Skip to contentSkip to conversation

"Reserved instruction in kernel code" on ath9k insertion

DISCUSSION Tomasz Chmielewski 4 participants 6 messages Oct 24, 2009 – Oct 26, 2009

lore
Share & tools
lore
#0 lore raw

When I do "modprobe ath9k" on ASUS-WL-500gP (MIPS) with _ath5k_ card (so, no ath9k hardware), it says "Reserved instruction in kernel code" - is it expected?

The kernel is 2.6.31.1.

# modprobe ath9k
[  165.440000] Reserved instruction in kernel code[#1]:
[  165.440000] Cpu 0
[  165.440000] $ 0   : 00000000 1000dc00 00000000 00000000
[  165.440000] $ 4   : c1135b20 00000001 c044e69c ffffffff
[  165.440000] $ 8   : 0000000a 8101f6d8 ffffffe0 0000002b
[  165.440000] $12   : 00000e44 00000006 80333ae8 5f657361
[  165.440000] $16   : 00000001 c1135ca4 80370000 81418000
[  165.440000] $20   : 00000000 00000000 00000000 004fe008
[  165.440000] $24   : 00000010 c1115118
[  165.440000] $28   : 81da6000 81da7ea8 7febead8 81418014
[  165.440000] Hi    : 00000000
[  165.440000] Lo    : 00000000
[  165.440000] epc   : c044e694 0xc044e694
[  165.440000]     Not tainted
[  165.440000] ra    : 81418014 ath9k_init+0x14/0xa4 [ath9k]
[  165.440000] Status: 1000dc03    KERNEL EXL IE
[  165.440000] Cause : 80800028
[  165.440000] PrId  : 00029006 (Broadcom BCM3302)
[  165.440000] Modules linked in: ath9k(+) aes_generic tun sch_sfq cls_fw sch_htb ipt_MASQUERADE iptable_nat nf_nat xt_MARK iptable_mangle ipt_ULOG xt_recent nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack xt_tcpudp iptable_filter ip_tables x_tables arc4 ecb ath5k mac80211 ath ohci_hcd cfg80211 uhci_hcd
[  165.440000] Process modprobe (pid: 1285, threadinfo=81da6000, task=81dc0048, tls=2aad96f0)
[  165.440000] Stack : 00000000 00000000 c1049988 000002a0 00000001 8000cda4 80330000 c1135ca4
[  165.440000]         0041ee08 2ac50000 005021a8 00000000 8004d59c 0029e597 0041ee08 2ac50000
[  165.440000]         00000001 c1135ca4 0041ee08 2ac50000 005021a8 8005fc84 0029f000 00000002
[  165.440000]         00408228 00400de0 004f1400 2aad8f08 00408228 00400de0 004f1400 2aad8f08
[  165.440000]         800035f0 800035f0 005021a8 004ff648 004fe008 00000000 00401090 00000000
[  165.440000]         ...
[  165.440000] Call Trace:
[  165.440000] [<8000cda4>] do_one_initcall+0x6c/0x204
[  165.440000] [<8004d59c>] blocking_notifier_call_chain+0x14/0x20
[  165.440000] [<8005fc84>] sys_init_module+0xe8/0x214
[  165.440000] [<800035f0>] stack_done+0x20/0x3c
[  165.440000] [<800035f0>] stack_done+0x20/0x3c
[  165.440000]
[  165.440000]
[  165.440000] Code: 00000000  00000000  00000000 <00003009> 005196a8  005196a8  00000002  00000000  005166b0
[  165.440000] Disabling lock debugging due to kernel taint
Segmentation fault
#
Signature · 2 lines
Tomasz Chmielewski
http://wpkg.org
#1 lore raw
Quoted 49 lines · Tomasz Chmielewski

When I do "modprobe ath9k" on ASUS-WL-500gP (MIPS) with _ath5k_ card (so, no ath9k hardware), it says "Reserved instruction in kernel code" - is it expected?

The kernel is 2.6.31.1.

