Skip to contentSkip to conversation

Initial support for Orion5x SoC and EDMini board

PATCH New Albert Aribaud 3 participants 6 messages Nov 14, 2009 Kbuild

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Initial support for Orion5x SoC and EDMini board

This patch adds initial u-boot support for the Marvell orion5x SoC and the LAcie ED Mini V2 board--support is limited to serial, flash and environment. Further support will be added as devices common with kirkwood are made useable across SoCs.

---
 Makefile                               |    3 +
 board/Marvell/edminiv2/Makefile        |   51 +++++
 board/Marvell/edminiv2/config.mk       |   25 +++
 board/Marvell/edminiv2/edminiv2.c      |  165 ++++++++++++++++
 board/Marvell/edminiv2/edminiv2.h      |   39 ++++
 cpu/arm926ejs/orion5x/Makefile         |   52 +++++
 cpu/arm926ejs/orion5x/cpu.c            |  339 ++++++++++++++++++++++++++++++++
 cpu/arm926ejs/orion5x/dram.c           |   61 ++++++
 cpu/arm926ejs/orion5x/mpp.c            |   88 ++++++++
 cpu/arm926ejs/orion5x/timer.c          |  171 ++++++++++++++++
 drivers/serial/serial.c                |    3 +
 include/asm-arm/arch-orion5x/88f5182.h |   40 ++++
 include/asm-arm/arch-orion5x/cpu.h     |  213 ++++++++++++++++++++
 include/asm-arm/arch-orion5x/gpio.h    |   53 +++++
 include/asm-arm/arch-orion5x/mpp.h     |  122 ++++++++++++
 include/asm-arm/arch-orion5x/orion5x.h |   67 +++++++
 include/configs/edminiv2.h             |  158 +++++++++++++++
 17 files changed, 1650 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/edminiv2/Makefile
 create mode 100644 board/Marvell/edminiv2/config.mk
 create mode 100644 board/Marvell/edminiv2/edminiv2.c
 create mode 100644 board/Marvell/edminiv2/edminiv2.h
 create mode 100644 cpu/arm926ejs/orion5x/Makefile
 create mode 100644 cpu/arm926ejs/orion5x/cpu.c
 create mode 100644 cpu/arm926ejs/orion5x/dram.c
 create mode 100644 cpu/arm926ejs/orion5x/mpp.c
 create mode 100644 cpu/arm926ejs/orion5x/timer.c
 create mode 100644 include/asm-arm/arch-orion5x/88f5182.h
 create mode 100644 include/asm-arm/arch-orion5x/cpu.h
 create mode 100644 include/asm-arm/arch-orion5x/gpio.h
 create mode 100644 include/asm-arm/arch-orion5x/mpp.h
 create mode 100644 include/asm-arm/arch-orion5x/orion5x.h
 create mode 100644 include/configs/edminiv2.h
Makefile +3 -0
index bcb3fe9..60f9140 100644
@@ -2951,6 +2951,9 @@ davinci_dm365evm_config :	unconfig
 davinci_dm6467evm_config :	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs dm6467evm davinci davinci
 
+edminiv2_config: unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell orion5x
+
 imx27lite_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs imx27lite logicpd mx27
 
board/Marvell/edminiv2/Makefile new file +51 -0

51 lines not on this page · raw message

board/Marvell/edminiv2/config.mk new file +25 -0
new file mode 100644
index 0000000..a4ea769
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
board/Marvell/edminiv2/edminiv2.c new file +165 -0

165 lines not on this page · raw message

board/Marvell/edminiv2/edminiv2.h new file +39 -0
new file mode 100644
index 0000000..77a108e
@@ -0,0 +1,39 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __EDMINIV2_H
+#define __EDMINIV2_H
+
+#define EDMINIV2_OE_LOW		(~(0))
+#define EDMINIV2_OE_VAL_LOW		(1 << 29)	/* USB_PWEN low */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG		10
+#define MV88E1116_CPRSP_CR3_REG		21
+#define MV88E1116_MAC_CTRL_REG		21
+#define MV88E1116_PGADR_REG		22
+#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
+
+#endif /* __EDMINIV2_H */
cpu/arm926ejs/orion5x/Makefile new file +52 -0

52 lines not on this page · raw message

cpu/arm926ejs/orion5x/cpu.c new file +339 -0

339 lines not on this page · raw message

cpu/arm926ejs/orion5x/dram.c new file +61 -0

61 lines not on this page · raw message

cpu/arm926ejs/orion5x/mpp.c new file +88 -0

88 lines not on this page · raw message

cpu/arm926ejs/orion5x/timer.c new file +171 -0

171 lines not on this page · raw message

drivers/serial/serial.c +3 -0
index dd5f332..18686a2 100644
@@ -30,6 +30,9 @@
 #ifdef CONFIG_KIRKWOOD
 #include <asm/arch/kirkwood.h>
 #endif
+#ifdef CONFIG_ORION5X
+#include <asm/arch/orion5x.h>
+#endif
 
 #if defined (CONFIG_SERIAL_MULTI)
 #include <serial.h>
include/asm-arm/arch-orion5x/88f5182.h new file +40 -0
new file mode 100644
index 0000000..1dfdb24
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood 88F6182 support which is
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * Header file for Feroceon CPU core 88F5182 SOC.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_88F5182_H
+#define _CONFIG_88F5182_H
+
+/* SOC specific definations */
+#define F88F5182_REGS_PHYS_BASE		0xf1000000
+#define ORION5X_REGS_PHY_BASE		F88F5182_REGS_PHYS_BASE
+
+/* TCLK Core Clock defination */
+#define CONFIG_SYS_TCLK			166000000 /* 166MHz */
+
+#endif /* _CONFIG_88F5182_H */
include/asm-arm/arch-orion5x/cpu.h new file +213 -0

213 lines not on this page · raw message

include/asm-arm/arch-orion5x/gpio.h new file +53 -0

53 lines not on this page · raw message

include/asm-arm/arch-orion5x/mpp.h new file +122 -0

122 lines not on this page · raw message

include/asm-arm/arch-orion5x/orion5x.h new file +67 -0

67 lines not on this page · raw message

include/configs/edminiv2.h new file +158 -0

158 lines not on this page · raw message

Signature · 1 line
1.6.4.4
#1 lore raw

PATCH 1/1 Initial support for Orion5x SoC and EDMini board

Quoted 32 lines · Albert Aribaud

This patch adds initial u-boot support for the Marvell orion5x SoC and the LAcie ED Mini V2 board--support is limited to serial, flash and environment. Further support will be added as devices common with kirkwood are made useable across SoCs.

---
 Makefile                               |    3 +
 board/Marvell/edminiv2/Makefile        |   51 +++++
 board/Marvell/edminiv2/config.mk       |   25 +++
 board/Marvell/edminiv2/edminiv2.c      |  165 ++++++++++++++++
 board/Marvell/edminiv2/edminiv2.h      |   39 ++++
 cpu/arm926ejs/orion5x/Makefile         |   52 +++++
 cpu/arm926ejs/orion5x/cpu.c            |  339 ++++++++++++++++++++++++++++++++
 cpu/arm926ejs/orion5x/dram.c           |   61 ++++++
 cpu/arm926ejs/orion5x/mpp.c            |   88 ++++++++
 cpu/arm926ejs/orion5x/timer.c          |  171 ++++++++++++++++
 drivers/serial/serial.c                |    3 +
 include/asm-arm/arch-orion5x/88f5182.h |   40 ++++
 include/asm-arm/arch-orion5x/cpu.h     |  213 ++++++++++++++++++++
 include/asm-arm/arch-orion5x/gpio.h    |   53 +++++
 include/asm-arm/arch-orion5x/mpp.h     |  122 ++++++++++++
 include/asm-arm/arch-orion5x/orion5x.h |   67 +++++++
 include/configs/edminiv2.h             |  158 +++++++++++++++
 17 files changed, 1650 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/edminiv2/Makefile
 create mode 100644 board/Marvell/edminiv2/config.mk
 create mode 100644 board/Marvell/edminiv2/edminiv2.c
 create mode 100644 board/Marvell/edminiv2/edminiv2.h
 create mode 100644 cpu/arm926ejs/orion5x/Makefile
 create mode 100644 cpu/arm926ejs/orion5x/cpu.c
 create mode 100644 cpu/arm926ejs/orion5x/dram.c
Quoted 8 lines
 create mode 100644 cpu/arm926ejs/orion5x/mpp.c
 create mode 100644 cpu/arm926ejs/orion5x/timer.c
 create mode 100644 include/asm-arm/arch-orion5x/88f5182.h
 create mode 100644 include/asm-arm/arch-orion5x/cpu.h
 create mode 100644 include/asm-arm/arch-orion5x/gpio.h
 create mode 100644 include/asm-arm/arch-orion5x/mpp.h
 create mode 100644 include/asm-arm/arch-orion5x/orion5x.h
 create mode 100644 include/configs/edminiv2.h

For this pass, I ran the linux kernel checkpatch.pl against your patch. I get

total: 180 errors, 26 warnings, 1662 lines checked

In general, the patch should have no errors or warnings. Please fix the checkpatch issues.

Tom

#2 lore raw

PATCH 1/1 Initial support for Orion5x SoC and EDMini board

In reply to Albert Aribaud
Quoted 10 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, November 14, 2009 6:32 AM
To: U-Boot at lists.denx.de
Subject: [U-Boot] [PATCH] Initial support for Orion5x SoC and EDMini board

Quoted 7 lines

This patch adds initial u-boot support for the Marvell orion5x SoC and the LAcie ED Mini V2 board--support is limited to serial, flash and environment. Further support will be added as devices common with kirkwood are made useable across SoCs.

---

Hi Albert

Please break this patch in to small pieces

Quoted 5 lines
 Makefile                               |    3 +
 board/Marvell/edminiv2/Makefile        |   51 +++++
 board/Marvell/edminiv2/config.mk       |   25 +++
 board/Marvell/edminiv2/edminiv2.c      |  165 ++++++++++++++++
 board/Marvell/edminiv2/edminiv2.h      |   39 ++++

Pls edit MAKEALL and Maintainers files too for new board support

Arm: add Edminv2 board support (orion5x based)

Quoted 4 lines
 cpu/arm926ejs/orion5x/Makefile         |   52 +++++
 cpu/arm926ejs/orion5x/cpu.c            |  339
++++++++++++++++++++++++++++++++
 cpu/arm926ejs/orion5x/dram.c           |   61 ++++++
Quoted 8 lines
 cpu/arm926ejs/orion5x/mpp.c            |   88 ++++++++
 cpu/arm926ejs/orion5x/timer.c          |  171 ++++++++++++++++
 drivers/serial/serial.c                |    3 +
 include/asm-arm/arch-orion5x/88f5182.h |   40 ++++
 include/asm-arm/arch-orion5x/cpu.h     |  213 ++++++++++++++++++++
 include/asm-arm/arch-orion5x/gpio.h    |   53 +++++
 include/asm-arm/arch-orion5x/mpp.h     |  122 ++++++++++++
 include/asm-arm/arch-orion5x/orion5x.h |   67 +++++++

Break this in to basic orion5x Soc support patch And individual drivers patches like gpio, uart, etc..

