Skip to contentSkip to conversation

Hauppauge HVR 1110 and DVB

DISCUSSION Antonio Beamud Montero 3 participants 7 messages May 19, 2009 – May 21, 2009 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

I have a new hauppauge hvr 1110. Trying to load the lastest modules, all seems to load fine, but no dvb-t frontend is created. As I can see this card isn't exactly the same hvr 1110 (hvr 1110r3) supported by v4l-dvb. The system reports the next info:

# lspci -v

0b:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
Subsystem: Hauppauge computer works Inc. Unknown device 6707
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 114
Region 0: Memory at fc4ff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-

# dmesg

ACPI: PCI Interrupt 0000:0f:03.0[A] -> GSI 160 (level, low) -> IRQ 65
saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio: 0xfc4ff800 saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3 [card=156,autodetected] saa7133[0]: board init: gpio is 40000
saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00 saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09 saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72 saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00 saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368
tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 0-0050: audio processor is SAA7131 (idx 41)
tveeprom 0-0050: decoder processor is SAA7131 (idx 35)
tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
saa7133[0]: hauppauge eeprom: model=67209
tuner 0-004b: chip found @ 0x96 (saa7133[0])
tda829x 0-004b: setting tuner address to 60
tda18271 0-0060: creating new instance
TDA18271HD/C2 detected @ 0-0060
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
tda829x 0-004b: type set to tda8290+18271
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1

Trying to load manually the saa7134-dvb module reports nothing.

The module seems to recognize the 67209LF rev C1F5 ok.

Hauppauge hvr 1110 Hardware Info:

Decoder: saa7131E/03/G
Module: TDA10048HN (http://www.ecnasiamag.com/article-10192-philipstda10048hnenablesdigitaltvviewingthroughentertainmentdevices-Asia.html)

Greetings

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#1 lore raw

Hi Antonio,

Am Dienstag, den 19.05.2009, 12:29 +0200 schrieb Antonio Beamud Montero:

Quoted 4 lines

I have a new hauppauge hvr 1110. Trying to load the lastest modules, all seems to load fine, but no dvb-t frontend is created. As I can see this card isn't exactly the same hvr 1110 (hvr 1110r3) supported by v4l-dvb. The system reports the next info:

we moved to [email protected]

Michael Krufky has added support for these new tuners and cards and Steven Toth for the tda10048.

But it is correct, DVB is not yet enabled on them.

Maybe Michael can give you some hints on what he is still working to do so and if he might call for testers once.

Cheers,
Hermann

Quoted 74 lines
# lspci -v

0b:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
Subsystem: Hauppauge computer works Inc. Unknown device 6707
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 114
Region 0: Memory at fc4ff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-

# dmesg

ACPI: PCI Interrupt 0000:0f:03.0[A] -> GSI 160 (level, low) -> IRQ 65 saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio:
0xfc4ff800
saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3 [card=156,autodetected]
saa7133[0]: board init: gpio is 40000
saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00 saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09 saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72 saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00 saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368 tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is SAA7131 (idx 41)
tveeprom 0-0050: decoder processor is SAA7131 (idx 35) tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter saa7133[0]: hauppauge eeprom: model=67209
tuner 0-004b: chip found @ 0x96 (saa7133[0])
tda829x 0-004b: setting tuner address to 60
tda18271 0-0060: creating new instance
TDA18271HD/C2 detected @ 0-0060
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
tda829x 0-004b: type set to tda8290+18271
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1

Trying to load manually the saa7134-dvb module reports nothing.

The module seems to recognize the 67209LF rev C1F5 ok.

Hauppauge hvr 1110 Hardware Info:

Decoder: saa7131E/03/G
Module: TDA10048HN
(http://www.ecnasiamag.com/article-10192-philipstda10048hnenablesdigitaltvviewingthroughentertainmentdevices-Asia.html)

Greetings

#2 lore raw
In reply to Antonio Beamud Montero
Quoted 69 lines · Antonio Beamud Montero

I have a new hauppauge hvr 1110. Trying to load the lastest modules, all seems to load fine, but no dvb-t frontend is created. As I can see this card isn't exactly the same hvr 1110 (hvr 1110r3) supported by v4l-dvb. The system reports the next info:

# lspci -v

0b:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
Subsystem: Hauppauge computer works Inc. Unknown device 6707
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 114
Region 0: Memory at fc4ff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-

# dmesg

ACPI: PCI Interrupt 0000:0f:03.0[A] -> GSI 160 (level, low) -> IRQ 65 saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio:
0xfc4ff800
saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3 [card=156,autodetected]
saa7133[0]: board init: gpio is 40000
saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00 saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09 saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72 saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00 saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368 tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is SAA7131 (idx 41)
tveeprom 0-0050: decoder processor is SAA7131 (idx 35) tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter saa7133[0]: hauppauge eeprom: model=67209
tuner 0-004b: chip found @ 0x96 (saa7133[0])
tda829x 0-004b: setting tuner address to 60
tda18271 0-0060: creating new instance
TDA18271HD/C2 detected @ 0-0060
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
tda829x 0-004b: type set to tda8290+18271
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1

Trying to load manually the saa7134-dvb module reports nothing.

