Skip to contentSkip to conversation

ARM pull request v3

U-Boot Tom Rix 7 participants 14 messages Oct 13, 2009 – Oct 17, 2009

lore
Share & tools
lore

Tom Rix

author
#0 lore raw

Wolfgang,

I have cleaned up the commits to arm/master-sync.

The cleanup is from doing a
git rev-list --reverse master..arm/master
Then working back from my notes to take only the commits were either misc arm or other arm pull requests. These were cherry picked on top of the current u-boot/master.

I ran the MAKEALL regression and the results look like what I posted on Sunday.

That said, it would be a good idea to wait a bit for others to review this list and pick up on anything that I missed.

I will be offline for about 10hrs and will fix any problems then.

Tom

The following changes since commit 14abfe361b3ed23b02f564e2f5d663e158cd5799:
Wolfgang Denk (1):
Merge branch 'master' of /home/wd/git/u-boot/custodians

are available in the git repository at:

git://git.denx.de/u-boot-arm master-sync

Daniel Gorsulowski (1):
at91: Update MEESC board support

Dirk Behme (1):
OMAP3 MMC: Fix warning dereferencing type-punned pointer

Olof Johansson (3):
OMAP3: Clean up whitespace in mux configs
SMC911X: Add chip auto detection
TI: OMAP3: Overo Tobi ethernet support

Prafulla Wadaskar (2):
Kirkwood: rd6281a: Add kwbimage build support
Kirkwood: mv88f6281gtw_ge: Add kwbimage build support

Sandeep Paulraj (9):
TI DaVinci: Remove references to SZ_xx
TI DaVinci: DM6446: Fix Compilation error in NAND mode TI DaVinci: DM646x: Initial Support for DM646x SOC TI DaVinci: DM355: Config Cleanup and Update
TI DaVinci DM365: Removing header file which does not exist
TI: DaVinci DM365: Minor config cleanup
TI: DaVinci DM646x: Update flag used to represent DM646x SOC's
TI: DaVinci: GPIO header file and definitions
TI: DaVinci DM365: Enabling network Support on DM365 EVM

Simon Kagstrom (2):
Support for the OpenRD base board
arm: Correct build with CONFIG_SYS_HUSH_PARSER set

Tom Rix (4):
OMAP3 Move cache routine to cache.S
Add support for Eukrea CPUAT91 SBC
Add support for Eukrea CPU9260/CPU9G20 SBC TI OMAP3 Use arm init sequence to initialize i2c

