question on agcount and agsize
I've just installed xfs for the first time and I'm trying to put an xfs file system on a large disk. When I just tried with no arguments, it told me that the agsize was too large and the maximum is 268435455 blocks. I wasn't familiar with allocation groups at all so I researched this a little bit. I found out what an allocation group is but there aren't many recommendations on agcount other than "don't make it too big" because it slows the disk down as it gets full. However, after playing with the numbers, I found that the lowest number it will accept for agcount is 44. I now have a file system with the following structure:
meta-data=/dev/md0 isize=256 agcount=44, agsize=266361205 blks
= sectsz=512
data = bsize=4096 blocks=11719892992, imaxpct=25
= sunit=0 swidth=0 blks, unwritten=1
naming =version 2 bsize=4096 log =internal log bsize=4096 blocks=32768, version=1
= sectsz=512 sunit=0 blks
realtime =none extsz=65536 blocks=0, rtextents=0
I have two questions:
1. Does the agcount have to be a power of 2? Almost every example of agcount I've seen online has been a power of 2 (2, 4, 8, 16, and 32). I originally tried an agcount of 64 which worked but then tried to size it down so it wasn't too large. Will this cause problems later.
2. Is 44 too large? Will I experience a slow down as the disk fills? I've seen people recommend that you not go over agcount=32 and even someone who said not to exceed agcount=8. What are the long term ramifications of this?
Thanks,
Josh
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs
Quoted 4 lines · Josh Greenberg
I've just installed xfs for the first time and I'm trying to put an xfs file system on a large disk. When I just tried with no arguments, it told me that the agsize was too large and the maximum is 268435455 blocks.
Odd, mkfs.xfs w/ no args should always work. Which version of e2fsprogs? How big is the block device (from /proc/partitions?)
Quoted 7 lines
I wasn't familiar with allocation groups at all so I researched this a little bit. I found out what an allocation group is but there aren't many recommendations on agcount other than "don't make it too big" because it slows the disk down as it gets full. However, after playing with the numbers, I found that the lowest number it will accept for agcount is 44. I now have a file system with the following structure:
Quoted 9 lines
meta-data=/dev/md0 isize=256 agcount=44, agsize=266361205 blks
= sectsz=512 data = bsize=4096 blocks=11719892992, imaxpct=25 = sunit=0 swidth=0 blks, unwritten=1 naming =version 2 bsize=4096 log =internal log bsize=4096 blocks=32768, version=1 = sectsz=512 sunit=0 blks realtime =none extsz=65536 blocks=0, rtextents=0
43T, nice :)
Quoted 3 lines
I have two questions:
1. Does the agcount have to be a power of 2? Almost every example of agcount I've seen online has been a power of 2 (2, 4, 8, 16, and 32).
nope
Quoted 3 lines
I
originally tried an agcount of 64 which worked but then tried to size it down so it wasn't too large. Will this cause problems later.
No, this is likely fine. This should be the default; for filesystems > 32T it should max the AG size and give you 1 AG per Terabyte.
Quoted 4 lines
2. Is 44 too large? Will I experience a slow down as the disk fills? I've seen people recommend that you not go over agcount=32 and even someone who said not to exceed agcount=8. What are the long term ramifications of this?
well, smaller agcount -> larger AG. There's also a limit to the AG size (1T IIRC), so there is no hard upper limit on ag count; bigger filesystems will eventually require more AGs.
The upstream default is 4 AGs for smaller filesystems, but for 43T I think the default is to go to 1T AGs.
Subdirectories spread out over AGs (each new subdir's files go to a new AG, in general, all other things being equal) so for smaller filesystems, 8 or 16 AGs was getting a little painful because stuff was being flung all over the disk.
One thing you probably do want to do, however, is match the xfs geometry to your raid geometry, and specify sunit/swidth or su/sw combinations at mkfs time. mkfs.xfs gets this geometry from lvm/md/evms/etc but can't get it from a hardware raid; you'll need to input that yourself.
-Eric
_______________________________________________
xfs mailing list
[email protected]
http://oss.sgi.com/mailman/listinfo/xfs