# modprobe ath9k
[  165.440000] Reserved instruction in kernel code[#1]:
[  165.440000] Cpu 0
[  165.440000] $ 0   : 00000000 1000dc00 00000000 00000000
[  165.440000] $ 4   : c1135b20 00000001 c044e69c ffffffff
[  165.440000] $ 8   : 0000000a 8101f6d8 ffffffe0 0000002b
[  165.440000] $12   : 00000e44 00000006 80333ae8 5f657361
[  165.440000] $16   : 00000001 c1135ca4 80370000 81418000
[  165.440000] $20   : 00000000 00000000 00000000 004fe008
[  165.440000] $24   : 00000010 c1115118
[  165.440000] $28   : 81da6000 81da7ea8 7febead8 81418014
[  165.440000] Hi    : 00000000
[  165.440000] Lo    : 00000000
[  165.440000] epc   : c044e694 0xc044e694
[  165.440000]     Not tainted
[  165.440000] ra    : 81418014 ath9k_init+0x14/0xa4 [ath9k]
[  165.440000] Status: 1000dc03    KERNEL EXL IE
[  165.440000] Cause : 80800028
[  165.440000] PrId  : 00029006 (Broadcom BCM3302)
[  165.440000] Modules linked in: ath9k(+) aes_generic tun sch_sfq
cls_fw sch_htb ipt_MASQUERADE iptable_nat nf_nat xt_MARK iptable_mangle
ipt_ULOG xt_recent nf_conntrack_ipv4 nf_defrag_ipv4 xt_state
nf_conntrack xt_tcpudp iptable_filter ip_tables x_tables arc4 ecb ath5k
mac80211 ath ohci_hcd cfg80211 uhci_hcd
[  165.440000] Process modprobe (pid: 1285, threadinfo=81da6000,
task=81dc0048, tls=2aad96f0)
[  165.440000] Stack : 00000000 00000000 c1049988 000002a0 00000001
8000cda4 80330000 c1135ca4
[  165.440000]         0041ee08 2ac50000 005021a8 00000000 8004d59c
0029e597 0041ee08 2ac50000
[  165.440000]         00000001 c1135ca4 0041ee08 2ac50000 005021a8
8005fc84 0029f000 00000002
[  165.440000]         00408228 00400de0 004f1400 2aad8f08 00408228
00400de0 004f1400 2aad8f08
[  165.440000]         800035f0 800035f0 005021a8 004ff648 004fe008
00000000 00401090 00000000
[  165.440000]         ...
[  165.440000] Call Trace:
[  165.440000] [<8000cda4>] do_one_initcall+0x6c/0x204
[  165.440000] [<8004d59c>] blocking_notifier_call_chain+0x14/0x20
[  165.440000] [<8005fc84>] sys_init_module+0xe8/0x214
[  165.440000] [<800035f0>] stack_done+0x20/0x3c
Quoted 8 lines
[  165.440000] [<800035f0>] stack_done+0x20/0x3c
[  165.440000]
[  165.440000]
[  165.440000] Code: 00000000  00000000  00000000 <00003009> 005196a8 
005196a8  00000002  00000000  005166b0
[  165.440000] Disabling lock debugging due to kernel taint
Segmentation fault
#

Is that the start of the error dump? A BUG() statement places an illegal instruction in the code. Is that the case here?

#2 lore raw
Quoted 2 lines · Larry Finger
Quoted 2 lines
# modprobe ath9k
[  165.440000] Reserved instruction in kernel code[#1]:

(...)

Quoted 6 lines
Quoted 4 lines
[  165.440000] Code: 00000000  00000000  00000000 <00003009> 005196a8 005196a8  00000002  00000000  005166b0
[  165.440000] Disabling lock debugging due to kernel taint

Segmentation fault
#

Is that the start of the error dump?

Yes - as I do "modprobe", it starts to print the dump. Then, modprobe segfaults.

Quoted 2 lines

A BUG() statement places an
illegal instruction in the code. Is that the case here?

I have no idea.

Signature · 2 lines
Tomasz Chmielewski
http://wpkg.org
#3 lore raw
In reply to Tomasz Chmielewski
Quoted 3 lines · Tomasz Chmielewski

When I do "modprobe ath9k" on ASUS-WL-500gP (MIPS) with _ath5k_ card (so, no ath9k hardware), it says "Reserved instruction in kernel code" - is it expected?

No.

Quoted 18 lines

The kernel is 2.6.31.1.

# modprobe ath9k
[  165.440000] Reserved instruction in kernel code[#1]:
[  165.440000] Cpu 0
[  165.440000] $ 0   : 00000000 1000dc00 00000000 00000000
[  165.440000] $ 4   : c1135b20 00000001 c044e69c ffffffff
[  165.440000] $ 8   : 0000000a 8101f6d8 ffffffe0 0000002b
[  165.440000] $12   : 00000e44 00000006 80333ae8 5f657361
[  165.440000] $16   : 00000001 c1135ca4 80370000 81418000
[  165.440000] $20   : 00000000 00000000 00000000 004fe008
[  165.440000] $24   : 00000010 c1115118
[  165.440000] $28   : 81da6000 81da7ea8 7febead8 81418014
[  165.440000] Hi    : 00000000
[  165.440000] Lo    : 00000000
[  165.440000] epc   : c044e694 0xc044e694
[  165.440000]     Not tainted

This says not tainted.

Quoted 1 line

[  165.440000] ra    : 81418014 ath9k_init+0x14/0xa4 [ath9k]

So ath9k_init() should run whether you have the hardware or not since you modprobed' ath9k. For ath9k this consists of running:

ath_rate_control_register()
ath9k_debug_create_root()
ath_pci_init()
ath_ahb_init()

debugfs stuff should be a no-op unless you have enabled CONFIG_ATH9k_DEBUG. So even ath_pci_init() should succeed even if you do not have any of the claimed PCI devices, the only way that fails is if pci_register_driver() fails.

More below.