Quoted 41 lines
 include/configs/edminiv2.h             |  158 +++++++++++++++
 17 files changed, 1650 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/edminiv2/Makefile
 create mode 100644 board/Marvell/edminiv2/config.mk
 create mode 100644 board/Marvell/edminiv2/edminiv2.c
 create mode 100644 board/Marvell/edminiv2/edminiv2.h
 create mode 100644 cpu/arm926ejs/orion5x/Makefile
 create mode 100644 cpu/arm926ejs/orion5x/cpu.c
 create mode 100644 cpu/arm926ejs/orion5x/dram.c
 create mode 100644 cpu/arm926ejs/orion5x/mpp.c
 create mode 100644 cpu/arm926ejs/orion5x/timer.c
 create mode 100644 include/asm-arm/arch-orion5x/88f5182.h
 create mode 100644 include/asm-arm/arch-orion5x/cpu.h
 create mode 100644 include/asm-arm/arch-orion5x/gpio.h
 create mode 100644 include/asm-arm/arch-orion5x/mpp.h
 create mode 100644 include/asm-arm/arch-orion5x/orion5x.h
 create mode 100644 include/configs/edminiv2.h
Makefile +0 -0
index bcb3fe9..60f9140 100644
@@ -2951,6 +2951,9 @@ davinci_dm365evm_config :       unconfig
 davinci_dm6467evm_config :   unconfig
      @$(MKCONFIG) $(@:_config=) arm arm926ejs dm6467evm

davinci davinci

Makefile +2 -0
+edminiv2_config: unconfig
+     @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=)

Marvell orion5x

Makefile +1 -0
+
 imx27lite_config:    unconfig
      @$(MKCONFIG) $(@:_config=) arm arm926ejs imx27lite logicpd mx27
board/Marvell/edminiv2/Makefile new file +0 -0
new file mode 100644
index 0000000..2e6d305

board/Marvell/edminiv2/Makefile line 4

Quoted 4 lines
board/Marvell/edminiv2/Makefile new file +4 -0
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>

This is copy paste mistake, pls correct in all files
You can keep my reference, i.e. based on (ref: boards/Marvell/openrd_base/openrd_base.c)

Quoted 56 lines
board/Marvell/edminiv2/Makefile new file +40 -0
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.        See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB  = $(obj)lib$(BOARD).a
+
+COBJS        := edminiv2.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS        := $(addprefix $(obj),$(SOBJS))
+
+$(LIB):      $(obj).depend $(OBJS) $(SOBJS)
+     $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+     rm -f $(SOBJS) $(OBJS)
+
+distclean:   clean
+     rm -f $(LIB) core *.bak .depend
+
+#############################################################

############

board/Marvell/edminiv2/Makefile new file +7 -0
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#############################################################

############

board/Marvell/edminiv2/config.mk new file +0 -0
new file mode 100644
index 0000000..a4ea769

board/Marvell/edminiv2/config.mk line 4

Quoted 4 lines
board/Marvell/edminiv2/config.mk new file +4 -0
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>

Ditto

Quoted 11 lines
board/Marvell/edminiv2/config.mk new file +11 -0
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of

board/Marvell/edminiv2/config.mk line 25

Quoted 10 lines
board/Marvell/edminiv2/config.mk new file +10 -0
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000

Is this valid for your board? BTW: how much DRAM you have on this board?

board/Marvell/edminiv2/edminiv2.c line 4

Quoted 11 lines
board/Marvell/edminiv2/edminiv2.c new file +4 -0
new file mode 100644
index 0000000..f23de0e
@@ -0,0 +1,165 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>

Ditto

Quoted 76 lines
board/Marvell/edminiv2/edminiv2.c new file +31 -0
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/orion5x.h>
+#include <asm/arch/mpp.h>
+#include "edminiv2.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if defined(CONFIG_FLASH_CFI_LEGACY)
+#include <flash.h>
+ulong board_flash_get_legacy (ulong base, int banknum,

flash_info_t * info)

board/Marvell/edminiv2/edminiv2.c new file +44 -0
+{
+     int sectsz[] = CONFIG_SYS_FLASH_SECTSZ;
+     int sect;
+
+     if (base != CONFIG_SYS_FLASH_BASE)
+             return 0;
+
+     info->size = 0;
+     info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
+     for (sect=0; sect<CONFIG_SYS_MAX_FLASH_SECT; sect++) {
+             info->start[sect] = base+info->size;
+             info->size += sectsz[sect];
+     }
+     info->flash_id                  = 0x01000000;
+     info->portwidth = FLASH_CFI_8BIT;
+     info->chipwidth = FLASH_CFI_BY8;
+     info->buffer_size = 32;
+     info->erase_blk_tout = 16384;
+     info->write_tout = 2;
+     info->buffer_write_tout = 5;
+     info->vendor = CFI_CMDSET_AMD_LEGACY;
+     info->cmd_reset= 0xF0;
+     info->interface= FLASH_CFI_X8;
+     info->legacy_unlock = 0;
+     info->manufacturer_id = 0xC2;
+     info->device_id = 0xBA;
+     info->device_id2= 0;
+
+     info->ext_addr = 0;
+     info->cfi_version = 0x3133;
+     info->cfi_offset = 0x0000;
+     info->addr_unlock1 = 0x00000555;
+     info->addr_unlock2 = 0x000002AA;
+     info->name = "MX29LV400CB";
+
+     return 1;
+}
+#endif                               /* CONFIG_SYS_FLASH_CFI */
+
+int board_init(void)
+{
+     /*
+      * default gpio configuration
+      * There are maximum 64 gpios controlled through 2 sets
Quoted 1 line

of registers

I don't think there are 64 GPIOs in orion5x

board/Marvell/edminiv2/edminiv2.c line 82

Quoted 3 lines
board/Marvell/edminiv2/edminiv2.c new file +3 -0
+      * the  below configuration configures mainly initial LED status
+      */
+     orion5x_config_gpio(EDMINIV2_OE_VAL_LOW, EDMINIV2_OE_LOW);

You can eliminate LOW here, since mpps less than 32

Quoted 90 lines
board/Marvell/edminiv2/edminiv2.c new file +83 -0
+
+     /* Multi-Purpose Pins Functionality configuration */
+     u32 edminiv2_mpp_config[] = {
+             MPP0_GPIO,
+             MPP1_GPIO,
+             MPP2_GPIO,
+             MPP3_GPIO,
+             MPP4_GPIO,
+             MPP5_GPIO,
+             MPP6_GPIO,
+             MPP7_GPIO,
+             MPP8_GPIO,
+             MPP9_GPIO,
+             MPP10_GPIO,
+             MPP11_GPIO,
+             MPP12_SATA0_PRESENTn,
+             MPP13_SATA1_PRESENTn,
+             MPP14_SATA0_ACTn,
+             MPP15_SATA1_ACTn,
+             MPP16_GPIO,
+             MPP17_GPIO,
+             MPP18_GPIO,
+             MPP19_GPIO,
+             0
+     };
+     orion5x_mpp_conf(edminiv2_mpp_config);
+
+     /*
+      * arch number of board
+      */
+     gd->bd->bi_arch_number = MACH_TYPE_EDMINI_V2;
+
+     /* adress of boot parameters */
+     gd->bd->bi_boot_params = orion5x_sdram_bar(0) + 0x100;
+
+     return 0;
+}
+
+int dram_init(void)
+{
+     int i;
+
+     for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+             gd->bd->bi_dram[i].start = orion5x_sdram_bar(i);
+             gd->bd->bi_dram[i].size = orion5x_sdram_bs(i);
+     }
+     return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+     u16 reg;
+     u16 devadr;
+     char *name = "egiga0";
+
+     if (miiphy_set_current_dev(name))
+             return;
+
+     /* command to read PHY dev address */
+     if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+             printf("Err..%s could not read PHY dev address\n",
+                     __FUNCTION__);
+             return;
+     }
+
+     /*
+      * Enable RGMII delay on Tx and Rx for CPU port
+      * Ref: sec 4.7.2 of chip datasheet
+      */
+     miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+     miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
+     reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+     miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+     miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+     /* reset the phy */
+     miiphy_reset(name, devadr);
+
+     printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
board/Marvell/edminiv2/edminiv2.h new file +0 -0
new file mode 100644
index 0000000..77a108e

board/Marvell/edminiv2/edminiv2.h line 4

Quoted 4 lines
board/Marvell/edminiv2/edminiv2.h new file +4 -0
@@ -0,0 +1,39 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>

Ditto

Quoted 25 lines
board/Marvell/edminiv2/edminiv2.h new file +25 -0
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __EDMINIV2_H
+#define __EDMINIV2_H
+
+#define EDMINIV2_OE_LOW              (~(0))
+#define EDMINIV2_OE_VAL_LOW          (1 << 29)       /*
Quoted 1 line

USB_PWEN low */

Pls remove word LOW here

Quoted 40 lines
board/Marvell/edminiv2/edminiv2.h new file +10 -0
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG              10
+#define MV88E1116_CPRSP_CR3_REG              21
+#define MV88E1116_MAC_CTRL_REG               21
+#define MV88E1116_PGADR_REG          22
+#define MV88E1116_RGMII_TXTM_CTRL    (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL    (1 << 5)
+
+#endif /* __EDMINIV2_H */
cpu/arm926ejs/orion5x/Makefile new file +23 -0
new file mode 100644
index 0000000..4b506a7
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2009 Albert ARIBAUD <[email protected]>
+#
+# Based on original Kirkwood support which is
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software

cpu/arm926ejs/orion5x/Makefile line 33

Quoted 10 lines
cpu/arm926ejs/orion5x/Makefile new file +10 -0
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB  = $(obj)lib$(SOC).a
+
+COBJS-y      = dram.o
+COBJS-y      += cpu.o

Pls put these lines in order

Quoted 198 lines
cpu/arm926ejs/orion5x/Makefile new file +12 -0
+COBJS-y      += mpp.o
+COBJS-y      += timer.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all: $(obj).depend $(LIB)
+
+$(LIB):      $(OBJS)
+     $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#############################################################

############

cpu/arm926ejs/orion5x/Makefile new file +7 -0
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#############################################################

############

cpu/arm926ejs/orion5x/cpu.c new file +51 -0
new file mode 100644
index 0000000..50ca724
@@ -0,0 +1,339 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood support which is
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/cache.h>
+#include <u-boot/md5.h>
+#include <asm/arch/orion5x.h>
+#include <hush.h>
+
+#define BUFLEN       16
+
+void reset_cpu(unsigned long ignored)
+{
+     struct orion5x_cpu_registers *cpureg =
+         (struct orion5x_cpu_registers *)ORION5X_CPU_REG_BASE;
+
+     writel(readl(&cpureg->rstoutn_mask) | (1 << 2),
+             &cpureg->rstoutn_mask);
+     writel(readl(&cpureg->sys_soft_rst) | 1,
+             &cpureg->sys_soft_rst);
+     while (1) ;
+}
+
+/*
+ * Window Size
+ * Used with the Base register to set the address window

size and location.
+ * Must be programmed from LSB to MSB as sequence of ones followed by
+ * sequence of zeros. The number of ones specifies the size of the window in
+ * 64 KByte granularity (e.g., a value of 0x00FF specifies 256 = 16 MByte).
+ * NOTE: A value of 0x0 specifies 64-KByte size.
+ */

cpu/arm926ejs/orion5x/cpu.c new file +17 -0
+unsigned int orion5x_winctrl_calcsize(unsigned int sizeval)
+{
+     int i;
+     unsigned int j = 0;
+     u32 val = sizeval >> 1;
+
+     for (i = 0; val > 0x10000; i++) {
+             j |= (1 << i);
+             val = val >> 1;
+     }
+     return (0x0000ffff & j);
+}
+
+/*
+ * orion5x_config_adr_windows - Configure address Windows
+ *
+ * There are 8 address windows supported by Orion5x Soc to

addess different
+ * devices. Each window can be configured for size, BAR and remap addr
+ * Below configuration is standard for most of the cases
+ *
+ * If remap function not used, remap_lo must be set as base
+ *
+ * Reference Documentation:
+ * Mbus-L to Mbus Bridge Registers Configuration.
+ * (Sec 25.1 and 25.3 of Datasheet)
+ */

cpu/arm926ejs/orion5x/cpu.c new file +7 -0
+int orion5x_config_adr_windows(void)
+{
+     struct orion5x_win_registers *winregs =
+             (struct orion5x_win_registers *)ORION5X_CPU_WIN_BASE;
+
+     /* Window 0: PCIE MEM address space */
+

writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_PCIE_MEM, ORION5X_TARGET_PCIE,
+ ORION5X_ATTR_PCIE_MEM, ORION5X_WIN_ENABLE),
&winregs[0].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +6 -0
+     writel(ORION5X_DEFADR_PCIE_MEM, &winregs[0].base);
+     writel(ORION5X_DEFADR_PCIE_MEM_REMAP_LO, &winregs[0].remap_lo);
+     writel(ORION5X_DEFADR_PCIE_MEM_REMAP_HI, &winregs[0].remap_hi);
+
+     /* Window 1: PCIE IO address space */
+     writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_PCIE_IO,

