Skip to contentSkip to conversation

TI: DaVinci: Updating EMAC driver for DM365 and DM646x

PATCH New s-paulraj at ti.com 3 participants 3 messages Nov 13, 2009 – Nov 16, 2009 Network drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 TI: DaVinci: Updating EMAC driver for DM365 and DM646x

From: Sandeep Paulraj <[email protected]>

The EMAC IP on DM365 and DM646x is slightly different from that on DM644x. This patch updates the DaVinci EMAC driver so that EMAC becomes operational on DM365 in U-Boot. A flag 'CONFIG_DAVINCI_EMAC_VERSION2' is used in the driver. This flag will need to be defined in the DM365 config file.

---
The same modifications work on DM646x in a slightly older version of U-Boot. So when enabled this should work on the DM6467 EVM as well. This has at this point of time not been tested on the DM6467 in the latest version of U-Boot.

 drivers/net/davinci_emac.c |   79 ++++++++++++++++++++++++++++++++++++++++++-
 1 files changed, 77 insertions(+), 2 deletions(-)
drivers/net/davinci_emac.c +77 -2
index fa8cee4..1df98e9 100644
@@ -107,6 +107,33 @@ static void davinci_eth_mdio_enable(void)
 	while (adap_mdio->CONTROL & MDIO_CONTROL_IDLE) {;}
 }
 
+/* Read a PHY register via MDIO inteface */
+static int mdio_read(int phy_addr, int reg_num)
+{
+	adap_mdio->USERACCESS0 = MDIO_USERACCESS0_GO |
+					MDIO_USERACCESS0_WRITE_READ |
+					((reg_num & 0x1F) << 21) |
+					((phy_addr & 0x1F) << 16);
+
+	/* Wait for command to complete */
+	while (adap_mdio->USERACCESS0 & MDIO_USERACCESS0_GO);
+
+	return adap_mdio->USERACCESS0 & 0xFFFF;
+}
+
+/* Write to a PHY register via MDIO inteface */
+void mdio_write(int phy_addr, int reg_num, unsigned int data)
+{
+	/* Wait for User access register to be ready */
+	while (adap_mdio->USERACCESS0 & MDIO_USERACCESS0_GO);
+
+	adap_mdio->USERACCESS0 = MDIO_USERACCESS0_GO |
+					MDIO_USERACCESS0_WRITE_WRITE |
+					((reg_num & 0x1F) << 21) |
+					((phy_addr & 0x1F) << 16) |
+					(data & 0xFFFF);
+}
+
 /*
  * Tries to find an active connected PHY. Returns 1 if address if found.
  * If no active PHY (or more than one PHY) found returns 0.
@@ -248,6 +275,31 @@ static int davinci_mii_phy_write(char *devname, unsigned char addr, unsigned cha
 
 #endif
 
+static void emac_gigabit_enable(void)
+{
+	int temp;
+
+	temp = mdio_read(EMAC_MDIO_PHY_NUM, 0);
+
+	if (temp & (1 << 6)) {
+		/*
+		 * Check if link detected is giga-bit
+		 * If Gigabit mode detected, enable gigbit in MAC and PHY
+		 */
+		adap_emac->MACCONTROL |= EMAC_MACCONTROL_GIGFORCE |
+						EMAC_MACCONTROL_GIGABIT_ENABLE;
+
+		/*
+		 * The SYS_CLK which feeds the SOC for giga-bit operation
+		 * does not seem to be enabled after reset as expected.
+		 * Force enabling SYS_CLK by writing to the PHY
+		 */
+		temp = mdio_read(EMAC_MDIO_PHY_NUM, 22);
+		temp |= (1 << 4);
+		mdio_write(EMAC_MDIO_PHY_NUM, 22, temp);
+	}
+}
+
 
 /* Eth device open */
 static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
@@ -261,10 +313,15 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	/* Reset EMAC module and disable interrupts in wrapper */
 	adap_emac->SOFTRESET = 1;
 	while (adap_emac->SOFTRESET != 0) {;}
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	adap_ewrap->SOFTRST = 1;
+	while (adap_ewrap->SOFTRST != 0);
+#else
 	adap_ewrap->EWCTL = 0;
 	for (cnt = 0; cnt < 5; cnt++) {
 		clkdiv = adap_ewrap->EWCTL;
 	}
+#endif
 
 	rx_desc = emac_rx_desc;
 
