AT91: Update otc570 board to new SoC access
PATCH 1/1 AT91: Update otc570 board to new SoC access
* convert otc570 board to use c stucture SoC access
* change gpio access to at91_gpio syntax
---
This patch requires Jens Scharsigs new SoC access patchset.
http://lists.denx.de/pipermail/u-boot/2010-February/067424.html
http://lists.denx.de/pipermail/u-boot/2010-February/067425.html
http://lists.denx.de/pipermail/u-boot/2010-February/067426.html
http://lists.denx.de/pipermail/u-boot/2010-February/067427.html
http://lists.denx.de/pipermail/u-boot/2010-February/067428.html
http://lists.denx.de/pipermail/u-boot/2010-February/067429.html
http://lists.denx.de/pipermail/u-boot/2010-February/067430.html
http://lists.denx.de/pipermail/u-boot/2010-February/067431.html
http://lists.denx.de/pipermail/u-boot/2010-February/067432.html
Apart from a tiny change, I give them an ACK. See
http://lists.denx.de/pipermail/u-boot/2010-February/067674.html
and
http://lists.denx.de/pipermail/u-boot/2010-February/067680.html
board/esd/otc570/otc570.c | 180 ++++++++++++++++++++++++--------------------- include/configs/otc570.h | 25 +++--- 2 files changed, 107 insertions(+), 98 deletions(-)
board/esd/otc570/otc570.c +95 -85
@@ -28,13 +28,13 @@#include <common.h> #include <asm/arch/at91sam9263.h> -#include <asm/arch/at91sam9_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_matrix.h> +#include <asm/arch/at91_pio.h> #include <asm/arch/clk.h> -#include <asm/arch/gpio.h> #include <asm/arch/hardware.h> #include <asm/arch/io.h> #include <atmel_lcdc.h>
@@ -58,10 +58,10 @@ int get_hw_rev(void)if (hw_rev >=0 )return hw_rev; - hw_rev =at91_get_gpio_value (AT91_PIN_PB19 ); - hw_rev |=at91_get_gpio_value (AT91_PIN_PB20 ) <<1 ; - hw_rev |=at91_get_gpio_value (AT91_PIN_PB21 ) <<2 ; - hw_rev |=at91_get_gpio_value (AT91_PIN_PB22 ) <<3 ; + hw_rev =at91_get_pio_value (AT91_PIO_PORTB ,19 ); + hw_rev |=at91_get_pio_value (AT91_PIO_PORTB ,20 ) <<1 ; + hw_rev |=at91_get_pio_value (AT91_PIO_PORTB ,21 ) <<2 ; + hw_rev |=at91_get_pio_value (AT91_PIO_PORTB ,22 ) <<3 ;if (hw_rev ==15 ) hw_rev =0 ;
@@ -73,40 +73,44 @@ int get_hw_rev(void)static void otc570_nand_hw_init (void ) {unsigned long csa; +at91_smc_t *smc = (at91_smc_t *)AT91_SMC0_BASE ; +at91_matrix_t *matrix = (at91_matrix_t *)AT91_MATRIX_BASE ;/* Enable CS3 */ - csa =at91_sys_read (AT91_MATRIX_EBI0CSA ); -at91_sys_write (AT91_MATRIX_EBI0CSA , - csa |AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA ); + csa =readl (&matrix->csa[0 ]) |AT91_MATRIX_CSA_EBI_CS3A ; +writel (csa, &matrix->csa[0 ]);/* Configure SMC