ORION5X_TARGET_PCIE,
+ ORION5X_ATTR_PCIE_IO, ORION5X_WIN_ENABLE),
&winregs[1].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +6 -0
+     writel(ORION5X_DEFADR_PCIE_IO, &winregs[1].base);
+     writel(ORION5X_DEFADR_PCIE_IO_REMAP_LO, &winregs[1].remap_lo);
+     writel(ORION5X_DEFADR_PCIE_IO_REMAP_HI, &winregs[1].remap_hi);
+
+     /* Window 2: PCI MEM address space */
+     writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_PCI_MEM,

ORION5X_TARGET_PCI,
+ ORION5X_ATTR_PCI_MEM, ORION5X_WIN_ENABLE),
&winregs[2].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +4 -0
+     writel(ORION5X_DEFADR_PCI_MEM, &winregs[2].base);
+
+     /* Window 3: PCI IO address space */
+     writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_PCI_IO,

ORION5X_TARGET_PCI,
+ ORION5X_ATTR_PCI_IO, ORION5X_WIN_ENABLE),
&winregs[3].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +4 -0
+     writel(ORION5X_DEFADR_PCI_IO, &winregs[3].base);
+
+     /* Window 4: DEV_CS0 address space */
+     writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_DEV_CS0,

ORION5X_TARGET_DEVICE,
+ ORION5X_ATTR_DEV_CS0, ORION5X_WIN_ENABLE),
&winregs[4].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +4 -0
+     writel(ORION5X_DEFADR_DEV_CS0, &winregs[4].base);
+
+     /* Window 5: DEV_CS1 address space */
+     writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_DEV_CS1,

ORION5X_TARGET_DEVICE,
+ ORION5X_ATTR_DEV_CS1, ORION5X_WIN_ENABLE),
&winregs[5].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +4 -0
+     writel(ORION5X_DEFADR_DEV_CS1, &winregs[5].base);
+
+     /* Window 6: DEV_CS2 address space */
+     writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_DEV_CS2,

ORION5X_TARGET_DEVICE,
+ ORION5X_ATTR_DEV_CS2, ORION5X_WIN_ENABLE),
&winregs[6].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +4 -0
+     writel(ORION5X_DEFADR_DEV_CS2, &winregs[6].base);
+
+     /* Window 7: BOOT Memory address space */
+     writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_DEFSZ_BOOTROM,

ORION5X_TARGET_DEVICE,
+ ORION5X_ATTR_BOOTROM, ORION5X_WIN_ENABLE),
&winregs[7].ctrl);

cpu/arm926ejs/orion5x/cpu.c new file +20 -0
+     writel(ORION5X_DEFADR_BOOTROM, &winregs[7].base);
+
+     return 0;
+}
+
+/*
+ * orion5x_config_gpio - GPIO configuration
+ */
+void orion5x_config_gpio(u32 gpp_oe_val, u32 gpp_oe)
+{
+     struct orion5x_gpio_registers *gpioreg =
+             (struct orion5x_gpio_registers *)ORION5X_GPIO_BASE;
+
+     /* Init GPIOS to default values as per board requirement */
+     writel(gpp_oe_val, &gpioreg->dout);
+     writel(gpp_oe, &gpioreg->oe);
+}
+
+/*
+ * orion5x_config_mpp - Multi-Purpose Pins Functionality
Quoted 6 lines

configuration
+ *
+ * Each MPP can be configured to different functionality through
+ * MPP control register, ref (sec 6.1 of Orion5x h/w specification)
+ *
+ * There are maximum 64 Multi-Pourpose Pins on Orion5x

Correct this -64

Quoted 12 lines

+ * Each MPP functionality can be configuration by a 4bit value
+ * of MPP control reg, the value and associated functionality depends
+ * upon used SoC varient
+ */

cpu/arm926ejs/orion5x/cpu.c new file +8 -0
+int orion5x_config_mpp(u32 mpp0_7, u32 mpp8_15, u32 mpp16_23)
+{
+     u32 *mppreg = (u32 *) ORION5X_MPP_BASE;
+
+     /* program mpp registers */
+     writel(mpp0_7, &mppreg[0]);
+     writel(mpp8_15, &mppreg[1]);
+     writel(mpp16_23, &mppreg[2]);

cpu/arm926ejs/orion5x/cpu.c line 176

Quoted 10 lines
cpu/arm926ejs/orion5x/cpu.c new file +10 -0
+     return 0;
+}
+
+/* Orion5x identification is done through PCIE space.
+ * As long as there is no Orion5x support for PCIE,
+ * We'll define the ID and revision PCIE registers
+ * here.
+ */
+#define PCIE_DEV_ID_OFF         (ORION5X_REG_PCIE_BASE + 0x0000)
+#define PCIE_DEV_REV_OFF        (ORION5X_REG_PCIE_BASE + 0x0008)

Pls move the defination to header file

Quoted 53 lines
cpu/arm926ejs/orion5x/cpu.c new file +53 -0
+u32 orion5x_device_id(void)
+{
+     return readl(PCIE_DEV_ID_OFF) >> 16;
+}
+
+u32 orion5x_device_rev(void)
+{
+     return readl(PCIE_DEV_REV_OFF) & 0xff;
+}
+
+#if defined(CONFIG_DISPLAY_CPUINFO)
+
+int print_cpuinfo(void)
+{
+     char dev_str[] = "0x0000";
+     char *dev_name = dev_str;
+     char rev_str[] = "0x00";
+     char *rev_name = rev_str;
+
+     u32 dev = orion5x_device_id();
+     u32 rev = orion5x_device_rev();
+
+     if (dev == MV88F5181_DEV_ID) {
+             dev_name = "MV88F5181";
+             if (rev == MV88F5181_REV_B1) {
+                     rev_name = "B1";
+             } else if (rev == MV88F5181L_REV_A1) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A1";
+             } else if (rev == MV88F5181L_REV_A0) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5182_DEV_ID) {
+             dev_name = "MV88F5182";
+             if (rev == MV88F5182_REV_A2) {
+                     rev_name = "A2";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5281_DEV_ID) {
+             dev_name = "MV88F5281";
+             if (rev == MV88F5281_REV_D2) {
+                     rev_name = "D2";
+             } else if (rev == MV88F5281_REV_D1) {
+                     rev_name = "D1";
+             } else if (rev == MV88F5281_REV_D0) {
+                     rev_name = "D0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }

cpu/arm926ejs/orion5x/cpu.c line 239

Quoted 10 lines
cpu/arm926ejs/orion5x/cpu.c new file +10 -0
+     } else if (dev == MV88F6183_DEV_ID) {
+             dev_name = "MV88F6183";
+             if (rev == MV88F6183_REV_B0) {
+                     rev_name = "B0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else {
+             sprintf(dev_str,"0x%04x", rev);
+             sprintf(rev_str,"0x%02x", rev);

This is common line, pls take out of if-else

Quoted 93 lines
cpu/arm926ejs/orion5x/cpu.c new file +37 -0
+     }
+
+     printf("SoC:   Orion5x %s-%s\n", dev_name, rev_name);
+
+     return 0;
+}
+#endif /* CONFIG_DISPLAY_CPUINFO */
+
+#ifdef CONFIG_ARCH_CPU_INIT
+int arch_cpu_init(void)
+{
+     struct orion5x_cpu_registers *cpureg =
+             (struct orion5x_cpu_registers *)ORION5X_CPU_REG_BASE;
+
+     /* Linux expects` the internal registers to be at 0xf1000000 */
+     writel(ORION5X_REGS_PHY_BASE, ORION5X_OFFSET_REG);
+
+     /* Enable and invalidate L2 cache in write through mode */
+     writel(readl(&cpureg->l2_cfg) | 0x18, &cpureg->l2_cfg);
+     invalidate_l2_cache();
+
+     orion5x_config_adr_windows();
+
+#ifdef CONFIG_ORION5X_RGMII_PAD_1V8
+     /*
+      * Configures the I/O voltage of the pads connected to Egigabit
+      * Ethernet interface to 1.8V
+      * By defult it is set to 3.3V
+      */
+     reg = readl(ORION5X_REG_MPP_OUT_DRV_REG);
+     reg |= (1 << 7);
+     writel(reg, ORION5X_REG_MPP_OUT_DRV_REG);
+#endif
+#ifdef CONFIG_ORION5X_EGIGA_INIT
+     /*
+      * Set egiga port0/1 in normal functional mode
+      * This is required becasue on Orion5x by default ports

are in reset mode
+ * OS egiga driver may not have provision to set them
in normal mode
+ * and if u-boot is build without network support,
network may fail at OS level

cpu/arm926ejs/orion5x/cpu.c new file +51 -0
+      */
+     reg = readl(ORION5XGBE_PORT_SERIAL_CONTROL1_REG(0));
+     reg &= ~(1 << 4);       /* Clear PortReset Bit */
+     writel(reg, (ORION5XGBE_PORT_SERIAL_CONTROL1_REG(0)));
+     reg = readl(ORION5XGBE_PORT_SERIAL_CONTROL1_REG(1));
+     reg &= ~(1 << 4);       /* Clear PortReset Bit */
+     writel(reg, (ORION5XGBE_PORT_SERIAL_CONTROL1_REG(1)));
+#endif
+#ifdef CONFIG_ORION5X_PCIE_INIT
+     /*
+      * Enable PCI Express Port0
+      */
+     reg = readl(&cpureg->ctrl_stat);
+     reg |= (1 << 0);        /* Set PEX0En Bit */
+     writel(reg, &cpureg->ctrl_stat);
+#endif
+     return 0;
+}
+#endif /* CONFIG_ARCH_CPU_INIT */
+
+/*
+ * SOC specific misc init
+ */
+#if defined(CONFIG_ARCH_MISC_INIT)
+int arch_misc_init(void)
+{
+     volatile u32 temp;
+
+     /*CPU streaming & write allocate */
+     temp = readfr_extra_feature_reg();
+     temp &= ~(1 << 28);     /* disable wr alloc */
+     writefr_extra_feature_reg(temp);
+
+     temp = readfr_extra_feature_reg();
+     temp &= ~(1 << 29);     /* streaming disabled */
+     writefr_extra_feature_reg(temp);
+
+     /* L2Cache settings */
+     temp = readfr_extra_feature_reg();
+     /* Disable L2C pre fetch - Set bit 24 */
+     temp |= (1 << 24);
+     /* enable L2C - Set bit 22 */
+     temp |= (1 << 22);
+     writefr_extra_feature_reg(temp);
+
+     icache_enable();
+     /* Change reset vector to address 0x0 */
+     temp = get_cr();
+     set_cr(temp & ~CR_V);
+
+     return 0;

cpu/arm926ejs/orion5x/cpu.c line 339

Quoted 10 lines
cpu/arm926ejs/orion5x/cpu.c new file +10 -0
+}
+#endif /* CONFIG_ARCH_MISC_INIT */
+
+#ifdef CONFIG_ORION5X_EGIGA
+int cpu_eth_init(bd_t *bis)
+{
+     orion5x_egiga_initialize(bis);
+     return 0;
+}
+#endif

Pls do not add this by default, make it a part of egiga driver patch

Quoted 551 lines
cpu/arm926ejs/orion5x/dram.c new file +31 -0
new file mode 100644
index 0000000..69aec26
@@ -0,0 +1,61 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood support which is
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <config.h>
+#include <asm/arch/orion5x.h>
+
+#define ORION5X_REG_CPUCS_WIN_BAR(x)