@@ -282,6 +339,10 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	adap_emac->MACADDRLO =
 		(davinci_eth_mac_addr[5] << 8) |
 		(davinci_eth_mac_addr[4]);
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	/* Set the Match and Valid Bits */
+	adap_emac->MACADDRLO |= (1 << 19) | (1 << 20);
+#endif
 
 	adap_emac->MACHASH1 = 0;
 	adap_emac->MACHASH2 = 0;
@@ -347,8 +408,15 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	clkdiv = (EMAC_MDIO_BUS_FREQ / EMAC_MDIO_CLOCK_FREQ) - 1;
 	adap_mdio->CONTROL = ((clkdiv & 0xff) | MDIO_CONTROL_ENABLE | MDIO_CONTROL_FAULT);
 
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	/* We need to wait for MDIO to start */
+	udelay(1000);
+#endif
+
 	if (!phy.get_link_speed(active_phy_addr))
 		return(0);
+	else
+		emac_gigabit_enable();
 
 	/* Start receive process */
 	adap_emac->RX0HDP = (u_int32_t)emac_rx_desc;
@@ -411,7 +479,11 @@ static void davinci_eth_close(struct eth_device *dev)
 
 	/* Reset EMAC module and disable interrupts in wrapper */
 	adap_emac->SOFTRESET = 1;
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	adap_ewrap->SOFTRST = 1;
+#else
 	adap_ewrap->EWCTL = 0;
+#endif
 
 	debug_emac("- emac_close\n");
 }
@@ -433,7 +505,8 @@ static int davinci_eth_send_packet (struct eth_device *dev,
 	if (!phy.get_link_speed (active_phy_addr)) {
 		printf ("WARN: emac_send_packet: No link\n");
 		return (ret_status);
-	}
+	} else
+		emac_gigabit_enable();
 
 	/* Check packet size and if < EMAC_MIN_ETHERNET_PKT_SIZE, pad it up */
 	if (length < EMAC_MIN_ETHERNET_PKT_SIZE) {
@@ -456,7 +529,9 @@ static int davinci_eth_send_packet (struct eth_device *dev,
 		if (!phy.get_link_speed (active_phy_addr)) {
 			davinci_eth_ch_teardown (EMAC_CH_TX);
 			return (ret_status);
-		}
+		} else
+			emac_gigabit_enable();
+
 		if (adap_emac->TXINTSTATRAW & 0x01) {
 			ret_status = length;
 			break;
Signature · 1 line
1.6.0.4
#1 lore raw

PATCH 1/1 TI: DaVinci: Updating EMAC driver for DM365 and DM646x

Hi Sandeep,

Quoted 74 lines · s-paulraj at ti.com

From: Sandeep Paulraj <[email protected]>

The EMAC IP on DM365 and DM646x is slightly different from that on DM644x. This patch updates the DaVinci EMAC driver so that EMAC becomes operational on DM365 in U-Boot. A flag 'CONFIG_DAVINCI_EMAC_VERSION2' is used in the driver. This flag will need to be defined in the DM365 config file.

---
The same modifications work on DM646x in a slightly older version of U-Boot. So when enabled this should work on the DM6467 EVM as well. This has at this point of time not been tested on the DM6467 in the latest version of U-Boot.

 drivers/net/davinci_emac.c |   79 ++++++++++++++++++++++++++++++++++++++++++-
 1 files changed, 77 insertions(+), 2 deletions(-)
drivers/net/davinci_emac.c +42 -0
index fa8cee4..1df98e9 100644
@@ -107,6 +107,33 @@ static void davinci_eth_mdio_enable(void)
 	while (adap_mdio->CONTROL & MDIO_CONTROL_IDLE) {;}
 }
 
