Skip to contentSkip to conversation

mpc8260: remove Ethernet node fixup to use generic FDT code.

PATCH New Marcel Ziswiler 3 participants 8 messages Sep 8, 2009 – Sep 10, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

Remove Ethernet node fixup from mgcoge and muas3001 boards and modify its configs for the common mpc8260 code to use generic Ethernet fixup.

---
 board/keymile/mgcoge/mgcoge.c |    5 -----
 board/muas3001/muas3001.c     |   15 ---------------
 include/configs/mgcoge.h      |    1 +
 include/configs/muas3001.h    |    1 +
 4 files changed, 2 insertions(+), 20 deletions(-)
board/keymile/mgcoge/mgcoge.c +0 -5
index d24a4b5..b16a01c 100644
@@ -25,7 +25,6 @@
 #include <mpc8260.h>
 #include <ioports.h>
 #include <malloc.h>
-#include <net.h>
 #include <asm/io.h>
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
@@ -373,10 +372,6 @@ void ft_blob_update (void *blob, bd_t *bd)
 	flash_reg[5] = cpu_to_be32 (info->size);
 	fdt_set_node_and_value (blob, "/localbus/flash at 5,0", "reg", flash_reg,
 				sizeof (flash_reg));
-
-	/* MAC addr */
-	fdt_set_node_and_value (blob, "/soc/cpm/ethernet", "mac-address",
-				bd->bi_enetaddr, sizeof (u8) * 6);
 }
 
 void ft_board_setup (void *blob, bd_t *bd)
board/muas3001/muas3001.c +0 -15
index bf4ccb6..36caed8 100644
@@ -342,21 +342,6 @@ void ft_blob_update (void *blob, bd_t *bd)
 		printf ("ft_blob_update(): cannot find /localbus node "
 			"err:%s\n", fdt_strerror (nodeoffset));
 	}
-	/* MAC Adresse */
-	nodeoffset = fdt_path_offset (blob, "/soc/cpm/ethernet");
-	if (nodeoffset >= 0) {
-		uchar ethaddr[6];
-		eth_getenv_enetaddr("ethaddr", ethaddr);
-		ret = fdt_setprop (blob, nodeoffset, "mac-address", ethaddr,
-					sizeof (uchar) * 6);
-	if (ret < 0)
-		printf ("ft_blob_update): cannot set /soc/cpm/ethernet/mac-address "
-			"property err:%s\n", fdt_strerror (ret));
-	} else {
-		/* memory node is required in dts */
-		printf ("ft_blob_update(): cannot find /soc/cpm/ethernet node "
-			"err:%s\n", fdt_strerror (nodeoffset));
-	}
 
 	/* baudrate */
 	nodeoffset = fdt_path_offset (blob, "/soc/cpm/serial");
include/configs/mgcoge.h +1 -0
index 99ac8c1..55d1fc9 100644
@@ -70,6 +70,7 @@
 #define CONFIG_NET_MULTI	1
 
 #define CONFIG_ETHER_INDEX	4
+#define CONFIG_HAS_ETH0
 #define CONFIG_SYS_SCC_TOUT_LOOP	10000000
 
 # define CONFIG_SYS_CMXSCR_VALUE	(CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
include/configs/muas3001.h +1 -0
index f2d117c..c94daa3 100644
@@ -74,6 +74,7 @@
 
 #define CONFIG_ETHER_INDEX	1
 #define CONFIG_ETHER_ON_FCC1
+#define CONFIG_HAS_ETH0
 #define FCC_ENET
 
 /*
Signature · 1 line
1.6.0.4
#1 lore raw

PATCH 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

Dear Marcel Ziswiler,

Quoted 10 lines · In message <1252423835.5386.15.camel@com-21> you wrote:

Remove Ethernet node fixup from mgcoge and muas3001 boards and modify its configs for the common mpc8260 code to use generic Ethernet fixup.