(ORION5X_REGISTER(0x1500) + (x * 0x08))
+#define ORION5X_REG_CPUCS_WIN_SZ(x)
(ORION5X_REGISTER(0x1504) + (x * 0x08))

cpu/arm926ejs/orion5x/dram.c new file +29 -0
+/*
+ * orion5x_sdram_bar - reads SDRAM Base Address Register
+ */
+u32 orion5x_sdram_bar(enum memory_bank bank)
+{
+     u32 result = 0;
+     u32 enable = 0x01 & readl(ORION5X_REG_CPUCS_WIN_SZ(bank));
+
+     if ((!enable) || (bank > BANK3))
+             return 0;
+
+     result = readl(ORION5X_REG_CPUCS_WIN_BAR(bank));
+     return result;
+}
+
+/*
+ * orion5x_sdram_bs - reads SDRAM Bank size
+ */
+u32 orion5x_sdram_bs(enum memory_bank bank)
+{
+     u32 result = 0;
+     u32 enable = 0x01 & readl(ORION5X_REG_CPUCS_WIN_SZ(bank));
+
+     if ((!enable) || (bank > BANK3))
+             return 0;
+     result = 0xff000000 & readl(ORION5X_REG_CPUCS_WIN_SZ(bank));
+     result += 0x01000000;
+     return result;
+}
cpu/arm926ejs/orion5x/mpp.c new file +69 -0
new file mode 100644
index 0000000..1b1e7fa
@@ -0,0 +1,88 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood support
+ *
+ * arch/arm/mach-orion5x/mpp.c
+ *
+ * MPP functions for Marvell Kirorion5xood SoCs
+ * Referenced from Linux kernel source
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <common.h>
+#include <asm/arch/orion5x.h>
+#include <asm/arch/mpp.h>
+
+static u32 orion5x_variant(void)
+{
+        switch (orion5x_device_id()) {
+             case MV88F5181_DEV_ID:
+                     return 0;
+             case MV88F5182_DEV_ID:
+                     return MPP_F5182_MASK;
+             case MV88F5281_DEV_ID:
+                     return MPP_F5281_MASK;
+             case MV88F6183_DEV_ID:
+                     return 0;
+             default:
+                     debug("MPP setup: unknown Orion5x variant\n");
+                     return 0;
+     }
+}
+
+#define MPP_CTRL(i)  (ORION5X_MPP_BASE + (i* 4))
+#define MPP_NR_REGS  (1 + MPP_MAX/8)
+
+void orion5x_mpp_conf(u32 *mpp_list)
+{
+     u32 mpp_ctrl[MPP_NR_REGS];
+     unsigned int variant_mask;
+     int i;
+
+     variant_mask = orion5x_variant();
+     if (!variant_mask)
+             return;
+
+     debug( "initial MPP regs:");
+     for (i = 0; i < MPP_NR_REGS; i++) {
+             mpp_ctrl[i] = readl(MPP_CTRL(i));
+             debug(" %08x", mpp_ctrl[i]);
+     }
+     debug("\n");
+
+
+     while (*mpp_list) {
+             unsigned int num = MPP_NUM(*mpp_list);
+             unsigned int sel = MPP_SEL(*mpp_list);
+             int shift;
+
+             if (num > MPP_MAX) {
+                     debug("orion5x_mpp_conf: invalid MPP "
+                                     "number (%u)\n", num);
+                     continue;
+             }
+             if (!(*mpp_list & variant_mask)) {
+                     debug("orion5x_mpp_conf: requested

MPP%u config "

cpu/arm926ejs/orion5x/mpp.c new file +19 -0
+                             "unavailable on this hardware\n", num);
+                     continue;
+             }
+
+             shift = (num & 7) << 2;
+             mpp_ctrl[num / 8] &= ~(0xf << shift);
+             mpp_ctrl[num / 8] |= sel << shift;
+
+             mpp_list++;
+     }
+
+     debug("  final MPP regs:");
+     for (i = 0; i < MPP_NR_REGS; i++) {
+             writel(mpp_ctrl[i], MPP_CTRL(i));
+             debug(" %08x", mpp_ctrl[i]);
+     }
+     debug("\n");
+
+}
cpu/arm926ejs/orion5x/timer.c new file +47 -0
new file mode 100644
index 0000000..80fee75
@@ -0,0 +1,171 @@
+/*
+  * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood support which is
+ * Copyright (C) Marvell International Ltd. and its affiliates
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/orion5x.h>
+
+#define UBOOT_CNTR   0       /* counter to use for uboot timer */
+
+/* Timer reload and current value registers */
+struct orion5x_tmr_val {
+     u32 reload;     /* Timer reload reg */
+     u32 val;        /* Timer value reg */
+};
+
+/* Timer registers */
+struct orion5x_tmr_registers {
+     u32 ctrl;       /* Timer control reg */
+     u32 pad[3];
+     struct orion5x_tmr_val tmr[2];
+     u32 wdt_reload;
+     u32 wdt_val;
+};
+
+struct orion5x_tmr_registers *orion5x_tmr_regs = (struct

orion5x_tmr_registers *)ORION5X_TIMER_BASE;

cpu/arm926ejs/orion5x/timer.c new file +6 -0
+
+/*
+ * ARM Timers Registers Map
+ */
+#define CNTMR_CTRL_REG                       &orion5x_tmr_regs->ctrl
+#define CNTMR_RELOAD_REG(tmrnum)

&orion5x_tmr_regs->tmr[tmrnum].reload
+#define CNTMR_VAL_REG(tmrnum)
&orion5x_tmr_regs->tmr[tmrnum].val

cpu/arm926ejs/orion5x/timer.c new file +8 -0
+
+/*
+ * ARM Timers Control Register
+ * CPU_TIMERS_CTRL_REG (CTCR)
+ */
+#define CTCR_ARM_TIMER_EN_OFFS(cntr) (cntr * 2)
+#define CTCR_ARM_TIMER_EN_MASK(cntr) (1 << CTCR_ARM_TIMER_EN_OFFS)
+#define CTCR_ARM_TIMER_EN(cntr)              (1 <<

CTCR_ARM_TIMER_EN_OFFS(cntr))
+#define CTCR_ARM_TIMER_DIS(cntr) (0 <<
CTCR_ARM_TIMER_EN_OFFS(cntr))

cpu/arm926ejs/orion5x/timer.c new file +4 -0
+
+#define CTCR_ARM_TIMER_AUTO_OFFS(cntr)       ((cntr * 2) + 1)
+#define CTCR_ARM_TIMER_AUTO_MASK(cntr)       (1 << 1)
+#define CTCR_ARM_TIMER_AUTO_EN(cntr) (1 <<

CTCR_ARM_TIMER_AUTO_OFFS(cntr))
+#define CTCR_ARM_TIMER_AUTO_DIS(cntr) (0 <<
CTCR_ARM_TIMER_AUTO_OFFS(cntr))

cpu/arm926ejs/orion5x/timer.c new file +18 -0
+
+/*
+ * ARM Timer\Watchdog Reload Register
+ * CNTMR_RELOAD_REG (TRR)
+ */
+#define TRG_ARM_TIMER_REL_OFFS               0
+#define TRG_ARM_TIMER_REL_MASK               0xffffffff
+
+/*
+ * ARM Timer\Watchdog Register
+ * CNTMR_VAL_REG (TVRG)
+ */
+#define TVR_ARM_TIMER_OFFS           0
+#define TVR_ARM_TIMER_MASK           0xffffffff
+#define TVR_ARM_TIMER_MAX            0xffffffff
+#define TIMER_LOAD_VAL                       0xffffffff
+
+#define READ_TIMER

(readl(CNTMR_VAL_REG(UBOOT_CNTR)) / \

cpu/arm926ejs/orion5x/timer.c new file +23 -0
+                                      (CONFIG_SYS_TCLK / 1000))
+
+static ulong timestamp;
+static ulong lastdec;
+
+void reset_timer_masked(void)
+{
+     /* reset time */
+     lastdec = READ_TIMER;
+     timestamp = 0;
+}
+
+ulong get_timer_masked(void)
+{
+     ulong now = READ_TIMER;
+
+     if (lastdec >= now) {
+             /* normal mode */
+             timestamp += lastdec - now;
+     } else {
+             /* we have an overflow ... */
+             timestamp += lastdec +
+                     (TIMER_LOAD_VAL / (CONFIG_SYS_TCLK /

1000)) - now;

cpu/arm926ejs/orion5x/timer.c new file +62 -0
+     }
+     lastdec = now;
+
+     return timestamp;
+}
+
+void reset_timer(void)
+{
+     reset_timer_masked();
+}
+
+ulong get_timer(ulong base)
+{
+     return get_timer_masked() - base;
+}
+
+void set_timer(ulong t)
+{
+     timestamp = t;
+}
+
+void udelay(unsigned long usec)
+{
+     uint current;
+     ulong delayticks;
+
+     current = readl(CNTMR_VAL_REG(UBOOT_CNTR));
+     delayticks = (usec * (CONFIG_SYS_TCLK / 1000000));
+
+     if (current < delayticks) {
+             delayticks -= current;
+             while (readl(CNTMR_VAL_REG(UBOOT_CNTR)) < current) ;
+             while ((TIMER_LOAD_VAL - delayticks) <
+                     readl(CNTMR_VAL_REG(UBOOT_CNTR))) ;
+     } else {
+             while (readl(CNTMR_VAL_REG(UBOOT_CNTR)) >
+                     (current - delayticks)) ;
+     }
+}
+
+/*
+ * init the counter
+ */
+int timer_init(void)
+{
+     unsigned int cntmrctrl;
+
+     /* load value into timer */
+     writel(TIMER_LOAD_VAL, CNTMR_RELOAD_REG(UBOOT_CNTR));
+     writel(TIMER_LOAD_VAL, CNTMR_VAL_REG(UBOOT_CNTR));
+
+     /* enable timer in auto reload mode */
+     cntmrctrl = readl(CNTMR_CTRL_REG);
+     cntmrctrl |= CTCR_ARM_TIMER_EN(UBOOT_CNTR);
+     cntmrctrl |= CTCR_ARM_TIMER_AUTO_EN(UBOOT_CNTR);
+     writel(cntmrctrl, CNTMR_CTRL_REG);
+
+     /* init the timestamp and lastdec value */
+     reset_timer_masked();
+
+     return 0;
+}
drivers/serial/serial.c +3 -0
index dd5f332..18686a2 100644
@@ -30,6 +30,9 @@
 #ifdef CONFIG_KIRKWOOD
 #include <asm/arch/kirkwood.h>
 #endif
+#ifdef CONFIG_ORION5X
+#include <asm/arch/orion5x.h>
+#endif
 
 #if defined (CONFIG_SERIAL_MULTI)
 #include <serial.h>
include/asm-arm/arch-orion5x/88f5182.h new file +40 -0
new file mode 100644
index 0000000..1dfdb24
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood 88F6182 support which is
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * Header file for Feroceon CPU core 88F5182 SOC.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_88F5182_H
+#define _CONFIG_88F5182_H
+
+/* SOC specific definations */
+#define F88F5182_REGS_PHYS_BASE              0xf1000000
+#define ORION5X_REGS_PHY_BASE                F88F5182_REGS_PHYS_BASE
+
+/* TCLK Core Clock defination */
+#define CONFIG_SYS_TCLK                      166000000 /* 166MHz */
+
+#endif /* _CONFIG_88F5182_H */
include/asm-arm/arch-orion5x/cpu.h new file +35 -0
new file mode 100644
index 0000000..7078d2e
@@ -0,0 +1,213 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirorion5x_ood support which is
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _ORION5X_CPU_H
+#define _ORION5X_CPU_H
+
+#include <asm/system.h>
+
+#ifndef __ASSEMBLY__
+
+#define ORION5X_CPU_WIN_CTRL_DATA(size, target, attr, en)

(en | (target << 4) \
+ | (attr << 8) |
(orion5x_winctrl_calcsize(size) << 16))

include/asm-arm/arch-orion5x/cpu.h new file +3 -0
+
+#define ORION5XGBE_PORT_SERIAL_CONTROL1_REG(_x)      \
+             ((_x ? ORION5X_EGIGA0_BASE :

