MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
Subsystems (2)
PATCH 1/1 MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
Tested on actual hardware using the g_ether and g_serial gadget drivers.
---
Applies on top of Linus' git tree.
To test this the mx3_defconfig was used but with USB gadget activated.
arch/arm/mach-mx3/mach-mx31_3ds.c | 55 +++++++++++++++++++++++++++++++++++++ 1 files changed, 55 insertions(+), 0 deletions(-)
arch/arm/mach-mx3/mach-mx31_3ds.c +55 -0
@@ -16,6 +16,7 @@* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +#include <linux/delay.h> #include <linux/types.h> #include <linux/init.h> #include <linux/clk.h>
@@ -26,6 +27,7 @@#include <linux/mfd/mc13783.h> #include <linux/spi/spi.h> #include <linux/regulator/machine.h> +#include <linux/fsl_devices.h> #include <mach/hardware.h> #include <asm/mach-types.h>
@@ -65,6 +67,21 @@ static int mx31_3ds_pins[] = {MX31_PIN_CSPI2_SS2__SS2 ,/*CS for MC13783 */ /* MC13783 IRQ */ IOMUX_MODE (MX31_PIN_GPIO1_3 ,IOMUX_CONFIG_GPIO ), +/* USB OTG reset */ +IOMUX_MODE (MX31_PIN_USB_PWR ,IOMUX_CONFIG_GPIO ), +/* USB OTG */ +MX31_PIN_USBOTG_DATA0__USBOTG_DATA0 , +MX31_PIN_USBOTG_DATA1__USBOTG_DATA1 , +MX31_PIN_USBOTG_DATA2__USBOTG_DATA2 , +MX31_PIN_USBOTG_DATA3__USBOTG_DATA3 , +MX31_PIN_USBOTG_DATA4__USBOTG_DATA4 , +MX31_PIN_USBOTG_DATA5__USBOTG_DATA5 , +MX31_PIN_USBOTG_DATA6__USBOTG_DATA6 , +MX31_PIN_USBOTG_DATA7__USBOTG_DATA7 , +MX31_PIN_USBOTG_CLK__USBOTG_CLK , +MX31_PIN_USBOTG_DIR__USBOTG_DIR , +MX31_PIN_USBOTG_NXT__USBOTG_NXT , + MX31_PIN_USBOTG_STP__USBOTG_STP, };/* Regulators */
@@ -126,6 +143,41 @@ static struct mxc_nand_platform_data imx31_3ds_nand_flash_pdata = {#endif }; +/* +* USB OTG +*/ + +#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \ + PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU) + +#define USBOTG_RST_B IOMUX_TO_GPIO(MX31_PIN_USB_PWR) + +static void mx31_3ds_usbotg_init (void ) +{ +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA0 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA1 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA2 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA3 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA4 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA5 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA6 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DATA7 ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_CLK ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_DIR ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_NXT ,USB_PAD_CFG ); +mxc_iomux_set_pad (MX31_PIN_USBOTG_STP ,USB_PAD_CFG ); + +gpio_request (USBOTG_RST_B ,"otgusb-reset" ); +gpio_direction_output (USBOTG_RST_B ,0 ); +mdelay (1 ); +gpio_set_value (USBOTG_RST_B ,1 ); +} + +static struct fsl_usb2_platform_data usbotg_pdata = { + .operating_mode =FSL_USB2_DR_DEVICE , + .phy_mode =FSL_USB2_PHY_ULPI , +}; +static struct imxuart_platform_data uart_pdata = { .flags =IMXUART_HAVE_RTSCTS , };
@@ -315,6 +367,9 @@ static void __init mxc_board_init(void)spi_register_board_info (mx31_3ds_spi_devs,ARRAY_SIZE (mx31_3ds_spi_devs)); +mx31_3ds_usbotg_init (); +mxc_register_device (&mxc_otg_udc_device, &usbotg_pdata); +if (!mx31_3ds_init_expio ())platform_device_register (&smsc911x_device); }
Signature · 1 line
1.6.4.2
PATCH 1/1 MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
Hi Magnus,
Quoted 8 lines · Magnus Lilja
From: Magnus Lilja <[email protected]>
Subject: [PATCH] MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
To: linux-arm-kernel at lists.infradead.org
Cc: s.hauer at pengutronix.de
Date: Friday, May 14, 2010, 12:08 PM
Tested on actual hardware using theg_etherandg_serialgadget drivers.
Quoted 6 lines
Signed-off-by Magnus Lilja <[email protected]>---
Applies on top of Linus' git tree.
To test this themx3_defconfigwas used but with USB gadget activated.
Would be good to send a patch for updating the mx3_defconfig with the USB gadget support.
Regards,
Fabio Estevam
PATCH 1/1 MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
Hi Fabio
Quoted 12 lines · Fabio Estevam
Hi Magnus,
Quoted 8 lines · Magnus Lilja
From: Magnus Lilja <[email protected]>
Subject: [PATCH] MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
To: linux-arm-kernel at lists.infradead.org
Cc: s.hauer at pengutronix.de
Date: Friday, May 14, 2010, 12:08 PM
Tested on actual hardware using theg_etherandg_serialgadget drivers.
Quoted 8 lines
Quoted 6 lines
Signed-off-by Magnus Lilja <[email protected]>---
Applies on top of Linus' git tree.
To test this themx3_defconfigwas used but with USB gadget activated.Would be good to send a patch for updating the
mx3_defconfigwith the USB gadget support.
Yes, perhaps that can be done later when bringing the defconfig uptodate (also awaiting inclusion of Alberto Panizzo's keypad patch).
Regards, Magnus Lilja
PATCH 1/1 MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
Hi Magnus,
--- On Fri, 5/14/10, Magnus Lilja <[email protected]> wrote:
...
Quoted 7 lines
Quoted 1 line
Would be good to send a patch for updating the
mx3_defconfigwith the USB gadget support.Yes, perhaps that can be done later when bringing the defconfig
uptodate (also awaiting inclusion of Alberto Panizzo's keypad patch).
Alberto's keypad patches are in mxc-master now. Would you care to update the mx3_defconfig ?
Regards,
Fabio Estevam
PATCH 1/1 MXC: Add USB OTG (device) for i.MX31 PDK (3DS) board.
Hi Fabio
Quoted 7 lines · Fabio Estevam
Hi Magnus,
--- On Fri, 5/14/10, Magnus Lilja <[email protected]> wrote:
...
Quoted 1 line
Quoted 1 line
Would be good to send a patch for updating the
Quoted 8 lines
Quoted 6 lines
mx3_defconfigwith the USB gadget support.Yes, perhaps that can be done later when bringing the defconfig
uptodate (also awaiting inclusion of Alberto Panizzo's keypad patch).Alberto's keypad patches are in mxc-master now. Would you care to update the
mx3_defconfig?
Sure, I'll give it a try.
/Magnus