CS3 for NAND/SmartMedia */ -at91_sys_write (AT91_SMC_SETUP (3 ), -AT91_SMC_NWESETUP_ (1 ) |AT91_SMC_NCS_WRSETUP_ (0 ) | -AT91_SMC_NRDSETUP_ (1 ) |AT91_SMC_NCS_RDSETUP_ (0 )); -at91_sys_write (AT91_SMC_PULSE (3 ), -AT91_SMC_NWEPULSE_ (3 ) |AT91_SMC_NCS_WRPULSE_ (3 ) | -AT91_SMC_NRDPULSE_ (3 ) |AT91_SMC_NCS_RDPULSE_ (3 )); -at91_sys_write (AT91_SMC_CYCLE (3 ), -AT91_SMC_NWECYCLE_ (5 ) |AT91_SMC_NRDCYCLE_ (5 )); -at91_sys_write (AT91_SMC_MODE (3 ), -AT91_SMC_READMODE |AT91_SMC_WRITEMODE | -AT91_SMC_EXNWMODE_DISABLE | -AT91_SMC_DBW_8 | -AT91_SMC_TDF_ (2 )); +writel (AT91_SMC_SETUP_NWE (1 ) |AT91_SMC_SETUP_NCS_WR (0 ) | +AT91_SMC_SETUP_NRD (1 ) |AT91_SMC_SETUP_NCS_RD (0 ), + &smc->cs[3 ].setup); + +writel (AT91_SMC_PULSE_NWE (3 ) |AT91_SMC_PULSE_NCS_WR (3 ) | +AT91_SMC_PULSE_NRD (3 ) |AT91_SMC_PULSE_NCS_RD (3 ), + &smc->cs[3 ].pulse); + +writel (AT91_SMC_CYCLE_NWE (5 ) |AT91_SMC_CYCLE_NRD (5 ), + &smc->cs[3 ].cycle); +writel (AT91_SMC_MODE_RM_NRD |AT91_SMC_MODE_WM_NWE | +AT91_SMC_MODE_EXNW_DISABLE | +AT91_SMC_MODE_DBW_8 | +AT91_SMC_MODE_TDF_CYCLE (2 ), + &smc->cs[3 ].mode);/* Configure RDY/BSY */ -at91_set_gpio_input (CONFIG_SYS_NAND_READY_PIN ,1 ); +at91_set_pio_input (CONFIG_SYS_NAND_READY_PIN ,1 );/* Enable NandFlash */ -at91_set_gpio_output (CONFIG_SYS_NAND_ENABLE_PIN ,1 ); +at91_set_pio_output (CONFIG_SYS_NAND_ENABLE_PIN ,1 ); }#endif /* CONFIG_CMD_NAND */ #ifdef CONFIG_MACB static void otc570_macb_hw_init (void ) { +at91_pmc_t *pmc = (at91_pmc_t *)AT91_PMC_BASE ;/* Enable clock */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_EMAC ); +writel (1 <<AT91SAM9263_ID_EMAC , &pmc->pcer);at91_macb_hw_init (); }#endif
@@ -119,26 +123,27 @@ static void otc570_macb_hw_init(void)*/ static void otc570_ethercat_hw_init (void ) { +at91_smc_t *smc1 = (at91_smc_t *)AT91_SMC1_BASE ; +/* Configure SMC EBI1_CS0 for EtherCAT */ -at91_sys_write (AT91_SMC1_SETUP (0 ), -AT91_SMC_NWESETUP_ (0 ) |AT91_SMC_NCS_WRSETUP_ (0 ) | -AT91_SMC_NRDSETUP_ (0 ) |AT91_SMC_NCS_RDSETUP_ (0 )); -at91_sys_write (AT91_SMC1_PULSE (0 ), -AT91_SMC_NWEPULSE_ (4 ) |AT91_SMC_NCS_WRPULSE_ (9 ) | -AT91_SMC_NRDPULSE_ (5 ) |AT91_SMC_NCS_RDPULSE_ (9 )); -at91_sys_write (AT91_SMC1_CYCLE (0 ), -AT91_SMC_NWECYCLE_ (10 ) |AT91_SMC_NRDCYCLE_ (6 )); +writel (AT91_SMC_SETUP_NWE (0 ) |AT91_SMC_SETUP_NCS_WR (0 ) | +AT91_SMC_SETUP_NRD (0 ) |AT91_SMC_SETUP_NCS_RD (0 ), + &smc1->cs[0 ].setup); +writel (AT91_SMC_PULSE_NWE (4 ) |AT91_SMC_PULSE_NCS_WR (9 ) | +AT91_SMC_PULSE_NRD (5 ) |AT91_SMC_PULSE_NCS_RD (9 ), + &smc1->cs[0 ].pulse); +writel (AT91_SMC_CYCLE_NWE (10 ) |AT91_SMC_CYCLE_NRD (6 ), + &smc1->cs[0 ].cycle);/* * Configure behavior at external wait signal, byte-select mode, 16 bit * data bus width, none data float wait states and TDF optimization */ -at91_sys_write (AT91_SMC1_MODE (0 ), -AT91_SMC_READMODE |AT91_SMC_EXNWMODE_READY | -AT91_SMC_BAT_SELECT |AT91_SMC_DBW_16 |AT91_SMC_TDF_ (0 ) | -AT91_SMC_TDFMODE ); +writel (AT91_SMC_MODE_RM_NRD |AT91_SMC_MODE_EXNW_READY | +AT91_SMC_MODE_DBW_16 |AT91_SMC_MODE_TDF_CYCLE (0 ) | +AT91_SMC_MODE_TDF , &smc1->cs[0 ].mode);/* Configure RDY/BSY */ -at91_set_B_periph (AT91_PIN_PE20 ,0 );/* EBI1_NWAIT */ +at91_set_b_periph (AT91_PIO_PORTE ,20 ,0 );/* EBI1_NWAIT */ }#ifdef CONFIG_LCD
@@ -164,43 +169,44 @@ vidinfo_t panel_info = {void lcd_enable (void ) { -at91_set_gpio_value (AT91_PIN_PA30 ,0 );/* power up */ +at91_set_pio_value (AT91_PIO_PORTA ,30 ,0 );/* power up */ }void lcd_disable (void ) { -at91_set_gpio_value (AT91_PIN_PA30 ,1 );/* power down */ +at91_set_pio_value (AT91_PIO_PORTA ,30 ,1 );/* power down */ }static void otc570_lcd_hw_init (void ) { -at91_set_A_periph (AT91_PIN_PC0 ,0 );/* LCDVSYNC */ -at91_set_A_periph (AT91_PIN_PC1 ,0 );/* LCDHSYNC */ -at91_set_A_periph (AT91_PIN_PC2 ,0 );/* LCDDOTCK */ -at91_set_A_periph (AT91_PIN_PC3 ,0 );/* LCDDEN */ -at91_set_B_periph (AT91_PIN_PB9 ,0 );/* LCDCC */ -at91_set_A_periph (AT91_PIN_PC6 ,0 );/* LCDD2 */ -at91_set_A_periph (AT91_PIN_PC7 ,0 );/* LCDD3 */ -at91_set_A_periph (AT91_PIN_PC8 ,0 );/* LCDD4 */ -at91_set_A_periph (AT91_PIN_PC9 ,0 );/* LCDD5 */ -at91_set_A_periph (AT91_PIN_PC10 ,0 );/* LCDD6 */ -at91_set_A_periph (AT91_PIN_PC11 ,0 );/* LCDD7 */ -at91_set_A_periph (AT91_PIN_PC14 ,0 );/* LCDD10 */ -at91_set_A_periph (AT91_PIN_PC15 ,0 );/* LCDD11 */ -at91_set_A_periph (AT91_PIN_PC16 ,0 );/* LCDD12 */ -at91_set_B_periph (AT91_PIN_PC12 ,0 );/* LCDD13 */ -at91_set_A_periph (AT91_PIN_PC18 ,0 );/* LCDD14 */ -at91_set_A_periph (AT91_PIN_PC19 ,0 );/* LCDD15 */ -at91_set_A_periph (AT91_PIN_PC22 ,0 );/* LCDD18 */ -at91_set_A_periph (AT91_PIN_PC23 ,0 );/* LCDD19 */ -at91_set_A_periph (AT91_PIN_PC24 ,0 );/* LCDD20 */ -at91_set_B_periph (AT91_PIN_PC17 ,0 );/* LCDD21 */ -at91_set_A_periph (AT91_PIN_PC26 ,0 );/* LCDD22 */ -at91_set_A_periph (AT91_PIN_PC27 ,0 );/* LCDD23 */ -at91_set_gpio_output (AT91_PIN_PA30 ,1 );/* PCI */ - -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_LCDC ); - +at91_pmc_t *pmc = (at91_pmc_t *)AT91_PMC_BASE ; + +at91_set_a_periph (AT91_PIO_PORTC ,0 ,0 );/* LCDVSYNC */ +at91_set_a_periph (AT91_PIO_PORTC ,1 ,0 );/* LCDHSYNC */ +at91_set_a_periph (AT91_PIO_PORTC ,2 ,0 );/* LCDDOTCK */ +at91_set_a_periph (AT91_PIO_PORTC ,3 ,0 );/* LCDDEN */ +at91_set_b_periph (AT91_PIO_PORTB ,9 ,0 );/* LCDCC */ +at91_set_a_periph (AT91_PIO_PORTC ,6 ,0 );/* LCDD2 */ +at91_set_a_periph (AT91_PIO_PORTC ,7 ,0 );/* LCDD3 */ +at91_set_a_periph (AT91_PIO_PORTC ,8 ,0 );/* LCDD4 */ +at91_set_a_periph (AT91_PIO_PORTC ,9 ,0 );/* LCDD5 */ +at91_set_a_periph (AT91_PIO_PORTC ,10 ,0 );/* LCDD6 */ +at91_set_a_periph (AT91_PIO_PORTC ,11 ,0 );/* LCDD7 */ +at91_set_a_periph (AT91_PIO_PORTC ,14 ,0 );/* LCDD10 */ +at91_set_a_periph (AT91_PIO_PORTC ,15 ,0 );/* LCDD11 */ +at91_set_a_periph (AT91_PIO_PORTC ,16 ,0 );/* LCDD12 */ +at91_set_b_periph (AT91_PIO_PORTC ,12 ,0 );/* LCDD13 */ +at91_set_a_periph (AT91_PIO_PORTC ,18 ,0 );/* LCDD14 */ +at91_set_a_periph (AT91_PIO_PORTC ,19 ,0 );/* LCDD15 */ +at91_set_a_periph (AT91_PIO_PORTC ,22 ,0 );/* LCDD18 */ +at91_set_a_periph (AT91_PIO_PORTC ,23 ,0 );/* LCDD19 */ +at91_set_a_periph (AT91_PIO_PORTC ,24 ,0 );/* LCDD20 */ +at91_set_b_periph (AT91_PIO_PORTC ,17 ,0 );/* LCDD21 */ +at91_set_a_periph (AT91_PIO_PORTC ,26 ,0 );/* LCDD22 */ +at91_set_a_periph (AT91_PIO_PORTC ,27 ,0 );/* LCDD23 */ +at91_set_pio_output (AT91_PIO_PORTA ,30 ,1 );/* PCI */ + +writel (1 <<AT91SAM9263_ID_LCDC , &pmc->pcer); gd->fb_base =CONFIG_OTC570_LCD_BASE ; }
@@ -242,7 +248,7 @@ int board_eth_init(bd_t *bis) {int rc =0 ;#ifdef CONFIG_MACB - rc =macb_eth_initialize (0 , (void *)AT91SAM9263_BASE_EMAC ,0x00 ); + rc =macb_eth_initialize (0 , (void *)AT91_EMAC_BASE ,0x00 );#endif return rc; }
@@ -290,32 +296,33 @@ u32 get_board_rev(void)#ifdef CONFIG_MISC_INIT_R int misc_init_r (void ) { -char str[64 ]; +char str[64 ]; +at91_pmc_t *pmc = (at91_pmc_t *)AT91_PMC_BASE ; -at91_set_gpio_output (AT91_PIN_PA29 ,1 ); -at91_set_A_periph (AT91_PIN_PA26 ,1 );/* TXD0 */ -at91_set_A_periph (AT91_PIN_PA27 ,0 );/* RXD0 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_US0 ); +at91_set_pio_output (AT91_PIO_PORTA ,29 ,1 ); +at91_set_a_periph (AT91_PIO_PORTA ,26 ,1 );/* TXD0 */ +at91_set_a_periph (AT91_PIO_PORTA ,27 ,0 );/* RXD0 */ +writel (1 <<AT91SAM9263_ID_US0 , &pmc->pcer);/* Set USART_MODE = 1 (RS485) */ -at91_sys_write ((0xFFF8C004 -AT91_BASE_SYS ),1 ); +writel (1 ,0xFFF8C004 );printf ("USART0: " );if (getenv_r ("usart0" , str,sizeof (str)) ==-1 ) {printf ("No entry - assuming 1-wire\n" );/* CTS pin, works as mode select pin (0 = 1-wire; 1 = RS485) */ -at91_set_gpio_output (AT91_PIN_PA29 ,0 ); +at91_set_pio_output (AT91_PIO_PORTA ,29 ,0 ); }else {if (strcmp (str,"1-wire" ) ==0 ) {printf ("%s\n" , str); -at91_set_gpio_output (AT91_PIN_PA29 ,0 ); +at91_set_pio_output (AT91_PIO_PORTA ,29 ,0 ); }else if (strcmp (str,"rs485" ) ==0 ) {printf ("%s\n" , str); -at91_set_gpio_output (AT91_PIN_PA29 ,1 ); +at91_set_pio_output (AT91_PIO_PORTA ,29 ,1 ); }else {printf ("Wrong entry - assuming 1-wire " );printf ("(valid values are '1-wire' or 'rs485')\n" ); -at91_set_gpio_output (AT91_PIN_PA29 ,0 ); +at91_set_pio_output (AT91_PIO_PORTA ,29 ,0 ); } }printf ("Display memory address: 0x%08lX\n" , gd->fb_base);
@@ -326,14 +333,17 @@ int misc_init_r(void)int board_init (void ) { +at91_pmc_t *pmc = (at91_pmc_t *)AT91_PMC_BASE ; +/* Peripheral Clock Enable Register */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_PIOA | -1 <<AT91SAM9263_ID_PIOB | -1 <<AT91SAM9263_ID_PIOCDE | -1 <<AT91SAM9263_ID_TWI | -1 <<AT91SAM9263_ID_SPI0 | -1 <<AT91SAM9263_ID_LCDC | -1 <<AT91SAM9263_ID_UHP ); +writel (1 <<AT91SAM9263_ID_PIOA | +1 <<AT91SAM9263_ID_PIOB | +1 <<AT91SAM9263_ID_PIOCDE | +1 <<AT91SAM9263_ID_TWI | +1 <<AT91SAM9263_ID_SPI0 | +1 <<AT91SAM9263_ID_LCDC | +1 <<AT91SAM9263_ID_UHP , + &pmc->pcer);/* arch number of OTC570-Board */ gd->bd->bi_arch_number =MACH_TYPE_OTC570 ;
include/configs/otc570.h +12 -13
@@ -55,6 +55,7 @@/* * Hardware drivers */ +#define CONFIG_AT91_GPIO 1/* Console output */ #define CONFIG_ATMEL_USART 1
@@ -96,24 +97,22 @@#ifdef CONFIG_SOFT_I2C #define CONFIG_I2C_CMD_TREE 1#define CONFIG_I2C_MULTI_BUS 1 -/* Enable peripheral clock and configure data and clock pins for pio */ +/* Configure data and clock pins for pio */ #define I2C_INIT { \ - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_PIOB | \ - 1 << AT91SAM9263_ID_PIOCDE); \ - at91_set_gpio_output(AT91_PIN_PB4, 0); \ - at91_set_gpio_output(AT91_PIN_PB5, 0); \ + at91_set_pio_output(AT91_PIO_PORTB, 4, 0); \ + at91_set_pio_output(AT91_PIO_PORTB, 5, 0); \ }/* Configure data pin as output */ -#define I2C_ACTIVE at91_set_gpio_output(AT91_PIN_PB4, 0) +#define I2C_ACTIVE at91_set_pio_output(AT91_PIO_PORTB, 4, 0)/* Configure data pin as input */ -#define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PB4, 0) +#define I2C_TRISTATE at91_set_pio_input(AT91_PIO_PORTB, 4, 0)/* Read data pin */ -#define I2C_READ at91_get_gpio_value(AT91_PIN_PB4) +#define I2C_READ at91_get_pio_value(AT91_PIO_PORTB, 4)/* Set data pin */ -#define I2C_SDA (bit) at91_set_gpio_value(AT91_PIN_PB4, bit) +#define I2C_SDA (bit) at91_set_pio_value(AT91_PIO_PORTB, 4, bit)/* Set clock pin */ -#define I2C_SCL (bit) at91_set_gpio_value(AT91_PIN_PB5, bit) -#define I2C_DELAY udelay(2)/* 1/4 I2C clock duration */ +#define I2C_SCL (bit) at91_set_pio_value(AT91_PIO_PORTB, 5, bit) +#define I2C_DELAY udelay(2)/* 1/4 I2C clock duration */ #endif /* CONFIG_SOFT_I2C */ #define CONFIG_BOOTDELAY 3
