Skip to contentSkip to conversation

OMAP3: Pending patches

U-Boot Applied Dirk Behme 3 participants 9 messages Apr 24, 2009 – May 1, 2009

lore
Share & tools
lore

Dirk Behme

author
#0 lore raw

To avoid loosing the overview, here my list of pending OMAP3 patches ready to be applied. From my point of view there are no open comments on these which will prevent to apply them. But please correct if I overlooked anything or add what (patches? comments?) I missed.

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

7. Zoom2 respin II (10 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/050863.html
http://lists.denx.de/pipermail/u-boot/2009-April/050864.html
http://lists.denx.de/pipermail/u-boot/2009-April/050865.html
http://lists.denx.de/pipermail/u-boot/2009-April/050866.html
http://lists.denx.de/pipermail/u-boot/2009-April/050868.html
http://lists.denx.de/pipermail/u-boot/2009-April/050867.html
http://lists.denx.de/pipermail/u-boot/2009-April/050869.html
http://lists.denx.de/pipermail/u-boot/2009-April/050870.html
http://lists.denx.de/pipermail/u-boot/2009-April/050871.html
http://lists.denx.de/pipermail/u-boot/2009-April/050872.html

Note: There might be some dependencies between some of these patches. Different authors, sent at different time, unfortunately this can't be avoided. So dependent on the order the patches will be applied, there might be some conflicts. Let us know them, we will try to update/fix then as soon as possible! Most probably 5. and 7. will have some conflicts, as 5. removes some code 7. assumes it is still there. If this results in a conflict, let us apply the 10 patches from 7. first and then update 5.

Many thanks and best regards

Dirk

author
#1 lore raw

Short status update after scanning the recent mails:

Quoted 12 lines · Dirk Behme

To avoid loosing the overview, here my list of pending OMAP3 patches ready to be applied. From my point of view there are no open comments on these which will prevent to apply them. But please correct if I overlooked anything or add what (patches? comments?) I missed.

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Quoted 8 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

We will try to switch to

print_cpuinfo & checkboard

http://lists.denx.de/pipermail/u-boot/2009-April/051365.html

Premi: Do you like to have a look? Hopefully it wouldn't be too hard.

Jean-Christophe: Please fix the "test-only" and add the documentation as requested by Wolfgang as soon as possible, that we can safely use it.

http://lists.denx.de/pipermail/u-boot/2009-April/051382.html

Quoted 14 lines

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

7. Zoom2 respin II (10 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/050863.html
http://lists.denx.de/pipermail/u-boot/2009-April/050864.html
http://lists.denx.de/pipermail/u-boot/2009-April/050865.html
http://lists.denx.de/pipermail/u-boot/2009-April/050866.html
http://lists.denx.de/pipermail/u-boot/2009-April/050868.html
http://lists.denx.de/pipermail/u-boot/2009-April/050867.html
http://lists.denx.de/pipermail/u-boot/2009-April/050869.html
http://lists.denx.de/pipermail/u-boot/2009-April/050870.html
http://lists.denx.de/pipermail/u-boot/2009-April/050871.html
http://lists.denx.de/pipermail/u-boot/2009-April/050872.html

After

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html
http://lists.denx.de/pipermail/u-boot/2009-April/051384.html
http://lists.denx.de/pipermail/u-boot/2009-April/051385.html
http://lists.denx.de/pipermail/u-boot/2009-April/051386.html

Tom has to check if an update of this series is necessary.

Quoted 8 lines

Note: There might be some dependencies between some of these patches. Different authors, sent at different time, unfortunately this can't be avoided. So dependent on the order the patches will be applied, there might be some conflicts. Let us know them, we will try to update/fix then as soon as possible! Most probably 5. and 7. will have some conflicts, as 5. removes some code 7. assumes it is still there. If this results in a conflict, let us apply the 10 patches from 7. first and then update 5.

Jean-Christophe: If series 7. needs an update, it would be really helpful if you could apply the other patches so that updated 7. can be rebased against them. This will reduce the risk of conflicts.

Dirk

#2 lore raw
Quoted 35 lines

-----Original Message-----
From: Dirk Behme [mailto:dirk.behme at googlemail.com]
Sent: Saturday, April 25, 2009 11:05 AM
To: U-Boot user list; Jean-Christophe PLAGNIOL-VILLARD; Premi, Sanjeev; Tom Rix
Cc: Wolfgang Denk
Subject: Re: OMAP3: Pending patches

Short status update after scanning the recent mails:

Quoted 2 lines · Dirk Behme

To avoid loosing the overview, here my list of pending

OMAP3 patches

Quoted 1 line

ready to be applied. From my point of view there are no

open comments on

Quoted 9 lines

these which will prevent to apply them. But please correct if I overlooked anything or add what (patches? comments?) I missed.