ORION5X_EGIGA1_BASE) + 0x44c)

include/asm-arm/arch-orion5x/cpu.h new file +2 -0
+
+#define ORION5X_REG_DEVICE_ID

(ORION5X_MPP_BASE + 0x34)
+#define ORION5X_REG_SYSRST_CNT
(ORION5X_MPP_BASE + 0x50)

include/asm-arm/arch-orion5x/cpu.h new file +2 -0
+#define SYSRST_CNT_1SEC_VAL          (25*1000000)
+#define ORION5X_REG_MPP_OUT_DRV_REG

(ORION5X_MPP_BASE + 0xE0)

include/asm-arm/arch-orion5x/cpu.h new file +81 -0
+
+enum memory_bank {
+     BANK0,
+     BANK1,
+     BANK2,
+     BANK3
+};
+
+enum orion5x_cpu_winen {
+     ORION5X_WIN_DISABLE,
+     ORION5X_WIN_ENABLE
+};
+
+enum orion5x_cpu_target {
+     ORION5X_TARGET_DRAM = 0,
+     ORION5X_TARGET_DEVICE = 1,
+     ORION5X_TARGET_PCI = 3,
+     ORION5X_TARGET_PCIE = 4,
+     ORION5X_TARGET_SASRAM = 9
+};
+
+enum orion5x_cpu_attrib {
+     ORION5X_ATTR_DRAM_CS0 = 0x0e,
+     ORION5X_ATTR_DRAM_CS1 = 0x0d,
+     ORION5X_ATTR_DRAM_CS2 = 0x0b,
+     ORION5X_ATTR_DRAM_CS3 = 0x07,
+     ORION5X_ATTR_PCI_MEM = 0x59,
+     ORION5X_ATTR_PCI_IO = 0x51,
+     ORION5X_ATTR_PCIE_MEM = 0x59,
+     ORION5X_ATTR_PCIE_IO = 0x51,
+     ORION5X_ATTR_SASRAM = 0x00,
+     ORION5X_ATTR_DEV_CS0 = 0x1e,
+     ORION5X_ATTR_DEV_CS1 = 0x1d,
+     ORION5X_ATTR_DEV_CS2 = 0x1b,
+     ORION5X_ATTR_BOOTROM = 0x0f
+};
+
+/*
+ * Default Device Address MAP BAR values
+ */
+#define ORION5X_DEFADR_PCIE_MEM      0x90000000
+#define ORION5X_DEFADR_PCIE_MEM_REMAP_LO     0x90000000
+#define ORION5X_DEFADR_PCIE_MEM_REMAP_HI     0
+#define ORION5X_DEFSZ_PCIE_MEM       (128*1024*1024)
+
+#define ORION5X_DEFADR_PCIE_IO       0xf0000000
+#define ORION5X_DEFADR_PCIE_IO_REMAP_LO      0x90000000
+#define ORION5X_DEFADR_PCIE_IO_REMAP_HI      0
+#define ORION5X_DEFSZ_PCIE_IO        (64*1024)
+
+#define ORION5X_DEFADR_PCI_MEM       0x98000000
+#define ORION5X_DEFSZ_PCI_MEM        (128*1024*1024)
+
+#define ORION5X_DEFADR_PCI_IO        0xf0100000
+#define ORION5X_DEFSZ_PCI_IO (64*1024)
+
+#define ORION5X_DEFADR_DEV_CS0       0xfa000000
+#define ORION5X_DEFSZ_DEV_CS0        (2*1024*1024)
+
+#define ORION5X_DEFADR_DEV_CS1       0xf8000000
+#define ORION5X_DEFSZ_DEV_CS1        (32*1024*1024)
+
+#define ORION5X_DEFADR_DEV_CS2       0xfa800000
+#define ORION5X_DEFSZ_DEV_CS2        (1*1024*1024)
+
+#define ORION5X_DEFADR_BOOTROM       0xFFF80000
+#define ORION5X_DEFSZ_BOOTROM        (512*1024)
+
+/* Constants for known devices and revisions
+ *
+ */
+
+/* Orion-1 (88F5181) and Orion-VoIP (88F5181L) */
+#define MV88F5181_DEV_ID        0x5181
+#define MV88F5181_REV_B1        3
+#define MV88F5181L_REV_A0       8
+#define MV88F5181L_REV_A1       9
+/* Orion-NAS (88F5182) */
+#define MV88F5182_DEV_ID        0x5182
+#define MV88F5182_REV_A2        2
+/* Orion-2 (88F5281) */

include/asm-arm/arch-orion5x/cpu.h line 135

Quoted 10 lines
include/asm-arm/arch-orion5x/cpu.h new file +10 -0
+#define MV88F5281_DEV_ID        0x5281
+#define MV88F5281_REV_D0        4
+#define MV88F5281_REV_D1        5
+#define MV88F5281_REV_D2        6
+/* Orion-1-90 (88F6183) */
+#define MV88F6183_DEV_ID        0x6183
+#define MV88F6183_REV_B0        3
+
+/*
+ * read feroceon/sheeva core extra feature register

Pls remove name sheeva

include/asm-arm/arch-orion5x/cpu.h line 147

Quoted 12 lines

+ * using co-proc instruction
+ */

include/asm-arm/arch-orion5x/cpu.h new file +10 -0
+static inline unsigned int readfr_extra_feature_reg(void)
+{
+     unsigned int val;
+     asm volatile ("mrc p15, 1, %0, c15, c1, 0 @ readfr exfr":"=r"
+                     (val)::"cc");
+     return val;
+}
+
+/*
+ * write feroceon/sheeva core extra feature register

Same

include/asm-arm/arch-orion5x/cpu.h line 159

Quoted 12 lines

+ * using co-proc instruction
+ */

include/asm-arm/arch-orion5x/cpu.h new file +10 -0
+static inline void writefr_extra_feature_reg(unsigned int val)
+{
+     asm volatile ("mcr p15, 1, %0, c15, c1, 0 @ writefr exfr"::"r"
+                     (val):"cc");
+     isb();
+}
+
+/*
+ * MBus-L to Mbus Bridge Registers
+ * Ref: Datasheet sec:A.3

Are those references correct?

include/asm-arm/arch-orion5x/cpu.h line 170

Quoted 11 lines

+ */

include/asm-arm/arch-orion5x/cpu.h new file +10 -0
+struct orion5x_win_registers {
+     u32 ctrl;
+     u32 base;
+     u32 remap_lo;
+     u32 remap_hi;
+};
+
+/*
+ * CPU control and status Registers
+ * Ref: Datasheet sec:A.3.2

Are those references correct?

Quoted 7 lines

+ */

include/asm-arm/arch-orion5x/cpu.h new file +6 -0
+struct orion5x_cpu_registers {
+     u32 config;     /*0x20100 */
+     u32 ctrl_stat;  /*0x20104 */
+     u32 rstoutn_mask; /* 0x20108 */
+     u32 sys_soft_rst; /* 0x2010C */
+     u32 ahb_mbus_cause_irq; /* 0x20110 */

include/asm-arm/arch-orion5x/cpu.h line 187

Quoted 10 lines
include/asm-arm/arch-orion5x/cpu.h new file +10 -0
+     u32 ahb_mbus_mask_irq; /* 0x20114 */
+     u32 pad1[2];
+     u32 ftdll_config; /* 0x20120 */
+     u32 pad2;
+     u32 l2_cfg;     /* 0x20128 */
+};
+
+/*
+ * GPIO Registers
+ * Ref: Datasheet sec:A.19

Are those references correct?

Quoted 61 lines

+ */

include/asm-arm/arch-orion5x/cpu.h new file +21 -0
+struct orion5x_gpio_registers {
+     u32 dout;
+     u32 oe;
+     u32 blink_en;
+     u32 din_pol;
+     u32 din;
+     u32 irq_cause;
+     u32 irq_mask;
+     u32 irq_level;
+};
+
+/*
+ * functions
+ */
+void reset_cpu(unsigned long ignored);
+u32 orion5x_device_id(void);
+u32 orion5x_device_rev(void);
+unsigned int orion5x_sdram_bar(enum memory_bank bank);
+unsigned int orion5x_sdram_bs(enum memory_bank bank);
+int orion5x_config_adr_windows(void);
+void orion5x_config_gpio(unsigned int gpp_oe_val, unsigned

int gpp_oe);
+int orion5x_config_mpp(unsigned int mpp0_7, unsigned int mpp8_15, unsigned int mpp16_23);

include/asm-arm/arch-orion5x/cpu.h new file +3 -0
+unsigned int orion5x_winctrl_calcsize(unsigned int sizeval);
+#endif /* __ASSEMBLY__ */
+#endif /* _ORION5X_CPU_H */
include/asm-arm/arch-orion5x/gpio.h new file +12 -0
new file mode 100644
index 0000000..40fe2e0
@@ -0,0 +1,53 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on arch/asm-arm/mach-kirkwood/include/mach/gpio.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * Based on (mostly copied from) plat-orion based Linux 2.6

kernel driver.
+ * Removed kernel level irq handling. Took some macros from kernel to
+ * allow build.
+ *
+ * Dieter Kiermaier dk-arm-linux at gmx.de
+ */

include/asm-arm/arch-orion5x/gpio.h new file +7 -0
+
+#ifndef __ORION5X_GPIO_H
+#define __ORION5X_GPIO_H
+
+/* got from kernel include/linux/bitops.h */
+#define BITS_PER_BYTE 8
+#define BITS_TO_LONGS(nr)    DIV_ROUND_UP(nr, BITS_PER_BYTE

* sizeof(long))

include/asm-arm/arch-orion5x/gpio.h line 26

Quoted 2 lines
include/asm-arm/arch-orion5x/gpio.h new file +2 -0
+
+#define GPIO_MAX             50

Is this correct defination for Orion?

Quoted 17 lines
include/asm-arm/arch-orion5x/gpio.h new file +2 -0
+#define GPIO_OFF(pin)                (((pin) >> 5) ? 0x0040 : 0x0000)
+#define GPIO_OUT(pin)                (ORION5X_GPIO0_BASE +

GPIO_OFF(pin) + 0x00)
+#define GPIO_IO_CONF(pin) (ORION5X_GPIO0_BASE +
GPIO_OFF(pin) + 0x04)
+#define GPIO_BLINK_EN(pin) (ORION5X_GPIO0_BASE +
GPIO_OFF(pin) + 0x08)
+#define GPIO_IN_POL(pin) (ORION5X_GPIO0_BASE +
GPIO_OFF(pin) + 0x0c)
+#define GPIO_DATA_IN(pin) (ORION5X_GPIO0_BASE +
GPIO_OFF(pin) + 0x10)
+#define GPIO_EDGE_CAUSE(pin) (ORION5X_GPIO0_BASE + GPIO_OFF(pin) + 0x14)
+#define GPIO_EDGE_MASK(pin) (ORION5X_GPIO0_BASE + GPIO_OFF(pin) + 0x18)
+#define GPIO_LEVEL_MASK(pin) (ORION5X_GPIO0_BASE + GPIO_OFF(pin) + 0x1c)

include/asm-arm/arch-orion5x/gpio.h line 38

Quoted 3 lines
include/asm-arm/arch-orion5x/gpio.h new file +3 -0
+
+/*
+ * Kirorion5xood-specific GPIO API