  MAINTAINERS                                |   10 +
  MAKEALL                                    |    6 +-
  Makefile                                   |   17 +
  board/Marvell/mv88f6281gtw_ge/config.mk    |    3 +
  board/Marvell/mv88f6281gtw_ge/kwbimage.cfg |  165 +++++++
  board/Marvell/openrd_base/Makefile         |   56 +++
  board/Marvell/openrd_base/config.mk        |   33 ++
  board/Marvell/openrd_base/kwbimage.cfg     |  168 +++++++
  board/Marvell/openrd_base/openrd_base.c    |  160 +++++++
  board/Marvell/openrd_base/openrd_base.h    |   46 ++
  board/Marvell/rd6281a/config.mk            |    3 +
  board/Marvell/rd6281a/kwbimage.cfg         |  167 +++++++
  board/davinci/dm365evm/dm365evm.c          |   44 ++-
  board/esd/meesc/meesc.c                    |   65 +++-
  board/eukrea/cpu9260/Makefile              |   59 +++
  board/eukrea/cpu9260/config.mk             |    1 +
  board/eukrea/cpu9260/cpu9260.c             |  220 +++++++++
  board/eukrea/cpu9260/led.c                 |  153 +++++++
  board/eukrea/cpuat91/Makefile              |   50 +++
  board/eukrea/cpuat91/config.mk             |    1 +
  board/eukrea/cpuat91/cpuat91.c             |   81 ++++
  board/logicpd/zoom1/zoom1.h                |  164 ++++----
  board/logicpd/zoom2/zoom2.h                |  188 ++++----
  board/overo/overo.c                        |   59 +++
  board/overo/overo.h                        |  645 
++++++++++++++--------------
  board/pandora/pandora.h                    |  662 
++++++++++++++--------------
  board/ti/beagle/beagle.h                   |  640 
++++++++++++++--------------
  board/ti/evm/evm.h                         |  662 
++++++++++++++--------------
  board/timll/devkit8000/devkit8000.h        |  628 
+++++++++++++-------------
  cpu/arm920t/at91rm9200/Makefile            |    5 +-
  cpu/arm920t/at91rm9200/ks8721.c            |  249 +++++++++++
  cpu/arm926ejs/at91/lowlevel_init.S         |    3 +-
  cpu/arm926ejs/davinci/Makefile             |    1 +
  cpu/arm926ejs/davinci/dm646x.c             |   41 ++
  cpu/arm926ejs/kirkwood/cpu.c               |    1 +
  cpu/arm_cortexa8/cpu.c                     |    2 +-
  cpu/arm_cortexa8/omap3/Makefile            |    2 +-
  cpu/arm_cortexa8/omap3/board.c             |    2 +-
  cpu/arm_cortexa8/omap3/cache.S             |  191 ++++++++
  cpu/arm_cortexa8/omap3/cache.c             |   95 ----
  cpu/arm_cortexa8/start.S                   |   85 ----
  drivers/mmc/omap3_mmc.c                    |   48 +--
  drivers/net/smc911x.c                      |   14 +-
  drivers/net/smc911x.h                      |    7 +-
  include/asm-arm/arch-davinci/emac_defs.h   |    4 +-
  include/asm-arm/arch-davinci/gpio_defs.h   |   53 +++
  include/asm-arm/arch-davinci/hardware.h    |   11 +
  include/asm-arm/arch-davinci/nand_defs.h   |    2 +-
  include/asm-arm/arch-omap3/mmc.h           |    7 +
  include/asm-arm/arch-omap3/omap3.h         |    2 +
  include/asm-arm/arch-omap3/sys_proto.h     |    2 +-
  include/configs/cpu9260.h                  |  453 +++++++++++++++++++
  include/configs/cpuat91.h                  |  228 ++++++++++
  include/configs/davinci_dm355evm.h         |   26 +-
  include/configs/davinci_dm365evm.h         |   11 +-
  include/configs/davinci_dvevm.h            |    6 +-
  include/configs/davinci_schmoogie.h        |    3 +-
  include/configs/davinci_sffsdr.h           |    3 +-
  include/configs/davinci_sonata.h           |    3 +-
  include/configs/devkit8000.h               |    1 +
  include/configs/meesc.h                    |   25 +-
  include/configs/omap3_beagle.h             |    1 +
  include/configs/omap3_evm.h                |    1 +
  include/configs/omap3_overo.h              |   18 +-
  include/configs/omap3_pandora.h            |    1 +
  include/configs/omap3_zoom1.h              |    1 +
  include/configs/omap3_zoom2.h              |    1 +
  include/configs/openrd_base.h              |  220 +++++++++
  include/ks8721.h                           |   78 ++++
  69 files changed, 4988 insertions(+), 2075 deletions(-)

create mode 100644 board/Marvell/mv88f6281gtw_ge/kwbimage.cfg create mode 100644 board/Marvell/openrd_base/Makefile create mode 100644 board/Marvell/openrd_base/config.mk create mode 100644 board/Marvell/openrd_base/kwbimage.cfg create mode 100644 board/Marvell/openrd_base/openrd_base.c create mode 100644 board/Marvell/openrd_base/openrd_base.h create mode 100644 board/Marvell/rd6281a/kwbimage.cfg create mode 100644 board/eukrea/cpu9260/Makefile create mode 100644 board/eukrea/cpu9260/config.mk create mode 100644 board/eukrea/cpu9260/cpu9260.c create mode 100644 board/eukrea/cpu9260/led.c create mode 100644 board/eukrea/cpuat91/Makefile create mode 100644 board/eukrea/cpuat91/config.mk create mode 100644 board/eukrea/cpuat91/cpuat91.c create mode 100644 cpu/arm920t/at91rm9200/ks8721.c create mode 100644 cpu/arm926ejs/davinci/dm646x.c create mode 100644 cpu/arm_cortexa8/omap3/cache.S delete mode 100644 cpu/arm_cortexa8/omap3/cache.c create mode 100644 include/asm-arm/arch-davinci/gpio_defs.h create mode 100644 include/configs/cpu9260.h
create mode 100644 include/configs/cpuat91.h
create mode 100644 include/configs/openrd_base.h create mode 100644 include/ks8721.h

#1 lore raw

Tom Rix a ?crit :

Quoted 59 lines

Wolfgang,

I have cleaned up the commits to arm/master-sync.

The cleanup is from doing a
git rev-list --reverse master..arm/master
Then working back from my notes to take only the commits were either misc arm or other arm pull requests. These were cherry picked on top of the current u-boot/master.

I ran the MAKEALL regression and the results look like what I posted on Sunday.

That said, it would be a good idea to wait a bit for others to review this list and pick up on anything that I missed.

I will be offline for about 10hrs and will fix any problems then.

