Skip to contentSkip to conversation

bio too big - in nested raid setup

DISCUSSION Ing. Daniel Rozsnyó 5 participants 9 messages Jan 24, 2010 – Jan 31, 2010

lore
Share & tools
lore
#0 lore raw

Hello,
I am having troubles with nested RAID - when one array is added to
the other, the "bio too big device md0" messages are appearing:

bio too big device md0 (144 > 8)
bio too big device md0 (248 > 8)
bio too big device md0 (32 > 8)

From internet searches I've found no solution or error like mine,
just a note about data corruption when this is happening.

Description:

My setup is the following - one 2TB and four 500GB drives. The goal
is to have a mirror of the 2TB drive to a linear array of the other four drives.

So.. the state without the error above is this:

# cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4]
md1 : active linear sdb1[0] sde1[3] sdd1[2] sdc1[1]
      1953535988 blocks super 1.1 0k rounding

md0 : active raid1 sda2[0]

      1953447680 blocks [2/1] [U_]
      bitmap: 233/233 pages [932KB], 4096KB chunk

unused devices: <none>

With these block request sizes:

# cat /sys/block/md{0,1}/queue/max_{,hw_}sectors_kb
127
127
127
127

Now, I add the four drive array to the mirror - and the system starts
showing the bio error at any significant disk activity.. (probably writes only). The reboot/shutdown process is full of these errors.

The step which messes up the system (ignore re-added, it happened the
very first time I've constructed the 4 drive array a hour ago):

# mdadm /dev/md0 --add /dev/md1
mdadm: re-added /dev/md1
# cat /sys/block/md{0,1}/queue/max_{,hw_}sectors_kb
4
4
127
127

The dmesg is just showing this:

md: bind<md1>
RAID1 conf printout:
--- wd:1 rd:2
disk 0, wo:0, o:1, dev:sda2
disk 1, wo:1, o:1, dev:md1
md: recovery of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
md: using 128k window, over a total of 1953447680 blocks.

And as soon as a write occures to the array:

bio too big device md0 (40 > 8)

The removal of md1 from md0 does not help the situation, I need to
reboot the machine.

The md0 array bears LVM and inside it a root / swap / portage /
distfiles and home logical volumes.

My system is:

# uname -a
Linux desktop 2.6.32-gentoo-r1 #2 SMP PREEMPT Sun Jan 24 12:06:13 CET 2010 i686 Intel(R) Xeon(R) CPU X3220 @ 2.40GHz GenuineIntel GNU/Linux

Thanks for any help,

Daniel

#1 lore raw

2010/1/24 "Ing. Daniel Rozsnyó" <[email protected]>:

Quoted 7 lines

Hello,
 I am having troubles with nested RAID - when one array is added to the other, the "bio too big device md0" messages are appearing:

bio too big device md0 (144 > 8)
bio too big device md0 (248 > 8)
bio too big device md0 (32 > 8)

I *think* this is the same bug that I hit years ago when mixing different disks and 'pvmove'

It's a design flaw in the DM/MD frameworks; see comment #3 from Milan Broz:
http://bugzilla.kernel.org/show_bug.cgi?id=9401#c3

Regards,
Marti

#2 lore raw
Quoted 9 lines · Marti Raudsepp

2010/1/24 "Ing. Daniel Rozsnyó" <[email protected]>:

Quoted 7 lines

Hello,
I am having troubles with nested RAID - when one array is added to the
other, the "bio too big device md0" messages are appearing:

bio too big device md0 (144 > 8)
bio too big device md0 (248 > 8)
bio too big device md0 (32 > 8)

Quoted 5 lines

I *think* this is the same bug that I hit years ago when mixing different disks and 'pvmove'

It's a design flaw in the DM/MD frameworks; see comment #3 from Milan Broz:
http://bugzilla.kernel.org/show_bug.cgi?id=9401#c3

Hm. I don't think it is the same problem, you are only adding device to md array... (adding cc: Neil, this seems to me like MD bug).

(original report for reference is here http://lkml.org/lkml/2010/1/24/60 )

Milan
--
[email protected]

#3 lore raw
Quoted 13 lines · On Mon, 25 Jan 2010 19:27:53 +0100 Milan Broz <[email protected]> wrote:
Quoted 12 lines · Marti Raudsepp

2010/1/24 "Ing. Daniel Rozsnyó" <[email protected]>:

Quoted 7 lines

Hello,
I am having troubles with nested RAID - when one array is added to the
other, the "bio too big device md0" messages are appearing:

bio too big device md0 (144 > 8)
bio too big device md0 (248 > 8)
bio too big device md0 (32 > 8)

I *think* this is the same bug that I hit years ago when mixing different disks and 'pvmove'

Quoted 7 lines
Quoted 2 lines

It's a design flaw in the DM/MD frameworks; see comment #3 from Milan Broz:
http://bugzilla.kernel.org/show_bug.cgi?id=9401#c3

Hm. I don't think it is the same problem, you are only adding device to md array... (adding cc: Neil, this seems to me like MD bug).

