Fix SJA1000 command register writes on SMP systems
Subsystems (3)
PATCH v2 1/1 Fix SJA1000 command register writes on SMP systems
The SJA1000 command register is concurrently written in the rx-path to free the receive buffer _and_ in the tx-path to start the transmission.
The SJA1000 data sheet, 6.4.4 COMMAND REGISTER (CMR) states:
"Between two commands at least one internal clock cycle is needed in order to proceed. The internal clock is half of the external oscillator frequency."
On SMP systems this leads to a write stall in the tx-path, which can be solved by adding some locking for the command register in the SMP case. In this special case we also read the status register to settle the command register write.
Thanks to Klaus Hitschler for the original fix and detailed problem description.
This patch applies on net-2.6 and (with some offsets) on net-next-2.6 .
---
drivers/net/can/sja1000/sja1000.c +22 -1
@@ -84,6 +84,27 @@ static struct can_bittiming_const sja1000_bittiming_const = { .brp_inc = 1, }; +static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val) +{ +/* the command register needs some locking on SMP systems */ + +#ifdef CONFIG_SMP + +unsigned long flags; + +spin_lock_irqsave (&priv->cmdreg_lock, flags); + priv->write_reg (priv,REG_CMR , val); + priv->read_reg (priv,REG_SR ); +spin_unlock_irqrestore (&priv->cmdreg_lock, flags); + +#else + +/* write to the command register without locking */ + priv->write_reg (priv,REG_CMR , val); + +#endif +} +static int sja1000_probe_chip (struct net_device *dev) {struct sja1000_priv *priv =netdev_priv (dev);
@@ -297,7 +318,7 @@ static netdev_tx_t sja1000_start_xmit(struct sk_buff *skb,can_put_echo_skb (skb, dev,0 ); - priv->write_reg (priv,REG_CMR ,CMD_TR ); +sja1000_write_cmdreg (priv,CMD_TR );return NETDEV_TX_OK ; }
@@ -346,7 +367,7 @@ static void sja1000_rx(struct net_device *dev) cf->can_id = id;/* release receive buffer */ - priv->write_reg (priv,REG_CMR ,CMD_RRB ); +sja1000_write_cmdreg (priv,CMD_RRB );netif_rx (skb); @@ -374,7 +395,7 @@ static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status) cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; stats->rx_over_errors++;
stats->rx_errors++;
- priv->write_reg(priv, REG_CMR, CMD_CDO); /* clear bit */
+ sja1000_write_cmdreg(priv, CMD_CDO); /* clear bit */
}
if (isrc & IRQ_EI) {
drivers/net/can/sja1000/sja1000.h +3 -0
@@ -168,6 +168,10 @@ struct sja1000_priv {void __iomem *reg_base;/* ioremap'ed address to registers */ unsigned long irq_flags;/* for request_irq() */ +#ifdef CONFIG_SMP +spinlock_t cmdreg_lock;/* lock for concurrent cmd register writes */ +#endif +u16 flags;/* custom mode flags */ u8 ocr;/* output control register */ u8 cdr;/* clock divider register */
David Miller
maintainerFrom: Oliver Hartkopp <[email protected]>
Date: Mon, 17 May 2010 22:17:40 +0200
drivers/net/can/sja1000/sja1000.c static struct can_bittiming_const sja1000_bittiming_const = { · line 90
Quoted 12 lines
drivers/net/can/sja1000/sja1000.c +4
-0@@ -84,6 +84,27 @@ static struct can_bittiming_const sja1000_bittiming_const = { .brp_inc = 1, }; +static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val) +{ +/* the command register needs some locking on SMP systems */ + +#ifdef CONFIG_SMP
Something is adding spurious leading spaces to lines in your patch.
Also, please don't SMP conditionalize this code. It makes it such that lock debugging et al. can't be used to check this code on uniprocessor.
A message that is not in the archive (sent off-list or not yet received): 20100517.223415.184853371.davem-fT/PcQaiUtIeIZ0/[email protected]
Quoted 17 lines · David Miller
From: Oliver Hartkopp <[email protected]>
Date: Mon, 17 May 2010 22:17:40 +0200drivers/net/can/sja1000/sja1000.c static struct can_bittiming_const sja1000_bittiming_const = { · line 90
Quoted 12 lines
drivers/net/can/sja1000/sja1000.c +4
-0@@ -84,6 +84,27 @@ static struct can_bittiming_const sja1000_bittiming_const = { .brp_inc = 1, }; +static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val) +{ +/* the command register needs some locking on SMP systems */ + +#ifdef CONFIG_SMP Something is adding spurious leading spaces to lines in your patch.
Sorry. This was probably due to the v2 resend. Will fix.
Quoted 2 lines
Also, please don't SMP conditionalize this code. It makes it such that lock debugging et al. can't be used to check this code on uniprocessor.
Ok.
Will send an updated v3 patch shortly.
Thanks,
Oliver