Tom

The following changes since commit 14abfe361b3ed23b02f564e2f5d663e158cd5799:
Wolfgang Denk (1):
Merge branch 'master' of /home/wd/git/u-boot/custodians

are available in the git repository at:

git://git.denx.de/u-boot-arm master-sync

Daniel Gorsulowski (1):
at91: Update MEESC board support

Dirk Behme (1):
OMAP3 MMC: Fix warning dereferencing type-punned pointer

Olof Johansson (3):
OMAP3: Clean up whitespace in mux configs
SMC911X: Add chip auto detection
TI: OMAP3: Overo Tobi ethernet support

Prafulla Wadaskar (2):
Kirkwood: rd6281a: Add kwbimage build support
Kirkwood: mv88f6281gtw_ge: Add kwbimage build support

Sandeep Paulraj (9):
TI DaVinci: Remove references to SZ_xx
TI DaVinci: DM6446: Fix Compilation error in NAND mode TI DaVinci: DM646x: Initial Support for DM646x SOC TI DaVinci: DM355: Config Cleanup and Update
TI DaVinci DM365: Removing header file which does not exist
TI: DaVinci DM365: Minor config cleanup
TI: DaVinci DM646x: Update flag used to represent DM646x SOC's
TI: DaVinci: GPIO header file and definitions
TI: DaVinci DM365: Enabling network Support on DM365 EVM

Simon Kagstrom (2):
Support for the OpenRD base board
arm: Correct build with CONFIG_SYS_HUSH_PARSER set

Quoted 6 lines

Tom Rix (4):
OMAP3 Move cache routine to cache.S
Add support for Eukrea CPUAT91 SBC
Add support for Eukrea CPU9260/CPU9G20 SBC TI OMAP3 Use arm init sequence to initialize i2c

Tom,
Why this pull request does not include this[1] "sub pull request" from samsung repository?

[1]: http://lists.denx.de/pipermail/u-boot/2009-October/062364.html

Thanks

#2 lore raw
In reply to Tom Rix

Dear Tom Rix,

Quoted 155 lines · In message <[email protected]> you wrote:

Wolfgang,

I have cleaned up the commits to arm/master-sync.

The cleanup is from doing a
git rev-list --reverse master..arm/master
Then working back from my notes to take only the commits were either misc arm or other arm pull requests. These were cherry picked on top of the current u-boot/master.

I ran the MAKEALL regression and the results look like what I posted on Sunday.

That said, it would be a good idea to wait a bit for others to review this list and pick up on anything that I missed.

I will be offline for about 10hrs and will fix any problems then.

Tom

The following changes since commit 14abfe361b3ed23b02f564e2f5d663e158cd5799:
Wolfgang Denk (1):
Merge branch 'master' of /home/wd/git/u-boot/custodians

are available in the git repository at:

git://git.denx.de/u-boot-arm master-sync

Daniel Gorsulowski (1):
at91: Update MEESC board support

Dirk Behme (1):
OMAP3 MMC: Fix warning dereferencing type-punned pointer

Olof Johansson (3):
OMAP3: Clean up whitespace in mux configs
SMC911X: Add chip auto detection
TI: OMAP3: Overo Tobi ethernet support

Prafulla Wadaskar (2):
Kirkwood: rd6281a: Add kwbimage build support
Kirkwood: mv88f6281gtw_ge: Add kwbimage build support

Sandeep Paulraj (9):
TI DaVinci: Remove references to SZ_xx
TI DaVinci: DM6446: Fix Compilation error in NAND mode TI DaVinci: DM646x: Initial Support for DM646x SOC TI DaVinci: DM355: Config Cleanup and Update
TI DaVinci DM365: Removing header file which does not exist
TI: DaVinci DM365: Minor config cleanup
TI: DaVinci DM646x: Update flag used to represent DM646x SOC's
TI: DaVinci: GPIO header file and definitions
TI: DaVinci DM365: Enabling network Support on DM365 EVM

Simon Kagstrom (2):
Support for the OpenRD base board
arm: Correct build with CONFIG_SYS_HUSH_PARSER set

Tom Rix (4):
OMAP3 Move cache routine to cache.S
Add support for Eukrea CPUAT91 SBC
Add support for Eukrea CPU9260/CPU9G20 SBC TI OMAP3 Use arm init sequence to initialize i2c

