CH???, Bandwidth 8MHz, Fec_Hi 1/2, Modulation QAM64, Mode 8K, Guard 1/4, fails to tune\demux
02:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH
Technotrend-Budget/Hauppauge WinTV-NOVA-T DVB card
Flags: bus master, medium devsel, latency 32, IRQ 17 Memory at e3001000 (32-bit, non-prefetchable) [size=512] Kernel driver in use: budget dvb
Kernel modules: budget
Howdy.
I'm afraid that your posting is horribly unclear, with the apparently important information present in the Subject: header, as such:
``Subject : Re: CH???, Bandwidth 8MHz, Fec_Hi 1/2, Modulation QAM64, Mode 8K,
Guard 1/4, fails to tune\demux''
I'm going to go out on a limb and ass-u-me that you are writing to ask about the DVB-H multiplex which is broadcast by SBC on several different allocated SFN frequencies throughout Confœderatio Helvetica. The DVB-T services use a more conventional FEC of 5/6 in a denser network of transmitters.
Note that these frequencies are partly re-used in areas where it is possible to receive simultaneously the out-of-area DVB-T signals on the same frequency, which renders both impossible to receive, in spite of a healthy signal strength. I don't know if this might affect you.
Not only is this multiplex sent in DVB-H standard, but it is also a subscription service. Therefore at best you can read the PIDs corresponding to the various services, but you aren't going to be able to watch anything, as different utilities may come to terms with the datastreams in different ways. Most Linux utilities likely don't know anything of the DVB-H parsing needed for this service.
Note that I want to verify that this multiplex uses the more robust QAM16 along with 1/2 FEC rather than the QAM64 you have given, in order to permit best operation in diverse terrain, but I can't find my parse results from the datastream amongst my active disks. In any case, you can try this tuning option to see if you get a lock.
In order to receive these broadcasts, you will need to be a subscriber to this service -- I suggest that you get in touch with your nearest Swisscom to point you at the provider, though Sunrise or Orange or anyone else can probably point you to the provider of this service, who is unknown to me. I doubt you will achieve any Linux-based satisfaction here.
If this is not that to which you refer, then please re-formulate your question in a less ambiguous and more geographically-specific way, and sorry that I've wasted your time.
thanks,
barry bouwsma
Quoted 8 lines · g_remlin
02:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend-Budget/Hauppauge
WinTV-NOVA-T DVB card
Flags: bus master, medium devsel, latency 32, IRQ 17 Memory ate3001000(32-bit, non-prefetchable) [size=512] Kernel driver in use: budget dvb
Kernel modules: budget
Hi Barry, thanks for taking the time to reply (my previous more informative post was ignored).
This is the Terrestrial transmission standard being rolled out across the UK, I live in one of the first areas to be upgraded to the new standard. Since the change, my DVB-T PCI card will no longer tune (despite the signal level being indicated as OK in Kaffeine). I have confirmed the card does work correctly under Windows XP with the original card software, so it does not appear to be a hardware issue. I have tried numerous apps and various kernels, all without success. Any guidance as to what to try next, be it how to gather info for a bug report, or even a solution :), would be greatly appreciated.
Quoted 1 line · g_remlin
Hi Barry, thanks for taking the time to reply (my previous more informative
Happy to have helped, even though I didn't help.
Quoted 1 line
This is the Terrestrial transmission standard being rolled out across the UK,
Ah. I assumed `CH' referred to the country, and the FEC of 1/2 being that used for a robust yet low-bandwidth signal.
Actually, there are a couple steps to the DSO in the UK, with the introduction in less than two weeks of the DVB-T2 standard at a few places, to allow HD broadcasts with some 36 or so Mbit/sec.
This introduction will be taking place without any consumer equipment until next year, and cannot be received by existing hardware, as has been asked a few times on these lists. In the areas where this happens (apart from places like Crystal Palace) this is happening by converting one multiplex from DVB-T to -T2.
You probably are referring to the other part of DSO, which has meant the conversion from 2k to 8k transmission mode, and the use of 64QAM modulation.
Quoted 2 lines
I live in one of the first areas to be upgraded to the new standard. Since the change, my DVB-T PCI card will no longer tune (despite the signal level being
Once again I'll point out what in your Subject: is likely wrong, as these are not the values I know to be used in the UK:
``Subject : Re: CH???, Bandwidth 8MHz, Fec_Hi 1/2, Modulation QAM64, Mode 8K,
Guard 1/4, fails to tune\demux''
First off, the 1/2 FEC isn't used as that is used for a robust signal, as one would want from Handy-TV (DVB-H), and in the UK with its history of over-the-air broadcasting and rooftop aerials means that 2/3 and 3/4 are what I see listed (although the data I'm looking at appears to be pre-8k switchover).
Also, the guard interval would not be 1/4 as the UK makes use of MFN frequencies, and this appears reflected in the value of 1/32 listed in the old data.
You might try to re-scan with the above values corrected, if this would be a reason why you can't lock onto a signal.
thanks,
barry bouwsma
Hi Barry, thanks again, I understood that reply.
I got the Fec/Guard values I was using from the Windows XP app display, so am not surprised they are wrong :). Tried your suggestions, but no success. I have googled another user who has had success using a "switched over" transmitter similar to my local transmitter (http://www.dcglug.org.uk/archive/2009/09/msg00538.html), but is not using the same modules as me (saa7146, l64781). I have attached the tuning information from the Windows XP app in case you are interested. Not knowing what I am talking about - would the l64781 debug output help ?