+/* Read a PHY register via MDIO inteface */
+static int mdio_read(int phy_addr, int reg_num)
+{
+	adap_mdio->USERACCESS0 = MDIO_USERACCESS0_GO |
+					MDIO_USERACCESS0_WRITE_READ |
+					((reg_num & 0x1F) << 21) |
+					((phy_addr & 0x1F) << 16);
+
+	/* Wait for command to complete */
+	while (adap_mdio->USERACCESS0 & MDIO_USERACCESS0_GO);
+
+	return adap_mdio->USERACCESS0 & 0xFFFF;
+}
+
+/* Write to a PHY register via MDIO inteface */
+void mdio_write(int phy_addr, int reg_num, unsigned int data)
+{
+	/* Wait for User access register to be ready */
+	while (adap_mdio->USERACCESS0 & MDIO_USERACCESS0_GO);
+
+	adap_mdio->USERACCESS0 = MDIO_USERACCESS0_GO |
+					MDIO_USERACCESS0_WRITE_WRITE |
+					((reg_num & 0x1F) << 21) |
+					((phy_addr & 0x1F) << 16) |
+					(data & 0xFFFF);
+}
+
 /*
  * Tries to find an active connected PHY. Returns 1 if address if found.
  * If no active PHY (or more than one PHY) found returns 0.
@@ -248,6 +275,31 @@ static int davinci_mii_phy_write(char *devname, unsigned char addr, unsigned cha
 
 #endif
 
+static void emac_gigabit_enable(void)
+{
+	int temp;
+
+	temp = mdio_read(EMAC_MDIO_PHY_NUM, 0);
+
+	if (temp & (1 << 6)) {
+		/*
+		 * Check if link detected is giga-bit
+		 * If Gigabit mode detected, enable gigbit in MAC and PHY
+		 */
+		adap_emac->MACCONTROL |= EMAC_MACCONTROL_GIGFORCE |
+						EMAC_MACCONTROL_GIGABIT_ENABLE;
+
+		/*

drivers/net/davinci_emac.c static int davinci_mii_phy_write(char *devname, unsigned char addr, unsigned cha · line 302

Quoted 10 lines
drivers/net/davinci_emac.c +10 -0
+		 * The SYS_CLK which feeds the SOC for giga-bit operation
+		 * does not seem to be enabled after reset as expected.
+		 * Force enabling SYS_CLK by writing to the PHY
+		 */
+		temp = mdio_read(EMAC_MDIO_PHY_NUM, 22);
+		temp |= (1 << 4);
+		mdio_write(EMAC_MDIO_PHY_NUM, 22, temp);
+	}
+}
+

Do all DaVinci boards have gigabit? Unsurprisingly, I'm coming from the point of view that DA830 at least doesn't have this. I wonder if it going to be safe to modify these bits across the DaVinci range?

Quoted 59 lines
drivers/net/davinci_emac.c +20 -0
 /* Eth device open */
 static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
@@ -261,10 +313,15 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	/* Reset EMAC module and disable interrupts in wrapper */
 	adap_emac->SOFTRESET = 1;
 	while (adap_emac->SOFTRESET != 0) {;}
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	adap_ewrap->SOFTRST = 1;
+	while (adap_ewrap->SOFTRST != 0);
+#else
 	adap_ewrap->EWCTL = 0;
 	for (cnt = 0; cnt < 5; cnt++) {
 		clkdiv = adap_ewrap->EWCTL;
 	}
+#endif
 
 	rx_desc = emac_rx_desc;
 
@@ -282,6 +339,10 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	adap_emac->MACADDRLO =
 		(davinci_eth_mac_addr[5] << 8) |
 		(davinci_eth_mac_addr[4]);
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	/* Set the Match and Valid Bits */
+	adap_emac->MACADDRLO |= (1 << 19) | (1 << 20);
+#endif
 
 	adap_emac->MACHASH1 = 0;
 	adap_emac->MACHASH2 = 0;
@@ -347,8 +408,15 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	clkdiv = (EMAC_MDIO_BUS_FREQ / EMAC_MDIO_CLOCK_FREQ) - 1;
 	adap_mdio->CONTROL = ((clkdiv & 0xff) | MDIO_CONTROL_ENABLE | MDIO_CONTROL_FAULT);
 
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	/* We need to wait for MDIO to start */
+	udelay(1000);
+#endif
+
 	if (!phy.get_link_speed(active_phy_addr))
 		return(0);
+	else
+		emac_gigabit_enable();
 