(original report for reference is here http://lkml.org/lkml/2010/1/24/60 )

No, I think it is the same problem.

When you have a stack of devices, the top level client needs to know the maximum restrictions imposed by lower level devices to ensure it doesn't violate them.
However there is no mechanism for a device to report that its restrictions have changed.
So when md0 gains a linear leg and so needs to reduce the max size for requests, there is no way to tell DM, so DM doesn't know. And as the filesystem only asks DM for restrictions, it never finds out about the new restrictions.

This should be fixed by having the filesystem not care about restrictions, and the lower levels just split requests as needed, but that just hasn't happened....

If you completely assemble md0 before activating the LVM stuff on top of it, this should work.

NeilBrown

#4 lore raw
Quoted 24 lines · Neil Brown
Quoted 12 lines · On Mon, 25 Jan 2010 19:27:53 +0100 Milan Broz <[email protected]> wrote:
Quoted 11 lines · Marti Raudsepp

2010/1/24 "Ing. Daniel Rozsnyó" <[email protected]>:

Quoted 7 lines

Hello,
I am having troubles with nested RAID - when one array is added to the
other, the "bio too big device md0" messages are appearing:

bio too big device md0 (144 > 8)
bio too big device md0 (248 > 8)
bio too big device md0 (32 > 8)

I *think* this is the same bug that I hit years ago when mixing different disks and 'pvmove'

Quoted 6 lines
Quoted 2 lines

It's a design flaw in the DM/MD frameworks; see comment #3 from Milan Broz:
http://bugzilla.kernel.org/show_bug.cgi?id=9401#c3

Hm. I don't think it is the same problem, you are only adding device to md array... (adding cc: Neil, this seems to me like MD bug).

(original report for reference is here http://lkml.org/lkml/2010/1/24/60 )

No, I think it is the same problem.

Quoted 9 lines

When you have a stack of devices, the top level client needs to know the maximum restrictions imposed by lower level devices to ensure it doesn't violate them.
However there is no mechanism for a device to report that its restrictions have changed.
So when md0 gains a linear leg and so needs to reduce the max size for requests, there is no way to tell DM, so DM doesn't know. And as the filesystem only asks DM for restrictions, it never finds out about the new restrictions.

Neil, why does it even reduce its block size? I've tried with both "linear" and "raid0" (as they are the only way to get 2T from 4x500G) and both behave the same (sda has 512, md0 127, linear 127 and raid0 has 512 kb block size).

I do not see the mechanism how 512:127 or 512:512 leads to 4 kb limit

Is it because:
- of rebuilding the array?
- of non-multiplicative max block size
- of non-multiplicative total device size
- of nesting?
- of some other fallback to 1 page?

I ask because I can not believe that a pre-assembled nested stack would result in 4kb max limit. But I haven't tried yet (e.g. from a live cd).

The block device should not do this kind of "magic", unless the higher layers support it. Which one has proper support then?
- standard partition table?
- LVM?
- filesystem drivers?

Quoted 8 lines

This should be fixed by having the filesystem not care about restrictions, and the lower levels just split requests as needed, but that just hasn't happened....

If you completely assemble md0 before activating the LVM stuff on top of it, this should work.

NeilBrown

#5 lore raw
Quoted 35 lines · On Thu, 28 Jan 2010 10:24:43 +0100 "Ing. Daniel Rozsnyó" <[email protected]>…
Quoted 24 lines · Neil Brown
Quoted 12 lines · On Mon, 25 Jan 2010 19:27:53 +0100 Milan Broz <[email protected]> wrote:
Quoted 11 lines · Marti Raudsepp

2010/1/24 "Ing. Daniel Rozsnyó" <[email protected]>:

Quoted 7 lines

Hello,
I am having troubles with nested RAID - when one array is added to the
other, the "bio too big device md0" messages are appearing:

bio too big device md0 (144 > 8)
bio too big device md0 (248 > 8)
bio too big device md0 (32 > 8)

I *think* this is the same bug that I hit years ago when mixing different disks and 'pvmove'

Quoted 6 lines
Quoted 2 lines

It's a design flaw in the DM/MD frameworks; see comment #3 from Milan Broz:
http://bugzilla.kernel.org/show_bug.cgi?id=9401#c3

Hm. I don't think it is the same problem, you are only adding device to md array... (adding cc: Neil, this seems to me like MD bug).

