not supported broadcom (?) NIC revision

Hi,

I'v got server with built-in 9 NIC ports. Two ports are not recognized by any driver, I suppose it *should* be by tg3 or bnx2 Below is lspci info, not supported NIC are in slots 00:10.0 and 00:10.2
strange thing is that this vendor is described as Serverworks, but lspci says its Broadcom.

# grep 1166 include/linux/pci_ids.h
#define PCI_VENDOR_ID_SERVERWORKS         0x1166

Can someone help here ?

# lspci
00:00.0 Host bridge: Broadcom GCNB-LE Host Bridge (rev 32)
00:00.1 Host bridge: Broadcom GCNB-LE Host Bridge
00:02.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
00:0f.0 ISA bridge: Broadcom CSB5 South Bridge (rev 93)
00:0f.1 IDE interface: Broadcom CSB5 IDE Controller (rev 93)
00:0f.2 USB Controller: Broadcom OSB4/CSB5 OHCI USB Controller (rev 05)
00:0f.3 Host bridge: Broadcom CSB5 LPC bridge

00:10.0 Host bridge: Broadcom CIOB-E I/O Bridge with Gigabit Ethernet (rev 12) 00:10.2 Host bridge: Broadcom CIOB-E I/O Bridge with Gigabit Ethernet (rev 12)

02:02.0 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) 02:02.1 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) 02:04.0 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) 02:04.1 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) 03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 02) 03:00.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 02)

00:10.0 0600: 1166:0110 (rev 12)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

       Capabilities: [60] PCI-X non-bridge device
               Command: DPERE- ERO- RBC=512 OST=8
               Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge 

DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz-

00:10.2 0600: 1166:0110 (rev 12)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

       Capabilities: [60] PCI-X non-bridge device
               Command: DPERE- ERO- RBC=512 OST=8
               Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge 

DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz-

ServerWorks was bought by Broadcom many years ago.

These 2 are bridge devices and no driver is needed. I think the integrated ethernet device should be behind these bridges showing up as BCM5704 below.