 	/* Start receive process */
 	adap_emac->RX0HDP = (u_int32_t)emac_rx_desc;
@@ -411,7 +479,11 @@ static void davinci_eth_close(struct eth_device *dev)
 
 	/* Reset EMAC module and disable interrupts in wrapper */
 	adap_emac->SOFTRESET = 1;
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	adap_ewrap->SOFTRST = 1;
+#else
 	adap_ewrap->EWCTL = 0;
+#endif
 
 	debug_emac("- emac_close\n");
 }

drivers/net/davinci_emac.c static int davinci_eth_send_packet (struct eth_device *dev, · line 509

Quoted 6 lines
drivers/net/davinci_emac.c +2 -1
@@ -433,7 +505,8 @@ static int davinci_eth_send_packet (struct eth_device *dev,
 	if (!phy.get_link_speed (active_phy_addr)) {
 		printf ("WARN: emac_send_packet: No link\n");
 		return (ret_status);
-	}
+	} else
+		emac_gigabit_enable();

Here and below, is it a good idea to be enabling gigabit on each packet send? It seem like a lot of overhead.

Quoted 14 lines
drivers/net/davinci_emac.c +3 -1
 	/* Check packet size and if < EMAC_MIN_ETHERNET_PKT_SIZE, pad it up */
 	if (length < EMAC_MIN_ETHERNET_PKT_SIZE) {
@@ -456,7 +529,9 @@ static int davinci_eth_send_packet (struct eth_device *dev,
 		if (!phy.get_link_speed (active_phy_addr)) {
 			davinci_eth_ch_teardown (EMAC_CH_TX);
 			return (ret_status);
-		}
+		} else
+			emac_gigabit_enable();
+
 		if (adap_emac->TXINTSTATRAW & 0x01) {
 			ret_status = length;
 			break;
#2 lore raw

PATCH 1/1 TI: DaVinci: Updating EMAC driver for DM365 and DM646x

Hi Nick,

Quoted 93 lines

-----Original Message-----
From: Nick Thompson [mailto:nick.thompson at gefanuc.com]
Sent: Monday, November 16, 2009 11:47 AM
To: Paulraj, Sandeep
Cc: u-boot at lists.denx.de; biggerbadderben at gmail.com
Subject: Re: [U-Boot] [PATCH] TI: DaVinci: Updating EMAC driver for DM365 and DM646x

Hi Sandeep,

Quoted 8 lines · s-paulraj at ti.com

From: Sandeep Paulraj <[email protected]>

The EMAC IP on DM365 and DM646x is slightly different from that on DM644x. This patch updates the DaVinci EMAC driver so that EMAC becomes operational on DM365 in U-Boot. A flag 'CONFIG_DAVINCI_EMAC_VERSION2' is used in the driver. This flag will need to be defined in the DM365 config file.

Quoted 5 lines

---
The same modifications work on DM646x in a slightly older version of U-Boot. So when enabled this should work on the DM6467 EVM as well. This has at this point of time not been tested on the DM6467 in the

latest

Quoted 2 lines

version of U-Boot.

 drivers/net/davinci_emac.c |   79

++++++++++++++++++++++++++++++++++++++++++-

Quoted 29 lines
 1 files changed, 77 insertions(+), 2 deletions(-)
drivers/net/davinci_emac.c +19 -0
index fa8cee4..1df98e9 100644
@@ -107,6 +107,33 @@ static void davinci_eth_mdio_enable(void)
 	while (adap_mdio->CONTROL & MDIO_CONTROL_IDLE) {;}
 }
 