(original report for reference is here http://lkml.org/lkml/2010/1/24/60 )

No, I think it is the same problem.

Quoted 9 lines

When you have a stack of devices, the top level client needs to know the maximum restrictions imposed by lower level devices to ensure it doesn't violate them.
However there is no mechanism for a device to report that its restrictions have changed.
So when md0 gains a linear leg and so needs to reduce the max size for requests, there is no way to tell DM, so DM doesn't know. And as the filesystem only asks DM for restrictions, it never finds out about the new restrictions.

Quoted 6 lines

Neil, why does it even reduce its block size? I've tried with both "linear" and "raid0" (as they are the only way to get 2T from 4x500G) and both behave the same (sda has 512, md0 127, linear 127 and raid0 has 512 kb block size).

I do not see the mechanism how 512:127 or 512:512 leads to 4 kb limit

Both raid0 and linear register a 'bvec_mergeable' function (or whatever it is called today).
This allows for the fact that these devices have restrictions that cannot be expressed simply with request sizes. In particular they only handle requests that don't cross a chunk boundary.

As raid1 never calls the bvec_mergeable function of it's components (it would be very hard to get that to work reliably, maybe impossible), it treats any device with a bvec_mergeable function as though the max_sectors were one page. This is because the interface guarantees that a one page request will always be handled.

Quoted 7 lines

Is it because:
- of rebuilding the array?
- of non-multiplicative max block size
- of non-multiplicative total device size
- of nesting?
- of some other fallback to 1 page?

The last I guess.

Quoted 3 lines

I ask because I can not believe that a pre-assembled nested stack would result in 4kb max limit. But I haven't tried yet (e.g. from a live cd).

When people say "I can not believe" I always chuckle to myself. You just aren't trying hard enough. There is adequate evidence that people can believe whatever they want to believe :-)

Quoted 7 lines

The block device should not do this kind of "magic", unless the higher layers support it. Which one has proper support then?
- standard partition table?
- LVM?
- filesystem drivers?

I don't understand this question, sorry.

Yes, there is definitely something broken here. Unfortunately fixing it is non-trivial.

NeilBrown

#6 lore raw
Quoted 7 lines · Neil Brown

Both raid0 and linear register a 'bvec_mergeable' function (or whatever it is called today).
This allows for the fact that these devices have restrictions that cannot be expressed simply with request sizes. In particular they only handle requests that don't cross a chunk boundary.

Quoted 6 lines

As raid1 never calls the bvec_mergeable function of it's components (it would be very hard to get that to work reliably, maybe impossible), it treats any device with a bvec_mergeable function as though the max_sectors were one page. This is because the interface guarantees that a one page request will always be handled.

I'm also guilty of doing some mirror work, in exofs, over osd objects.

I was thinking about that reliability problem with mirrors, also related to that infamous problem of coping the mirrored buffers so they do not change while writing at the page cache level.

So what if we don't fight it? what if we just keep a journal of the mirror unbalanced state and do not page_uptodate until the mirror is finally balanced. Only then pages can be dropped from the cache, and journal cleared.

(Balanced-mirror-page is when a page has participated in an IO to all devices
without being marked dirty from the get-go to the completion of IO)

I think Trond's last work with adding that un_updated-but-committed state to pages can facilitate in doing that, though I do understand that it is a major conceptual change to the the VFS-BLOCKS relationship in letting the block devices participate in the pages state machine (And md keeping a journal). Sigh

??
Boaz

#7 lore raw
Quoted 15 lines · On Thu, 28 Jan 2010 14:07:31 +0200 Boaz Harrosh <[email protected]> wrote:
Quoted 7 lines · Neil Brown

Both raid0 and linear register a 'bvec_mergeable' function (or whatever it is called today).
This allows for the fact that these devices have restrictions that cannot be expressed simply with request sizes. In particular they only handle requests that don't cross a chunk boundary.

Quoted 6 lines

As raid1 never calls the bvec_mergeable function of it's components (it would be very hard to get that to work reliably, maybe impossible), it treats any device with a bvec_mergeable function as though the max_sectors were one page. This is because the interface guarantees that a one page request will always be handled.

Quoted 5 lines

I'm also guilty of doing some mirror work, in exofs, over osd objects.

I was thinking about that reliability problem with mirrors, also related to that infamous problem of coping the mirrored buffers so they do not change while writing at the page cache level.

So this is a totally new topic, right?

Quoted 4 lines

So what if we don't fight it? what if we just keep a journal of the mirror unbalanced state and do not page_uptodate until the mirror is finally balanced. Only then pages can be dropped from the cache, and journal cleared.

I cannot see what you are suggesting, but it seems like a layering violation. The block device level cannot see anything about whether the page is up to date or not. The page it has may not even be in the page cache.

The only thing that the block device can do is make a copy of the page and write that out twice.

If we could have a flag which the filesystem can send to say "I promise not to change this page until the IO completes", then that copy could be optimised away in lots of common cases.

Quoted 4 lines

(Balanced-mirror-page is when a page has participated in an IO to all devices
without being marked dirty from the get-go to the completion of IO)

Block device cannot see the 'dirty' flag.

Quoted 7 lines

I think Trond's last work with adding that un_updated-but-committed state to pages can facilitate in doing that, though I do understand that it is a major conceptual change to the the VFS-BLOCKS relationship in letting the block devices participate in the pages state machine (And md keeping a journal). Sigh

??
Boaz

NeilBrown

#8 lore raw
Quoted 5 lines · Neil Brown
Quoted 2 lines · On Thu, 28 Jan 2010 14:07:31 +0200 Boaz Harrosh <[email protected]> wrote:
Quoted 1 line · Neil Brown

I'm totally theoretical on this. So feel free to ignore me, if it gets boring.

Quoted 13 lines
Quoted 13 lines
Quoted 12 lines

Both raid0 and linear register a 'bvec_mergeable' function (or whatever it is called today).
This allows for the fact that these devices have restrictions that cannot be expressed simply with request sizes. In particular they only handle requests that don't cross a chunk boundary.

As raid1 never calls the bvec_mergeable function of it's components (it would be very hard to get that to work reliably, maybe impossible), it treats any device with a bvec_mergeable function as though the max_sectors were one page. This is because the interface guarantees that a one page request will always be handled.

Quoted 8 lines
Quoted 5 lines

I'm also guilty of doing some mirror work, in exofs, over osd objects.

I was thinking about that reliability problem with mirrors, also related to that infamous problem of coping the mirrored buffers so they do not change while writing at the page cache level.

So this is a totally new topic, right?

Not new, I'm talking about that (no) guaranty of page not changing while in flight, as you mention below. Which is why we need to copy the to-be-mirrored page.

Quoted 9 lines
Quoted 4 lines

So what if we don't fight it? what if we just keep a journal of the mirror unbalanced state and do not page_uptodate until the mirror is finally balanced. Only then pages can be dropped from the cache, and journal cleared.

I cannot see what you are suggesting, but it seems like a layering violation. The block device level cannot see anything about whether the page is up to date or not. The page it has may not even be in the page cache.

It is certainly a layering violation today, but theoretically speaking ,it does not have to be. An abstract API can be made so block devices notify when page's IO is done, at this point VFS can decide if it must resubmit do to page changing while IO or the IO is actually valid at this point.

Quoted 3 lines

The only thing that the block device can do is make a copy of the page and write that out twice.

That is the copy I was referring to.

Quoted 4 lines

If we could have a flag which the filesystem can send to say "I promise not to change this page until the IO completes", then that copy could be optimised away in lots of common cases.

What I meant is: What if we only have that knowledge at end of IO, So we can decide at that point if the page is up-to-date and is allowed to be evicted from cache. It's the same as if we have a crash/power-failure while IO, surely the mirrors are not balanced, and each device's file content cannot be determained some of the last written buffer is old, some new, and some undefined. That is the roll of the file-system to keep a journal and decide what data can be guaranteed and what data must be reverted to a last known good state. Now what I'm wondering is what if we prolong this window to until we know the mirrors match. The window for disaster is wider, but should never matter in normal use. Most setups could tolerate the bad statistics, and could use the extra bandwidth.

Quoted 8 lines
Quoted 5 lines

(Balanced-mirror-page is when a page has participated in an IO to all devices
without being marked dirty from the get-go to the completion of IO)

Block device cannot see the 'dirty' flag.

Right, but is there some additional information a block device should communicate to the FS so it can make a decision?

Quoted 10 lines
Quoted 8 lines

I think Trond's last work with adding that un_updated-but-committed state to pages can facilitate in doing that, though I do understand that it is a major conceptual change to the the VFS-BLOCKS relationship in letting the block devices participate in the pages state machine (And md keeping a journal). Sigh

??
Boaz

NeilBrown

Thanks
Boaz