Skip to contentSkip to conversation

Remove non-CONFIG_NET_MULTI option for PPC4xx EMAC

PATCH New Ben Warren 2 participants 9 messages Apr 28, 2009 – May 26, 2009

Subsystems (2)
lore
Share & tools
lore

Ben Warren

author
#0 lore raw

cover Remove non-CONFIG_NET_MULTI option for PPC4xx EMAC

Hello,

This patch set switches all remaining PPC4xx boards to use CONFIG_NET_MULTI. I haven't been able to test any of the boards, but MAKEALL 4xx ran OK. I remember that some of the 4xx linker scripts specified 'ppc_4xx_eth_initialize', so maybe that's necessary in some cases?

regards,
Ben

author
#1 lore raw

PATCH 1/2 Enable CONFIG_NET_MULTI on all remaining PPC4xx boards

All in-tree PPC4xx boards now use CONFIG_NET_MULTI

---
 include/configs/AR405.h          |    1 +
 include/configs/CPCIISER4.h      |    1 +
 include/configs/CRAYL1.h         |    1 +
 include/configs/DP405.h          |    1 +
 include/configs/ERIC.h           |    1 +
 include/configs/EXBITGEN.h       |    1 +
 include/configs/HUB405.h         |    1 +
 include/configs/JSE.h            |    1 +
 include/configs/MIP405.h         |    1 +
 include/configs/OCRTC.h          |    1 +
 include/configs/ORSG.h           |    1 +
 include/configs/PIP405.h         |    1 +
 include/configs/W7OLMC.h         |    1 +
 include/configs/W7OLMG.h         |    1 +
 include/configs/WUH405.h         |    1 +
 include/configs/csb272.h         |    1 +
 include/configs/csb472.h         |    1 +
 include/configs/netstal-common.h |    2 +-
 include/configs/sbc405.h         |    1 +
 19 files changed, 19 insertions(+), 1 deletions(-)
include/configs/AR405.h +1 -0
index 9f19269..73e34bd 100644
@@ -71,6 +71,7 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/CPCIISER4.h +1 -0
index 3263712..b2679e5 100644
@@ -54,6 +54,7 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/CRAYL1.h +1 -0
index 150bd29..96bf161 100644
@@ -45,6 +45,7 @@
 #define	CONFIG_PHY_ADDR		1	/* PHY address; handling of ENET */
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* early setup for 405gp */
 #define CONFIG_MISC_INIT_R	1	/* so that a misc_init_r() is called */
+#define CONFIG_NET_MULTI
 
 /* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to
  * keep possible initrd ramdisk decompression out.  This is in k (1024 bytes)
include/configs/DP405.h +1 -0
index 187547d..7eb9357 100644
@@ -55,6 +55,7 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/ERIC.h +1 -0
index 201e62a..023f33e 100644
@@ -96,6 +96,7 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/EXBITGEN.h +1 -0
index 4729464..4d08243 100644
@@ -81,6 +81,7 @@
 
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/HUB405.h +1 -0
index 0e7d2c0..ea502d4 100644
@@ -60,6 +60,7 @@
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/JSE.h +1 -0
index 8aca1f9..80c70e4 100644
@@ -135,6 +135,7 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/MIP405.h +1 -0
index a3869c8..8315cfe 100644
@@ -341,6 +341,7 @@
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
 #define CONFIG_PHY_RESET_DELAY	300	/* Intel LXT971A needs this */
 #define CONFIG_PHY_CMD_DELAY	40	/* Intel LXT971A needs this */
+#define CONFIG_NET_MULTI
 /************************************************************
  * RTC
  ***********************************************************/
include/configs/OCRTC.h +1 -0
index 2591f1d..860ec52 100644
@@ -54,6 +54,7 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/ORSG.h +1 -0
index 13d6e04..b2e2d41 100644
@@ -54,6 +54,7 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_NET_MULTI
 
 
 /*
include/configs/PIP405.h +1 -0
index 5c4d69b..e214d70 100644
@@ -281,6 +281,7 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
+#define CONFIG_NET_MULTI
 /************************************************************
  * RTC
  ***********************************************************/
include/configs/W7OLMC.h +1 -0
index ceef76e..553845d 100644
@@ -68,6 +68,7 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1		/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0		/* PHY address			*/
+#define CONFIG_NET_MULTI
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 
include/configs/W7OLMG.h +1 -0
index 11e0630..73d6d24 100644
@@ -68,6 +68,7 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1		/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0		/* PHY address			*/
+#define CONFIG_NET_MULTI
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 #define CONFIG_DTT_LM75     1                /* ON Semi's LM75 */
include/configs/WUH405.h +1 -0
index 99188bc..5c281a1 100644
@@ -58,6 +58,7 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_NET_MULTI
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
include/configs/csb272.h +1 -0
index 204aea0..aed6f50 100644
@@ -184,6 +184,7 @@
 #define CONFIG_PHY_CMD_DELAY	40	/* PHY COMMAND delay		*/
 					/* 32usec min. for LXT971A	*/
 #define CONFIG_PHY_RESET_DELAY	300	/* PHY RESET recovery delay	*/
+#define CONFIG_NET_MULTI
 