---
 board/keymile/mgcoge/mgcoge.c |    5 -----
 board/muas3001/muas3001.c     |   15 ---------------
 include/configs/mgcoge.h      |    1 +
 include/configs/muas3001.h    |    1 +
 4 files changed, 2 insertions(+), 20 deletions(-)

Should / could a similar change be added to
"board/keymile/km8xx/km8xx.c", too?

Best regards,

Wolfgang Denk

Signature · 8 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
A secure program has to be robust: it  must  be  able  to  deal  with
conditions  that "can't happen", whether user input, program error or
library/etc. This is basic damage  control.  Buffer  overflow  errors
have nothing to do with security, but everything with stupidity.
                 -- Wietse Venema in <[email protected]>
#2 lore raw

PATCH 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

Hi Wolfgang Denk

Quoted 2 lines · Wolfgang Denk

Should / could a similar change be added to
"board/keymile/km8xx/km8xx.c", too?

You mean the kmsupx4 and mgsuvd boards. I guess as Ethernet node fixup is already done in generic mpc8xx CPU code. I am afraid there might be lots more boards with similar obsolete fixups in board specific code.

Heiko?

Cheers

Marcel Ziswiler

#3 lore raw

PATCH 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

Hello Marcel,

Quoted 7 lines · Marcel Ziswiler

Hi Wolfgang Denk

Quoted 2 lines · Wolfgang Denk

Should / could a similar change be added to
"board/keymile/km8xx/km8xx.c", too?

You mean the kmsupx4 and mgsuvd boards. I guess as Ethernet node fixup is already done in generic mpc8xx CPU code. I am afraid there might be lots more boards with similar obsolete fixups in board specific code.

Yes, thats the kmsupx4 and mgsuvd boards. The generic memory fixup can be used (I tried this), but with the generic Ethernet fixup something goes wrong. If I find time, I take a look at it.

bye
Heiko

Signature · 2 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
#4 lore raw

PATCH 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

Hi Heiko

Quoted 3 lines · Heiko Schocher <hs <at> denx.de> writes:

Yes, thats the kmsupx4 and mgsuvd boards. The generic memory fixup can be used (I tried this), but with the generic Ethernet fixup something goes wrong. If I find time, I take a look at it.

At the beginning I had issues as my device tree was missing an Ethernet alias as that's what the generic Ethernet fixup requires to find the node. On some CPU architectures (e.g. MPC8260) the fixup is gated by some defines (e.g. CONFIG_HAS_ETHx) but on MPC8xx that should not be the case.

Cheers

Marcel

#5 lore raw

PATCH 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

In reply to Marcel Ziswiler

Hello Marcel,

Quoted 10 lines · Marcel Ziswiler

Remove Ethernet node fixup from mgcoge and muas3001 boards and modify its configs for the common mpc8260 code to use generic Ethernet fixup.

---
 board/keymile/mgcoge/mgcoge.c |    5 -----
 board/muas3001/muas3001.c     |   15 ---------------
 include/configs/mgcoge.h      |    1 +
 include/configs/muas3001.h    |    1 +
 4 files changed, 2 insertions(+), 20 deletions(-)

Tested on the mgcoge, and looks OK for the muas3001 board:

Thanks!

