Skip to contentSkip to conversation

New MIIPHYBB implementation with multi-bus support

PATCH Superseded Luigi 'Comio' Mantellini 2 participants 6 messages Oct 6, 2009 – Oct 10, 2009

Subsystems (2)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v4 cover New MIIPHYBB implementation with multi-bus support

This patch rewrites the miiphybb ( Bit-banged MII bus driver ) in order to support an arbitrary number of mii buses. This feature is useful when your board uses different mii buses for different phys and all (or a part) of these buses are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board configuration file:

CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs to define at least the following macros:

MII_INIT      - Generic code to enable the MII bus (optional)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
MDC(v)        - Write v on the MDC pin

The previous macros make the driver compatible with the previous version (that didn't support the multi-bus).

When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill the bb_miiphy_buses[] array with a record for each required bus and declare the bb_miiphy_buses_num variable with the number of mii buses. The record (struct bb_miiphy_bus) has the following fields/callbacks (see miiphy.h for details):

char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin

int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = "miibus#1", .init = b1_init, .mdio_active = b1_mdio_active, ... }, { .name = "miibus#2", .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
};
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /

                          sizeof(bb_miiphy_buses[0]);

Patch Changelog:

v1 -- First (broken) release
v2 -- Fix some typos and disable callbacks pointers relacation (if
CONFIG_RELOC_FIXUP_WORKS is not defined)
v3 -- Do not relocate NULL pointers
v4 -- Code Cleanup.

Luigi 'Comio' Mantellini (3):
New Bit-banged MII driver (MIIPHYBB) implementation with multi-bus
support.
Add bb_miiphy_init call before any ethernet bring-up code. Update all board to support new bbmiiphy driver (with multibus
support)

 drivers/net/phy/miiphybb.c   |  346 +++++++++++++++++++++++++++++-------------
 include/configs/ISPAN.h      |    4 +
 include/configs/MPC8260ADS.h |    3 +
 include/configs/MPC8266ADS.h |    4 +
 include/configs/MPC8560ADS.h |    4 +
 include/configs/Rattler.h    |    4 +
 include/configs/SBC8540.h    |    4 +
 include/configs/TQM8272.h    |    3 +
 include/configs/VoVPN-GW.h   |    4 +
 include/configs/ZPC1900.h    |    4 +
 include/configs/ep8248.h     |    4 +
 include/configs/ep82xxm.h    |    4 +
 include/configs/gw8260.h     |    4 +
 include/configs/hymod.h      |   12 ++
 include/configs/muas3001.h   |    4 +
 include/configs/ppmc8260.h   |    4 +
 include/configs/sacsng.h     |    4 +
 include/configs/sbc8260.h    |    4 +
 include/configs/sbc8560.h    |    4 +
 include/miiphy.h             |   25 +++-
 lib_arm/board.c              |    7 +
 lib_avr32/board.c            |    7 +
 lib_blackfin/board.c         |    7 +
 lib_i386/board.c             |    9 +-
 lib_m68k/board.c             |    7 +
 lib_mips/board.c             |    7 +
 lib_ppc/board.c              |    7 +
 lib_sh/board.c               |    7 +
 lib_sparc/board.c            |    7 +
 29 files changed, 408 insertions(+), 106 deletions(-)
#1 lore raw

PATCH v4 1/3 New Bit-banged MII driver (MIIPHYBB) implementation with multi-bus support.

This patch rewrites the miiphybb ( Bit-banged MII bus driver ) in order to support an arbitrary number of mii buses. This feature is useful when your board uses different mii buses for different phys and all (or a part) of these buses are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board configuration file:

CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs to define at least the following macros:

MII_INIT      - Generic code to enable the MII bus (optional)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
MDC(v)        - Write v on the MDC pin

The previous macros make the driver compatible with the previous version (that didn't support the multi-bus).

