Is there any full story about how to take advantage FDT function ?
And how to configure the kernel to minimize the code modification ?
I am porting U-Boot and Linux to a new board with a MPC875 processor and two serial chips, and U-Boot runs well now. I hear that the FDT function can tell the kernel devices information more flexibly and reduce the code modification indirectly.
But I didn't find enough materials to make my head clear, so any tip is greatly appreciated.
Thanks.
Quoted 11 lines · Gao Ya'nan
And how to configure the kernel to minimize the code modification ?
I am porting U-Boot and Linux to a new board with a MPC875 processor and two serial chips, and U-Boot runs well now. I hear that the FDT function can tell the kernel devices information more flexibly and reduce the code modification indirectly.
But I didn't find enough materials to make my head clear, so any tip is greatly appreciated.
Thanks.
Hi Gao,
I'm not up on 8xx, but it may not have been pulled forward into the "powerpc" architecture (still "ppc"). The "powerpc" architecture switch is where linux/u-boot started using the FDT.
Best regards,
gvb
Hi, Jerry.
2009/9/6 Jerry Van Baren <[email protected]>:
Quoted 12 lines
Quoted 11 lines · Gao Ya'nan
And how to configure the kernel to minimize the code modification ?
I am porting U-Boot and Linux to a new board with a MPC875 processor and two serial chips, ?and U-Boot runs well now. I hear that the FDT function can tell the kernel devices information more flexibly and reduce the code modification indirectly.
But I didn't find enough materials to make my head clear, so any tip is greatly appreciated.
Quoted 8 lines
Quoted 1 line
Thanks.
Hi Gao,
I'm not up on 8xx, but it may not have been pulled forward into the "powerpc" architecture (still "ppc"). ?The "powerpc" architecture switch is where linux/u-boot started using the FDT.
I use U-Boot-V2009.8 and Linux-DENX-v2.6.30.3, and I can't find arch/ppc any more. So, I think FDT will work well in MPC8xx platform.
But I don't know how to use it, perhaps I shoud try the standard MPC885 configuration and dtb file.
Quoted 3 lines
Best regards,
gvb
Thanks.
Best regards
Gao Ya'nan
Quoted 3 lines · Jerry Van Baren
I'm not up on 8xx, but it may not have been pulled forward into the "powerpc" architecture (still "ppc"). The "powerpc" architecture switch is where linux/u-boot started using the FDT.
8xx is supported in arch/powerpc.
-Scott
2009/9/10 Scott Wood <[email protected]>:
Quoted 6 lines · Jerry Van Baren
Quoted 3 lines
I'm not up on 8xx, but it may not have been pulled forward into the "powerpc" architecture (still "ppc"). ?The "powerpc" architecture switch is where linux/u-boot started using the FDT.
8xx is supported in
arch/powerpc.
Yes, I have add CONFIG_OF_LIBFDT and CONFIG_OF_BOARD_SETUP for the FDT support which is missing in U-Boot-v2009.08, and it works well, but I found none complete document on how to write a dts file and add special device in it.
Any tips? Thanks
Gao Ya'nan
Quoted 3 lines
-Scott
Quoted 5 lines · Gao Ya'nan
2009/9/10 Scott Wood <[email protected]>:
Quoted 4 lines · Jerry Van Baren
Quoted 3 lines
I'm not up on 8xx, but it may not have been pulled forward into the "powerpc" architecture (still "ppc"). The "powerpc" architecture switch is where linux/u-boot started using the FDT.
Quoted 8 lines
Quoted 1 line
8xx is supported in
arch/powerpc.Yes, I have add
CONFIG_OF_LIBFDTandCONFIG_OF_BOARD_SETUPfor the FDT support which is missing in U-Boot-v2009.08, and it works well, but I found none complete document on how to write a dts file and add special device in it.Any tips? Thanks
See Documentation/powerpc/booting-without-of.txt, Documentation/powerpc/dts-bindings, and the ePAPR specification for information on the content of device trees.
-Scott
2009/9/10 Scott Wood <[email protected]>:
Quoted 17 lines
Quoted 16 lines · Gao Ya'nan
2009/9/10 Scott Wood <[email protected]>:
Quoted 8 lines · Jerry Van Baren
Quoted 4 lines
I'm not up on 8xx, but it may not have been pulled forward into the "powerpc" architecture (still "ppc"). ?The "powerpc" architecture switch is where linux/u-boot started using the FDT.
8xx is supported in
arch/powerpc.Yes, I have add
CONFIG_OF_LIBFDTandCONFIG_OF_BOARD_SETUPfor the FDT support which is missing in U-Boot-v2009.08, and it works well, but I found none complete document on how to write a dts file and add special device in it.
Quoted 5 lines
Quoted 1 line
Any tips? Thanks
See
Documentation/powerpc/booting-without-of.txt,Documentation/powerpc/dts-bindings, and the ePAPR specification for information on the content of device trees.
I miss the later two, thanks for your tips.
Gao.
Quoted 3 lines
-Scott