Using tm6010 for Haupauge WinTV-HVR 900H
Hi out there
I'm in the unfortunate position of having bought a 900H instead of a 900 and now I'm fiddling with the driver.
Details:
$ lsusb | grep Hauppauge Bus 008 Device 004: ID 2040:6600 Hauppauge
My machine is running Ubuntu 8.10 with a 2.6.27-11-generic kernel. The correct kernel-headers are installed.
As far as I've read there is (limited) support for the device with the tm6010 driver. Putting together some info from the web I did the following:
$ hg clone http://linuxtv.org/hg/v4l-dvb $ cd v4l-dvb $ hg pull -u http://linuxtv.org/hg/~mchehab/tm6010
Inserted into v4l-dvb/v4l/.config three lines:CONFIG_VIDEO_TM6000_ALSA=mCONFIG_VIDEO_TM6000=mCONFIG_VIDEO_TM6000_DVB=m
$ hg merge $ make
and as root:
# make install
This far everything worked without error.
Then I got the Firmware the card was requesting in the dmesg-output from
http://steventoth.net/linux/hvr1400/xc3028L-v36.fw and copied it to /lib /firmware
Since there is no Module tm6000 I did
# modprobe -v tm6000 insmod /lib/modules/2.6.27-11-generic/kernel/drivers/media/video/videobuf-core.ko insmod /lib/modules/2.6.27-11-generic/kernel/drivers/media/video/videobuf-vmalloc.ko
insmod /lib/modules/2.6.27-11-generic/kernel/drivers/i2c/i2c-core.ko insmod /lib/modules/2.6.27-11-generic/kernel/drivers/media/video/tm6000/tm6000.ko
$ dmesg [ 187.646908] tm6000 v4l2 driver version 0.0.1 loaded [ 187.647898] usbcore: registered new interface driver tm6000
(tail /var/log/messages gives the same info)
Now - as I hope the module is loaded correctly - I attacht the USB-Device:
$ dmesg [ 373.881042] usb 8-1: new high speed USB device using ehci_hcd and address 3 [ 374.019648] usb 8-1: configuration #1 chosen from 1 choice [ 374.023090] tm6000: alt 0, interface 0, class 255 [ 374.023102] tm6000: alt 0, interface 0, class 255 [ 374.023107] tm6000: Bulk IN endpoint: 0x82 (max size=512 bytes) [ 374.023111] tm6000: alt 0, interface 0, class 255 [ 374.023116] tm6000: alt 1, interface 0, class 255 [ 374.023120] tm6000: ISOC IN endpoint: 0x81 (max size=3072 bytes) [ 374.023125] tm6000: alt 1, interface 0, class 255 [ 374.023129] tm6000: alt 1, interface 0, class 255 [ 374.023133] tm6000: alt 2, interface 0, class 255 [ 374.023137] tm6000: alt 2, interface 0, class 255 [ 374.023141] tm6000: alt 2, interface 0, class 255 [ 374.023145] tm6000: alt 3, interface 0, class 255 [ 374.023149] tm6000: alt 3, interface 0, class 255 [ 374.023153] tm6000: alt 3, interface 0, class 255 [ 374.023158] tm6000: New video device @ 480 Mbps (2040:6600, ifnum 0) [ 374.023162] tm6000: Found Hauppauge HVR-900H [ 374.884058] Error -32 while retrieving board version [ 375.184050] tm6000 #0: i2c eeprom 00: 01 59 54 45 12 01 00 02 00 00 00 40 40 20 00 66 .YTE.......