@@ -173,8 +172,8 @@#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)/* our CLE is AD22 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PA22 +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif
Signature · 1 line
1.5.3
PATCH 1/1 AT91: Update otc570 board to new SoC access
Hello Tom
Quoted 4 lines · Daniel Gorsulowski
* convert otc570 board to use c stucture SoC access
* change gpio access toat91_gpiosyntaxSigned-off-by Daniel Gorsulowski <[email protected]>
Quoted 12 lines
---
This patch requires Jens Scharsigs new SoC access patchset.
http://lists.denx.de/pipermail/u-boot/2010-February/067424.html
http://lists.denx.de/pipermail/u-boot/2010-February/067425.html
http://lists.denx.de/pipermail/u-boot/2010-February/067426.html
http://lists.denx.de/pipermail/u-boot/2010-February/067427.html
http://lists.denx.de/pipermail/u-boot/2010-February/067428.html
http://lists.denx.de/pipermail/u-boot/2010-February/067429.html
http://lists.denx.de/pipermail/u-boot/2010-February/067430.html
http://lists.denx.de/pipermail/u-boot/2010-February/067431.html
http://lists.denx.de/pipermail/u-boot/2010-February/067432.html
...
I recognized, you didn't apply this patch yet. Is there any reason, or did you simply slip this patch?
Btw. I'm also missing this patch:
http://lists.denx.de/pipermail/u-boot/2010-February/067779.html
Best regards,
Daniel Gorsulowski
PATCH 1/1 AT91: Update otc570 board to new SoC access
Quoted 19 lines · Daniel Gorsulowski
Hello Tom
Quoted 4 lines · Daniel Gorsulowski
* convert otc570 board to use c stucture SoC access
* change gpio access toat91_gpiosyntaxSigned-off-by Daniel Gorsulowski <[email protected]>Quoted 12 lines
---
This patch requires Jens Scharsigs new SoC access patchset.
http://lists.denx.de/pipermail/u-boot/2010-February/067424.html
http://lists.denx.de/pipermail/u-boot/2010-February/067425.html
http://lists.denx.de/pipermail/u-boot/2010-February/067426.html
http://lists.denx.de/pipermail/u-boot/2010-February/067427.html
http://lists.denx.de/pipermail/u-boot/2010-February/067428.html
http://lists.denx.de/pipermail/u-boot/2010-February/067429.html
http://lists.denx.de/pipermail/u-boot/2010-February/067430.html
http://lists.denx.de/pipermail/u-boot/2010-February/067431.html
http://lists.denx.de/pipermail/u-boot/2010-February/067432.html
Quoted 8 lines
...
I recognized, you didn't apply this patch yet. Is there any reason, or did you simply slip this patch?
Btw. I'm also missing this patch:
http://lists.denx.de/pipermail/u-boot/2010-February/067779.html
Yes.
This was slipped.
I spent some time trying to work out which patches needed to be applied to remove the build errors I was seeing with otc but was unable to.
Please send me the list of patches and oder of application.
Tom
Quoted 2 lines
Best regards,
Daniel Gorsulowski
PATCH 1/1 AT91: Update otc570 board to new SoC access
Quoted 36 lines · Tom
Quoted 19 lines · Daniel Gorsulowski
Hello Tom
Quoted 4 lines · Daniel Gorsulowski
* convert otc570 board to use c stucture SoC access
* change gpio access toat91_gpiosyntaxSigned-off-by Daniel Gorsulowski <[email protected]>Quoted 12 lines
---
This patch requires Jens Scharsigs new SoC access patchset.
http://lists.denx.de/pipermail/u-boot/2010-February/067424.html
http://lists.denx.de/pipermail/u-boot/2010-February/067425.html
http://lists.denx.de/pipermail/u-boot/2010-February/067426.html
http://lists.denx.de/pipermail/u-boot/2010-February/067427.html
http://lists.denx.de/pipermail/u-boot/2010-February/067428.html
http://lists.denx.de/pipermail/u-boot/2010-February/067429.html
http://lists.denx.de/pipermail/u-boot/2010-February/067430.html
http://lists.denx.de/pipermail/u-boot/2010-February/067431.html
http://lists.denx.de/pipermail/u-boot/2010-February/067432.htmlQuoted 9 lines
...
I recognized, you didn't apply this patch yet. Is there any reason, or did you
simply slip this patch?Btw. I'm also missing this patch:
http://lists.denx.de/pipermail/u-boot/2010-February/067779.htmlYes.
This was slipped.
I spent some time trying to work out which patches needed to be applied to remove the build errors I was seeing with otc but was unable to.
Quoted 4 lines
Please send me the list of patches and oder of application.
Tom
I just checked out u-boot-arm repository and applied my otc570 patch and Jens Scharsigs patch I mentioned above.
[PATCH ARM] updates the at91 main_clock calculation
http://lists.denx.de/pipermail/u-boot/2010-February/067779.html
After applying, build runs without errors.
Daniel
Quoted 3 lines
Quoted 3 lines
Best regards,
Daniel Gorsulowski
PATCH 1/1 AT91: Update otc570 board to new SoC access
Quoted 38 lines · Daniel Gorsulowski
Quoted 37 lines · Tom
Quoted 19 lines · Daniel Gorsulowski
Hello Tom
Quoted 4 lines · Daniel Gorsulowski
* convert otc570 board to use c stucture SoC access
* change gpio access toat91_gpiosyntaxSigned-off-by Daniel Gorsulowski <[email protected]>Quoted 12 lines
---
This patch requires Jens Scharsigs new SoC access patchset.
http://lists.denx.de/pipermail/u-boot/2010-February/067424.html
http://lists.denx.de/pipermail/u-boot/2010-February/067425.html
http://lists.denx.de/pipermail/u-boot/2010-February/067426.html
http://lists.denx.de/pipermail/u-boot/2010-February/067427.html
http://lists.denx.de/pipermail/u-boot/2010-February/067428.html
http://lists.denx.de/pipermail/u-boot/2010-February/067429.html
http://lists.denx.de/pipermail/u-boot/2010-February/067430.html
http://lists.denx.de/pipermail/u-boot/2010-February/067431.html
http://lists.denx.de/pipermail/u-boot/2010-February/067432.htmlQuoted 9 lines
...
I recognized, you didn't apply this patch yet. Is there any reason, or did you
simply slip this patch?Btw. I'm also missing this patch:
http://lists.denx.de/pipermail/u-boot/2010-February/067779.htmlYes.
This was slipped.
I spent some time trying to work out which patches needed to be applied to remove the build errors I was seeing with otc but was unable to.Please send me the list of patches and oder of application.
Quoted 8 lines
Quoted 2 lines
Tom
I just checked out u-boot-arm repository and applied my otc570 patch and Jens Scharsigs patch I mentioned above.
[PATCH ARM] updates the at91main_clockcalculation
http://lists.denx.de/pipermail/u-boot/2010-February/067779.htmlAfter applying, build runs without errors.
I have applied the lastest version of these patches I could find. It does build.
There are some compile warnings
soft_i2c.c: In function 'send_reset':
soft_i2c.c:103: warning: unused variable 'pio'
soft_i2c.c: In function 'send_start':
soft_i2c.c:130: warning: unused variable 'pio'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:147: warning: unused variable 'pio'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:166: warning: unused variable 'pio'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:185: warning: unused variable 'pio'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:259: warning: unused variable 'pio' atmel_dataflash_spi.c:25:2: warning: #warning Please update to use C structur
SoC access !
atmel_usart.c:21:2: warning: #warning Please update to use C structur SoC access ! ohci-at91.c:30:2: warning: #warning Please update to use C structur SoC access
Thanks
Tom
Quoted 5 lines
Daniel
Quoted 2 lines
Quoted 2 lines
Best regards,
Daniel Gorsulowski
PATCH 1/1 AT91: Update otc570 board to new SoC access
In reply to Daniel GorsulowskiQuoted 38 lines · Daniel Gorsulowski
Quoted 37 lines · Tom
Quoted 19 lines · Daniel Gorsulowski
Hello Tom
Quoted 4 lines · Daniel Gorsulowski
* convert otc570 board to use c stucture SoC access
* change gpio access toat91_gpiosyntaxSigned-off-by Daniel Gorsulowski <[email protected]>Quoted 12 lines
---
This patch requires Jens Scharsigs new SoC access patchset.
http://lists.denx.de/pipermail/u-boot/2010-February/067424.html
http://lists.denx.de/pipermail/u-boot/2010-February/067425.html
http://lists.denx.de/pipermail/u-boot/2010-February/067426.html
http://lists.denx.de/pipermail/u-boot/2010-February/067427.html
http://lists.denx.de/pipermail/u-boot/2010-February/067428.html
http://lists.denx.de/pipermail/u-boot/2010-February/067429.html
http://lists.denx.de/pipermail/u-boot/2010-February/067430.html
http://lists.denx.de/pipermail/u-boot/2010-February/067431.html
http://lists.denx.de/pipermail/u-boot/2010-February/067432.htmlQuoted 9 lines
...
I recognized, you didn't apply this patch yet. Is there any reason, or did you
simply slip this patch?Btw. I'm also missing this patch:
http://lists.denx.de/pipermail/u-boot/2010-February/067779.htmlYes.
This was slipped.
I spent some time trying to work out which patches needed to be applied to remove the build errors I was seeing with otc but was unable to.Please send me the list of patches and oder of application.
Quoted 8 lines
Quoted 2 lines
Tom
I just checked out u-boot-arm repository and applied my otc570 patch and Jens Scharsigs patch I mentioned above.
[PATCH ARM] updates the at91main_clockcalculation
http://lists.denx.de/pipermail/u-boot/2010-February/067779.htmlAfter applying, build runs without errors.
I have applied the lastest version of these patches I could find. It does build.
There are some compile warnings
soft_i2c.c: In function 'send_reset':
soft_i2c.c:103: warning: unused variable 'pio'
soft_i2c.c: In function 'send_start':
soft_i2c.c:130: warning: unused variable 'pio'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:147: warning: unused variable 'pio'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:166: warning: unused variable 'pio'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:185: warning: unused variable 'pio'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:259: warning: unused variable 'pio' atmel_dataflash_spi.c:25:2: warning: #warning Please update to use C structur
SoC access !
atmel_usart.c:21:2: warning: #warning Please update to use C structur SoC access ! ohci-at91.c:30:2: warning: #warning Please update to use C structur SoC access
Thanks
Tom
Quoted 5 lines
Daniel
Quoted 2 lines
Quoted 2 lines
Best regards,
Daniel Gorsulowski