MPC8567 - TEXT BASE boot rom question... Half the message was missing.. trying again..
last try, sorry about the multiple posts.
I must be doing something stupid, or I just don't understand how the 8567 boots from rom..., law entries, tables, etc...
Our board is using a MPC8567 with a 4 MEGByte boot rom flash (16 bit).... It has just 512MB of DDR2 memory(no ram on
the local bus). I can get u-boot to come up to the prompt ok but only
with a rom image(u-boot.bin) of 4MEG BYTE size and
the settings in the files, see below. I am using the BDI to write the 4meg image to the rom. I guess I don't understand TEXT_BASE very well.. and how it relates to the boot location.
What do I need to change to get a uboot image for the rom of reasonable size(say 512k instead of the 4meg)??? I have tried to change the value of TEXT_BASE to (xFFF8_0000) in the config.mk file(and other entries) but I must not be doing something else right.. Any suggestions/help would
be greatly appreciated!! Am I writng the u-boot.bin to the wrong
location in the flash when it is 512k?
Below is the relevant info from the files I think:
Thanks for your help in advance!
Bob
*********** config.mk file
TEXT_BASE = 0xffc00000
********** from the include/configs/sevis8567.h file
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses) */
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR
Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated
CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr
of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII usesCONFIG_SYS_IMMR */
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system
memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of
FLASH 8M */
#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH_BASE
/*Chip select 0 - Flash*/
#define CONFIG_SYS_BR0_PRELIM 0xfe001001
#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
I have OR's and BR's for the others also, but should not be relevant to the question so I didnt include.
#define CONFIG_SYS_LBC_LCRR 0x00030002 /* LB clock
ratio reg */
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_CPLD_BASE 0xD0000000 #define CONFIG_SYS_E1_IF_BASE 0xD1000000 #define CONFIG_SYS_DSP_BASE 0xD2000000 #define CONFIG_SYS_FPGA_BASE 0xD3000000
#define CONFIG_SYS_LBC_CPLD_BASE CONFIG_SYS_CPLD_BASE #define CONFIG_SYS_LBC_E1_IF_BASE CONFIG_SYS_E1_IF_BASE #define CONFIG_SYS_LBC_DSP_BASE CONFIG_SYS_DSP_BASE #define CONFIG_SYS_LBC_FPGA_BASE CONFIG_SYS_FPGA_BASE
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM
address */
#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial
data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END -CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for
Monitor */
#define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserved for
malloc */
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SECT_SIZE 0x2000 /* 256K(one sector) for env */ #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0xD0000) #define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OVERWRITE /* allow user to overwrite serial
and ethaddr */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
**************** from board/sevis/law.c
struct law_entry law_table[] = {
SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_DDR),
/* LBC window */
SET_LAW(CONFIG_SYS_LBC_CPLD_BASE, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
SET_LAW(CONFIG_SYS_LBC_E1_IF_BASE, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
SET_LAW(CONFIG_SYS_LBC_DSP_BASE, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
SET_LAW(CONFIG_SYS_LBC_FPGA_BASE, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
SET_LAW(CONFIG_SYS_LBC_FLASH_BASE, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
};int num_law_entries = ARRAY_SIZE(law_table);
****************** from board/sevis/tlb.c (the flash table entries I know must be wrong but the uboot comes up when these are set this way)
struct fsl_e_tlb_entry tlb_table[] = {
/* TLB 0 - for temp stack in cache */
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
/* TLB 1 Initializations */
/*
* TLBe 0: 16M Non-cacheable, guarded
* 0xff000000 16M FLASH (upper half)
* Out of reset this entry is only 4K.
*/
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000,
CONFIG_SYS_FLASH_BASE + 0x1000000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 0, BOOKE_PAGESZ_16M, 1),
/*
* TLBe 1: 16M Non-cacheable, guarded
* 0xfe000000 16M FLASH (lower half)
*/
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 1, BOOKE_PAGESZ_16M, 1),
/*
* TLBe 2: 64M Non-cacheable, guarded
* 0xe000_0000 1M CCSRBAR
* 0xe200_0000 8M PCI1 IO
* 0xe280_0000 8M PCIe IO
*/
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 2, BOOKE_PAGESZ_64M, 1),
/*
* TLB 3+4: 512M DDR, cache disabled (needed for memorytest)
* 0x00000000 512M DDR System memory
* Without SPD EEPROM configured DDR, this must be setup manually. */
SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE,CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 3, BOOKE_PAGESZ_256M, 1),
SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 4, BOOKE_PAGESZ_256M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 5, BOOKE_PAGESZ_16M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_E1_IF_BASE, CONFIG_SYS_E1_IF_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 6, BOOKE_PAGESZ_16M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_DSP_BASE, CONFIG_SYS_DSP_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 7, BOOKE_PAGESZ_16M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_FPGA_BASE, CONFIG_SYS_FPGA_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 8, BOOKE_PAGESZ_16M, 1),};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
Quoted 1 line · Bob Winslow
last try, sorry about the multiple posts.
Please don't post the same thing repeatedly. If there is anything new or changed in this version, it's very hard to spot. Just follow-up with only the new information.
-Scott
Dear Bob Winslow,
Quoted 1 line · In message <[email protected]> you wrote:
last try, sorry about the multiple posts.
Why the hell _do_ you post 3 times, especially when you are even aware of this?
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de War isn't a good life, but it's life. -- Kirk, "A Private Little War", stardate 4211.8