Copy paste error

Quoted 246 lines

+ */

include/asm-arm/arch-orion5x/gpio.h new file +14 -0
+
+void orion5x_gpio_set_valid(unsigned pin, int mode);
+int orion5x_gpio_is_valid(unsigned pin, int mode);
+int orion5x_gpio_direction_input(unsigned pin);
+int orion5x_gpio_direction_output(unsigned pin, int value);
+int orion5x_gpio_get_value(unsigned pin);
+void orion5x_gpio_set_value(unsigned pin, int value);
+void orion5x_gpio_set_blink(unsigned pin, int blink);
+void orion5x_gpio_set_unused(unsigned pin);
+
+#define GPIO_INPUT_OK                (1 << 0)
+#define GPIO_OUTPUT_OK               (1 << 1)
+
+#endif
include/asm-arm/arch-orion5x/mpp.h new file +28 -0
new file mode 100644
index 0000000..a03eb8e
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood support which is
+ * Copyright 2009: Marvell Technology Group Ltd.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ORION5X_MPP_H
+#define __ORION5X_MPP_H
+
+#define MPP(_num, _sel, _in, _out, _F5182, _F5281) ( \
+     /* MPP number */                ((_num) & 0xff) | \
+     /* MPP select value */          (((_sel) & 0xf) << 8) | \
+     /* may be input signal */       ((!!(_in)) << 12) | \
+     /* may be output signal */      ((!!(_out)) << 13) | \
+     /* available on F5182 */        ((!!(_F5182)) << 14) | \
+     /* available on F5281 */        ((!!(_F5182)) << 15))
+
+#define MPP_NUM(x)   ((x) & 0xff)
+#define MPP_SEL(x)   (((x) >> 8) & 0xf)
+
+                                     /*   num sel  i  o  5182 5281 */
+
+#define MPP_INPUT_MASK                       MPP(  0, 0x0,

1, 0, 0, 0 )
+#define MPP_OUTPUT_MASK MPP( 0, 0x0,
0, 1, 0, 0 )

include/asm-arm/arch-orion5x/mpp.h new file +2 -0
+
+#define MPP_F5182_MASK                       MPP(  0, 0x0,

0, 0, 1, 0 )
+#define MPP_F5281_MASK MPP( 0, 0x0,
0, 0, 0, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +3 -0
+
+#define MPP0_PEX_RST_OUTn            MPP(  0, 0x0, 0, 1, 1,   1    )
+#define MPP0_PCI_REQ2n                       MPP(  0, 0x2,

1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +4 -0
+#define MPP0_GPIO                    MPP(  0, 0x3, 1, 1, 1,   1    )
+
+#define MPP1_GPIO                    MPP(  1, 0x0, 1, 1, 1,   1    )
+#define MPP1_PCI_GNT2n                       MPP(  1, 0x2,

0, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +3 -0
+
+#define MPP2_GPIO                    MPP(  2, 0x0, 1, 1, 1,   1    )
+#define MPP2_PCI_REQ3n                       MPP(  2, 0x2,

1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +4 -0
+#define MPP2_PMEn                    MPP(  2, 0x3, 0, 1, 1,   1    )
+
+#define MPP3_GPIO                    MPP(  3, 0x0, 1, 1, 1,   1    )
+#define MPP3_PCI_GNT3nO                      MPP(  3, 0x2,

0, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +3 -0
+
+#define MPP4_GPIO                    MPP(  4, 0x0, 1, 1, 1,   1    )
+#define MPP4_PCI_REQ4n                       MPP(  4, 0x2,

1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +5 -0
+#define MPP4_BOOT_NAND_FLASH_REn     MPP(  4, 0x4, 0, 0, 1,   1    )
+#define MPP4_SATA0_PRESENTn          MPP(  4, 0x5, 0, 1, 1,   0    )
+
+#define MPP5_GPIO                    MPP(  5, 0x0, 1, 1, 1,   1    )
+#define MPP5_PCI_GNT4n                       MPP(  5, 0x2,

0, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +5 -0
+#define MPP5_BOOT_NAND_FLASH_WEn     MPP(  5, 0x4, 0, 0, 1,   1    )
+#define MPP5_SATA1_PRESENTn          MPP(  5, 0x5, 0, 1, 1,   0    )
+
+#define MPP6_GPIO                    MPP(  6, 0x0, 1, 1, 1,   1    )
+#define MPP6_PCI_REQ5n                       MPP(  6, 0x2,

1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +2 -0
+#define MPP6_NAND_FLASH_RE0n         MPP(  6, 0x4, 0, 0, 1,   1    )
+#define MPP6_SATA0_ACTn                      MPP(  6, 0x5,

0, 1, 1, 0 )

include/asm-arm/arch-orion5x/mpp.h new file +3 -0
+
+#define MPP7_GPIO                    MPP(  7, 0x0, 1, 1, 1,   1    )
+#define MPP7_PCI_GNT5n                       MPP(  7, 0x2,

0, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +2 -0
+#define MPP7_NAND_FLASH_WE0n         MPP(  7, 0x4, 0, 0, 1,   1    )
+#define MPP7_SATA1_ACTn                      MPP(  7, 0x5,

0, 1, 1, 0 )

include/asm-arm/arch-orion5x/mpp.h new file +6 -0
+
+#define MPP8_GPIO                    MPP(  8, 0x0, 1, 1, 1,   1    )
+#define MPP8_GE_COL                  MPP(  8, 0x1, 1, 0, 1,   1    )
+
+#define MPP9_GPIO                    MPP(  9, 0x0, 1, 1, 1,   1    )
+#define MPP9_GE_RXERR                        MPP(  9, 0x1,

1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +6 -0
+
+#define MPP10_GPIO                   MPP( 10, 0x0, 1, 1, 1,   1    )
+#define MPP10_GE_CRS                 MPP( 10, 0x1, 1, 0, 1,   1    )
+
+#define MPP11_GPIO                   MPP( 11, 0x0, 1, 1, 1,   1    )
+#define MPP11_GE_TXERR                       MPP( 11, 0x1,

0, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +3 -0
+
+#define MPP12_GPIO                   MPP( 12, 0x0, 1, 1, 1,   1    )
+#define MPP12_GE_TXD4                        MPP( 12, 0x1,

0, 1, 1, 1 )
+#define MPP12_NAND_FLASH_RE1n MPP( 12, 0x4,
1, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +4 -0
+#define MPP12_SATA0_PRESENTn         MPP( 12, 0x5, 0, 1, 1,   0    )
+
+#define MPP13_GPIO                   MPP( 13, 0x0, 1, 1, 1,   1    )
+#define MPP13_GE_TXD5                        MPP( 13, 0x1,

0, 1, 1, 1 )
+#define MPP13_NAND_FLASH_WE1n MPP( 13, 0x4,
0, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +4 -0
+#define MPP13_SATA1_PRESENTn         MPP( 13, 0x5, 0, 1, 1,   0    )
+
+#define MPP14_GPIO                   MPP( 14, 0x0, 1, 1, 1,   1    )
+#define MPP14_GE_TXD6                        MPP( 14, 0x1,

0, 1, 1, 1 )
+#define MPP14_NAND_FLASH_RE2n MPP( 14, 0x4,
1, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +4 -0
+#define MPP14_SATA0_ACTn             MPP( 14, 0x5, 0, 1, 1,   0    )
+
+#define MPP15_GPIO                   MPP( 15, 0x0, 1, 1, 1,   1    )
+#define MPP15_GE_TXD7                        MPP( 15, 0x1,

0, 1, 1, 1 )
+#define MPP15_NAND_FLASH_WE2n MPP( 15, 0x4,
0, 1, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +3 -0
+#define MPP15_SATA1_ACTn             MPP( 15, 0x5, 0, 1, 1,   0    )
+
+#define MPP16_UART1_RXD                      MPP( 16, 0x0,

1, 0, 1, 1 )
+#define MPP16_GE_RXD4 MPP( 16, 0x1,
1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +4 -0
+#define MPP16_BOOT_NAND_FLASH_REn    MPP( 16, 0x4, 0, 0, 1,   1    )
+#define MPP16_GPIO                   MPP( 16, 0x5, 1, 1, 1,   0    )
+
+#define MPP17_UART1_TXD                      MPP( 17, 0x0,

0, 1, 1, 1 )
+#define MPP17_GE_RXD5 MPP( 17, 0x1,
1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +5 -0
+#define MPP17_BOOT_NAND_FLASH_WEn    MPP( 17, 0x4, 0, 0, 1,   1    )
+#define MPP17_GPIO                   MPP( 17, 0x5, 1, 1, 1,   0    )
+
+#define MPP18_UART1_CTSn             MPP( 18, 0x0, 1, 0, 1,   1    )
+#define MPP18_GE_RXD6                        MPP( 18, 0x1,

1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +4 -0
+#define MPP18_GPIO                   MPP( 18, 0x5, 1, 1, 1,   0    )
+
+#define MPP19_UART1_RTSn             MPP( 19, 0x0, 0, 1, 1,   1    )
+#define MPP19_GE_RXD7                        MPP( 19, 0x1,

1, 0, 1, 1 )

include/asm-arm/arch-orion5x/mpp.h new file +7 -0
+#define MPP19_GPIO                   MPP( 19, 0x5, 1, 1, 1,   0    )
+
+#define MPP_MAX                              19
+
+void orion5x_mpp_conf(unsigned int *mpp_list);
+
+#endif
include/asm-arm/arch-orion5x/orion5x.h new file +43 -0
new file mode 100644
index 0000000..76cb927
@@ -0,0 +1,67 @@
+/*
+ * Copyright (C) 2009 Albert ARIBAUD <[email protected]>
+ *
+ * Based on original Kirkwood support which is
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * Header file for Marvell's Orion SoC with Feroceon CPU core.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _ASM_ARCH_ORION5X_H
+#define _ASM_ARCH_ORION5X_H
+
+#ifndef __ASSEMBLY__
+#include <asm/types.h>
+#include <asm/io.h>
+#endif /* __ASSEMBLY__ */
+
+#if defined (CONFIG_FEROCEON)
+#include <asm/arch/cpu.h>
+
+/* SOC specific definations */
+#define INTREG_BASE                          0xd0000000
+#define ORION5X_REGISTER(x)

(ORION5X_REGS_PHY_BASE + x)

include/asm-arm/arch-orion5x/orion5x.h new file +4 -0
+#define ORION5X_OFFSET_REG                   (INTREG_BASE + 0x20080)
+
+/* Documented registers */
+#define ORION5X_TWSI_BASE

(ORION5X_REGISTER(0x11000))
+#define ORION5X_UART0_BASE
(ORION5X_REGISTER(0x12000))
+#define ORION5X_UART1_BASE
(ORION5X_REGISTER(0x12100))
+#define ORION5X_MPP_BASE
(ORION5X_REGISTER(0x10000))
+#define ORION5X_GPIO_BASE
(ORION5X_REGISTER(0x10100))
+#define ORION5X_CPU_WIN_BASE
(ORION5X_REGISTER(0x20000))
+#define ORION5X_CPU_REG_BASE
(ORION5X_REGISTER(0x20100))
+#define ORION5X_TIMER_BASE
(ORION5X_REGISTER(0x20300))
+#define ORION5X_REG_PCI_BASE
(ORION5X_REGISTER(0x30000))

Quoted 8 lines

+#define ORION5X_REG_PCIE_BASE
(ORION5X_REGISTER(0x40000))
+#define ORION5X_USB20_PORT0_BASE
(ORION5X_REGISTER(0x50000))
+#define ORION5X_USB20_PORT1_BASE
(ORION5X_REGISTER(0xA0000))
+#define ORION5X_EGIGA_BASE
(ORION5X_REGISTER(0x72000))

I hope these are inlined with orion5x and not the result of copy-paste, pls check this carefully

Quoted 35 lines
include/asm-arm/arch-orion5x/orion5x.h new file +8 -0
+
+#if defined (CONFIG_88F5182)
+#include <asm/arch/88f5182.h>
+#else
+#error "SOC Name not defined"
+#endif
+#endif /* CONFIG_FEROCEON */
+#endif /* _ASM_ARCH_ORION5X_H */
include/configs/edminiv2.h new file +21 -0
new file mode 100644
index 0000000..a8036dd
@@ -0,0 +1,158 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,

include/configs/edminiv2.h line 31

Quoted 10 lines
include/configs/edminiv2.h new file +10 -0
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_EDMINIV2_H
+#define _CONFIG_EDMINIV2_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING  " Lacie ED Mini V2"

