Skip to contentSkip to conversation

epoll: clean up ep_modify

PATCH In review Tony Battersby 2 participants 2 messages Feb 24, 2009 – Feb 26, 2009 VFS

lore
Share & tools
lore
#0 lore raw

PATCH 5/6 epoll: clean up ep_modify

ep_modify() doesn't need to set event.data from within the ep->lock spinlock as the comment suggests. The only place event.data is used is ep_send_events_proc(), and this is protected by ep->mtx instead of ep->lock. Also update the comment for mutex_lock() at the top of ep_scan_ready_list(), which mentions epoll_ctl(EPOLL_CTL_DEL) but not epoll_ctl(EPOLL_CTL_MOD).

ep_modify() can also use spin_lock_irq() instead of spin_lock_irqsave().

---

This patch is against the current -mm tree, and might not apply to 2.6.29. Since this patch probably won't go into 2.6.29, you may apply this version of the patch after the other patches in -mm.

fs/eventpoll.c +7 -12
@@ -454,7 +454,7 @@ static int ep_scan_ready_list(struct eve
 
 	/*
 	 * We need to lock this because we could be hit by
-	 * eventpoll_release_file() and epoll_ctl(EPOLL_CTL_DEL).
+	 * eventpoll_release_file() and epoll_ctl().
 	 */
 	mutex_lock(&ep->mtx);
 
@@ -1037,15 +1037,14 @@ static int ep_modify(struct eventpoll *e
 {
 	int pwake = 0;
 	unsigned int revents;
-	unsigned long flags;
 
 	/*
-	 * Set the new event interest mask before calling f_op->poll(), otherwise
-	 * a potential race might occur. In fact if we do this operation inside
-	 * the lock, an event might happen between the f_op->poll() call and the
-	 * new event set registering.
+	 * Set the new event interest mask before calling f_op->poll();
+	 * otherwise we might miss an event that happens between the
+	 * f_op->poll() call and the new event set registering.
 	 */
 	epi->event.events = event->events;
+	epi->event.data = event->data; /* protected by mtx */
 
 	/*
 	 * Get current event bits. We can safely use the file* here because
@@ -1053,16 +1052,12 @@ static int ep_modify(struct eventpoll *e
 	 */
 	revents = epi->ffd.file->f_op->poll(epi->ffd.file, NULL);
 
-	spin_lock_irqsave(&ep->lock, flags);
-
-	/* Copy the data member from inside the lock */
-	epi->event.data = event->data;
-
 	/*
 	 * If the item is "hot" and it is not registered inside the ready
 	 * list, push it inside.
 	 */
 	if (revents & event->events) {
+		spin_lock_irq(&ep->lock);
 		if (!ep_is_linked(&epi->rdllink)) {
 			list_add_tail(&epi->rdllink, &ep->rdllist);
 
@@ -1072,8 +1067,8 @@ static int ep_modify(struct eventpoll *e
 			if (waitqueue_active(&ep->poll_wait))
 				pwake++;
 		}
+		spin_unlock_irq(&ep->lock);
 	}
-	spin_unlock_irqrestore(&ep->lock, flags);
 
 	/* We have to call this outside the lock */
 	if (pwake)
Acked-by on v1 5/6
#1 lore raw
Quoted 9 lines · Tony Battersby

ep_modify() doesn't need to set event.data from within the ep->lock spinlock as the comment suggests. The only place event.data is used is ep_send_events_proc(), and this is protected by ep->mtx instead of ep->lock. Also update the comment for mutex_lock() at the top of ep_scan_ready_list(), which mentions epoll_ctl(EPOLL_CTL_DEL) but not epoll_ctl(EPOLL_CTL_MOD).

ep_modify() can also use spin_lock_irq() instead of spin_lock_irqsave().

Pre-mtx stuff.

- Davide