bye
Heiko

Signature · 2 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
#6 lore raw

PATCH v2 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

In reply to Marcel Ziswiler

---
Changes since v1:
- Added Heiko's tested-by

 board/keymile/mgcoge/mgcoge.c |    5 -----
 board/muas3001/muas3001.c     |   15 ---------------
 include/configs/mgcoge.h      |    1 +
 include/configs/muas3001.h    |    1 +
 4 files changed, 2 insertions(+), 20 deletions(-)
board/keymile/mgcoge/mgcoge.c +0 -5
index d24a4b5..b16a01c 100644
@@ -25,7 +25,6 @@
 #include <mpc8260.h>
 #include <ioports.h>
 #include <malloc.h>
-#include <net.h>
 #include <asm/io.h>
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
@@ -373,10 +372,6 @@ void ft_blob_update (void *blob, bd_t *bd)
 	flash_reg[5] = cpu_to_be32 (info->size);
 	fdt_set_node_and_value (blob, "/localbus/flash at 5,0", "reg", flash_reg,
 				sizeof (flash_reg));
-
-	/* MAC addr */
-	fdt_set_node_and_value (blob, "/soc/cpm/ethernet", "mac-address",
-				bd->bi_enetaddr, sizeof (u8) * 6);
 }
 
 void ft_board_setup (void *blob, bd_t *bd)
board/muas3001/muas3001.c +0 -15
index bf4ccb6..36caed8 100644
@@ -342,21 +342,6 @@ void ft_blob_update (void *blob, bd_t *bd)
 		printf ("ft_blob_update(): cannot find /localbus node "
 			"err:%s\n", fdt_strerror (nodeoffset));
 	}
-	/* MAC Adresse */
-	nodeoffset = fdt_path_offset (blob, "/soc/cpm/ethernet");
-	if (nodeoffset >= 0) {
-		uchar ethaddr[6];
-		eth_getenv_enetaddr("ethaddr", ethaddr);
-		ret = fdt_setprop (blob, nodeoffset, "mac-address", ethaddr,
-					sizeof (uchar) * 6);
-	if (ret < 0)
-		printf ("ft_blob_update): cannot set /soc/cpm/ethernet/mac-address "
-			"property err:%s\n", fdt_strerror (ret));
-	} else {
-		/* memory node is required in dts */
-		printf ("ft_blob_update(): cannot find /soc/cpm/ethernet node "
-			"err:%s\n", fdt_strerror (nodeoffset));
-	}
 
 	/* baudrate */
 	nodeoffset = fdt_path_offset (blob, "/soc/cpm/serial");
include/configs/mgcoge.h +1 -0
index ea14948..b955749 100644
@@ -70,6 +70,7 @@
 #define CONFIG_NET_MULTI	1
 
 #define CONFIG_ETHER_INDEX	4
+#define CONFIG_HAS_ETH0
 #define CONFIG_SYS_SCC_TOUT_LOOP	10000000
 
 # define CONFIG_SYS_CMXSCR_VALUE	(CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
include/configs/muas3001.h +1 -0
index f031a17..ae033b2 100644
@@ -74,6 +74,7 @@
 
 #define CONFIG_ETHER_INDEX	1
 #define CONFIG_ETHER_ON_FCC1
+#define CONFIG_HAS_ETH0
 #define FCC_ENET
 
 /*
Signature · 1 line
1.6.4.2
#7 lore raw

PATCH v2 1/1 mpc8260: remove Ethernet node fixup to use generic FDT code.

Dear Marcel Ziswiler,

Quoted 11 lines · In message <1252523600.3643.6.camel@com-21> you wrote:

---
Changes since v1:
- Added Heiko's tested-by

 board/keymile/mgcoge/mgcoge.c |    5 -----
 board/muas3001/muas3001.c     |   15 ---------------
 include/configs/mgcoge.h      |    1 +
 include/configs/muas3001.h    |    1 +
 4 files changed, 2 insertions(+), 20 deletions(-)

Patch does not apply:

Applying: mpc8260: remove Ethernet node fixup to use generic FDT code.
error: patch failed: board/muas3001/muas3001.c:342
error: board/muas3001/muas3001.c: patch does not apply
fatal: sha1 information is lacking or useless (board/muas3001/muas3001.c). Repository lacks necessary blobs to fall back on 3-way merge. Cannot fall back to three-way merge.
Patch failed at 0001.
Please fix and repost.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Perl itself is  usually  pretty  good  about  telling  you  what  you
shouldn't do. :-)     - Larry Wall in <[email protected]>