Short board name will be prefered

Quoted 62 lines
include/configs/edminiv2.h new file +7 -0
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL               1
+#define CONFIG_ARM926EJS     1       /* Basic Architecture */
+#define CONFIG_FEROCEON              1       /* CPU Core

subversion */

include/configs/edminiv2.h new file +5 -0
+#define CONFIG_ORION5X               1       /* SOC Family Name */
+#define CONFIG_88F5182               1       /* SOC Name */
+#define CONFIG_MACH_EDMINIV2 1       /* Machine type */
+
+#define CONFIG_SKIP_LOWLEVEL_INIT    /* disable board

lowlevel_init */

include/configs/edminiv2.h new file +18 -0
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ                1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE  (-4)
+#define CONFIG_SYS_NS16550_CLK               CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1              ORION5X_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you

want to use
+ * for your console driver.
+ */

include/configs/edminiv2.h new file +5 -0
+
+#define CONFIG_CONS_INDEX    1       /*Console on UART0 */
+#define CONFIG_BAUDRATE                      115200
+#define CONFIG_SYS_BAUDRATE_TABLE    { 9600, 19200, 38400, 57600, \
+                                       115200,230400,

460800, 921600 }

include/configs/edminiv2.h new file +11 -0
+/*
+ * FLASH configuration
+ */
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
+#define CONFIG_FLASH_CFI_LEGACY
+
+//#define CONFIG_SYS_FLASH_LEGACY_512Kx8
+#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num

of flash banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max num
of sects on one chip */

include/configs/edminiv2.h new file +2 -0
+#define CONFIG_SYS_FLASH_BASE           0xfff80000
+#define CONFIG_SYS_FLASH_SECTSZ

{16384,8192,8192,32768,65536,65536,65536,65536,65536,65536,65536}

include/configs/edminiv2.h new file +4 -0
+
+/* auto boot */
+#define CONFIG_BOOTDELAY     3       /* default enable autoboot */
+

include/configs/edminiv2.h

Quoted 10 lines
include/configs/edminiv2.h new file +10 -0
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG   1       /* enable passing of ATAGs  */
+#define CONFIG_INITRD_TAG    1       /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1   /* enable memory tag */
+
+#define      CONFIG_SYS_PROMPT       "Marvell>> "    /*

Is this Marvell custom board ?
If not, even you can choose to keep in in boards instead of boards/Marvell/

include/configs/edminiv2.h line 106

Quoted 12 lines

Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O
Buff Size */

include/configs/edminiv2.h new file +9 -0
+#define      CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE \
+             +sizeof(CONFIG_SYS_PROMPT) + 16)        /* Print Buff */
+/*
+ * Commands configuration
+ */
+/*
+ * Disabling many default commands for staggered bring-up
+ */
+#if 0

This is not allowed, pls remove it, or use some defination here
I suggest to use config_cmd_default.h folloed by def/undefs for required commands to inline with other arm boards configuration

Quoted 63 lines
include/configs/edminiv2.h new file +13 -0
+#include <config_cmd_default.h>
+#else
+#define CONFIG_CMD_BDI          /* bdinfo                       */
+#define CONFIG_CMD_CONSOLE      /* coninfo                      */
+#define CONFIG_CMD_ECHO         /* echo arguments               */
+#define CONFIG_CMD_EDITENV      /* editenv                      */
+#define CONFIG_CMD_IMI          /* iminfo                       */
+#define CONFIG_CMD_ITEST        /* Integer (and string) test    */
+#define CONFIG_CMD_FLASH        /* flinfo, erase, protect       */
+#define CONFIG_CMD_IMLS         /* List all found images        */
+#define CONFIG_CMD_LOADB        /* loadb                        */
+#define CONFIG_CMD_LOADS        /* loads                        */
+#define CONFIG_CMD_MEMORY       /* md mm nm mw cp cmp crc

base loop mtest */

include/configs/edminiv2.h new file +20 -0
+#define CONFIG_CMD_MISC         /* Misc functions like sleep etc*/
+#define CONFIG_CMD_RUN          /* run command in env variable  */
+#define CONFIG_CMD_SAVEENV      /* saveenv                      */
+#define CONFIG_CMD_SOURCE       /* "source" command support     */
+#endif
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_ENV
+
+/*
+ *  Environment variables configurations
+ */
+#define CONFIG_ENV_IS_IN_FLASH               1
+#define CONFIG_ENV_SECT_SIZE         0x2000  /* 16K */
+#define CONFIG_ENV_SIZE                      0x2000
+#define CONFIG_ENV_OFFSET            0x4000  /* env starts here */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN        (1024 * 128) /* 128kB

for malloc() */

include/configs/edminiv2.h new file +13 -0
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE     128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_CONSOLE_INFO_QUIET    /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT        /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO       /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE     0x00100000      /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000      /* default load

adr- 8M */

include/configs/edminiv2.h new file +6 -1
+#define CONFIG_SYS_MEMTEST_START 0x00400000  /* 4M */
+#define CONFIG_SYS_MEMTEST_END       0x007fffff      /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000  /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS   16      /* max number of command args */
+
+#endif /* _CONFIG_EDMINIV2_H */
--

1.6.4.4

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#3 lore raw

PATCH 1/1 Initial support for Orion5x SoC and EDMini board

Hi Prafulla and all,

Prafulla Wadaskar a ?crit :

Quoted 17 lines
Quoted 9 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, November 14, 2009 6:32 AM
To: U-Boot at lists.denx.de
Subject: [U-Boot] [PATCH] Initial support for Orion5x SoC and EDMini board

Quoted 7 lines

This patch adds initial u-boot support for the Marvell orion5x SoC and the LAcie ED Mini V2 board--support is limited to serial, flash and environment. Further support will be added as devices common with kirkwood are made useable across SoCs.

---

Quoted 7 lines

Hi Albert

Please break this patch in to small pieces
[...]
Pls edit MAKEALL and Maintainers files too for new board support [...]
Arm: add Edminv2 board support (orion5x based)

Ok.

Quoted 2 lines

Break this in to basic orion5x Soc support patch And individual drivers patches like gpio, uart, etc..

Will do. What exact criteria should I use for splitting patches? Obviously some patches will never be compiled alone, e.g. basic Orion5x support won't be compiled until board support patches come in; also, having SoC and board support without uart support, if it even compiles, will be pretty useless as the resulting u-boot won't even have a console.

Quoted 6 lines

board/Marvell/edminiv2/Makefile line 4

Quoted 3 lines
board/Marvell/edminiv2/Makefile new file +3 -0
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>

This is copy paste mistake, pls correct in all files
You can keep my reference, i.e. based on (ref: boards/Marvell/openrd_base/openrd_base.c)

Ok.

Quoted 3 lines
Quoted 1 line

+TEXT_BASE = 0x00600000

Is this valid for your board? BTW: how much DRAM you have on this board?

Yes it works for the board--I'm using this value for testing. However, in very old and non-reuseable u-boot code, it was 0x00F00000. I'll switch to this in order to minimize the difference between these older u-boots and the current mainline one.

The board has 64M RAM.

Quoted 6 lines
Quoted 4 lines
board/Marvell/edminiv2/edminiv2.c new file +3 -0
+     /*
+      * default gpio configuration
+      * There are maximum 64 gpios controlled through 2 sets

of registers

I don't think there are 64 GPIOs in orion5x

Right, I'll fix the comment. That's 24 (with only 20 actually referenced by the board).

Quoted 4 lines
Quoted 1 line

+ orion5x_config_gpio(EDMINIV2_OE_VAL_LOW, EDMINIV2_OE_LOW);

You can eliminate LOW here, since mpps less than 3 Pls remove word LOW here

Ok.

Quoted 6 lines

cpu/arm926ejs/orion5x/Makefile line 33

Quoted 4 lines
cpu/arm926ejs/orion5x/Makefile new file +2 -0
[...]
+COBJS-y      = dram.o
+COBJS-y      += cpu.o

Pls put these lines in order

Ok. Note this comes directly from kirkwood's Makefile, so the lines are in the same order (dram, cpu, mpp, timer) there too.

Quoted 3 lines
Quoted 1 line

+ * There are maximum 64 Multi-Pourpose Pins on Orion5x

Correct this -64

Will do.

Quoted 4 lines

cpu/arm926ejs/orion5x/cpu.c line 176

Quoted 2 lines
cpu/arm926ejs/orion5x/cpu.c new file +2 -0
+#define PCIE_DEV_ID_OFF         (ORION5X_REG_PCIE_BASE + 0x0000)
+#define PCIE_DEV_REV_OFF        (ORION5X_REG_PCIE_BASE + 0x0008)

Pls move the defination to header file

Will do.

Quoted 42 lines
Quoted 31 lines
cpu/arm926ejs/orion5x/cpu.c new file +31 -0
+     if (dev == MV88F5181_DEV_ID) {
+             dev_name = "MV88F5181";
+             if (rev == MV88F5181_REV_B1) {
+                     rev_name = "B1";
+             } else if (rev == MV88F5181L_REV_A1) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A1";
+             } else if (rev == MV88F5181L_REV_A0) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5182_DEV_ID) {
+             dev_name = "MV88F5182";
+             if (rev == MV88F5182_REV_A2) {
+                     rev_name = "A2";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5281_DEV_ID) {
+             dev_name = "MV88F5281";
+             if (rev == MV88F5281_REV_D2) {
+                     rev_name = "D2";
+             } else if (rev == MV88F5281_REV_D1) {
+                     rev_name = "D1";
+             } else if (rev == MV88F5281_REV_D0) {
+                     rev_name = "D0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }

cpu/arm926ejs/orion5x/cpu.c line 239

Quoted 10 lines
cpu/arm926ejs/orion5x/cpu.c new file +10 -0
+     } else if (dev == MV88F6183_DEV_ID) {
+             dev_name = "MV88F6183";
+             if (rev == MV88F6183_REV_B0) {
+                     rev_name = "B0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else {
+             sprintf(dev_str,"0x%04x", rev);
+             sprintf(rev_str,"0x%02x", rev);
Quoted 1 line

This is common line, pls take out of if-else

Can you be more specific? The outer 'if' sequence deals with device id and I see no no common line in its then/.../else branches, and the inner ifs are for revision and again, I cannot pinpoint the common line. Unless you would want the sprintf's to be done inconditionally before entering the if's?

Note however that there is a typo:

+ } else {
+ sprintf(dev_str,"0x%04x", rev);
+ sprintf(rev_str,"0x%02x", rev);

Should actually be

+ } else {
+ sprintf(dev_str,"0x%04x", dev); <- this is dev, not rev
+ sprintf(rev_str,"0x%02x", rev);

Quoted 9 lines

cpu/arm926ejs/orion5x/cpu.c line 339

Quoted 7 lines
cpu/arm926ejs/orion5x/cpu.c new file +7 -0
+#ifdef CONFIG_ORION5X_EGIGA
+int cpu_eth_init(bd_t *bis)
+{
+     orion5x_egiga_initialize(bis);
+     return 0;
+}
+#endif

Pls do not add this by default, make it a part of egiga driver patch

Will do.

Quoted 7 lines
Quoted 1 line

+ * read feroceon/sheeva core extra feature register

Pls remove name sheeva

Quoted 1 line

+ * write feroceon/sheeva core extra feature register

Same

Right.

Quoted 4 lines
Quoted 2 lines

+ * MBus-L to Mbus Bridge Registers
+ * Ref: Datasheet sec:A.3

Are those references correct?

No, they're not, they're kirkwood's. I'll do a pass on these and fix them wrt orion.

Quoted 3 lines
Quoted 1 line

+#define GPIO_MAX 50

Is this correct defination for Orion?

No. Should be 26. Will fix and add a reference to the specs.

Quoted 3 lines
Quoted 1 line

+ * Kirorion5xood-specific GPIO API

Copy paste error

Worse, actually: it is a ':%s//' search/replace error. Will fix.

