error in fw_printenv
Hi All,
When i executed fw_printenv on an embedded board , it threw an error
IOCTL error : Cannot get MTD information!! Any idea why this error occurred?
The contents of config file which i used shown below
# MTD device name Device offset Env. size Flash sector size
Number of sectors
/dev/mtd0 0x0000 0x1000 0x10000
Please help
Thanks
Rahanesh
Dear Rahanesh,
Quoted 6 lines · In message <[email protected]> you wrote:
When i executed
fw_printenvon an embedded board , it threw an errorIOCTL error : Cannot get MTD information!! Any idea why this error occurred?
Well, looking in the source code, I see a single place with a similar error message:
786 rc = ioctl (fd, MEMGETINFO, &mtdinfo);
787 if (rc < 0) {
788 perror ("Cannot get MTD information");
789 return -1;
790 }
But then, the error message would be:
Cannot get MTD information: XXX XXX XXX
with "XXX XXX XXX" giving an explanation of what goes wrong.
What was the "XXX XXX XXX" that got printed in your case?
Quoted 7 lines
The contents of config file which i used shown below
# MTD device name Device offset Env. size Flash sector size
Number of sectors
/dev/mtd00x00000x10000x10000
Are you sure this is correct? Your environment size is only 4 KiB? And your flash secor size is 64 KiB?
Best regards,
Wolfgang Denk
Signature · 8 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The so-called "desktop metaphor" of today's workstations is instead
an "airplane-seat" metaphor. Anyone who has shuffled a lap full of
papers while seated between two portly passengers will recognize the
difference -- one can see only a very few things at once.
- Fred Brooks, Jr.Hi Wolfgang
Cannot get MTD information: Inappropriate ioctl for device got printed
Thanks
Rahanesh
Quoted 47 lines · Wolfgang Denk
Dear Rahanesh,
Quoted 6 lines · In message <[email protected]> you wrote:
When i executed
fw_printenvon an embedded board , it threw an errorIOCTL error : Cannot get MTD information!! Any idea why this error occurred?
Well, looking in the source code, I see a single place with a similar error message:
786 rc = ioctl (fd, MEMGETINFO, &mtdinfo);
787 if (rc < 0) {
788 perror ("Cannot get MTD information");
789 return -1;
790 }But then, the error message would be:
Cannot get MTD information: XXX XXX XXX
with "XXX XXX XXX" giving an explanation of what goes wrong.
What was the "XXX XXX XXX" that got printed in your case?
Quoted 8 lines
The contents of config file which i used shown below
# MTD device name Device offset Env. size Flash sector size
Number of sectors
/dev/mtd00x00000x10000x10000Are you sure this is correct? Your environment size is only 4 KiB? And your flash secor size is 64 KiB?
Best regards,
Wolfgang Denk
Dear Rahanesh,
please do not top post / full quote. Please make sure to read
http://www.netmeister.org/news/learn2quote.html
Quoted 2 lines · In message <[email protected]> you wrote:
Cannot get MTD information: Inappropriate ioctl for device got printed
Well, that most certainly means that your /dev/mtd0 is not a NOR or NAND flash device.
Best regards,
Wolfgang Denk
Signature · 7 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de There is an old custom among my people. When a woman saves a man's life, he is grateful. -- Nona, the Kanuto which woman, "A Private Little War", stardate 4211.8.
Dear Wolfgang,
Quoted 3 lines
Well, that most certainly means that your
/dev/mtd0is not a NOR or NAND flash device.
I use mtd_debug utility to identify the /dev/mtd0 device. It said
it is Nor flash.
Thanks
Rahanesh
Hi Wolfgang,
Quoted 4 lines
Well, that most certainly means that your
/dev/mtd0is not a NOR or NAND flash device.
Now used the fw_printenv under tools/env directory of uboot. It
does not have IOCTL error.
On issuing a fw_printenv it showd following messages
Bad data CRC, Using default environment and printed only few
environment variables.
Then i did a fw_setenv bootdelay 6. It showed some messgaes of
erasing flash. But it actually erased my uboot itself.
What might be the issue? config file?
MTD device name Device offset Env. size Flash
sector size Number of sectors
/dev/mtd0 0x0000
0x1000 0x10000
What does Device Offset mean?
/dev/mtd0 has both uboot as well as environment variables. Environment variables lie at bottom of /dev/mtd0. Is that the meaning of device offset?
#define CFG_ENV_ADDR 0xAD03F000 (Flash starts at 0xAD000000) #define CFG_ENV_SIZE 0x1000 #define CFG_ENV_SECT_SIZE 0x10000
These are the macro that i found in include/configs/board.h
Please help
Thanks
Rahanesh
Hi Rahanesh,
Quoted 11 lines
Quoted 4 lines
Well, that most certainly means that your
/dev/mtd0is not a NOR or NAND flash device.Now used the
fw_printenvundertools/envdirectory of uboot. It
does not have IOCTL error.On issuing a
fw_printenvit showd following messagesBad data CRC, Using default environment and printed only few
environment variables.
This should have made big warning signs flash up - if data crc was not correct, it was 99% sure that your configuration wasn't ok.
Quoted 2 lines
Then i did a
fw_setenvbootdelay 6. It showed some messgaes of
erasing flash. But it actually erased my uboot itself.
No big wonder here.
Quoted 1 line
What might be the issue? config file?
Of course.
Quoted 7 lines
MTD device name Device offset Env. size Flash
sector size Number of sectors/dev/mtd0 0x0000
0x10000x10000What does Device Offset mean?
Offset is the offset into the area mapped by the device file.
Quoted 2 lines
/dev/mtd0has both uboot as well as environment variables. Environment variables lie at bottom of/dev/mtd0. Is that the meaning of device offset?
That would be the meaning. You can always test by reading /dev/mtd0 directly from linux and inspect its contents, i.e. try
dd if=/dev/mtd0 bs=64k count=1 | hexdump -C | less
(or something comparable) and look for your environment.
Quoted 6 lines
#define CFG_ENV_ADDR 0xAD03F000 (Flash starts at 0xAD000000) #define CFG_ENV_SIZE 0x1000 #define CFG_ENV_SECT_SIZE 0x10000These are the macro that i found in
include/configs/board.h
This looks completly weird to me. Can you tell me exactly what board you are working with? It looks like this cannot be a NOR flash..
Cheers
Detlev
Signature · 6 lines
In God we trust. All others we monitor
-- NSA motto
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-40 Fax: (+49)-8142-66989-80 Email: dzu at denx.de