 /*
  * RTC configuration
include/configs/csb472.h +1 -0
index 9b3a11c..24b961f 100644
@@ -183,6 +183,7 @@
 #define CONFIG_PHY_CMD_DELAY	40	/* PHY COMMAND delay		*/
 					/* 32usec min. for LXT971A	*/
 #define CONFIG_PHY_RESET_DELAY	300	/* PHY RESET recovery delay	*/
+#define CONFIG_NET_MULTI
 
 /*
  * RTC configuration
include/configs/netstal-common.h +1 -1
index 4d5c1ab..4bed7ae 100644
@@ -61,8 +61,8 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII			/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
-#if defined(CONFIG_440)
 #define CONFIG_NET_MULTI	1
+#if defined(CONFIG_440)
 #define CONFIG_NETCONSOLE		/* include NetConsole support	*/
 #define CONFIG_SYS_RX_ETH_BUFFER	32	/* number of eth rx buffers	*/
 #else
include/configs/sbc405.h +1 -0
index 7197aaf..242f42f 100644
@@ -62,6 +62,7 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_PHY_RESET_DELAY	300	/* Intel LXT971A needs this	*/
+#define CONFIG_NET_MULTI
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"bootargs=emac(0,0)host:/T221ppc/target/config/sbc405/vxWorks.st " \
Signature · 1 line
1.5.6.3
author
#2 lore raw

PATCH 2/2 Remove support for non-CONFIG_NET_MULTI on PPC4xx EMAC

---
 drivers/net/4xx_enet.c |   54 ------------------------------------------------
 net/eth.c              |    4 ---
 2 files changed, 0 insertions(+), 58 deletions(-)
drivers/net/4xx_enet.c +0 -54
index 918373b..adac00f 100644
@@ -259,9 +259,6 @@ static const struct fixed_phy_port fixed_phy_port[] = {
 /*-----------------------------------------------------------------------------+
  * Global variables. TX and RX descriptors and buffers.
  *-----------------------------------------------------------------------------*/
-#if !defined(CONFIG_NET_MULTI)
-struct eth_device *emac0_dev = NULL;
-#endif
 
 /*
  * Get count of EMAC devices (doesn't have to be the max. possible number
@@ -1641,11 +1638,7 @@ int enetInt (struct eth_device *dev)
 	 * Because the mal is generic, we need to get the current
 	 * eth device
 	 */
-#if defined(CONFIG_NET_MULTI)
 	dev = eth_get_dev();
-#else
-	dev = emac0_dev;
-#endif
 
 	hw_p = dev->priv;
 
@@ -2064,60 +2057,13 @@ int ppc_4xx_eth_initialize (bd_t * bis)
 			virgin = 1;
 		}
 
-#if defined(CONFIG_NET_MULTI)
 		eth_register (dev);
-#else
-		emac0_dev = dev;
-#endif
 
-#if defined(CONFIG_NET_MULTI)
 #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
 		miiphy_register (dev->name,
 				 emac4xx_miiphy_read, emac4xx_miiphy_write);
 #endif
-#endif
 	}			/* end for each supported device */
 
 	return 0;
 }
-
-#if !defined(CONFIG_NET_MULTI)
-void eth_halt (void) {
-	if (emac0_dev) {
-		ppc_4xx_eth_halt(emac0_dev);
-		free(emac0_dev);
-		emac0_dev = NULL;
-	}
-}
-
-int eth_init (bd_t *bis)
-{
-	ppc_4xx_eth_initialize(bis);
-	if (emac0_dev) {
-		return ppc_4xx_eth_init(emac0_dev, bis);
-	} else {
-		printf("ERROR: ethaddr not set!\n");
-		return -1;
-	}
-}
-
-int eth_send(volatile void *packet, int length)
-{
-	return (ppc_4xx_eth_send(emac0_dev, packet, length));
-}
-
-int eth_rx(void)
-{
-	return (ppc_4xx_eth_rx(emac0_dev));
-}
-
-int emac4xx_miiphy_initialize (bd_t * bis)
-{
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
-	miiphy_register ("ppc_4xx_eth0",
-			 emac4xx_miiphy_read, emac4xx_miiphy_write);
-#endif
-
-	return 0;
-}
-#endif /* !defined(CONFIG_NET_MULTI) */
net/eth.c +0 -4
index caba80b..913350f 100644
@@ -502,7 +502,6 @@ char *eth_get_name (void)
 #elif defined(CONFIG_CMD_NET) && !defined(CONFIG_NET_MULTI)
 
 extern int at91rm9200_miiphy_initialize(bd_t *bis);
-extern int emac4xx_miiphy_initialize(bd_t *bis);
 extern int mcf52x2_miiphy_initialize(bd_t *bis);
 extern int ns7520_miiphy_initialize(bd_t *bis);
 
@@ -516,9 +515,6 @@ int eth_initialize(bd_t *bis)
 #if defined(CONFIG_AT91RM9200)
 	at91rm9200_miiphy_initialize(bis);
 #endif
-#if defined(CONFIG_PPC4xx_EMAC)
-	emac4xx_miiphy_initialize(bis);
-#endif
 #if defined(CONFIG_MCF52x2)
 	mcf52x2_miiphy_initialize(bis);
 #endif
Signature · 1 line
1.5.6.3
#3 lore raw

PATCH 2/2 Remove support for non-CONFIG_NET_MULTI on PPC4xx EMAC

Quoted 6 lines · Ben Warren
---
 drivers/net/4xx_enet.c |   54
------------------------------------------------ net/eth.c              |  
 4 ---
 2 files changed, 0 insertions(+), 58 deletions(-)

Ben, this doesn't apply against mainline. I suppose you already based this against your "next"? Best would be if you would apply this patch directly and I'll apply the other one [[PATCH 1/2][Net][ppc4xx] Enable CONFIG_NET_MULTI on all remaining PPC4xx boards].

OK? If yes, I'll send a pull request for my "next" to Wolfgang tomorrow.

Thanks.

BTW: Please add my Signed-off-by to this patch [2/2].

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#4 lore raw

PATCH 2/2 Remove support for non-CONFIG_NET_MULTI on PPC4xx EMAC

Quoted 6 lines · Stefan Roese

Ben, this doesn't apply against mainline. I suppose you already based this against your "next"? Best would be if you would apply this patch directly and I'll apply the other one [[PATCH 1/2][Net][ppc4xx] Enable CONFIG_NET_MULTI on all remaining PPC4xx boards].

OK? If yes, I'll send a pull request for my "next" to Wolfgang tomorrow.

Ben?

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

author
#5 lore raw

PATCH 2/2 Remove support for non-CONFIG_NET_MULTI on PPC4xx EMAC

Hi Stefan,

Quoted 7 lines · Stefan Roese
Quoted 5 lines · Stefan Roese

Ben, this doesn't apply against mainline. I suppose you already based this against your "next"? Best would be if you would apply this patch directly and I'll apply the other one [[PATCH 1/2][Net][ppc4xx] Enable CONFIG_NET_MULTI on all remaining PPC4xx boards].

Quoted 6 lines
Quoted 2 lines

OK? If yes, I'll send a pull request for my "next" to Wolfgang tomorrow.

Ben?

Sorry for the delay. Yeah, please go ahead and apply 1/2 to your tree and ask Wolfgang to pull. The second part can be applied at any time - I'll take care of it. Thanks for your help.

Quoted 3 lines

Best regards,
Stefan

regards,
Ben

author
#6 lore raw

PATCH 2/2 Remove support for non-CONFIG_NET_MULTI on PPC4xx EMAC

Hi Stefan,

Quoted 16 lines · Ben Warren

Hi Stefan,

Quoted 13 lines · Stefan Roese
Quoted 10 lines · Stefan Roese

Ben, this doesn't apply against mainline. I suppose you already based this
against your "next"? Best would be if you would apply this patch directly
and I'll apply the other one [[PATCH 1/2][Net][ppc4xx] Enable CONFIG_NET_MULTI on all remaining PPC4xx boards].

OK? If yes, I'll send a pull request for my "next" to Wolfgang tomorrow.

Quoted 6 lines
Quoted 3 lines

Ben?

Sorry for the delay. Yeah, please go ahead and apply 1/2 to your tree and ask Wolfgang to pull. The second part can be applied at any time
- I'll take care of it. Thanks for your help.

I've gone ahead and applied the second part to the net tree. Hope that's OK.

regards,
Ben

#7 lore raw

PATCH 2/2 Remove support for non-CONFIG_NET_MULTI on PPC4xx EMAC

Quoted 6 lines · On Tuesday 26 May 2009 10:05:12 Ben Warren wrote:
Quoted 3 lines

Sorry for the delay. Yeah, please go ahead and apply 1/2 to your tree and ask Wolfgang to pull. The second part can be applied at any time
- I'll take care of it. Thanks for your help.

I've gone ahead and applied the second part to the net tree. Hope that's OK.

Yes, thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

Applied
#8 lore raw

PATCH 1/2 Enable CONFIG_NET_MULTI on all remaining PPC4xx boards

In reply to Ben Warren
Quoted 3 lines · Ben Warren

All in-tree PPC4xx boards now use CONFIG_NET_MULTI

Applied to ppc4xx/next. Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================