Skip to contentSkip to conversation

vlan performance issue on outgoing traffic

DISCUSSION R. Weinedel 2 participants 3 messages Apr 25, 2010 – Apr 28, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

hallo,

I have an performance issue with vlan interfaces on an Debian Lenny server. The problem occurs only on outgoing traffic from the vlan interfaces. They use only half of the available bandwidth - (490 Mbit/s measured with iperf ). Incoming traffic is handled @ 950 Mbit/s and is fine. The issue remains even with no switch and an direct connection between pc and server on the same nic. Removing (on server) the vlans from eth0 and configure one net on eth0 results in full speed (950 Mbit/s) in both directions. Even another nic (onboard nvidia3 - mod forcedeth) couldn't solve it. I tested only in the same networking segment (vlan) without the need for ip forwarding or NAT, but the issue occurs on all my vlan's.

All values were taken with iperf between the server and an ubuntu 9.04 workstation (and vice versa). I have controlled (w. ethtool / stats from switch) that all connection was 1000-BaseT/full duplex. It looks like some kind of trafficshaping to me, but i don't use tc, qos,tos nor other priority handling.

The network ist quite simple: One Server, one switch and then the workstations. No need for cascading or using (r)stp.

Here some information about my network:

Switch: Netgear GSM7224 Layer 2 managed switch, FW 6.2.0.14 (independent, issue remains on direct connection).

Server: Debian Lenny, kernel 2.6.26-2,

NIC: Intel Corporation 82541PI Gigabit Ethernet Con. (e1000 module).

# ethtool eth0
Settings for eth0:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: umbg
        Wake-on: g
        Current message level: 0x00000007 (7)
        Link detected: yes

8021q:

filename:       /lib/modules/2.6.26-2-686/kernel/net/8021q/8021q.ko
version:        1.8
license:        GPL
alias:          rtnl-link-vlan
srcversion:     A61E1168F65EE335A91D4E1

depends:
vermagic: 2.6.26-2-686 SMP mod_unload modversions 686

VLAN: #/proc/net/vlan/config
VLAN Dev name | VLAN ID
Name-Type: VLAN_NAME_TYPE_RAW_PLUS_VID_NO_PAD

eth0.5         | 5  | eth0
eth0.101       | 101  | eth0
eth0.90        | 90  | eth0

IFCONFIG:
eth0 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet6-Adresse: fe80::20e:cff:febc:4343/64
Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
          RX packets:28140829 errors:0 dropped:218 overruns:0 frame:0
          TX packets:44994420 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:1000
          RX bytes:3472864138 (3.2 GiB)  TX bytes:3908682627 (3.6 GiB)

eth0.5 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet Adresse:XXX.YYY.5.1  Bcast:XXX.YYY.5.255  Maske:255.255.255.0
          inet6-Adresse: fe80::20e:cff:febc:4343/64

Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1 RX packets:77807 errors:0 dropped:0 overruns:0 frame:0 TX packets:69699 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:57578233 (54.9 MiB) TX bytes:7782844 (7.4 MiB)

eth0.90 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet Adresse:XXX.YYY.90.1  Bcast:XXX.YYY.90.255 
Maske:255.255.255.0
          inet6-Adresse: fe80::20e:cff:febc:4343/64
Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
          RX packets:457850 errors:0 dropped:0 overruns:0 frame:0
          TX packets:913988 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:0
          RX bytes:23824841 (22.7 MiB)  TX bytes:1311485281 (1.2 GiB)

eth0.101 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet Adresse:XXX.YYY.101.1  Bcast:XXX.YYY.101.255 
Maske:255.255.255.0
          inet6-Adresse: fe80::20e:cff:febc:4343/64
Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
          RX packets:24856818 errors:0 dropped:0 overruns:0 frame:0
          TX packets:41608593 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:0
          RX bytes:423116676 (403.5 MiB)  TX bytes:3855703636 (3.5 GiB)

ROUTE: #route -n
Ziel Router Genmask Flags Metric Ref Use
Iface
XXX.YYY.101.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0.101
XXX.YYY.5.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0.5
XXX.YYY.90.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0.90
0.0.0.0 192.168.5.4 0.0.0.0 UG 0 0 0
eth0.5

Can someone give me a hint, where my search for an solution should be going on ?

Many thanks !
Regards
Ralf Weinedel
Falkensee/Germany

#1 lore raw
Quoted 23 lines · R. Weinedel

hallo,

I have an performance issue with vlan interfaces on an Debian Lenny server. The problem occurs only on outgoing traffic from the vlan interfaces. They use only half of the available bandwidth - (490 Mbit/s measured with iperf ). Incoming traffic is handled @ 950 Mbit/s and is fine. The issue remains even with no switch and an direct connection between pc and server on the same nic. Removing (on server) the vlans from eth0 and configure one net on eth0 results in full speed (950 Mbit/s) in both directions. Even another nic (onboard nvidia3 - mod forcedeth) couldn't solve it. I tested only in the same networking segment (vlan) without the need for ip forwarding or NAT, but the issue occurs on all my vlan's.