  MAINTAINERS                                |   10 +
  MAKEALL                                    |    6 +-
  Makefile                                   |   17 +
  board/Marvell/mv88f6281gtw_ge/config.mk    |    3 +
  board/Marvell/mv88f6281gtw_ge/kwbimage.cfg |  165 +++++++
  board/Marvell/openrd_base/Makefile         |   56 +++
  board/Marvell/openrd_base/config.mk        |   33 ++
  board/Marvell/openrd_base/kwbimage.cfg     |  168 +++++++
  board/Marvell/openrd_base/openrd_base.c    |  160 +++++++
  board/Marvell/openrd_base/openrd_base.h    |   46 ++
  board/Marvell/rd6281a/config.mk            |    3 +
  board/Marvell/rd6281a/kwbimage.cfg         |  167 +++++++
  board/davinci/dm365evm/dm365evm.c          |   44 ++-
  board/esd/meesc/meesc.c                    |   65 +++-
  board/eukrea/cpu9260/Makefile              |   59 +++
  board/eukrea/cpu9260/config.mk             |    1 +
  board/eukrea/cpu9260/cpu9260.c             |  220 +++++++++
  board/eukrea/cpu9260/led.c                 |  153 +++++++
  board/eukrea/cpuat91/Makefile              |   50 +++
  board/eukrea/cpuat91/config.mk             |    1 +
  board/eukrea/cpuat91/cpuat91.c             |   81 ++++
  board/logicpd/zoom1/zoom1.h                |  164 ++++----
  board/logicpd/zoom2/zoom2.h                |  188 ++++----
  board/overo/overo.c                        |   59 +++
  board/overo/overo.h                        |  645 
++++++++++++++--------------
  board/pandora/pandora.h                    |  662 
++++++++++++++--------------
  board/ti/beagle/beagle.h                   |  640 
++++++++++++++--------------
  board/ti/evm/evm.h                         |  662 
++++++++++++++--------------
  board/timll/devkit8000/devkit8000.h        |  628 
+++++++++++++-------------
  cpu/arm920t/at91rm9200/Makefile            |    5 +-
  cpu/arm920t/at91rm9200/ks8721.c            |  249 +++++++++++
  cpu/arm926ejs/at91/lowlevel_init.S         |    3 +-
  cpu/arm926ejs/davinci/Makefile             |    1 +
  cpu/arm926ejs/davinci/dm646x.c             |   41 ++
  cpu/arm926ejs/kirkwood/cpu.c               |    1 +
  cpu/arm_cortexa8/cpu.c                     |    2 +-
  cpu/arm_cortexa8/omap3/Makefile            |    2 +-
  cpu/arm_cortexa8/omap3/board.c             |    2 +-
  cpu/arm_cortexa8/omap3/cache.S             |  191 ++++++++
  cpu/arm_cortexa8/omap3/cache.c             |   95 ----
  cpu/arm_cortexa8/start.S                   |   85 ----
  drivers/mmc/omap3_mmc.c                    |   48 +--
  drivers/net/smc911x.c                      |   14 +-
  drivers/net/smc911x.h                      |    7 +-
  include/asm-arm/arch-davinci/emac_defs.h   |    4 +-
  include/asm-arm/arch-davinci/gpio_defs.h   |   53 +++
  include/asm-arm/arch-davinci/hardware.h    |   11 +
  include/asm-arm/arch-davinci/nand_defs.h   |    2 +-
  include/asm-arm/arch-omap3/mmc.h           |    7 +
  include/asm-arm/arch-omap3/omap3.h         |    2 +
  include/asm-arm/arch-omap3/sys_proto.h     |    2 +-
  include/configs/cpu9260.h                  |  453 +++++++++++++++++++
  include/configs/cpuat91.h                  |  228 ++++++++++
  include/configs/davinci_dm355evm.h         |   26 +-
  include/configs/davinci_dm365evm.h         |   11 +-
  include/configs/davinci_dvevm.h            |    6 +-
  include/configs/davinci_schmoogie.h        |    3 +-
  include/configs/davinci_sffsdr.h           |    3 +-
  include/configs/davinci_sonata.h           |    3 +-
  include/configs/devkit8000.h               |    1 +
  include/configs/meesc.h                    |   25 +-
  include/configs/omap3_beagle.h             |    1 +
  include/configs/omap3_evm.h                |    1 +
  include/configs/omap3_overo.h              |   18 +-
  include/configs/omap3_pandora.h            |    1 +
  include/configs/omap3_zoom1.h              |    1 +
  include/configs/omap3_zoom2.h              |    1 +
  include/configs/openrd_base.h              |  220 +++++++++
  include/ks8721.h                           |   78 ++++
  69 files changed, 4988 insertions(+), 2075 deletions(-)

create mode 100644 board/Marvell/mv88f6281gtw_ge/kwbimage.cfg create mode 100644 board/Marvell/openrd_base/Makefile create mode 100644 board/Marvell/openrd_base/config.mk create mode 100644 board/Marvell/openrd_base/kwbimage.cfg create mode 100644 board/Marvell/openrd_base/openrd_base.c create mode 100644 board/Marvell/openrd_base/openrd_base.h create mode 100644 board/Marvell/rd6281a/kwbimage.cfg create mode 100644 board/eukrea/cpu9260/Makefile create mode 100644 board/eukrea/cpu9260/config.mk create mode 100644 board/eukrea/cpu9260/cpu9260.c create mode 100644 board/eukrea/cpu9260/led.c create mode 100644 board/eukrea/cpuat91/Makefile create mode 100644 board/eukrea/cpuat91/config.mk create mode 100644 board/eukrea/cpuat91/cpuat91.c create mode 100644 cpu/arm920t/at91rm9200/ks8721.c