When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill the bb_miiphy_buses[] array with a record for each required bus and declare the bb_miiphy_buses_num variable with the number of mii buses. The record (struct bb_miiphy_bus) has the following fields/callbacks (see miiphy.h for details):

char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin

int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = "miibus#1", .init = b1_init, .mdio_active = b1_mdio_active, ... }, { .name = "miibus#2", .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
};
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /

                          sizeof(bb_miiphy_buses[0]);
---
 drivers/net/phy/miiphybb.c |  346 +++++++++++++++++++++++++++++++-------------
 include/miiphy.h           |   25 +++-
 2 files changed, 266 insertions(+), 105 deletions(-)
drivers/net/phy/miiphybb.c +242 -104
index b77c917..259b3ff 100644
@@ -1,4 +1,7 @@
 /*
+ * (C) Copyright 2009 Industrie Dial Face S.p.A.
+ * Luigi 'Comio' Mantellini <[email protected]>
+ *
  * (C) Copyright 2001
  * Gerald Van Baren, Custom IDEAS, vanbaren at cideas.com.
  *
@@ -29,18 +32,144 @@
 #include <common.h>
 #include <ioports.h>
 #include <ppc_asm.tmpl>
+#include <miiphy.h>
+
+#define BB_MII_RELOCATE(v,off) (v += (v?off:0))
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_BITBANGMII_MULTI
+
+/*
+ * If CONFIG_BITBANGMII_MULTI is not defined we use a
+ * compatibility layer with the previous miiphybb implementation
+ * based on macros usage.
+ *
+ */
+static int bb_mii_init_wrap(struct bb_miiphy_bus *bus)
+{
+#ifdef MII_INIT
+	MII_INIT;
+#endif
+	return 0;
+}
+
+static int bb_mdio_active_wrap(struct bb_miiphy_bus *bus)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO_ACTIVE;
+	return 0;
+}
+
+static int bb_mdio_tristate_wrap(struct bb_miiphy_bus *bus)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO_TRISTATE;
+	return 0;
+}
+
+static int bb_set_mdio_wrap(struct bb_miiphy_bus *bus, int v)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO(v);
+	return 0;
+}
+
+static int bb_get_mdio_wrap(struct bb_miiphy_bus *bus, int *v)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	*v = MDIO_READ;
+	return 0;
+}
+
+static int bb_set_mdc_wrap(struct bb_miiphy_bus *bus, int v)
+{
+#ifdef MDC_DECLARE
+	MDC_DECLARE;
+#endif
+	MDC(v);
+	return 0;
+}
+
+static int bb_delay_wrap(struct bb_miiphy_bus *bus)
+{
+	MIIDELAY;
+	return 0;
+}
+
+struct bb_miiphy_bus bb_miiphy_buses[] = {
+	{
+		.name = BB_MII_DEVNAME,
+		.init = bb_mii_init_wrap,
+		.mdio_active = bb_mdio_active_wrap,
+		.mdio_tristate = bb_mdio_tristate_wrap,
+		.set_mdio = bb_set_mdio_wrap,
+		.get_mdio = bb_get_mdio_wrap,
+		.set_mdc = bb_set_mdc_wrap,
+		.delay = bb_delay_wrap,
+	}
+};
+
+extern int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
+                                 sizeof(bb_miiphy_buses[0]);
+#endif
+
+void bb_miiphy_init(void)
+{
+	int i;
+
+	for (i = 0; i < bb_miiphy_buses_num; i++) {
+#if !defined(CONFIG_RELOC_FIXUP_WORKS)
+		/* Relocate the hook pointers*/
+		BB_MII_RELOCATE(bb_miiphy_buses[i].init, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].mdio_active, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].mdio_tristate, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].set_mdio, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].get_mdio, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].set_mdc, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].delay, gd->reloc_off);
+#endif
+		if (bb_miiphy_buses[i].init != NULL) {
+			bb_miiphy_buses[i].init(&bb_miiphy_buses[i]);
+		}
+	}
+}
+
+static inline struct bb_miiphy_bus *bb_miiphy_getbus(char *devname)
+{
+#ifdef CONFIG_BITBANGMII_MULTI
+	int i;
+
+	/* Search the correct bus */
+	for (i = 0; i < bb_miiphy_buses_num; i++) {
+		if (!strcmp(bb_miiphy_buses[i].name, devname)) {
+			return &bb_miiphy_buses[i];
+		}
+	}
+	return NULL;
+#else
+	/* We have just one bitbanging bus */
+	return &bb_miiphy_buses[0];
+#endif
+}
 