+/* Read a PHY register via MDIO inteface */
+static int mdio_read(int phy_addr, int reg_num)
+{
+	adap_mdio->USERACCESS0 = MDIO_USERACCESS0_GO |
+					MDIO_USERACCESS0_WRITE_READ |
+					((reg_num & 0x1F) << 21) |
+					((phy_addr & 0x1F) << 16);
+
+	/* Wait for command to complete */
+	while (adap_mdio->USERACCESS0 & MDIO_USERACCESS0_GO);
+
+	return adap_mdio->USERACCESS0 & 0xFFFF;
+}
+
+/* Write to a PHY register via MDIO inteface */
+void mdio_write(int phy_addr, int reg_num, unsigned int data)
+{
+	/* Wait for User access register to be ready */
+	while (adap_mdio->USERACCESS0 & MDIO_USERACCESS0_GO);

drivers/net/davinci_emac.c static void davinci_eth_mdio_enable(void) · line 138

Quoted 10 lines
drivers/net/davinci_emac.c +8 -0
+
+	adap_mdio->USERACCESS0 = MDIO_USERACCESS0_GO |
+					MDIO_USERACCESS0_WRITE_WRITE |
+					((reg_num & 0x1F) << 21) |
+					((phy_addr & 0x1F) << 16) |
+					(data & 0xFFFF);
+}
+
 /*
  * Tries to find an active connected PHY. Returns 1 if address if

found.

drivers/net/davinci_emac.c static int davinci_mii_phy_write(char *devname,

Quoted 2 lines
drivers/net/davinci_emac.c +0 -0
  * If no active PHY (or more than one PHY) found returns 0.
@@ -248,6 +275,31 @@ static int davinci_mii_phy_write(char *devname,

unsigned char addr, unsigned cha

Quoted 22 lines
drivers/net/davinci_emac.c +19 -0
 #endif
 
+static void emac_gigabit_enable(void)
+{
+	int temp;
+
+	temp = mdio_read(EMAC_MDIO_PHY_NUM, 0);
+
+	if (temp & (1 << 6)) {
+		/*
+		 * Check if link detected is giga-bit
+		 * If Gigabit mode detected, enable gigbit in MAC and PHY
+		 */
+		adap_emac->MACCONTROL |= EMAC_MACCONTROL_GIGFORCE |
+						EMAC_MACCONTROL_GIGABIT_ENABLE;
+
+		/*
+		 * The SYS_CLK which feeds the SOC for giga-bit operation
+		 * does not seem to be enabled after reset as expected.
+		 * Force enabling SYS_CLK by writing to the PHY
+		 */
Quoted 8 lines

drivers/net/davinci_emac.c static int davinci_mii_phy_write(char *devname, unsigned char addr, unsigned cha · line 302

Quoted 6 lines
drivers/net/davinci_emac.c +6 -0
+		temp = mdio_read(EMAC_MDIO_PHY_NUM, 22);
+		temp |= (1 << 4);
+		mdio_write(EMAC_MDIO_PHY_NUM, 22, temp);
+	}
+}
+

Do all DaVinci boards have gigabit?

No they do not

Quoted 5 lines

Unsurprisingly, I'm coming from the
point
of view that DA830 at least doesn't have this. I wonder if it going to be safe
to modify these bits across the DaVinci range?

This function will be called by only those that have this feature.

This function will be called by only DM365 and DM6467.

Quoted 66 lines

drivers/net/davinci_emac.c static int davinci_eth_open(struct eth_device

Quoted 5 lines
drivers/net/davinci_emac.c +0 -0
 /* Eth device open */
 static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
@@ -261,10 +313,15 @@ static int davinci_eth_open(struct eth_device

*dev, bd_t *bis)

drivers/net/davinci_emac.c static int davinci_eth_open(struct eth_device *dev,

Quoted 16 lines
drivers/net/davinci_emac.c +5 -0
 	/* Reset EMAC module and disable interrupts in wrapper */
 	adap_emac->SOFTRESET = 1;
 	while (adap_emac->SOFTRESET != 0) {;}
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	adap_ewrap->SOFTRST = 1;
+	while (adap_ewrap->SOFTRST != 0);
+#else
 	adap_ewrap->EWCTL = 0;
 	for (cnt = 0; cnt < 5; cnt++) {
 		clkdiv = adap_ewrap->EWCTL;
 	}
+#endif
 
 	rx_desc = emac_rx_desc;
 