Quoted 8 lines

create mode 100644 cpu/arm926ejs/davinci/dm646x.c create mode 100644 cpu/arm_cortexa8/omap3/cache.S delete mode 100644 cpu/arm_cortexa8/omap3/cache.c create mode 100644 include/asm-arm/arch-davinci/gpio_defs.h create mode 100644 include/configs/cpu9260.h create mode 100644 include/configs/cpuat91.h create mode 100644 include/configs/openrd_base.h create mode 100644 include/ks8721.h

Thanks. Applied locally. Will run some build tests and then push it out.

Best regards,

Wolfgang Denk

Signature · 7 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
After a heated argument on some trivial matter Nancy [Astor]  .  .  .
shouted,  ``If  I were your wife I would put poison in your coffee!''
Whereupon Winston Churchill with equal heat and  sincerity  answered,
``And if I were your husband I would drink it.''
#3 lore raw
Quoted 171 lines

Dear Tom Rix,

Quoted 16 lines · In message <[email protected]> you wrote:

Wolfgang,

I have cleaned up the commits to arm/master-sync.

The cleanup is from doing a
git rev-list --reverse master..arm/master
Then working back from my notes to take only the commits were either misc arm or other arm pull requests. These were cherry picked on top of the current u-boot/master.

I ran the MAKEALL regression and the results look like what I posted on Sunday.

That said, it would be a good idea to wait a bit for others to review this list and pick up on anything that I missed.

Quoted 6 lines

I will be offline for about 10hrs and will fix any problems then.

Tom

The following changes since commit

14abfe361b3ed23b02f564e2f5d663e158cd5799:

Quoted 133 lines

Wolfgang Denk (1):
Merge branch 'master' of /home/wd/git/u-boot/custodians

are available in the git repository at:

git://git.denx.de/u-boot-arm master-sync

Daniel Gorsulowski (1):
at91: Update MEESC board support

Dirk Behme (1):
OMAP3 MMC: Fix warning dereferencing type-punned pointer

Olof Johansson (3):
OMAP3: Clean up whitespace in mux configs
SMC911X: Add chip auto detection
TI: OMAP3: Overo Tobi ethernet support

Prafulla Wadaskar (2):
Kirkwood: rd6281a: Add kwbimage build support
Kirkwood: mv88f6281gtw_ge: Add kwbimage build support

Sandeep Paulraj (9):
TI DaVinci: Remove references to SZ_xx
TI DaVinci: DM6446: Fix Compilation error in NAND mode TI DaVinci: DM646x: Initial Support for DM646x SOC TI DaVinci: DM355: Config Cleanup and Update
TI DaVinci DM365: Removing header file which does not exist
TI: DaVinci DM365: Minor config cleanup
TI: DaVinci DM646x: Update flag used to represent DM646x SOC's
TI: DaVinci: GPIO header file and definitions
TI: DaVinci DM365: Enabling network Support on DM365 EVM

Simon Kagstrom (2):
Support for the OpenRD base board
arm: Correct build with CONFIG_SYS_HUSH_PARSER set

Tom Rix (4):
OMAP3 Move cache routine to cache.S
Add support for Eukrea CPUAT91 SBC
Add support for Eukrea CPU9260/CPU9G20 SBC TI OMAP3 Use arm init sequence to initialize i2c

