no video device
Hi, dvb professionals,
I followed the advices on
http://www.linuxtv.org/wiki/index.php/How_to_Obtain%2C_Build_and_Install_V4L-DVB_Device_Drivers#Optional_Pre-Compilation_Steps
Build and Installation Instructions
downloaded the v4l sources via mercurial,
"make" and "sudo make install" finished without error messages.
rebooted the computer
dmesg shows the device:
---
usb 2-1: new high speed USB device using ehci_hcd and address 6 usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: New USB device found, idVendor=0b48, idProduct=300d usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: TT-USB2.0
usb 2-1: Manufacturer: TechnoTrend
usb 2-1: SerialNumber: LHKAMG
---
no error if I unplug and plug it on USB again
the connected box is a TechnoTrend CT 3560 CI
I googled and found chipset names like TDA8274 + TDA10023 did not find anything in wiki, so I could not determine module or driver names to be identified with lsmod.
there is no created /dev/dvb or /dev/video device
google did not help me answering the question "do I need firmware, and if so where to get it"
uname -a shows
Linux rolf9 2.6.28-7.slh.6-sidux-686 #1 SMP PREEMPT Sat Mar 14 02:30:40 UTC 2009 i686 GNU/Linux
for now I got stuck.
Do you know of a next step towards having tv on my laptop?
Rolf
Quoted 36 lines · Rolf Schumacher
Hi, dvb professionals,
I followed the advices on
http://www.linuxtv.org/wiki/index.php/How_to_Obtain%2C_Build_and_Install_V4L-DVB_Device_Drivers#Optional_Pre-Compilation_StepsBuild and Installation Instructions
downloaded the v4l sources via mercurial,
"make" and "sudo make install" finished without error messages.rebooted the computer
dmesg shows the device:
---
usb 2-1: new high speed USB device usingehci_hcdand address 6 usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: New USB device found, idVendor=0b48, idProduct=300d usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: TT-USB2.0
usb 2-1: Manufacturer: TechnoTrend
usb 2-1: SerialNumber: LHKAMG
---no error if I unplug and plug it on USB again
the connected box is a TechnoTrend CT 3560 CI
I googled and found chipset names like TDA8274 + TDA10023 did not find anything in wiki, so I could not determine module or driver names to be identified with lsmod.there is no created
/dev/dvbor/dev/videodevicegoogle did not help me answering the question "do I need firmware, and if so where to get it"
Quoted 7 lines
uname -a shows
Linux rolf9 2.6.28-7.slh.6-sidux-686 #1 SMP PREEMPT Sat Mar 14 02:30:40 UTC 2009 i686 GNU/Linuxfor now I got stuck.
Do you know of a next step towards having tv on my laptop?
I don't think the product is supported. Just to be clear, you can't just modprobe the chip driver for whatever components happen to be in your device and expect it to work.
If you are lucky enough to have a product where all the chipset drivers are already written, then a developer needs to write a device profile in the bridge driver. However, if it uses some components that are not supported, then it's a lot more work since an entire new driver needs to be written.
If you want to help make it work, you should start by creating a page in the linuxtv.org wiki, and include high resolution digital photos of the circuit board, so people can get an accurate inventory of what chips are in the device in question. From there, perhaps a developer interested in adding the support can do the driver work.
Cheers,
Devin
Signature · 3 lines
Devin J. Heitmueller http://www.devinheitmueller.com AIM: devinheitmueller