Quoted 24 lines

[  165.440000] Status: 1000dc03    KERNEL EXL IE
[  165.440000] Cause : 80800028
[  165.440000] PrId  : 00029006 (Broadcom BCM3302)
[  165.440000] Modules linked in: ath9k(+) aes_generic tun sch_sfq cls_fw sch_htb ipt_MASQUERADE iptable_nat nf_nat xt_MARK iptable_mangle ipt_ULOG xt_recent nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack xt_tcpudp iptable_filter ip_tables x_tables arc4 ecb ath5k mac80211 ath ohci_hcd cfg80211 uhci_hcd
[  165.440000] Process modprobe (pid: 1285, threadinfo=81da6000, task=81dc0048, tls=2aad96f0)
[  165.440000] Stack : 00000000 00000000 c1049988 000002a0 00000001 8000cda4 80330000 c1135ca4
[  165.440000]         0041ee08 2ac50000 005021a8 00000000 8004d59c 0029e597 0041ee08 2ac50000
[  165.440000]         00000001 c1135ca4 0041ee08 2ac50000 005021a8 8005fc84 0029f000 00000002
[  165.440000]         00408228 00400de0 004f1400 2aad8f08 00408228 00400de0 004f1400 2aad8f08
[  165.440000]         800035f0 800035f0 005021a8 004ff648 004fe008 00000000 00401090 00000000
[  165.440000]         ...
[  165.440000] Call Trace:
[  165.440000] [<8000cda4>] do_one_initcall+0x6c/0x204
[  165.440000] [<8004d59c>] blocking_notifier_call_chain+0x14/0x20

Quoted 8 lines

[  165.440000] [<8005fc84>] sys_init_module+0xe8/0x214
[  165.440000] [<800035f0>] stack_done+0x20/0x3c
[  165.440000] [<800035f0>] stack_done+0x20/0x3c
[  165.440000]
[  165.440000]
[  165.440000] Code: 00000000  00000000  00000000 <00003009> 005196a8 005196a8  00000002  00000000  005166b0
[  165.440000] Disabling lock debugging due to kernel taint

But this says kernel taint.

Quoted 2 lines

Segmentation fault
#

So I'm not 100% sure but I believe "Reserved instruction in kernel code" means some instruction is trying to be run on your mips board for which your actual CPU has no support for, which could happen if you cross compiled code to your target with an incorrect toolchain. At least that is how someone interpreted this on some old madwifi ticket when someone ran into this [1]. The failure actually comes from the mips do_ri() call [2] but cannot confirm whether or not the interpretation is correct. To confirm you may want to check with the linux-mips list.

[1] http://madwifi-project.org/ticket/994
[2] http://lxr.linux.no/#linux+v2.6.31/arch/mips/kernel/traps.c#L806

Luis

#4 lore raw
Quoted 27 lines · Luis R. Rodriguez
Quoted 3 lines · Tomasz Chmielewski

When I do "modprobe ath9k" on ASUS-WL-500gP (MIPS) with _ath5k_ card (so, no ath9k hardware), it says "Reserved instruction in kernel code" - is it expected?

No.

Quoted 18 lines

The kernel is 2.6.31.1.

# modprobe ath9k
[  165.440000] Reserved instruction in kernel code[#1]:
[  165.440000] Cpu 0
[  165.440000] $ 0   : 00000000 1000dc00 00000000 00000000
[  165.440000] $ 4   : c1135b20 00000001 c044e69c ffffffff
[  165.440000] $ 8   : 0000000a 8101f6d8 ffffffe0 0000002b
[  165.440000] $12   : 00000e44 00000006 80333ae8 5f657361
[  165.440000] $16   : 00000001 c1135ca4 80370000 81418000
[  165.440000] $20   : 00000000 00000000 00000000 004fe008
[  165.440000] $24   : 00000010 c1115118
[  165.440000] $28   : 81da6000 81da7ea8 7febead8 81418014
[  165.440000] Hi    : 00000000
[  165.440000] Lo    : 00000000
[  165.440000] epc   : c044e694 0xc044e694
[  165.440000]     Not tainted

This says not tainted.

(...)

Quoted 3 lines
Quoted 1 line
[  165.440000] Disabling lock debugging due to kernel taint

But this says kernel taint.

Yep, I saw this as well.

About every oops or panic on this hardware says "Disabling lock debugging due to kernel taint", no idea why.

Signature · 2 lines
Tomasz Chmielewski
http://wpkg.org
#5 lore raw
Quoted 6 lines · Tomasz Chmielewski
Quoted 3 lines
Quoted 1 line
[  165.440000]     Not tainted

This says not tainted.

(...)

Quoted 8 lines
Quoted 3 lines
Quoted 1 line
[  165.440000] Disabling lock debugging due to kernel taint

But this says kernel taint.

Yep, I saw this as well.

About every oops or panic on this hardware says "Disabling lock debugging due to kernel taint", no idea why.

Umm, oopsing itself taints the kernel, so _after/during_ the oops lock debugging _gets_ disabled.

johannes