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Quoted 8 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

Quoted 7 lines

We will try to switch to

print_cpuinfo & checkboard

http://lists.denx.de/pipermail/u-boot/2009-April/051365.html

Premi: Do you like to have a look? Hopefully it wouldn't be too hard.

[SP] Sure, I will...

Quoted 54 lines

Jean-Christophe: Please fix the "test-only" and add the documentation as requested by Wolfgang as soon as possible, that we can safely use it.

http://lists.denx.de/pipermail/u-boot/2009-April/051382.html

Quoted 14 lines

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

7. Zoom2 respin II (10 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/050863.html
http://lists.denx.de/pipermail/u-boot/2009-April/050864.html
http://lists.denx.de/pipermail/u-boot/2009-April/050865.html
http://lists.denx.de/pipermail/u-boot/2009-April/050866.html
http://lists.denx.de/pipermail/u-boot/2009-April/050868.html
http://lists.denx.de/pipermail/u-boot/2009-April/050867.html
http://lists.denx.de/pipermail/u-boot/2009-April/050869.html
http://lists.denx.de/pipermail/u-boot/2009-April/050870.html
http://lists.denx.de/pipermail/u-boot/2009-April/050871.html
http://lists.denx.de/pipermail/u-boot/2009-April/050872.html

After

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html
http://lists.denx.de/pipermail/u-boot/2009-April/051384.html
http://lists.denx.de/pipermail/u-boot/2009-April/051385.html
http://lists.denx.de/pipermail/u-boot/2009-April/051386.html

Tom has to check if an update of this series is necessary.

Quoted 1 line

Note: There might be some dependencies between some of

these patches.

Quoted 1 line

Different authors, sent at different time, unfortunately

this can't be

Quoted 1 line

avoided. So dependent on the order the patches will be

applied, there

Quoted 1 line

might be some conflicts. Let us know them, we will try to

update/fix

Quoted 2 lines

then as soon as possible! Most probably 5. and 7. will have some conflicts, as 5. removes some code 7. assumes it is still

there. If this

Quoted 1 line

results in a conflict, let us apply the 10 patches from 7.

first and

Quoted 1 line

then update 5.

Jean-Christophe: If series 7. needs an update, it would be really helpful if you could apply the other patches so that updated
7. can be
rebased against them. This will reduce the risk of conflicts.

Dirk

author
#3 lore raw
In reply to Dirk Behme

Short status update after recent merges and patch updates. As usual, please correct if anything is wrong or missing.

Quoted 8 lines · Dirk Behme

To avoid loosing the overview, here my list of pending OMAP3 patches ready to be applied. From my point of view there are no open comments on these which will prevent to apply them. But please correct if I overlooked anything or add what (patches? comments?) I missed.

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

Mail

http://lists.denx.de/pipermail/u-boot/2009-April/051459.html

tells us that this should be applied to u-boot-arm next. But I can't find it in gitweb

http://git.denx.de/?p=u-boot/u-boot-arm.git;a=shortlog;h=refs/heads/next

Did I miss something?

Btw.: As initial patch and first update was sent ~1 day after merge window close (Apr 4?) I hoped to have a chance to still get it into master ;(

Quoted 2 lines

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

Quoted 5 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

Applied to u-boot-arm master.

Quoted 5 lines

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

Patches 5 & 6 replaced by update which includes switch to checkboard and print_cpuinfo:

OMAP3: Board specific updates (3 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/051505.html
http://lists.denx.de/pipermail/u-boot/2009-April/051506.html
http://lists.denx.de/pipermail/u-boot/2009-April/051507.html

Quoted 1 line

7. Zoom2 respin II (10 patches)

Note: Initial patch series for this was sent 'Wed Apr 1 18:08:38 CEST 2009'

http://lists.denx.de/pipermail/u-boot/2009-April/050094.html

IMHO this was while open merge window.

Quoted 6 lines

http://lists.denx.de/pipermail/u-boot/2009-April/050863.html
http://lists.denx.de/pipermail/u-boot/2009-April/050864.html
http://lists.denx.de/pipermail/u-boot/2009-April/050865.html
http://lists.denx.de/pipermail/u-boot/2009-April/050866.html
http://lists.denx.de/pipermail/u-boot/2009-April/050868.html
http://lists.denx.de/pipermail/u-boot/2009-April/050867.html

Applied to u-boot-arm next (see comment about merge window above).

Quoted 1 line

http://lists.denx.de/pipermail/u-boot/2009-April/050869.html

Applied to u-boot-arm next (see comment about merge window above).

Quoted 2 lines

http://lists.denx.de/pipermail/u-boot/2009-April/050870.html
http://lists.denx.de/pipermail/u-boot/2009-April/050871.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

Quoted 1 line

http://lists.denx.de/pipermail/u-boot/2009-April/050872.html

For the rest of the Zoom2 patches (#1, #2, #3, #4, #5, #8 & #10)

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html
http://lists.denx.de/pipermail/u-boot/2009-April/051384.html
http://lists.denx.de/pipermail/u-boot/2009-April/051385.html
http://lists.denx.de/pipermail/u-boot/2009-April/051386.html
http://lists.denx.de/pipermail/u-boot/2009-April/051455.html

seem to apply.

Quoted 14 lines

Note: There might be some dependencies between some of these patches. Different authors, sent at different time, unfortunately this can't be avoided. So dependent on the order the patches will be applied, there might be some conflicts. Let us know them, we will try to update/fix then as soon as possible! Most probably 5. and 7. will have some conflicts, as 5. removes some code 7. assumes it is still there. If this results in a conflict, let us apply the 10 patches from 7. first and then update 5.

Many thanks and best regards

Dirk

#4 lore raw

Dear Dirk,

Quoted 3 lines · In message <[email protected]> you wrote:

Short status update after recent merges and patch updates. As usual, please correct if anything is wrong or missing.

Thanks for the summary.

Quoted 12 lines
Quoted 8 lines · Dirk Behme

To avoid loosing the overview, here my list of pending OMAP3 patches ready to be applied. From my point of view there are no open comments on these which will prevent to apply them. But please correct if I overlooked anything or add what (patches? comments?) I missed.

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

Mail

Quoted 8 lines

http://lists.denx.de/pipermail/u-boot/2009-April/051459.html

tells us that this should be applied to u-boot-arm next. But I can't find it in gitweb

http://git.denx.de/?p=u-boot/u-boot-arm.git;a=shortlog;h=refs/heads/next

Did I miss something?

I cannot find it either.

Quoted 3 lines

Btw.: As initial patch and first update was sent ~1 day after merge window close (Apr 4?) I hoped to have a chance to still get it into master ;(

We don't have to bend much to consider this even a bug fix (it fixes a specific board configuration, doesn't it?).

Quoted 45 lines
Quoted 2 lines

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

Quoted 5 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

Applied to u-boot-arm master.

Quoted 5 lines

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

Patches 5 & 6 replaced by update which includes switch to checkboard and print_cpuinfo:

OMAP3: Board specific updates (3 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/051505.html
http://lists.denx.de/pipermail/u-boot/2009-April/051506.html
http://lists.denx.de/pipermail/u-boot/2009-April/051507.html

Quoted 1 line

7. Zoom2 respin II (10 patches)

Note: Initial patch series for this was sent 'Wed Apr 1 18:08:38 CEST 2009'

http://lists.denx.de/pipermail/u-boot/2009-April/050094.html

IMHO this was while open merge window.

Quoted 6 lines

http://lists.denx.de/pipermail/u-boot/2009-April/050863.html
http://lists.denx.de/pipermail/u-boot/2009-April/050864.html
http://lists.denx.de/pipermail/u-boot/2009-April/050865.html
http://lists.denx.de/pipermail/u-boot/2009-April/050866.html
http://lists.denx.de/pipermail/u-boot/2009-April/050868.html
http://lists.denx.de/pipermail/u-boot/2009-April/050867.html

Applied to u-boot-arm next (see comment about merge window above).

Quoted 8 lines
Quoted 1 line

http://lists.denx.de/pipermail/u-boot/2009-April/050869.html

Applied to u-boot-arm next (see comment about merge window above).

Quoted 2 lines

http://lists.denx.de/pipermail/u-boot/2009-April/050870.html
http://lists.denx.de/pipermail/u-boot/2009-April/050871.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

I think all the patches listed above could and should go into master now.

Jean-Cristophe, what do you think? Do you have any specific reasons for not pulling these into master now?