@@ -282,6 +339,10 @@ static int davinci_eth_open(struct eth_device *dev,

bd_t *bis)

drivers/net/davinci_emac.c static int davinci_eth_open(struct eth_device *dev,

Quoted 11 lines
drivers/net/davinci_emac.c +4 -0
 	adap_emac->MACADDRLO =
 		(davinci_eth_mac_addr[5] << 8) |
 		(davinci_eth_mac_addr[4]);
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	/* Set the Match and Valid Bits */
+	adap_emac->MACADDRLO |= (1 << 19) | (1 << 20);
+#endif
 
 	adap_emac->MACHASH1 = 0;
 	adap_emac->MACHASH2 = 0;
@@ -347,8 +408,15 @@ static int davinci_eth_open(struct eth_device *dev,

bd_t *bis)

drivers/net/davinci_emac.c static int davinci_eth_open(struct eth_device *dev, · line 409

Quoted 2 lines
drivers/net/davinci_emac.c +0 -0
 	clkdiv = (EMAC_MDIO_BUS_FREQ / EMAC_MDIO_CLOCK_FREQ) - 1;
 	adap_mdio->CONTROL = ((clkdiv & 0xff) | MDIO_CONTROL_ENABLE |

MDIO_CONTROL_FAULT);

drivers/net/davinci_emac.c static void davinci_eth_close(struct eth_device

Quoted 14 lines
drivers/net/davinci_emac.c +7 -0
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	/* We need to wait for MDIO to start */
+	udelay(1000);
+#endif
+
 	if (!phy.get_link_speed(active_phy_addr))
 		return(0);
+	else
+		emac_gigabit_enable();
 
 	/* Start receive process */
 	adap_emac->RX0HDP = (u_int32_t)emac_rx_desc;
@@ -411,7 +479,11 @@ static void davinci_eth_close(struct eth_device

*dev)

drivers/net/davinci_emac.c static int davinci_eth_send_packet (struct

Quoted 12 lines
drivers/net/davinci_emac.c +4 -0
 	/* Reset EMAC module and disable interrupts in wrapper */
 	adap_emac->SOFTRESET = 1;
+#if defined(CONFIG_DAVINCI_EMAC_VERSION2)
+	adap_ewrap->SOFTRST = 1;
+#else
 	adap_ewrap->EWCTL = 0;
+#endif
 
 	debug_emac("- emac_close\n");
 }
@@ -433,7 +505,8 @@ static int davinci_eth_send_packet (struct

eth_device *dev,

Quoted 10 lines

drivers/net/davinci_emac.c static int davinci_eth_send_packet (struct eth_device *dev, · line 509

Quoted 6 lines
drivers/net/davinci_emac.c +2 -1
 	if (!phy.get_link_speed (active_phy_addr)) {
 		printf ("WARN: emac_send_packet: No link\n");
 		return (ret_status);
-	}
+	} else
+		emac_gigabit_enable();

Here and below, is it a good idea to be enabling gigabit on each packet send?
It seem like a lot of overhead.

I see the issue.

Quoted 7 lines

drivers/net/davinci_emac.c static int davinci_eth_send_packet (struct · line 510

Quoted 3 lines
drivers/net/davinci_emac.c +0 -0
 	/* Check packet size and if < EMAC_MIN_ETHERNET_PKT_SIZE, pad it up

*/

drivers/net/davinci_emac.c static int davinci_eth_send_packet (struct

Quoted 2 lines
drivers/net/davinci_emac.c +0 -0
 	if (length < EMAC_MIN_ETHERNET_PKT_SIZE) {
@@ -456,7 +529,9 @@ static int davinci_eth_send_packet (struct

eth_device *dev,

Quoted 10 lines

drivers/net/davinci_emac.c static int davinci_eth_send_packet (struct eth_device *dev, · line 537

Quoted 10 lines
drivers/net/davinci_emac.c +3 -1
 		if (!phy.get_link_speed (active_phy_addr)) {
 			davinci_eth_ch_teardown (EMAC_CH_TX);
 			return (ret_status);
-		}
+		} else
+			emac_gigabit_enable();
+
 		if (adap_emac->TXINTSTATRAW & 0x01) {
 			ret_status = length;
 			break;

I am also open to collaborating with you on submitting just 1 patch with updates to this driver so that we start supporting DM365, DM6467 and DA8xx.

Let me know your thoughts.

Sandeep