All values were taken with iperf between the server and an ubuntu 9.04 workstation (and vice versa). I have controlled (w. ethtool / stats from switch) that all connection was 1000-BaseT/full duplex. It looks like some kind of trafficshaping to me, but i don't use tc, qos,tos nor other priority handling.

The network ist quite simple: One Server, one switch and then the workstations. No need for cascading or using (r)stp.

Quoted 6 lines

Here some information about my network:

Switch: Netgear GSM7224 Layer 2 managed switch, FW 6.2.0.14 (independent, issue remains on direct connection).

Server: Debian Lenny, kernel 2.6.26-2,

This version of the kernel doesn't support offloads for vlan adapters, which is probably causing most of your decrease in throughput due to either exhausting socket buffer size, or because of the round trip time being so much more relevant when not sending large bursts using TSO. Sometimes the flood of ACK packets causes higher cpu which could reduce your throughput also.

The newer kernels will have a major impact on your setup due to a patch that enabled pass through of hardware offloads to the vlan device's offload advertisement.

The commit id of the patch is 5fb13570543f4ae022996c9d7c0c099c8abf22dd, you can view it at:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=5fb13570543f4ae022996c9d7c0c099c8abf22dd

Quoted 1 line

NIC: Intel Corporation 82541PI Gigabit Ethernet Con. (e1000 module).

This PCI adapter is bandwidth limited on the PCI bus, and so will be even more sensitive to offload on (TSO) vs offload off.

Quoted 104 lines
# ethtool eth0
Settings for eth0:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: umbg
        Wake-on: g
        Current message level: 0x00000007 (7)
        Link detected: yes

8021q:

filename:       /lib/modules/2.6.26-2-686/kernel/net/8021q/8021q.ko
version:        1.8
license:        GPL
alias:          rtnl-link-vlan
srcversion:     A61E1168F65EE335A91D4E1

depends:
vermagic: 2.6.26-2-686 SMP mod_unload modversions 686

VLAN: #/proc/net/vlan/config
VLAN Dev name | VLAN ID
Name-Type: VLAN_NAME_TYPE_RAW_PLUS_VID_NO_PAD

eth0.5         | 5  | eth0
eth0.101       | 101  | eth0
eth0.90        | 90  | eth0

IFCONFIG:
eth0 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet6-Adresse: fe80::20e:cff:febc:4343/64
Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
          RX packets:28140829 errors:0 dropped:218 overruns:0 frame:0
          TX packets:44994420 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:1000
          RX bytes:3472864138 (3.2 GiB)  TX bytes:3908682627 (3.6 GiB)

eth0.5 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet Adresse:XXX.YYY.5.1  Bcast:XXX.YYY.5.255  Maske:255.255.255.0
          inet6-Adresse: fe80::20e:cff:febc:4343/64

Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1 RX packets:77807 errors:0 dropped:0 overruns:0 frame:0 TX packets:69699 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:57578233 (54.9 MiB) TX bytes:7782844 (7.4 MiB)

eth0.90 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet Adresse:XXX.YYY.90.1  Bcast:XXX.YYY.90.255 
Maske:255.255.255.0
          inet6-Adresse: fe80::20e:cff:febc:4343/64
Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
          RX packets:457850 errors:0 dropped:0 overruns:0 frame:0
          TX packets:913988 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:0
          RX bytes:23824841 (22.7 MiB)  TX bytes:1311485281 (1.2 GiB)

eth0.101 Link encap:Ethernet Hardware Adresse 00:0e:0c:bc:43:43

          inet Adresse:XXX.YYY.101.1  Bcast:XXX.YYY.101.255 
Maske:255.255.255.0
          inet6-Adresse: fe80::20e:cff:febc:4343/64
Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
          RX packets:24856818 errors:0 dropped:0 overruns:0 frame:0
          TX packets:41608593 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:0
          RX bytes:423116676 (403.5 MiB)  TX bytes:3855703636 (3.5 GiB)

ROUTE: #route -n
Ziel Router Genmask Flags Metric Ref Use
Iface
XXX.YYY.101.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0.101
XXX.YYY.5.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0.5
XXX.YYY.90.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0.90
0.0.0.0 192.168.5.4 0.0.0.0 UG 0 0 0
eth0.5

Can someone give me a hint, where my search for an solution should be going on ?

Many thanks !
Regards
Ralf Weinedel
Falkensee/Germany

--
To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw

Re: vlan performance issue on outgoing traffic (solved)

I made some further test with kernel 2.6.26 and I recognized that my cpu is really very busy (90-100 % sw-irq's) during offloads.

After that I build and install a 2.6.33 kernel and the problem seems to be solved. Now I got 946 Mbit/s offload (iperf) !.

Ralf Weinedel