Quoted 11 lines
Quoted 1 line

http://lists.denx.de/pipermail/u-boot/2009-April/050872.html

For the rest of the Zoom2 patches (#1, #2, #3, #4, #5, #8 & #10)

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html
http://lists.denx.de/pipermail/u-boot/2009-April/051384.html
http://lists.denx.de/pipermail/u-boot/2009-April/051385.html
http://lists.denx.de/pipermail/u-boot/2009-April/051386.html
http://lists.denx.de/pipermail/u-boot/2009-April/051455.html

seem to apply.

I'm not sure what you mean here, Dirk. I understand that Jean-Cristophe requested changes, and we're waiting for a resubmit, right?

Jean-Cristophe, I really would like to see some progress in this area, so I'd appreciate if you could apply the patches listed above to master and send me a pull request. Thanks.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Brain off-line, please wait.
author
#5 lore raw

Dear Wolfgang,

Quoted 20 lines · Wolfgang Denk

Dear Dirk,

Quoted 2 lines · In message <[email protected]> you wrote:

Short status update after recent merges and patch updates. As usual, please correct if anything is wrong or missing.

Thanks for the summary.

Quoted 12 lines
Quoted 7 lines · Dirk Behme

To avoid loosing the overview, here my list of pending OMAP3 patches ready to be applied. From my point of view there are no open comments on these which will prevent to apply them. But please correct if I overlooked anything or add what (patches? comments?) I missed.

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

Mail

http://lists.denx.de/pipermail/u-boot/2009-April/051459.html

Quoted 8 lines
Quoted 6 lines

tells us that this should be applied to u-boot-arm next. But I can't find it in gitweb

http://git.denx.de/?p=u-boot/u-boot-arm.git;a=shortlog;h=refs/heads/next

Did I miss something?

I cannot find it either.

:(

Quoted 6 lines
Quoted 3 lines

Btw.: As initial patch and first update was sent ~1 day after merge window close (Apr 4?) I hoped to have a chance to still get it into master ;(

We don't have to bend much to consider this even a bug fix (it fixes a specific board configuration, doesn't it?).

Yes. We got a new board HW revision ('revision C', with some re-wiring) which needs some minor changes in PinMux to support this changed wiring. Thanks to a HW identification (resistors on GPIOs) we are able to auto detect HW revision and configure correct pin mux automagically. This is done by this patch.

Quoted 63 lines
Quoted 38 lines
Quoted 2 lines

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

Quoted 5 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

Applied to u-boot-arm master.

Quoted 5 lines

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

Patches 5 & 6 replaced by update which includes switch to checkboard and print_cpuinfo:

OMAP3: Board specific updates (3 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/051505.html
http://lists.denx.de/pipermail/u-boot/2009-April/051506.html
http://lists.denx.de/pipermail/u-boot/2009-April/051507.html

Quoted 1 line

7. Zoom2 respin II (10 patches)

Note: Initial patch series for this was sent 'Wed Apr 1 18:08:38 CEST 2009'

http://lists.denx.de/pipermail/u-boot/2009-April/050094.html

IMHO this was while open merge window.

Quoted 6 lines

http://lists.denx.de/pipermail/u-boot/2009-April/050863.html
http://lists.denx.de/pipermail/u-boot/2009-April/050864.html
http://lists.denx.de/pipermail/u-boot/2009-April/050865.html
http://lists.denx.de/pipermail/u-boot/2009-April/050866.html
http://lists.denx.de/pipermail/u-boot/2009-April/050868.html
http://lists.denx.de/pipermail/u-boot/2009-April/050867.html

Quoted 8 lines

Applied to u-boot-arm next (see comment about merge window above).

Quoted 1 line

http://lists.denx.de/pipermail/u-boot/2009-April/050869.html

Applied to u-boot-arm next (see comment about merge window above).

Quoted 2 lines

http://lists.denx.de/pipermail/u-boot/2009-April/050870.html
http://lists.denx.de/pipermail/u-boot/2009-April/050871.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

I think all the patches listed above could and should go into master now.

Jean-Cristophe, what do you think? Do you have any specific reasons for not pulling these into master now?

Quoted 9 lines
Quoted 1 line

http://lists.denx.de/pipermail/u-boot/2009-April/050872.html

For the rest of the Zoom2 patches (#1, #2, #3, #4, #5, #8 & #10)

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html
http://lists.denx.de/pipermail/u-boot/2009-April/051384.html
http://lists.denx.de/pipermail/u-boot/2009-April/051385.html
http://lists.denx.de/pipermail/u-boot/2009-April/051386.html
http://lists.denx.de/pipermail/u-boot/2009-April/051455.html

Quoted 3 lines
Quoted 1 line

seem to apply.