 /*****************************************************************************
  *
  * Utility to send the preamble, address, and register (common to read
  * and write).
  */
-static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
+static void miiphy_pre(struct bb_miiphy_bus *bus, char read,
+                       unsigned char addr, unsigned char reg)
 {
-	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
+	int j;
 
 	/*
 	 * Send a 32 bit preamble ('1's) with an extra '1' bit for good measure.
@@ -50,67 +179,66 @@ static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
 	 * but it is safer and will be much more robust.
 	 */
 
-	MDIO_ACTIVE;
-	MDIO (1);
+	bus->mdio_active(bus);
+	bus->set_mdio(bus, 1);
 	for (j = 0; j < 32; j++) {
-		MDC (0);
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->set_mdc(bus, 0);
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 	}
 
 	/* send the start bit (01) and the read opcode (10) or write (10) */
-	MDC (0);
-	MDIO (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (1);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (read);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (!read);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, read);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, !read);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	/* send the PHY address */
 	for (j = 0; j < 5; j++) {
-		MDC (0);
+		bus->set_mdc(bus, 0);
 		if ((addr & 0x10) == 0) {
-			MDIO (0);
+			bus->set_mdio(bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio(bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		addr <<= 1;
 	}
 
 	/* send the register address */
 	for (j = 0; j < 5; j++) {
-		MDC (0);
+		bus->set_mdc(bus, 0);
 		if ((reg & 0x10) == 0) {
-			MDIO (0);
+			bus->set_mdio(bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio(bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		reg <<= 1;
 	}
 }
 
-
 /*****************************************************************************
  *
  * Read a MII PHY register.
@@ -118,63 +246,69 @@ static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
  * Returns:
  *   0 on success
  */
-int bb_miiphy_read (char *devname, unsigned char addr,
-		unsigned char reg, unsigned short *value)
+int bb_miiphy_read(char *devname, unsigned char addr,
+                   unsigned char reg, unsigned short *value)
 {
-	short rdreg;		/* register working value */
-	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
+	short rdreg; /* register working value */
+	int v;
+	int j; /* counter */
+	struct bb_miiphy_bus *bus;
+
+	bus = bb_miiphy_getbus(devname);
+	if (bus == NULL) {
+		return -1;
+	}
 
 	if (value == NULL) {
 		puts("NULL value pointer\n");
-		return (-1);
+		return -1;
 	}
 
-	miiphy_pre (1, addr, reg);
+	miiphy_pre (bus, 1, addr, reg);
 
 	/* tri-state our MDIO I/O pin so we can read */
-	MDC (0);
-	MDIO_TRISTATE;
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->mdio_tristate(bus);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	/* check the turnaround bit: the PHY should be driving it to zero */
-	if (MDIO_READ != 0) {
+	bus->get_mdio(bus, &v);
+	if (v != 0) {
 		/* puts ("PHY didn't drive TA low\n"); */
 		for (j = 0; j < 32; j++) {
-			MDC (0);
-			MIIDELAY;
-			MDC (1);
-			MIIDELAY;
+			bus->set_mdc(bus, 0);
+			bus->delay(bus);
+			bus->set_mdc(bus, 1);
+			bus->delay(bus);
 		}
 		/* There is no PHY, set value to 0xFFFF and return */
 		*value = 0xFFFF;
-		return (-1);
+		return -1;
 	}
 
-	MDC (0);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->delay(bus);
 
 	/* read 16 bits of register data, MSB first */
 	rdreg = 0;
 	for (j = 0; j < 16; j++) {
-		MDC (1);
-		MIIDELAY;
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		rdreg <<= 1;
-		rdreg |= MDIO_READ;
-		MDC (0);
-		MIIDELAY;
+		bus->get_mdio(bus, &v);
+		rdreg |= (v & 0x1);
+		bus->set_mdc(bus, 0);
+		bus->delay(bus);
 	}
 
