuner/demod stamped with Thomson that has a sticker on it identifying it as 8601A. Helpfully, the 3560 opens up easily with the removal of two screws on the shell.
The Thomson NIM is the same one that they use on their 150/151 PCI
cards. I don't know what the internal components of it are, but the
digital demodulator may be somewhat exposed to view -- the metal can has a ventilation opening, though the metal may actually be bent inwards for contact with the chip (so as to allow the casing to act as a
heatsink)). If you can ascertain the identity of the unknown
components then you will be in a better position to gauge whether you should bother continuing or not (i.e. if the demod is currently unsupported, you would have to develop support for it in order to ever get the device working under Linux). My suggestion here is:
- non-invasive: search for any clues from the Windows driver inf files
- invasive: as non-destructively as possible, open the can ... I don't advise this unless it looks do-able ... proceed at your own risk.
Lastly, are there any other IC components on the back or front of the PCB ? Can you provide pics (upload them to the wiki article)) ?
Quoted 26 lines
It’s cold boot usb id is 14f3:3560 and its warm boot is 14f3:a560.
I have taken that hex file and
created a binary file out of the 2nd file (-I in fxload speak). I think, correct me if I’m wrong, there is already a fx2 loader available, thus I will not need the loader file.One of the stranger things I saw in
the usbsnoop trace in windows was when it came to reset of the CPUCS, the driver sent down both a poke at x0e600 and a poke at0x7f92. One is the fx CPUCS register, I believe the other is a fx2 CPUCS register.Currently I am mutating dibusb-mc
just to see if I can get it to the point of going from cold to warm in the driver.I have taken usb sniffs from windows
of doing things such as scanning for channels, watching a channel, etc. so I can try to figure out if anything else in the v4l-dvb collection behaves similarly.I guess what I’m looking for is any
hints that might be useful to figuring this out.
Quoted 7 lines
Like I said, it’s a learning
exercise, I already have enough tuners, and anyway, the cost of buying a supported tuner is far cheaper than the time needed to develop this!Thanks for any info! I’ve pretty
much devoured everything available on the wiki.
have a look at the cxusb, its likely closer to what you want:
http://linuxtv.org/hg/v4l-dvb/file/tip/linux/drivers/media/dvb/dvb-usb/