  MAINTAINERS                                |   10 +
  MAKEALL                                    |    6 +-
  Makefile                                   |   17 +
  board/Marvell/mv88f6281gtw_ge/config.mk    |    3 +
  board/Marvell/mv88f6281gtw_ge/kwbimage.cfg |  165 +++++++
  board/Marvell/openrd_base/Makefile         |   56 +++
  board/Marvell/openrd_base/config.mk        |   33 ++
  board/Marvell/openrd_base/kwbimage.cfg     |  168 +++++++
  board/Marvell/openrd_base/openrd_base.c    |  160 +++++++
  board/Marvell/openrd_base/openrd_base.h    |   46 ++
  board/Marvell/rd6281a/config.mk            |    3 +
  board/Marvell/rd6281a/kwbimage.cfg         |  167 +++++++
  board/davinci/dm365evm/dm365evm.c          |   44 ++-
  board/esd/meesc/meesc.c                    |   65 +++-
  board/eukrea/cpu9260/Makefile              |   59 +++
  board/eukrea/cpu9260/config.mk             |    1 +
  board/eukrea/cpu9260/cpu9260.c             |  220 +++++++++
  board/eukrea/cpu9260/led.c                 |  153 +++++++
  board/eukrea/cpuat91/Makefile              |   50 +++
  board/eukrea/cpuat91/config.mk             |    1 +
  board/eukrea/cpuat91/cpuat91.c             |   81 ++++
  board/logicpd/zoom1/zoom1.h                |  164 ++++----
  board/logicpd/zoom2/zoom2.h                |  188 ++++----
  board/overo/overo.c                        |   59 +++
  board/overo/overo.h                        |  645
++++++++++++++--------------
  board/pandora/pandora.h                    |  662
++++++++++++++--------------
  board/ti/beagle/beagle.h                   |  640
++++++++++++++--------------
  board/ti/evm/evm.h                         |  662
++++++++++++++--------------
  board/timll/devkit8000/devkit8000.h        |  628
+++++++++++++-------------
  cpu/arm920t/at91rm9200/Makefile            |    5 +-
  cpu/arm920t/at91rm9200/ks8721.c            |  249 +++++++++++
  cpu/arm926ejs/at91/lowlevel_init.S         |    3 +-
  cpu/arm926ejs/davinci/Makefile             |    1 +
  cpu/arm926ejs/davinci/dm646x.c             |   41 ++
  cpu/arm926ejs/kirkwood/cpu.c               |    1 +
  cpu/arm_cortexa8/cpu.c                     |    2 +-
  cpu/arm_cortexa8/omap3/Makefile            |    2 +-
  cpu/arm_cortexa8/omap3/board.c             |    2 +-
  cpu/arm_cortexa8/omap3/cache.S             |  191 ++++++++
  cpu/arm_cortexa8/omap3/cache.c             |   95 ----
  cpu/arm_cortexa8/start.S                   |   85 ----
  drivers/mmc/omap3_mmc.c                    |   48 +--
  drivers/net/smc911x.c                      |   14 +-
  drivers/net/smc911x.h                      |    7 +-
  include/asm-arm/arch-davinci/emac_defs.h   |    4 +-
  include/asm-arm/arch-davinci/gpio_defs.h   |   53 +++
  include/asm-arm/arch-davinci/hardware.h    |   11 +
  include/asm-arm/arch-davinci/nand_defs.h   |    2 +-
  include/asm-arm/arch-omap3/mmc.h           |    7 +
  include/asm-arm/arch-omap3/omap3.h         |    2 +
  include/asm-arm/arch-omap3/sys_proto.h     |    2 +-
  include/configs/cpu9260.h                  |  453 +++++++++++++++++++
  include/configs/cpuat91.h                  |  228 ++++++++++
  include/configs/davinci_dm355evm.h         |   26 +-
  include/configs/davinci_dm365evm.h         |   11 +-
  include/configs/davinci_dvevm.h            |    6 +-
  include/configs/davinci_schmoogie.h        |    3 +-
  include/configs/davinci_sffsdr.h           |    3 +-
  include/configs/davinci_sonata.h           |    3 +-
  include/configs/devkit8000.h               |    1 +
  include/configs/meesc.h                    |   25 +-
  include/configs/omap3_beagle.h             |    1 +
  include/configs/omap3_evm.h                |    1 +
  include/configs/omap3_overo.h              |   18 +-
  include/configs/omap3_pandora.h            |    1 +
  include/configs/omap3_zoom1.h              |    1 +
  include/configs/omap3_zoom2.h              |    1 +
  include/configs/openrd_base.h              |  220 +++++++++
  include/ks8721.h                           |   78 ++++
  69 files changed, 4988 insertions(+), 2075 deletions(-)

create mode 100644 board/Marvell/mv88f6281gtw_ge/kwbimage.cfg create mode 100644 board/Marvell/openrd_base/Makefile create mode 100644 board/Marvell/openrd_base/config.mk create mode 100644 board/Marvell/openrd_base/kwbimage.cfg create mode 100644 board/Marvell/openrd_base/openrd_base.c create mode 100644 board/Marvell/openrd_base/openrd_base.h create mode 100644 board/Marvell/rd6281a/kwbimage.cfg create mode 100644 board/eukrea/cpu9260/Makefile create mode 100644 board/eukrea/cpu9260/config.mk create mode 100644 board/eukrea/cpu9260/cpu9260.c create mode 100644 board/eukrea/cpu9260/led.c create mode 100644 board/eukrea/cpuat91/Makefile create mode 100644 board/eukrea/cpuat91/config.mk create mode 100644 board/eukrea/cpuat91/cpuat91.c create mode 100644 cpu/arm920t/at91rm9200/ks8721.c

Quoted 8 lines

create mode 100644 cpu/arm926ejs/davinci/dm646x.c create mode 100644 cpu/arm_cortexa8/omap3/cache.S delete mode 100644 cpu/arm_cortexa8/omap3/cache.c create mode 100644 include/asm-arm/arch-davinci/gpio_defs.h create mode 100644 include/configs/cpu9260.h create mode 100644 include/configs/cpuat91.h create mode 100644 include/configs/openrd_base.h create mode 100644 include/ks8721.h

Quoted 2 lines

Thanks. Applied locally. Will run some build tests and then push it out.