I'm not sure what you mean here, Dirk.

I tried to say that for patches #1, #2, #3, #4, #5, #8 & #10 there are comments in the 5 mails linked above (i.e. the comments in the 5 mails above apply to the patches #1, #2, #3, #4, #5, #8 & #10).

Quoted 2 lines

I understand that
Jean-Cristophe requested changes,

Yes.

Quoted 2 lines

and we're waiting for a resubmit,
right?

Well, before waiting for a resubmit, I would wait for a comment (discussion?) from the patch author (Tom).

Anyhow, seems we got a comment from Tom

http://lists.denx.de/pipermail/u-boot/2009-April/051605.html

and _now_ we are waiting for a resubmit ;)

Quoted 3 lines

Jean-Cristophe, I really would like to see some progress in this area, so I'd appreciate if you could apply the patches listed above to master and send me a pull request. Thanks.

Many thanks for helping and best regards

Dirk

author
#6 lore raw
In reply to Dirk Behme

Short status update after recent ARM pull request

http://lists.denx.de/pipermail/u-boot/2009-April/051803.html

Quoted 15 lines · Dirk Behme
Quoted 7 lines

To avoid loosing the overview, here my list of pending OMAP3 patches ready to be applied. From my point of view there are no open comments on these which will prevent to apply them. But please correct if I overlooked anything or add what (patches? comments?) I missed.

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

Mail

http://lists.denx.de/pipermail/u-boot/2009-April/051459.html

tells us that this should be applied to u-boot-arm next. But I can't find it in gitweb

Quoted 7 lines

http://git.denx.de/?p=u-boot/u-boot-arm.git;a=shortlog;h=refs/heads/next

Did I miss something?

Btw.: As initial patch and first update was sent ~1 day after merge window close (Apr 4?) I hoped to have a chance to still get it into master ;(

Applied to u-boot-arm next.

Quoted 4 lines
Quoted 2 lines

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

Copied to u-boot-arm master and part of above ARM pull request (still in u-boot-arm next, too?)

Quoted 2 lines
Quoted 2 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

Pending

http://lists.denx.de/pipermail/u-boot/2009-April/051518.html

Quoted 4 lines
Quoted 2 lines

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

Applied to u-boot-arm master.

... and part of above ARM pull request.

Quoted 6 lines
Quoted 5 lines

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

Quoted 7 lines

Patches 5 & 6 replaced by update which includes switch to checkboard and print_cpuinfo:

OMAP3: Board specific updates (3 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/051505.html
http://lists.denx.de/pipermail/u-boot/2009-April/051506.html
http://lists.denx.de/pipermail/u-boot/2009-April/051507.html

All three patches applied to u-boot-arm master and part of above pull request.

Quoted 1 line
Quoted 1 line

7. Zoom2 respin II (10 patches)

...

Recent remaining 5 Zoom2 patches

http://lists.denx.de/pipermail/u-boot/2009-April/051651.html
http://lists.denx.de/pipermail/u-boot/2009-April/051652.html
http://lists.denx.de/pipermail/u-boot/2009-April/051653.html
http://lists.denx.de/pipermail/u-boot/2009-April/051654.html
http://lists.denx.de/pipermail/u-boot/2009-April/051655.html

pending/under discussion

http://lists.denx.de/pipermail/u-boot/2009-April/051792.html

Summary:

Besides the question if "Set pinmux conditionally for Rev C boards" should go from next to master, the 5 "Zoom2" and the "OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000" are still open.

Best regards

Dirk

#7 lore raw

Dear Dirk Behme,

Quoted 2 lines · In message <[email protected]> you wrote:

Short status update after recent ARM pull request

Thanks for keeping the summary up to date. This is really helpful in this complicated situation.

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

...

Quoted 1 line

Applied to u-boot-arm next.

I cherry-picked it form there. It's in the master branch of the master repo now. [Well, give me 10 minutes until it makes it to the public server.]

Quoted 7 lines
Quoted 4 lines
Quoted 2 lines

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

Copied to u-boot-arm master and part of above ARM pull request (still in u-boot-arm next, too?)

That should not matter. git will sort this out.

Quoted 4 lines
Quoted 2 lines
Quoted 2 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

Pending

Applied to master branch in master repo now.