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	*value = rdreg;
 
@@ -194,49 +328,53 @@ int bb_miiphy_read (char *devname, unsigned char addr,
  *   0 on success
  */
 int bb_miiphy_write (char *devname, unsigned char addr,
-		unsigned char reg, unsigned short value)
+                     unsigned char reg, unsigned short value)
 {
+	struct bb_miiphy_bus *bus;
 	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
 
-	miiphy_pre (0, addr, reg);
+	bus = bb_miiphy_getbus(devname);
+	if (bus == NULL) {
+		/* Bus not found! */
+		return -1;
+	}
+
+	miiphy_pre (bus, 0, addr, reg);
 
 	/* send the turnaround (10) */
-	MDC (0);
-	MDIO (1);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	/* write 16 bits of register data, MSB first */
 	for (j = 0; j < 16; j++) {
-		MDC (0);
+		bus->set_mdc(bus, 0);
 		if ((value & 0x00008000) == 0) {
-			MDIO (0);
+			bus->set_mdio(bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio(bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		value <<= 1;
 	}
 
 	/*
 	 * Tri-state the MDIO line.
 	 */
-	MDIO_TRISTATE;
-	MDC (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->mdio_tristate(bus);
+	bus->set_mdc(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	return 0;
-}
+}
\ No newline at end of file
include/miiphy.h +24 -1
index fa33ec7..5362125 100644
@@ -19,6 +19,8 @@
 |
 |	COPYRIGHT   I B M   CORPORATION 1999
 |	LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
+|
+|   Additions (C) Copyright 2009 Industrie Dial Face S.p.A.
 +----------------------------------------------------------------------------*/
 /*----------------------------------------------------------------------------+
 |
@@ -61,12 +63,33 @@ char *miiphy_get_current_dev (void);
 
 void miiphy_listdev (void);
 
-#define BB_MII_DEVNAME	"bbmii"
+#ifdef CONFIG_BITBANGMII
+
+#define BB_MII_DEVNAME	"bb_miiphy"
+
+struct bb_miiphy_bus {
+	char name[NAMESIZE];
+	int (*init)(struct bb_miiphy_bus *bus);
+	int (*mdio_active)(struct bb_miiphy_bus *bus);
+	int (*mdio_tristate)(struct bb_miiphy_bus *bus);
+	int (*set_mdio)(struct bb_miiphy_bus *bus, int v);
+	int (*get_mdio)(struct bb_miiphy_bus *bus, int *v);
+	int (*set_mdc)(struct bb_miiphy_bus *bus, int v);
+	int (*delay)(struct bb_miiphy_bus *bus);
+#ifdef CONFIG_BITBANGMII_MULTI
+	void *priv;
+#endif
+};
+
+extern struct bb_miiphy_bus bb_miiphy_buses[];
+extern int bb_miiphy_buses_num;
 
+void bb_miiphy_init (void);
 int bb_miiphy_read (char *devname, unsigned char addr,
 		    unsigned char reg, unsigned short *value);
 int bb_miiphy_write (char *devname, unsigned char addr,
 		     unsigned char reg, unsigned short value);
+#endif
 
 /* phy seed setup */
 #define AUTO			99
Signature · 1 line
1.6.3.3
#2 lore raw

PATCH v4 2/3 Add bb_miiphy_init call before any ethernet bring-up code.

---
 lib_arm/board.c      |    7 +++++++
 lib_avr32/board.c    |    7 +++++++
 lib_blackfin/board.c |    7 +++++++
 lib_i386/board.c     |    9 ++++++++-
 lib_m68k/board.c     |    7 +++++++
 lib_mips/board.c     |    7 +++++++
 lib_ppc/board.c      |    7 +++++++
 lib_sh/board.c       |    7 +++++++
 lib_sparc/board.c    |    7 +++++++
 9 files changed, 64 insertions(+), 1 deletions(-)
lib_arm/board.c +7 -0
index a0e56d5..057cc21 100644
@@ -50,6 +50,10 @@
 #include <onenand_uboot.h>
 #include <mmc.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #ifdef CONFIG_DRIVER_SMC91111
 #include "../drivers/net/smc91111.h"
 #endif
@@ -417,6 +421,9 @@ extern void davinci_eth_set_mac_addr (const u_int8_t *addr);
 	mmc_initialize (gd->bd);
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	puts ("Net:   ");
lib_avr32/board.c +7 -0
index 29999d8..1f5e681 100644
@@ -27,6 +27,10 @@
 #include <version.h>
 #include <net.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #include <asm/initcalls.h>
 #include <asm/sections.h>
 
@@ -337,6 +341,9 @@ void board_init_r(gd_t *new_gd, ulong dest_addr)
 	if (s)
 		load_addr = simple_strtoul(s, NULL, 16);
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	s = getenv("bootfile");
 	if (s)
lib_blackfin/board.c +7 -0
index 1053f69..6ce17d4 100644
@@ -26,6 +26,10 @@
 #include <nand.h>	/* cannot even include nand.h if it isnt configured */
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #if defined(CONFIG_POST)
 #include <post.h>
 int post_flag;
@@ -270,6 +274,9 @@ void board_init_f(ulong bootflag)
 
 static void board_net_init_r(bd_t *bd)
 {
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #ifdef CONFIG_CMD_NET
 	uchar enetaddr[6];
 	char *s;
lib_i386/board.c +8 -1
index 0262b5e..452a5fc 100644
@@ -1,6 +1,6 @@
 /*
  * (C) Copyright 2002
- * Daniel Engstr?m, Omicron Ceti AB, daniel at omicron.se
+ * Daniel Engstr???m, Omicron Ceti AB, daniel at omicron.se
  *
  * (C) Copyright 2002
  * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
@@ -39,6 +39,10 @@
 #include <ide.h>
 #include <asm/u-boot-i386.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 extern long _i386boot_start;
@@ -351,6 +355,9 @@ void start_i386boot (void)
 	doc_init();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET();
lib_m68k/board.c +7 -0
index 3d88530..768a55c 100644
@@ -63,6 +63,10 @@
 #include <spi.h>
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #include <nand.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -630,6 +634,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	nand_init();		/* go init the NAND */
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	WATCHDOG_RESET();
 #if defined(FEC_ENET)
lib_mips/board.c +7 -0
index f62a46a..81d6681 100644
@@ -33,6 +33,10 @@
 #include <onenand_uboot.h>
 #include <spi.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 #if ( ((CONFIG_ENV_ADDR+CONFIG_ENV_SIZE) < CONFIG_SYS_MONITOR_BASE) || \
@@ -407,6 +411,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	misc_init_r ();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	puts ("Net:   ");
lib_ppc/board.c +7 -0
index f9dbdb9..b19e6be 100644
@@ -83,6 +83,10 @@
 #include <asm/mp.h>
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #ifdef CONFIG_SYS_UPDATE_FLASH_SIZE
 extern int update_flash_size (int flash_size);
 #endif
@@ -992,6 +996,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	doc_init ();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET ();
lib_sh/board.c +7 -0
index 5d61f0d..b769788 100644
@@ -28,6 +28,10 @@
 #include <net.h>
 #include <environment.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 extern void malloc_bin_reloc (void);
 extern int cpu_init(void);
 extern int board_init(void);
@@ -178,6 +182,9 @@ void sh_generic_init(void)
 #endif /* CONFIG_WATCHDOG*/
 
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	{
 		char *s;
lib_sparc/board.c +7 -0
index 6aadb56..f00f24d 100644
@@ -49,6 +49,10 @@
 #include <ambapp.h>
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 /* Debug options
@@ -405,6 +409,9 @@ void board_init_f(ulong bootflag)
 	doc_init();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET();
Signature · 1 line
1.6.3.3
#3 lore raw