Wolfgang,

I want to let you know that there will probably be some compilation warnings. These are patches for these. These have been sent to the list and ACK'ed by Tom and currently in my master. This will be part of my next pull request.

This pull request of mine will hopefully be the last for 2009.11.

Sandeep

Quoted 4 lines

Best regards,

Wolfgang Denk

#4 lore raw

Dear Sandeep,

Quoted 6 lines · in message <[email protected]> you…

I want to let you know that there will probably be some compilation warnings. These are patches for these. These have been sent to the list and ACK'ed by Tom and currently in my master. This will be part of my next pull request.

Thanks for the heads-up. Indeed there are lots of warning.

OK, so I will wait until Tom sends another pull request that includes these fixes.

Quoted 1 line

This pull request of mine will hopefully be the last for 2009.11.

Fine. Thanks again.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Diplomacy is the art of saying "nice doggy" until you can find a rock.
#5 lore raw
Quoted 9 lines · On Tue, 13 Oct 2009 16:51:14 +0200 Wolfgang Denk <[email protected]> wrote:
Quoted 4 lines

I want to let you know that there will probably be some compilation warnings. These are patches for these. These have been sent to the list and ACK'ed by Tom and currently in my master. This will be part of my next pull request.

Thanks for the heads-up. Indeed there are lots of warning.

OK, so I will wait until Tom sends another pull request that includes these fixes.

Tom: Perhaps you could pick up "[PATCH v3] arm926ejs: 8-byte align stack to avoid LDRD/STRD problems" for the ARM repo as well then?

I know it could go via Prafullas tree, but it's not really Marvell-specific, just fixes an issue for Sheevaplug and OpenRD. I also don't see how it could do any harm to other ARM boards.

// Simon

author
#6 lore raw
Quoted 12 lines · Simon Kagstrom
Quoted 8 lines · On Tue, 13 Oct 2009 16:51:14 +0200 Wolfgang Denk <[email protected]> wrote:
Quoted 4 lines

I want to let you know that there will probably be some compilation warnings. These are patches for these. These have been sent to the list and ACK'ed by Tom and currently in my master. This will be part of my next pull request.

Thanks for the heads-up. Indeed there are lots of warning.

OK, so I will wait until Tom sends another pull request that includes these fixes.

Quoted 7 lines

Tom: Perhaps you could pick up "[PATCH v3] arm926ejs: 8-byte align stack to avoid LDRD/STRD problems" for the ARM repo as well then?

I know it could go via Prafullas tree, but it's not really Marvell-specific, just fixes an issue for Sheevaplug and OpenRD. I also don't see how it could do any harm to other ARM boards.

Yes I think this fix is fine.
Did it make it into the marvell tree? Do you have a commit id I could cherry pick from? Else I will find it

Tom

Quoted 7 lines

// Simon
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#7 lore raw
Quoted 10 lines · On Wed, 14 Oct 2009 06:18:30 -0500 Tom Rix <[email protected]> wrote:
Quoted 6 lines

Tom: Perhaps you could pick up "[PATCH v3] arm926ejs: 8-byte align stack to avoid LDRD/STRD problems" for the ARM repo as well then?

I know it could go via Prafullas tree, but it's not really Marvell-specific, just fixes an issue for Sheevaplug and OpenRD. I also don't see how it could do any harm to other ARM boards.

Yes I think this fix is fine.
Did it make it into the marvell tree? Do you have a commit id I could cherry pick from? Else I will find it

I believe it's in the testing branch in Prafullas Marvell tree.

// Simon

#8 lore raw
In reply to Tom Rix

Tom Rix wrote:
...

Quoted 1 line

Olof Johansson (3):

...

Quoted 1 line

SMC911X: Add chip auto detection

This is broken [1] and doesn't work without

http://git.denx.de/?p=u-boot/u-boot-ti.git;a=commit;h=e7911214d5aee1ba5eb160327d5ff305c9e6ee5a

And while last re-organization of u-boot-ti

http://git.denx.de/?p=u-boot/u-boot-ti.git;a=commit;h=83fb7d7bb237cc7adae37e0e3328c203fd1b9ad1

was lost, but now is there again.