Quoted 21 lines
Quoted 21 lines
(quoted diff) +2 -0
+/* Documented registers */
+#define ORION5X_TWSI_BASE

(ORION5X_REGISTER(0x11000))
+#define ORION5X_UART0_BASE
(ORION5X_REGISTER(0x12000))
+#define ORION5X_UART1_BASE
(ORION5X_REGISTER(0x12100))
+#define ORION5X_MPP_BASE
(ORION5X_REGISTER(0x10000))
+#define ORION5X_GPIO_BASE
(ORION5X_REGISTER(0x10100))
+#define ORION5X_CPU_WIN_BASE
(ORION5X_REGISTER(0x20000))
+#define ORION5X_CPU_REG_BASE
(ORION5X_REGISTER(0x20100))
+#define ORION5X_TIMER_BASE
(ORION5X_REGISTER(0x20300))
+#define ORION5X_REG_PCI_BASE
(ORION5X_REGISTER(0x30000))
+#define ORION5X_REG_PCIE_BASE
(ORION5X_REGISTER(0x40000))

Quoted 8 lines
Quoted 6 lines

+#define ORION5X_USB20_PORT0_BASE
(ORION5X_REGISTER(0x50000))
+#define ORION5X_USB20_PORT1_BASE
(ORION5X_REGISTER(0xA0000))
+#define ORION5X_EGIGA_BASE
(ORION5X_REGISTER(0x72000))

I hope these are inlined with orion5x and not the result of copy-paste, pls check this carefully

Yes they are in line--while I started off a copy of the kirkwood list, I took extra care to match each one with Orion5x's spec.

Quoted 3 lines
Quoted 1 line

+#define CONFIG_IDENT_STRING " Lacie ED Mini V2"

Short board name will be prefered

Understood, will put " EDMiniV2".

Quoted 4 lines
Quoted 1 line

+#define CONFIG_SYS_PROMPT "Marvell>> " /*

Is this Marvell custom board ?
If not, even you can choose to keep in in boards instead of boards/Marvell/

No, it's not a Marvell custom board, it's a LaCie product board. I'll move the board to boards/ directly (or maybe "boards/lacie", to provide
a home for other lacie boards? Any best pratice here to follow?) and
change the prompt to "EDMiniV2".

Quoted 7 lines

include/configs/edminiv2.h line 106

Quoted 4 lines
include/configs/edminiv2.h new file +4 -0
+/*
+ * Disabling many default commands for staggered bring-up
+ */
+#if 0

This is not allowed, pls remove it, or use some defination here
I suggest to use config_cmd_default.h folloed by def/undefs for required commands to inline with other arm boards configuration

Will do.

Thanks a lot for the review. I'll fix the issues you pointed out and resubmit a patchset.

Amicalement,

Signature · 1 line
Albert.
#4 lore raw

PATCH 1/1 Initial support for Orion5x SoC and EDMini board

Quoted 43 lines

-----Original Message-----
From: Albert ARIBAUD [mailto:albert.aribaud at free.fr]
Sent: Saturday, November 14, 2009 2:53 PM
To: Prafulla Wadaskar
Cc: U-Boot at lists.denx.de; Ashish Karkare; Prabhanjan Sarnaik
Subject: Re: [U-Boot] [PATCH] Initial support for Orion5x SoC and EDMini board

Hi Prafulla and all,

Prafulla Wadaskar a ?crit :

Quoted 17 lines
Quoted 9 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, November 14, 2009 6:32 AM
To: U-Boot at lists.denx.de
Subject: [U-Boot] [PATCH] Initial support for Orion5x SoC and EDMini board

Quoted 7 lines

This patch adds initial u-boot support for the Marvell orion5x SoC and the LAcie ED Mini V2 board--support is limited to serial, flash and environment. Further support will be added as devices common with kirkwood are made useable across SoCs.

---

Quoted 7 lines

Hi Albert

Please break this patch in to small pieces
[...]
Pls edit MAKEALL and Maintainers files too for new board support [...]
Arm: add Edminv2 board support (orion5x based)

Ok.

Quoted 2 lines

Break this in to basic orion5x Soc support patch And individual drivers patches like gpio, uart, etc..

Quoted 8 lines

Will do. What exact criteria should I use for splitting patches? Obviously some patches will never be compiled alone, e.g. basic Orion5x
support won't be compiled until board support patches come in; also, having SoC and board support without uart support, if it even compiles,
will be pretty useless as the resulting u-boot won't even have a console.

It should be patch series with properly addressed dependencies i.e.
(1/4)basic orion soc support patch
(2/4)orion gpio driver
(3/4)orion UART support
(4/4) Board support patch

All patches when applied in series should build u-boot for respective board.
The spilt has to be done carefully because individual patch may be applied to different repositories, like nandf to u-boot-nand.git, basic orion support to u-boot-marvell.git, egiga driver patch will go in u-boot-net.git etc

Quoted 11 lines
Quoted 3 lines
Quoted 1 line

+TEXT_BASE = 0x00600000

Is this valid for your board? BTW: how much DRAM you have

on this board?

Yes it works for the board--I'm using this value for testing. However,
in very old and non-reuseable u-boot code, it was 0x00F00000. I'll switch to this in order to minimize the difference between these older
u-boots and the current mainline one.

I will suggest to use lower part of available ram for this

Quoted 9 lines
Quoted 6 lines

cpu/arm926ejs/orion5x/Makefile line 33

Quoted 4 lines
cpu/arm926ejs/orion5x/Makefile new file +2 -0
[...]
+COBJS-y      = dram.o
+COBJS-y      += cpu.o

Pls put these lines in order

Ok. Note this comes directly from kirkwood's Makefile, so the lines are

Thanks , I will provide separate patch for this

Quoted 43 lines
Quoted 43 lines
Quoted 42 lines
cpu/arm926ejs/orion5x/cpu.c new file +41 -0
+     if (dev == MV88F5181_DEV_ID) {
+             dev_name = "MV88F5181";
+             if (rev == MV88F5181_REV_B1) {
+                     rev_name = "B1";
+             } else if (rev == MV88F5181L_REV_A1) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A1";
+             } else if (rev == MV88F5181L_REV_A0) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5182_DEV_ID) {
+             dev_name = "MV88F5182";
+             if (rev == MV88F5182_REV_A2) {
+                     rev_name = "A2";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5281_DEV_ID) {
+             dev_name = "MV88F5281";
+             if (rev == MV88F5281_REV_D2) {
+                     rev_name = "D2";
+             } else if (rev == MV88F5281_REV_D1) {
+                     rev_name = "D1";
+             } else if (rev == MV88F5281_REV_D0) {
+                     rev_name = "D0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F6183_DEV_ID) {
+             dev_name = "MV88F6183";
+             if (rev == MV88F6183_REV_B0) {
+                     rev_name = "B0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else {
+             sprintf(dev_str,"0x%04x", rev);
+             sprintf(rev_str,"0x%02x", rev);
Quoted 4 lines
Quoted 1 line

This is common line, pls take out of if-else

Can you be more specific? The outer 'if' sequence deals with device id

Okay I will take this back
Whereas I found
+ sprintf(rev_str,"0x%02x", rev);
At so many places, can you reduce it?

Quoted 10 lines
Quoted 2 lines

Is this Marvell custom board ?
If not, even you can choose to keep in in boards instead of

boards/Marvell/

No, it's not a Marvell custom board, it's a LaCie product board. I'll move the board to boards/ directly (or maybe "boards/lacie", to provide
a home for other lacie boards? Any best pratice here to
follow?) and
change the prompt to "EDMiniV2".

That's good approach for this board, if you are planning to put support for more Lacie boards, then its better to have boards/lacie

Regards..
Prafulla . .

#5 lore raw

PATCH 1/1 Initial support for Orion5x SoC and EDMini board

Hi again Prafulla,

Prafulla Wadaskar a ?crit :

Quoted 17 lines
Quoted 9 lines
Quoted 2 lines

Break this in to basic orion5x Soc support patch And individual drivers patches like gpio, uart, etc..

Will do. What exact criteria should I use for splitting patches? Obviously some patches will never be compiled alone, e.g. basic Orion5x support won't be compiled until board support patches come in; also, having SoC and board support without uart support, if it even compiles, will be pretty useless as the resulting u-boot won't even have a console.

It should be patch series with properly addressed dependencies i.e.
(1/4)basic orion soc support patch
(2/4)orion gpio driver
(3/4)orion UART support
(4/4) Board support patch

Quoted 3 lines

All patches when applied in series should build u-boot for respective board.
The spilt has to be done carefully because individual patch may be applied to different repositories, like nandf to u-boot-nand.git, basic orion support to u-boot-marvell.git, egiga driver patch will go in u-boot-net.git etc

Duly noted. Currently, I only add support for SoC, UART and NOT FLASH (not NAND) so only u-boot-marvell.git needs to be considered; I'll keep other repos in mind for upcoming patches like egiga and others.

Quoted 11 lines
Quoted 9 lines
Quoted 2 lines
Quoted 1 line

+TEXT_BASE = 0x00600000

Is this valid for your board? BTW: how much DRAM you have

on this board?

Yes it works for the board--I'm using this value for testing. However,
in very old and non-reuseable u-boot code, it was 0x00F00000. I'll switch to this in order to minimize the difference between these older u-boots and the current mainline one.

I will suggest to use lower part of available ram for this

Understood. Note the 0x00600000 value comes from kirkwood too, in case this matters.

Quoted 41 lines
Quoted 41 lines
Quoted 41 lines
Quoted 41 lines
cpu/arm926ejs/orion5x/cpu.c new file +41 -0
+     if (dev == MV88F5181_DEV_ID) {
+             dev_name = "MV88F5181";
+             if (rev == MV88F5181_REV_B1) {
+                     rev_name = "B1";
+             } else if (rev == MV88F5181L_REV_A1) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A1";
+             } else if (rev == MV88F5181L_REV_A0) {
+                     dev_name = "MV88F5181L";
+                     rev_name = "A0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5182_DEV_ID) {
+             dev_name = "MV88F5182";
+             if (rev == MV88F5182_REV_A2) {
+                     rev_name = "A2";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F5281_DEV_ID) {
+             dev_name = "MV88F5281";
+             if (rev == MV88F5281_REV_D2) {
+                     rev_name = "D2";
+             } else if (rev == MV88F5281_REV_D1) {
+                     rev_name = "D1";
+             } else if (rev == MV88F5281_REV_D0) {
+                     rev_name = "D0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else if (dev == MV88F6183_DEV_ID) {
+             dev_name = "MV88F6183";
+             if (rev == MV88F6183_REV_B0) {
+                     rev_name = "B0";
+             } else {
+                     sprintf(rev_str,"0x%02x", rev);
+             }
+     } else {
+             sprintf(dev_str,"0x%04x", rev);
+             sprintf(rev_str,"0x%02x", rev);
Quoted 8 lines
Quoted 3 lines
Quoted 1 line

This is common line, pls take out of if-else

Can you be more specific? The outer 'if' sequence deals with device id

Okay I will take this back
Whereas I found
+ sprintf(rev_str,"0x%02x", rev);
At so many places, can you reduce it?

Hmm yes, I think I can start by setting dev_name/rev_name tu NULL, go through the ifs and set dev_name/rev_name only if appropriate, and then do the sprintf()s only if dev_name/rev_name are still NULL after the ifs.

Quoted 4 lines
Quoted 4 lines
Quoted 2 lines

Is this Marvell custom board ?
If not, even you can choose to keep in in boards instead of

boards/Marvell/

Quoted 8 lines
Quoted 6 lines

No, it's not a Marvell custom board, it's a LaCie product board. I'll move the board to boards/ directly (or maybe "boards/lacie", to provide
a home for other lacie boards? Any best pratice here to
follow?) and
change the prompt to "EDMiniV2".

That's good approach for this board, if you are planning to put support for more Lacie boards, then its better to have boards/lacie

I guess there's at least a second one to come, so I'll go for the boards/lacie/* approach.

Quoted 2 lines

Regards..
Prafulla . .

Thanks again!

Amicalement,

Signature · 1 line
Albert.