touch screen not detected by Angstrom Linux
Subsystems (2)
Hello Nicolas,
I could successfully apply your touch screen drivers to 2.6.32-rc2:
2.6.30-at91-exp-0045-input-atmel_tsadcc-touchscreen-use-platform-paramet.patch 2.6.30-at91-exp-0046-at91-input-platform-parameters-for-atmel_tsadcc-in.patch 2.6.30-at91-exp-0047-at91-input-touchscreen-support-for-at91sam9g45ekes.patch
Here dmesg output for 2.6.32-rc2:
atmel_tsadcc atmel_tsadcc: Master clock is set at: 133333333 Hz atmel_tsadcc atmel_tsadcc: Prescaler is set at: 221
input: atmel touch screen controller as /devices/platform/atmel_tsadcc/input/input1
Here dmesg output for 2.6.27 where touch screen is working under Angstrom Linux:
atmel_tsadcc atmel_tsadcc: Master clock is set at: 133333333 Hz atmel_tsadcc atmel_tsadcc: Prescaler is set at: 221
input: atmel touch screen controller as /class/input/input1
The device is working if I read /dev/input/event1, but I'm not able to get it working under Angstrom Linux. Any ideas?
Regards,
Yegor
Yegor Yefremov :
Quoted 14 lines
Hello Nicolas,
I could successfully apply your touch screen drivers to 2.6.32-rc2:
2.6.30-at91-exp-0045-input-atmel_tsadcc-touchscreen-use-platform-paramet.patch 2.6.30-at91-exp-0046-at91-input-platform-parameters-for-atmel_tsadcc-in.patch 2.6.30-at91-exp-0047-at91-input-touchscreen-support-for-at91sam9g45ekes.patch
Here dmesg output for 2.6.32-rc2:
atmel_tsadccatmel_tsadcc: Master clock is set at: 133333333 Hzatmel_tsadccatmel_tsadcc: Prescaler is set at: 221
input: atmel touch screen controller as /devices/platform/atmel_tsadcc/input/input1
Quoted 7 lines
Here dmesg output for 2.6.27 where touch screen is working under Angstrom Linux:
atmel_tsadccatmel_tsadcc: Master clock is set at: 133333333 Hzatmel_tsadccatmel_tsadcc: Prescaler is set at: 221
input: atmel touch screen controller as /class/input/input1The device is working if I read
/dev/input/event1, but I'm not able to get it working under Angstrom Linux. Any ideas?
Yes: in the driver we do not report the pressure measurement (not available on at91sam9rl). There is a bug in tslib that prevents a pressure-less touchscreen to work correctly.
1/ solution one: apply the patch I posted on tslib ml:
https://lists.berlios.de/pipermail/tslib-general/2009-September/000225.html
2/ re-introduce the fake pressure report in your source (atmel_tsadcc driver)
8<-------------------------------------------
drivers/input/touchscreen/atmel_tsadcc.c +3 -0
@@ -134,6 +134,7 @@ static irqreturn_t atmel_tsadcc_interrupt(int irq, void *dev)input_report_key (input_dev,BTN_TOUCH ,0 ); ts_dev->bufferedmeasure =0 ; +input_report_abs (input_dev,ABS_PRESSURE ,0 );input_sync (input_dev); }else if (status &ATMEL_TSADCC_PENCNT ) {
@@ -158,6 +159,7 @@ static irqreturn_t atmel_tsadcc_interrupt(int irq, void *dev)input_report_abs (input_dev,ABS_X , ts_dev->prev_absx);input_report_abs (input_dev,ABS_Y , ts_dev->prev_absy);input_report_key (input_dev,BTN_TOUCH ,1 ); +input_report_abs (input_dev,ABS_PRESSURE ,7500 );input_sync (input_dev); }else ts_dev->bufferedmeasure =1 ;