PATCH v4 3/3 Update all board to support new bbmiiphy driver (with multibus support)

---
 include/configs/ISPAN.h      |    4 ++++
 include/configs/MPC8260ADS.h |    3 +++
 include/configs/MPC8266ADS.h |    4 ++++
 include/configs/MPC8560ADS.h |    4 ++++
 include/configs/Rattler.h    |    4 ++++
 include/configs/SBC8540.h    |    4 ++++
 include/configs/TQM8272.h    |    3 +++
 include/configs/VoVPN-GW.h   |    4 ++++
 include/configs/ZPC1900.h    |    4 ++++
 include/configs/ep8248.h     |    4 ++++
 include/configs/ep82xxm.h    |    4 ++++
 include/configs/gw8260.h     |    4 ++++
 include/configs/hymod.h      |   12 ++++++++++++
 include/configs/muas3001.h   |    4 ++++
 include/configs/ppmc8260.h   |    4 ++++
 include/configs/sacsng.h     |    4 ++++
 include/configs/sbc8260.h    |    4 ++++
 include/configs/sbc8560.h    |    4 ++++
 18 files changed, 78 insertions(+), 0 deletions(-)
include/configs/ISPAN.h +4 -0
index 6eb466a..02a188d 100644
@@ -84,6 +84,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		3		/* Port D */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 
 #define CONFIG_SYS_MDIO_PIN		0x00040000	/* PD13 */
 #define CONFIG_SYS_MDC_PIN		0x00080000	/* PD12 */
include/configs/MPC8260ADS.h +3 -0
index 39b8b8f..078cb6a 100644
@@ -150,6 +150,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
 
 #if CONFIG_ADSTYPE == CONFIG_SYS_8272ADS
 #define CONFIG_SYS_MDIO_PIN	0x00002000	/* PC18 */
include/configs/MPC8266ADS.h +4 -0
index b0162c3..fdfefc0 100644
@@ -96,6 +96,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
include/configs/MPC8560ADS.h +4 -0
index 8ddce5c..54320e5 100644
@@ -363,6 +363,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
include/configs/Rattler.h +4 -0
index 5b6f271..b2427b2 100644
@@ -103,6 +103,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
 #define MDIO_READ		((iop->pdat &  0x00400000) != 0)
include/configs/SBC8540.h +4 -0
index 7cde39b..58b0a68 100644
@@ -290,6 +290,10 @@
    * GPIO pins used for bit-banged MII communications
    */
   #define MDIO_PORT	2		/* Port C */
+  #define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+  #define MDC_DECLARE	MDIO_DECLARE
+
   #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
   #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
   #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
include/configs/TQM8272.h +3 -0
index 6c462af..22df917 100644
@@ -219,6 +219,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
 
 #if STK82xx_150
 #define CONFIG_SYS_MDIO_PIN	0x00008000	/* PC16 */
include/configs/VoVPN-GW.h +4 -0
index b2d75e3..8eabfea 100644
@@ -124,6 +124,10 @@
 #define CONFIG_BITBANGMII
 
 #define MDIO_PORT			1		/* Port B */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define CONFIG_SYS_MDIO_PIN			0x00002000	/* PB18 */
 #define CONFIG_SYS_MDC_PIN			0x00001000	/* PB19 */
 #define MDIO_ACTIVE			(iop->pdir |=  CONFIG_SYS_MDIO_PIN)
include/configs/ZPC1900.h +4 -0
index 9cda3f9..dd09e83 100644
@@ -86,6 +86,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
 #define MDIO_READ		((iop->pdat &  0x00400000) != 0)
include/configs/ep8248.h +4 -0
index cb4185a..37f062f 100644
@@ -92,6 +92,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
include/configs/ep82xxm.h +4 -0
index 239ff67..fc6905b 100644
@@ -85,6 +85,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
include/configs/gw8260.h +4 -0
index 53a001d..6bf17b0 100644
@@ -212,6 +212,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT   2       /* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE    (iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE  (iop->pdir &= ~0x00400000)
 #define MDIO_READ     ((iop->pdat &  0x00400000) != 0)
include/configs/hymod.h +12 -0
index 284672b..328ccf2 100644
@@ -93,6 +93,10 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00040000	/* Pin 13 */
 # define MDIO_CLCK_PINMASK	0x00080000	/* Pin 12 */
 
