Skip to contentSkip to conversation

No subsystem id (and therefore no cx88_dvb loaded) after reboot

DISCUSSION Grant Gardner 2 participants 3 messages Mar 17, 2009 – Mar 18, 2009 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

I'm looking for some pointers on debugging a problem with my DVICO

FusionHDTV Hybrid DVB-T card.

The device was working perfectly prior to a reconfiguration of my machine,

kernel upgrade etc...

Now, on a cold start everything seems to start smoothly but I can't tune

channels.

Then, after a reboot the device is not detected due to "invalid subsystem

id". As below lspci reports no subsystem information at all.

Comparing the lspci output seems to be around the "Region 0: Memory at

ee000000 v de000000", but I'm not

sure what this means, and whether fixing the reboot problem will fix the

channel tuning problem.

Running mythbuntu 8.10

2.6.27-11-generic #1 SMP Thu Jan 29 19:28:32 UTC 2009 x86_64 GNU/Linux

lspci -vvnn after cold start

00:0a.0 Multimedia video controller [0400]: Conexant Systems, Inc.

CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)

Subsystem: DViCO Corporation Device [18ac:db40]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-

Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort- >SERR- <PERR- INTx-

Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes

Interrupt: pin A routed to IRQ 18

Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]

Capabilities: [44] Vital Product Data <?>

Capabilities: [4c] Power Management version 2

Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)

Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Kernel driver in use: cx8800

Kernel modules: cx8800

00:0a.1 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3

PCI Video and Audio Decoder [Audio Port] [14f1:8811] (rev 05)

Subsystem: DViCO Corporation Device [18ac:db40]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-

Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort- >SERR- <PERR- INTx-

Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 32 bytes

Interrupt: pin A routed to IRQ 11

Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=16M]

Capabilities: [4c] Power Management version 2

Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)

Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Kernel modules: cx88-alsa

00:0a.2 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3

PCI Video and Audio Decoder [MPEG Port] [14f1:8802] (rev 05)

Subsystem: DViCO Corporation Device [18ac:db40]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-

Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort- >SERR- <PERR- INTx-

Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes

Interrupt: pin A routed to IRQ 18

Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]

Capabilities: [4c] Power Management version 2

Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)

Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Kernel driver in use: cx88-mpeg driver manager

Kernel modules: cx8802

lspci -vvnn after warm reboot

00:0a.0 Multimedia video controller [0400]: Conexant Systems, Inc.

CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-

Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes

Interrupt: pin A routed to IRQ 18

Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=16M]

Capabilities: [44] Vital Product Data <?>

Capabilities: [4c] Power Management version 2

Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)

Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Kernel driver in use: cx8800

Kernel modules: cx8800

#1 lore raw

I experience similar problem with HVR4000 Lite cards that we have in the lab. The card can't tune after cold boot, but a reboot will fix the problem. I will check whether it has the similar invalid subsystem id problem.

Quoted 99 lines · Grant Gardner

I'm looking for some pointers on debugging a problem with my DVICO FusionHDTV Hybrid DVB-T card.

The device was working perfectly prior to a reconfiguration of my machine, kernel upgrade etc...

Now, on a cold start everything seems to start smoothly but I can't tune channels.

Then, after a reboot the device is not detected due to "invalid subsystem id". As below lspci reports no subsystem information at all.

Comparing the lspci output seems to be around the "Region 0: Memory at ee000000 v de000000", but I'm not
sure what this means, and whether fixing the reboot problem will fix the channel tuning problem.

Running mythbuntu 8.10
2.6.27-11-generic #1 SMP Thu Jan 29 19:28:32 UTC 2009 x86_64 GNU/Linux

lspci -vvnn after cold start

00:0a.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
Subsystem: DViCO Corporation Device [18ac:db40]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800

00:0a.1 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8811] (rev 05)
Subsystem: DViCO Corporation Device [18ac:db40]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: cx88-alsa

00:0a.2 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] [14f1:8802] (rev 05)
Subsystem: DViCO Corporation Device [18ac:db40]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802

lspci -vvnn after warm reboot

00:0a.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw
Quoted 1 line · Ang Way Chuang

I experience similar problem with HVR4000 Lite cards that we have in the lab. The card can't tune after cold boot, but a reboot will fix the problem. I will check whether it has the similar invalid subsystem id problem.

Unfortunately, I can't reproduce the cold boot tuning problem now. We'll send syslog information if our partner universities report the similar issue. Sorry.

Quoted 61 lines
Quoted 59 lines · Grant Gardner

I'm looking for some pointers on debugging a problem with my DVICO FusionHDTV Hybrid DVB-T card.

The device was working perfectly prior to a reconfiguration of my machine, kernel upgrade etc...

Now, on a cold start everything seems to start smoothly but I can't tune channels.

Then, after a reboot the device is not detected due to "invalid subsystem id". As below lspci reports no subsystem information at all. Comparing the lspci output seems to be around the "Region 0: Memory at ee000000 v de000000", but I'm not
sure what this means, and whether fixing the reboot problem will fix the channel tuning problem.

Running mythbuntu 8.10
2.6.27-11-generic #1 SMP Thu Jan 29 19:28:32 UTC 2009 x86_64 GNU/Linux

lspci -vvnn after cold start

00:0a.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
Subsystem: DViCO Corporation Device [18ac:db40]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800

00:0a.1 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8811] (rev 05)
Subsystem: DViCO Corporation Device [18ac:db40]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: cx88-alsa

Quoted 14 lines
Quoted 6 lines

00:0a.2 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] [14f1:8802] (rev 05)
Subsystem: DViCO Corporation Device [18ac:db40]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-

Quoted 8 lines

<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)

currently, though we're working on a commercial implementation of the RTP profile.

If you're interested in the GPL'ed UDP profile code, we can email it to you in a week or two (we'll eventually make it available on our website as well, but currently it needs to be cleaned up a bit).

T.C.

Quoted 34 lines
Quoted 28 lines

Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88-mpeg driver manager Kernel modules: cx8802

lspci -vvnn after warm reboot

00:0a.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800

Signature · 3 lines
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Signature · 3 lines
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html