@@ -256,6 +258,7 @@ static int __devinit atmel_tsadcc_probe(struct platform_device *pdev)__set_bit (EV_ABS , input_dev->evbit);input_set_abs_params (input_dev,ABS_X ,0 ,0x3FF ,0 ,0 );input_set_abs_params (input_dev,ABS_Y ,0 ,0x3FF ,0 ,0 ); +input_set_abs_params (input_dev,ABS_PRESSURE ,0 ,15000 ,0 ,0 );input_set_capability (input_dev,EV_KEY ,BTN_TOUCH );
8<-------------------------------------------
Best regards,
Signature · 1 line
Nicolas Ferre
Quoted 18 lines
Quoted 18 lines
I could successfully apply your touch screen drivers to 2.6.32-rc2:
2.6.30-at91-exp-0045-input-atmel_tsadcc-touchscreen-use-platform-paramet.patch 2.6.30-at91-exp-0046-at91-input-platform-parameters-for-atmel_tsadcc-in.patch 2.6.30-at91-exp-0047-at91-input-touchscreen-support-for-at91sam9g45ekes.patch
Here dmesg output for 2.6.32-rc2:
atmel_tsadccatmel_tsadcc: Master clock is set at: 133333333 Hzatmel_tsadccatmel_tsadcc: Prescaler is set at: 221
input: atmel touch screen controller as /devices/platform/atmel_tsadcc/input/input1Here dmesg output for 2.6.27 where touch screen is working under Angstrom Linux:
atmel_tsadccatmel_tsadcc: Master clock is set at: 133333333 Hzatmel_tsadccatmel_tsadcc: Prescaler is set at: 221
input: atmel touch screen controller as /class/input/input1
Quoted 8 lines
Quoted 1 line
The device is working if I read
/dev/input/event1, but I'm not able to get it working under Angstrom Linux. Any ideas?Yes: in the driver we do not report the pressure measurement (not available on at91sam9rl). There is a bug in tslib that prevents a pressure-less touchscreen to work correctly.
1/ solution one: apply the patch I posted on tslib ml:
https://lists.berlios.de/pipermail/tslib-general/2009-September/000225.html
Your patch was committed about 10 hours ago http://svn.berlios.de/viewcvs/tslib?view=rev&revision=78
Quoted 32 lines
2/ re-introduce the fake pressure report in your source (
atmel_tsadccdriver)8<-------------------------------------------
drivers/input/touchscreen/atmel_tsadcc.c +3
-0@@ -134,6 +134,7 @@ static irqreturn_t atmel_tsadcc_interrupt(int irq, void *dev)input_report_key (input_dev,BTN_TOUCH ,0 ); ts_dev->bufferedmeasure =0 ; +input_report_abs (input_dev,ABS_PRESSURE ,0 );input_sync (input_dev); }else if (status &ATMEL_TSADCC_PENCNT ) {@@ -158,6 +159,7 @@ static irqreturn_t atmel_tsadcc_interrupt(int irq, void *dev)input_report_abs (input_dev,ABS_X , ts_dev->prev_absx);input_report_abs (input_dev,ABS_Y , ts_dev->prev_absy);input_report_key (input_dev,BTN_TOUCH ,1 ); +input_report_abs (input_dev,ABS_PRESSURE ,7500 );input_sync (input_dev); }else ts_dev->bufferedmeasure =1 ;@@ -256,6 +258,7 @@ static int __devinit atmel_tsadcc_probe(struct platform_device *pdev)__set_bit (EV_ABS , input_dev->evbit);input_set_abs_params (input_dev,ABS_X ,0 ,0x3FF ,0 ,0 );input_set_abs_params (input_dev,ABS_Y ,0 ,0x3FF ,0 ,0 ); +input_set_abs_params (input_dev,ABS_PRESSURE ,0 ,15000 ,0 ,0 );input_set_capability (input_dev,EV_KEY ,BTN_TOUCH );
Quoted 1 line
8<-------------------------------------------
I have used the second solution and it is working like a charm. Thank you for support.
Regards,
Yegor