Maybe you like to cherry-pick both?

Best regards

Dirk

[1] http://lists.denx.de/pipermail/u-boot/2009-October/062301.html

#9 lore raw
Quoted 14 lines

Tom Rix wrote:
...

Quoted 1 line

Olof Johansson (3):

...

Quoted 1 line

SMC911X: Add chip auto detection

This is broken [1] and doesn't work without

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=e7911214d5aee1ba5eb160327d5ff305c9e6ee5a

Quoted 8 lines

And while last re-organization of u-boot-ti

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=83fb7d7bb237cc7adae37e0e3328c203fd1b9ad1

was lost, but now is there again.

Maybe you like to cherry-pick both?

I'll send out a pull request which will have these 2. I'll do that later today.

Quoted 6 lines

Best regards

Dirk

[1] http://lists.denx.de/pipermail/u-boot/2009-October/062301.html

#10 lore raw
Quoted 17 lines · Sandeep
Quoted 17 lines

Tom Rix wrote:
...

Quoted 1 line

Olof Johansson (3):

...

Quoted 1 line

SMC911X: Add chip auto detection

This is broken [1] and doesn't work without

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=e7911214d5aee1ba5eb160327d5ff305c9e6ee5a

And while last re-organization of u-boot-ti

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=83fb7d7bb237cc7adae37e0e3328c203fd1b9ad1

Quoted 6 lines
Quoted 3 lines

was lost, but now is there again.

Maybe you like to cherry-pick both?

I'll send out a pull request which will have these 2. I'll do that later today.

Sandeep: What's about this?

Tom: We need this in u-boot-arm before sending the pull request to Wolfgang. If we don't get a u-boot-ti pull request, at least we need the two above commits from u-boot-ti in u-boot-arm.

Many thanks and best regards

Dirk

#11 lore raw
Quoted 3 lines

Sandeep: What's about this?

Sent some days ago

http://article.gmane.org/gmane.comp.boot-loaders.u-boot/69770

Quoted 6 lines

Tom: We need this in u-boot-arm before sending the pull request to Wolfgang. If we don't get a u-boot-ti pull request, at least we need the two above commits from u-boot-ti in u-boot-arm.

Many thanks and best regards
Dirk

Thanks,
Sandeep

#12 lore raw
In reply to Dirk Behme
Quoted 23 lines · Dirk Behme
Quoted 13 lines · Sandeep
Quoted 13 lines

Tom Rix wrote:
...

Quoted 1 line

Olof Johansson (3):

...

Quoted 1 line

SMC911X: Add chip auto detection

This is broken [1] and doesn't work without

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=e7911214d5aee1ba5eb160327d5ff305c9e6ee5a

And while last re-organization of u-boot-ti

Quoted 8 lines
Quoted 6 lines

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=83fb7d7bb237cc7adae37e0e3328c203fd1b9ad1

was lost, but now is there again.

Maybe you like to cherry-pick both?

I'll send out a pull request which will have these 2. I'll do that later today.

Quoted 7 lines

Sandeep: What's about this?

Tom: We need this in u-boot-arm before sending the pull request to Wolfgang. If we don't get a u-boot-ti pull request, at least we need the two above commits from u-boot-ti in u-boot-arm.

Many thanks and best regards

Sorry for the delay.
I have been traveling.
I will catch up on the issues this weekend.
Tom

Quoted 6 lines

Dirk
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#13 lore raw
In reply to Dirk Behme
Quoted 23 lines · Dirk Behme
Quoted 13 lines · Sandeep
Quoted 13 lines

Tom Rix wrote:
...

Quoted 1 line

Olof Johansson (3):

...

Quoted 1 line

SMC911X: Add chip auto detection

This is broken [1] and doesn't work without

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=e7911214d5aee1ba5eb160327d5ff305c9e6ee5a

And while last re-organization of u-boot-ti

Quoted 8 lines
Quoted 6 lines

http://git.denx.de/?p=u-boot/u-boot-
ti.git;a=commit;h=83fb7d7bb237cc7adae37e0e3328c203fd1b9ad1

was lost, but now is there again.

Maybe you like to cherry-pick both?

I'll send out a pull request which will have these 2. I'll do that later today.

Quoted 7 lines

Sandeep: What's about this?

Tom: We need this in u-boot-arm before sending the pull request to Wolfgang. If we don't get a u-boot-ti pull request, at least we need the two above commits from u-boot-ti in u-boot-arm.

Many thanks and best regards

Dirk,
I have done the latest pull request.
Can you check that these or their equivalents have made it into arm/master-sync.

Tom

Quoted 6 lines

Dirk
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot