Skip to contentSkip to conversation

add new board pm9g45

PATCH New Asen Dimov 3 participants 3 messages Apr 20, 2010 – Jun 7, 2010

Subsystems (2)
Kbuild Arm/Microchip (AT91) SoC support
lore
Share & tools
lore

Asen Dimov

author
#0 lore raw

PATCH v3 1/1 add new board pm9g45

Add the new board PM9G45 from Ronetix GmbH.
* AT91SAM9G45 MCU at 400Mhz.
* 128MB DDR2 SDRAM
* 256MB NAND
* 10/100 MBits Ethernet DP83848
* Serial number chip DS2401

The board is made as SODIMM200 module.
For more info www.ronatix.at or info at ronetix.at.

Signed-off-by Asen Dimov <[email protected]>
---
 MAINTAINERS                                        |    1 +
 MAKEALL                                            |    1 +
 Makefile                                           |    4 +
 board/ronetix/pm9g45/Makefile                      |   54 ++++++
 .../at91sam9m10g45ek => ronetix/pm9g45}/config.mk  |    0 
 board/ronetix/pm9g45/pm9g45.c                      |  188 ++++++++++++++++++++
 include/configs/pm9g45.h                           |  186 +++++++++++++++++++
 7 files changed, 434 insertions(+), 0 deletions(-)
 create mode 100644 board/ronetix/pm9g45/Makefile
 copy board/{atmel/at91sam9m10g45ek => ronetix/pm9g45}/config.mk (100%)
 create mode 100644 board/ronetix/pm9g45/pm9g45.c
 create mode 100644 include/configs/pm9g45.h
MAINTAINERS +1 -0
index 0e759c9..a3993fc 100644
@@ -224,6 +224,7 @@ Ilko Iliev <[email protected]>
 
 	PM9261		AT91SAM9261
 	PM9263		AT91SAM9263
+	PM9G45		ARM926EJS (AT91SAM9G45 SoC)
 
 Gary Jennejohn <[email protected]>
MAKEALL +1 -0
index b15d407..911983e 100755
@@ -672,6 +672,7 @@ LIST_at91="			\
 	otc570			\
 	pm9261			\
 	pm9263			\
+	pm9g45			\
 	SBC35_A9G20		\
 	TNY_A9260		\
 	TNY_A9G20		\
Makefile +4 -0
index 8b4e0b9..46845a5 100644
@@ -2871,6 +2871,10 @@ otc570_config	:	unconfig
 pm9263_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91
 
+pm9g45_config	:	unconfig
+	@mkdir -p $(obj)include
+	@$(MKCONFIG) -a pm9g45 arm arm926ejs pm9g45 ronetix at91
+
 SBC35_A9G20_NANDFLASH_config \
 SBC35_A9G20_EEPROM_config \
 SBC35_A9G20_config	:	unconfig
board/ronetix/pm9g45/Makefile new file +54 -0

54 lines not on this page · raw message

board/ronetix/pm9g45/config.mk renamed from board/atmel/at91sam9m10g45ek/config.mk +0 -0
similarity index 100%
copy from board/atmel/at91sam9m10g45ek/config.mk
copy to board/ronetix/pm9g45/config.mk
board/ronetix/pm9g45/pm9g45.c new file +188 -0

188 lines not on this page · raw message

include/configs/pm9g45.h new file +186 -0

186 lines not on this page · raw message

Signature · 1 line
1.5.5.6
Applied
#1 lore raw

PATCH v3 1/1 add new board pm9g45

Quoted 11 lines · Asen Dimov

Add the new board PM9G45 from Ronetix GmbH.
* AT91SAM9G45 MCU at 400Mhz.
* 128MB DDR2 SDRAM
* 256MB NAND
* 10/100 MBits Ethernet DP83848
* Serial number chip DS2401

The board is made as SODIMM200 module.
For more info www.ronatix.at or info at ronetix.at.

Signed-off-by Asen Dimov <[email protected]>

Applied to arm/master.
Thanks
Tom

#2 lore raw

[U-Boot] P20xx/P10xx/MPC85xx eSPI direct boot

Has anyone come across (or written) a tool/script/makefile target to pack u-boot into a SPI boot image (i.e. with boot header and config symbols) to boot directly from SPI on the P2020RDB (or P1020 etc.) and/or MPC8536DS? Would it be within the scope of u-boot to have such an option?

Can