@@ -110,6 +114,10 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00000040	/* Pin 25 */
 # define MDIO_CLCK_PINMASK	0x00000080	/* Pin 24 */
 
@@ -127,6 +135,10 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00000100	/* Pin 23 */
 # define MDIO_CLCK_PINMASK	0x00000200	/* Pin 22 */
 
include/configs/muas3001.h +4 -0
index c94daa3..f830aaf 100644
@@ -101,6 +101,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	0		/* Port A */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 
 #define CONFIG_SYS_MDIO_PIN	0x00200000	/* PA10 */
 #define CONFIG_SYS_MDC_PIN	0x00400000	/* PA9  */
include/configs/ppmc8260.h +4 -0
index ff7d614..31a0c2f 100644
@@ -182,6 +182,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
include/configs/sacsng.h +4 -0
index 0ab6fc3..d84f8ed 100644
@@ -179,6 +179,10 @@
  */
 
 #define MDIO_PORT	2	        /* Port A=0, B=1, C=2, D=3 */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x40000000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x40000000)
 #define MDIO_READ	((iop->pdat &  0x40000000) != 0)
include/configs/sbc8260.h +4 -0
index 26ed557..ec5b0f9 100644
@@ -201,6 +201,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
include/configs/sbc8560.h +4 -0
index a6b15f7..5a04950 100644
@@ -293,6 +293,10 @@
    * GPIO pins used for bit-banged MII communications
    */
   #define MDIO_PORT	2		/* Port C */
+  #define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+  #define MDC_DECLARE	MDIO_DECLARE
+
   #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
   #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
   #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
Signature · 1 line
1.6.3.3
#4 lore raw

PATCH v4 3/3 Update all board to support new bbmiiphy driver (with multibus support)

Luigi,

Quoted 27 lines · Luigi 'Comio' Mantellini
---
 include/configs/ISPAN.h      |    4 ++++
 include/configs/MPC8260ADS.h |    3 +++
 include/configs/MPC8266ADS.h |    4 ++++
 include/configs/MPC8560ADS.h |    4 ++++
 include/configs/Rattler.h    |    4 ++++
 include/configs/SBC8540.h    |    4 ++++
 include/configs/TQM8272.h    |    3 +++
 include/configs/VoVPN-GW.h   |    4 ++++
 include/configs/ZPC1900.h    |    4 ++++
 include/configs/ep8248.h     |    4 ++++
 include/configs/ep82xxm.h    |    4 ++++
 include/configs/gw8260.h     |    4 ++++
 include/configs/hymod.h      |   12 ++++++++++++
 include/configs/muas3001.h   |    4 ++++
 include/configs/ppmc8260.h   |    4 ++++
 include/configs/sacsng.h     |    4 ++++
 include/configs/sbc8260.h    |    4 ++++
 include/configs/sbc8560.h    |    4 ++++
 18 files changed, 78 insertions(+), 0 deletions(-)
include/configs/ISPAN.h +0 -0
index 6eb466a..02a188d 100644

include/configs/ISPAN.h line 89

Quoted 6 lines
include/configs/ISPAN.h +2 -0
@@ -84,6 +84,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		3		/* Port D */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
 

This, and all the others, are longer than 80 characters. Please remove 3 tabs from each and they'll fit

include/configs/ISPAN.h line 91

Quoted 2 lines
include/configs/ISPAN.h +1 -0
+#define MDC_DECLARE		MDIO_DECLARE
 

Please remove a tab so this aligns with MDIO_DECLARE. Apply globally.