Quoted 18 lines

http://lists.denx.de/pipermail/u-boot/2009-April/051518.html

Quoted 4 lines
Quoted 2 lines

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

Applied to u-boot-arm master.

... and part of above ARM pull request.

Quoted 9 lines
Quoted 5 lines

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

Patches 5 & 6 replaced by update which includes switch to checkboard and print_cpuinfo:

Quoted 7 lines
Quoted 4 lines

OMAP3: Board specific updates (3 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/051505.html
http://lists.denx.de/pipermail/u-boot/2009-April/051506.html
http://lists.denx.de/pipermail/u-boot/2009-April/051507.html

All three patches applied to u-boot-arm master and part of above pull request.

So all the above is in mainline now and can be deleted from this list.

Wow. That was tough.

Quoted 13 lines
Quoted 1 line
Quoted 1 line

7. Zoom2 respin II (10 patches)

...

Recent remaining 5 Zoom2 patches

http://lists.denx.de/pipermail/u-boot/2009-April/051651.html
http://lists.denx.de/pipermail/u-boot/2009-April/051652.html
http://lists.denx.de/pipermail/u-boot/2009-April/051653.html
http://lists.denx.de/pipermail/u-boot/2009-April/051654.html
http://lists.denx.de/pipermail/u-boot/2009-April/051655.html

pending/under discussion

Quoted 7 lines

http://lists.denx.de/pipermail/u-boot/2009-April/051792.html

Summary:

Besides the question if "Set pinmux conditionally for Rev C boards" should go from next to master, the 5 "Zoom2" and the "OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000" are still open.

Well, initial version was submitted when the MW was still open, so these should go in now, unless there are requests for changes.

Let's wait until Monday, OK?

Best regards,

Wolfgang Denk

Signature · 7 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
GUIs  are  virtually  useless.  Learn  tools.  They're  configurable,
scriptable, automatable, cron-able, interoperable, etc. We don't need
no brain-dead winslurping monolithic claptrap.
                               -- Tom Christiansen in 371140df at csnews
author
#8 lore raw

Dear Wolfgang,

Quoted 51 lines · Wolfgang Denk

Dear Dirk Behme,

Quoted 1 line · In message <[email protected]> you wrote:

Short status update after recent ARM pull request

Thanks for keeping the summary up to date. This is really helpful in this complicated situation.

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards
http://lists.denx.de/pipermail/u-boot/2009-April/051013.html

...

Quoted 1 line

Applied to u-boot-arm next.

I cherry-picked it form there. It's in the master branch of the master repo now. [Well, give me 10 minutes until it makes it to the public server.]

Quoted 5 lines
Quoted 3 lines
Quoted 2 lines

2. OMAP3: Remove legacy NAND defines
http://lists.denx.de/pipermail/u-boot/2009-April/050882.html

Applied to u-boot-arm next. Request to move to master by Wolfgang.

Copied to u-boot-arm master and part of above ARM pull request (still in u-boot-arm next, too?)

That should not matter. git will sort this out.

Quoted 3 lines
Quoted 2 lines
Quoted 2 lines

3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
http://lists.denx.de/pipermail/u-boot/2009-April/051178.html

Pending

Applied to master branch in master repo now.

Quoted 19 lines

http://lists.denx.de/pipermail/u-boot/2009-April/051518.html

Quoted 3 lines
Quoted 2 lines

4. OMAP3: Fix changed mmc init command
http://lists.denx.de/pipermail/u-boot/2009-April/051179.html

Applied to u-boot-arm master.

... and part of above ARM pull request.

Quoted 12 lines
Quoted 5 lines

5. OMAP3: Remove unused board-types
http://lists.denx.de/pipermail/u-boot/2009-April/051338.html

6. OMAP3: Print correct silicon revision
http://lists.denx.de/pipermail/u-boot/2009-April/051339.html

Patches 5 & 6 replaced by update which includes switch to checkboard and print_cpuinfo:

OMAP3: Board specific updates (3 patches)
http://lists.denx.de/pipermail/u-boot/2009-April/051505.html
http://lists.denx.de/pipermail/u-boot/2009-April/051506.html
http://lists.denx.de/pipermail/u-boot/2009-April/051507.html

Quoted 6 lines
Quoted 2 lines

All three patches applied to u-boot-arm master and part of above pull request.

So all the above is in mainline now and can be deleted from this list.

Wow. That was tough.

Thank you for all your help!

Best regards

Dirk