Quoted 7 lines

The module seems to recognize the 67209LF rev C1F5 ok.

Hauppauge hvr 1110 Hardware Info:

Decoder: saa7131E/03/G
Module: TDA10048HN
(http://www.ecnasiamag.com/article-10192-philipstda10048hnenablesdigitaltvviewingthroughentertainmentdevices-Asia.html)

Hello,

I specifically left out the DVB support for this device.

To be honest, I didn't know that this board was available for purchase already. Where did you get it? (just curious)

I like to add card support for all products as soon as possible. In the case of this board, analog works but digital does not yet.

I'm a bit busy at the moment ... Try again in a few weeks to a month or so and there should be more progress.

If something happens sooner than that, I'll append another email to this thread.

Regards,

Mike

#3 lore raw
Quoted 9 lines · Michael Krufky

On Tue, May 19, 2009 at 6:29 AM, Antonio Beamud Montero

Hello,

I specifically left out the DVB support for this device.

To be honest, I didn't know that this board was available for purchase already. Where did you get it? (just curious)

It seems that here in spain is available :)

Quoted 3 lines

If something happens sooner than that, I'll append another email to this thread.

Ok, If you need a tester, I'm your man ;)

Thank you.

Greetings.

#4 lore raw
Quoted 19 lines · Antonio Beamud Montero
Quoted 9 lines · Michael Krufky

On Tue, May 19, 2009 at 6:29 AM, Antonio Beamud Montero Hello,

I specifically left out the DVB support for this device.

To be honest, I didn't know that this board was available for purchase already.  Where did you get it?  (just curious)

It seems that here in spain is available :)

Quoted 4 lines

If something happens sooner than that, I'll append another email to this thread.

Quoted 5 lines

Ok, If you need a tester, I'm your man ;)

Thank you.

Greetings.

(i am sending this a second time -- first message got rejected by vger)

You're in luck -- I resolved the problem today... If you'd like to test, please try out this repository:

http://kernellabs.com/hg/~mk/hvr1110

Please let me know how this works for you.

Regards,

Mike Krufky

#5 lore raw
Quoted 29 lines · Michael Krufky
Quoted 19 lines · Antonio Beamud Montero
Quoted 9 lines · Michael Krufky

On Tue, May 19, 2009 at 6:29 AM, Antonio Beamud Montero
Hello,

I specifically left out the DVB support for this device.

To be honest, I didn't know that this board was available for purchase already. Where did you get it? (just curious)

It seems that here in spain is available :)

Quoted 4 lines

If something happens sooner than that, I'll append another email to this thread.

Quoted 6 lines

Ok, If you need a tester, I'm your man ;)

Thank you.

Greetings.

Quoted 10 lines

(i am sending this a second time -- first message got rejected by vger)

You're in luck -- I resolved the problem today... If you'd like to test, please try out this repository:

http://kernellabs.com/hg/~mk/hvr1110

Please let me know how this works for you.

Thanks for the patch. Seems to load fine, the problem arises when try load the firmware.

--------
saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio: 0xfc4ff800 saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid [card=156,autodetected] saa7133[0]: board init: gpio is 440100
tuner 0-004b: chip found @ 0x96 (saa7133[0])
saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff
saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00
saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09
saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72
saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00
saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368
tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 0-0050: audio processor is SAA7131 (idx 41)
tveeprom 0-0050: decoder processor is SAA7131 (idx 35)
tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
saa7133[0]: hauppauge eeprom: model=67209
tda829x 0-004b: setting tuner address to 60
tda18271 0-0060: creating new instance
TDA18271HD/C2 detected @ 0-0060
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
tda829x 0-004b: type set to tda8290+18271
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
dvb_init() allocating 1 frontend
tda829x 0-004b: type set to tda8290
tda18271 0-0060: attaching existing instance
DVB: registering new adapter (saa7133[0])
DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)...
tda10048_firmware_upload: firmware read 24878 bytes.
tda10048_firmware_upload: firmware uploading
tda10048_firmware_upload: firmware upload failed
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1

---

I've tried to extract the firmware from the windows drivers, but all my experiments failed. How I can get the correct firmware?

Thanks for all again.

#6 lore raw
Quoted 2 lines · Antonio Beamud Montero

Thanks for the patch. Seems to load fine, the problem arises when try load the firmware.

[snip]

Quoted 10 lines

DVB: registering new adapter (saa7133[0])
DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)...
tda10048_firmware_upload: firmware read 24878 bytes.
tda10048_firmware_upload: firmware uploading
tda10048_firmware_upload: firmware upload failed
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1

Quoted 5 lines

---

I've tried to extract the firmware from the windows drivers, but all my experiments failed.
How I can get the correct firmware?

You can get the firmware from here:

http://www.steventoth.net/linux/hvr1200

Regards,

Mike