<snip>

regards,
Ben

#5 lore raw

v4 cover New MIIPHYBB implementation with multi-bus support

In reply to Luigi 'Comio' Mantellini

Hi Luigi,

Sorry, I'm going to have to ask you to re-submit again :( There are a few things that need to be addressed

Quoted 46 lines · Luigi 'Comio' Mantellini

This patch rewrites the miiphybb ( Bit-banged MII bus driver ) in order to support an arbitrary number of mii buses. This feature is useful when your board uses different mii buses for different phys and all (or a part) of these buses are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board configuration file:

CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs to define at least the following macros:

MII_INIT      - Generic code to enable the MII bus (optional)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
MDC(v)        - Write v on the MDC pin

The previous macros make the driver compatible with the previous version (that didn't support the multi-bus).

When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill the bb_miiphy_buses[] array with a record for each required bus and declare the bb_miiphy_buses_num variable with the number of mii buses. The record (struct bb_miiphy_bus) has the following fields/callbacks (see miiphy.h for details):

char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin

int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

Quoted 9 lines

struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = "miibus#1", .init = b1_init, .mdio_active = b1_mdio_active, ... }, { .name = "miibus#2", .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
};
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /

                          sizeof(bb_miiphy_buses[0]);

Can you please copy this stuff into a README file (doc/README.bitbangMII maybe)? I'm afraid all this wonderful changelog information will be in a place that people won't look.
If it wasn't for other problems with this patch set, I'd do it myself.

Quoted 46 lines

Patch Changelog:

v1 -- First (broken) release
v2 -- Fix some typos and disable callbacks pointers relacation (if
CONFIG_RELOC_FIXUP_WORKS is not defined)
v3 -- Do not relocate NULL pointers
v4 -- Code Cleanup.

Luigi 'Comio' Mantellini (3):
New Bit-banged MII driver (MIIPHYBB) implementation with multi-bus
support.
Add bb_miiphy_init call before any ethernet bring-up code. Update all board to support new bbmiiphy driver (with multibus
support)

 drivers/net/phy/miiphybb.c   |  346 +++++++++++++++++++++++++++++-------------
 include/configs/ISPAN.h      |    4 +
 include/configs/MPC8260ADS.h |    3 +
 include/configs/MPC8266ADS.h |    4 +
 include/configs/MPC8560ADS.h |    4 +
 include/configs/Rattler.h    |    4 +
 include/configs/SBC8540.h    |    4 +
 include/configs/TQM8272.h    |    3 +
 include/configs/VoVPN-GW.h   |    4 +
 include/configs/ZPC1900.h    |    4 +
 include/configs/ep8248.h     |    4 +
 include/configs/ep82xxm.h    |    4 +
 include/configs/gw8260.h     |    4 +
 include/configs/hymod.h      |   12 ++
 include/configs/muas3001.h   |    4 +
 include/configs/ppmc8260.h   |    4 +
 include/configs/sacsng.h     |    4 +
 include/configs/sbc8260.h    |    4 +
 include/configs/sbc8560.h    |    4 +
 include/miiphy.h             |   25 +++-
 lib_arm/board.c              |    7 +
 lib_avr32/board.c            |    7 +
 lib_blackfin/board.c         |    7 +
 lib_i386/board.c             |    9 +-
 lib_m68k/board.c             |    7 +
 lib_mips/board.c             |    7 +
 lib_ppc/board.c              |    7 +
 lib_sh/board.c               |    7 +
 lib_sparc/board.c            |    7 +
 29 files changed, 408 insertions(+), 106 deletions(-)
Quoted 1 line

_______

Here are the real problems:

bwarren at bwarren-bldsrv$ CROSS_COMPILE=ppc_6xx- ./MAKEALL ppc
...
Configuring for ep8248 board...
board.c:87:20: error: miihpy.h: No such file or directory board.c:87:20: error: miihpy.h: No such file or directory board.c: In function 'board_init_r':
board.c:950: warning: implicit declaration of function 'bb_miiphy_init' make[1]: *** [board.o] Error 1
make: *** [lib_ppc/libppc.a] Error 2

And all sorts of other PPC boards fail too. Looks like a typo.

regards,
Ben