@@ .f [ 375.380112] tm6000 #0: i2c eeprom 10: 69 00 10 20 40 01 02 03 48 00 79 00 62 00 72 00 i.. @...H.y.b.r. [ 375.572058] tm6000 #0: i2c eeprom 20: ff 00 64 ff ff ff ff ff ff ff ff ff ff ff ff ff ..d............. [ 375.764038] tm6000 #0: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 375.956103] tm6000 #0: i2c eeprom 40: 10 03 48 00 56 00 52 00 39 00 30 00 30 00 48 00 ..H.V.R.9.0.0.H. [ 376.148062] tm6000 #0: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 376.344055] tm6000 #0: i2c eeprom 60: 30 ff ff ff 0f ff ff ff ff ff 0a 03 32 00 2e 00 0...........2... [ 376.536039] tm6000 #0: i2c eeprom 70: 3f 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ?............... [ 376.728041] tm6000 #0: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 376.920041] tm6000 #0: i2c eeprom 90: 35 ff ff ff 16 03 34 00 30 00 33 00 32 00 31 00 5.....4.0.3.2.1. [ 377.112039] tm6000 #0: i2c eeprom a0: 33 00 35 00 33 00 39 00 39 00 00 00 00 00 ff ff 3.5.3.9.9....... [ 377.308054] tm6000 #0: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 377.500046] tm6000 #0: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 377.692053] tm6000 #0: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 377.885037] tm6000 #0: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 378.076042] tm6000 #0: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 378.260374] ................ [ 378.260531] Trident TVMaster TM5600/TM6000 USB2 board (Load status: 0) [ 378.320709] Hack: enabling device at addr 0xc2 [ 378.320722] tuner' 0-0061: chip found @ 0xc2 (tm6000 #0) [ 378.362555] xc2028 0-0061: creating new instance [ 378.362566] xc2028 0-0061: type set to XCeive xc2028/xc3028 tuner [ 378.362817] Setting firmware parameters for xc2028 [ 378.362834] firmware: requesting xc3028L-v36.fw [ 378.395756] xc2028 0-0061: Loading 81 firmware images from xc3028L-v36.fw, type: xc2028 firmware, ver 3.6 [ 378.692036] xc2028 0-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
The device itself does not show any affection (LEDs stay dark), there is no directory /dev/dvb created and MeTV tells me it's not finding any reciever.
What am I missing? Did I oversee anything conserning the driver-compilation? Or am I using the wrong firmware?
Comments appreciated,
David
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
WinTV HVR-1800 analog Satus
Any update on the status of analouge for this card? I really would like to switch back to Linux as my mce solution, but last time I did, the analouge was terrible, and I was getting no answers on the list...
Thanks,
Dustin Coates
Sent from my iPhone
Quoted 138 lines · David Woitkowski
Hi out there
I'm in the unfortunate position of having bought a 900H instead of a 900 and now I'm fiddling with the driver.
Details:
$ lsusb | grep Hauppauge Bus 008 Device 004: ID 2040:6600 HauppaugeMy machine is running Ubuntu 8.10 with a 2.6.27-11-generic kernel. The correct kernel-headers are installed.
As far as I've read there is (limited) support for the device with the tm6010 driver. Putting together some info from the web I did the following:
$ hg clone http://linuxtv.org/hg/v4l-dvb $ cd v4l-dvb $ hg pull -u http://linuxtv.org/hg/~mchehab/tm6010Inserted into v4l-dvb/v4l/.config three lines:
CONFIG_VIDEO_TM6000_ALSA=mCONFIG_VIDEO_TM6000=mCONFIG_VIDEO_TM6000_DVB=m$ hg merge $ makeand as root:
# make installThis far everything worked without error.
Then I got the Firmware the card was requesting in the dmesg-output from
http://steventoth.net/linux/hvr1400/xc3028L-v36.fw and copied it to /lib /firmwareSince there is no Module tm6000 I did
# modprobe -v tm6000 insmod /lib/modules/2.6.27-11-generic/kernel/drivers/media/video/videobuf-core.ko insmod /lib/modules/2.6.27-11-generic/kernel/drivers/media/video/videobuf-vmalloc.koinsmod
/lib/modules/2.6.27-11-generic/kernel/drivers/i2c/i2c-core.koinsmod/lib/modules/2.6.27-11-generic/kernel/drivers/media/video/tm6000/tm6000.ko$ dmesg [ 187.646908] tm6000 v4l2 driver version 0.0.1 loaded [ 187.647898] usbcore: registered new interface driver tm6000(tail
/var/log/messagesgives the same info)Now - as I hope the module is loaded correctly - I attacht the USB-Device:
$ dmesg [ 373.881042] usb 8-1: new high speed USB device using ehci_hcd and address 3 [ 374.019648] usb 8-1: configuration #1 chosen from 1 choice [ 374.023090] tm6000: alt 0, interface 0, class 255 [ 374.023102] tm6000: alt 0, interface 0, class 255 [ 374.023107] tm6000: Bulk IN endpoint: 0x82 (max size=512 bytes) [ 374.023111] tm6000: alt 0, interface 0, class 255 [ 374.023116] tm6000: alt 1, interface 0, class 255 [ 374.023120] tm6000: ISOC IN endpoint: 0x81 (max size=3072 bytes) [ 374.023125] tm6000: alt 1, interface 0, class 255 [ 374.023129] tm6000: alt 1, interface 0, class 255 [ 374.023133] tm6000: alt 2, interface 0, class 255 [ 374.023137] tm6000: alt 2, interface 0, class 255 [ 374.023141] tm6000: alt 2, interface 0, class 255 [ 374.023145] tm6000: alt 3, interface 0, class 255 [ 374.023149] tm6000: alt 3, interface 0, class 255 [ 374.023153] tm6000: alt 3, interface 0, class 255 [ 374.023158] tm6000: New video device @ 480 Mbps (2040:6600, ifnum 0) [ 374.023162] tm6000: Found Hauppauge HVR-900H [ 374.884058] Error -32 while retrieving board version [ 375.184050] tm6000 #0: i2c eeprom 00: 01 59 54 45 12 01 00 02 00 00 00 40 40 20 00 66 .YTE.......@@ .f [ 375.380112] tm6000 #0: i2c eeprom 10: 69 00 10 20 40 01 02 03 48 00 79 00 62 00 72 00 i.. @...H.y.b.r. [ 375.572058] tm6000 #0: i2c eeprom 20: ff 00 64 ff ff ff ff ff ff ff ff ff ff ff ff ff ..d............. [ 375.764038] tm6000 #0: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 375.956103] tm6000 #0: i2c eeprom 40: 10 03 48 00 56 00 52 00 39 00 30 00 30 00 48 00 ..H.V.R.9.0.0.H. [ 376.148062] tm6000 #0: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 376.344055] tm6000 #0: i2c eeprom 60: 30 ff ff ff 0f ff ff ff ff ff 0a 03 32 00 2e 00 0...........2... [ 376.536039] tm6000 #0: i2c eeprom 70: 3f 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ?............... [ 376.728041] tm6000 #0: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 376.920041] tm6000 #0: i2c eeprom 90: 35 ff ff ff 16 03 34 00 30 00 33 00 32 00 31 00 5.....4.0.3.2.1. [ 377.112039] tm6000 #0: i2c eeprom a0: 33 00 35 00 33 00 39 00 39 00 00 00 00 00 ff ff 3.5.3.9.9....... [ 377.308054] tm6000 #0: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 377.500046] tm6000 #0: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 377.692053] tm6000 #0: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 377.885037] tm6000 #0: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 378.076042] tm6000 #0: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 378.260374] ................ [ 378.260531] Trident TVMaster TM5600/TM6000 USB2 board (Load status: 0) [ 378.320709] Hack: enabling device at addr 0xc2 [ 378.320722] tuner' 0-0061: chip found @ 0xc2 (tm6000 #0) [ 378.362555] xc2028 0-0061: creating new instance [ 378.362566] xc2028 0-0061: type set to XCeive xc2028/xc3028 tuner [ 378.362817] Setting firmware parameters for xc2028 [ 378.362834] firmware: requesting xc3028L-v36.fw [ 378.395756] xc2028 0-0061: Loading 81 firmware images from xc3028L-v36.fw, type: xc2028 firmware, ver 3.6 [ 378.692036] xc2028 0-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.The device itself does not show any affection (LEDs stay dark), there is no directory
/dev/dvbcreated and MeTV tells me it's not finding any reciever.What am I missing? Did I oversee anything conserning the driver-compilation? Or am I using the wrong firmware?
Comments appreciated,
David_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Re: [linux-dvb] WinTV HVR-1800 analog Satus
Quoted 1 line · Dustin Coates
Any update on the status of analouge for this card? I really would like to switch back to Linux as my mce solution, but last time I did, the analouge was terrible, and I was getting no answers on the list...
Last I checked it worked fine for me.
- Steve
Re: [linux-dvb] WinTV HVR-1800 analog Satus
Quoted 7 lines · Steven Toth
Quoted 2 lines · Dustin Coates
Any update on the status of analouge for this card? I really would like to switch back to Linux as my mce solution, but last time I did, the analouge was terrible, and I was getting no answers on the list...
Last I checked it worked fine for me.
Quoted 9 lines
- Steve
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
not working here either...works very occasionally:
[19004.286089] tuner' 4-0042: chip found @ 0x84 (cx23885[0]) [19004.321897] tda829x 4-0042: could not clearly identify tuner address, defaulting to 60 [19004.379168] tda18271 4-0060: creating new instance [19004.413360] TDA18271HD/C1 detected @ 4-0060 [19005.580369] tda829x 4-0042: type set to tda8295+18271 [19828.639583] Firmware and/or mailbox pointer not initialized or corrupted, signature = 0x7bfeffff, cmd = STOP_CAPTURE [19829.749376] Firmware and/or mailbox pointer not initialized or corrupted, signature = 0x7bfeffff, cmd = PING_FW [19829.749445] firmware: requesting v4l-cx23885-enc.fw [19926.468016] ERROR: API Mailbox timeout [19927.540420] ERROR: Mailbox appears to be in use (3), cmd = PING_FW [19927.540487] firmware: requesting v4l-cx23885-enc.fw [20011.373363] tda18271_calc_bp_filter: error -34 on line 567 [20011.600033] tda18271_calc_km: error -34 on line 584 [20011.637355] tda18271_calc_rf_band: error -34 on line 601 [20011.637365] tda18271_calc_gain_taper: error -34 on line 618 [20012.076367] tda18271_calc_ir_measure: error -34 on line 635 [20012.076376] tda18271_calc_bp_filter: error -34 on line 567 [20012.076380] tda18271_calc_rf_band: error -34 on line 601 [20012.076385] tda18271_calc_gain_taper: error -34 on line 618 [20013.681363] tda18271_calc_bp_filter: error -34 on line 567 [20013.908029] tda18271_calc_km: error -34 on line 584 [20013.944363] tda18271_calc_rf_band: error -34 on line 601 [20013.944373] tda18271_calc_gain_taper: error -34 on line 618 [20014.384363] tda18271_calc_ir_measure: error -34 on line 635 [20014.384372] tda18271_calc_bp_filter: error -34 on line 567 [20014.384376] tda18271_calc_rf_band: error -34 on line 601 [20014.384381] tda18271_calc_gain_taper: error -34 on line 618 [20015.984374] tda18271_calc_bp_filter: error -34 on line 567 [20016.212029] tda18271_calc_km: error -34 on line 584 [20016.248369] tda18271_calc_rf_band: error -34 on line 601 [20016.248379] tda18271_calc_gain_taper: error -34 on line 618 [20016.688363] tda18271_calc_ir_measure: error -34 on line 635 [20016.688372] tda18271_calc_bp_filter: error -34 on line 567 [20016.688376] tda18271_calc_rf_band: error -34 on line 601 [20016.688380] tda18271_calc_gain_taper: error -34 on line 618 [20018.289362] tda18271_calc_bp_filter: error -34 on line 567 [20018.516033] tda18271_calc_km: error -34 on line 584 [20018.553355] tda18271_calc_rf_band: error -34 on line 601 [20018.553364] tda18271_calc_gain_taper: error -34 on line 618 [20018.992373] tda18271_calc_ir_measure: error -34 on line 635 [20018.992381] tda18271_calc_bp_filter: error -34 on line 567 [20018.992386] tda18271_calc_rf_band: error -34 on line 601 [20018.992392] tda18271_calc_gain_taper: error -34 on line 618