S5PV210: FB: Add MIPI-DSI and CPU Interface features.

index 27d3b49..193f6ea 100644
@@ -22,6 +22,11 @@
  */
 #define S3C_FB_MAX_WIN	(5)
 
+enum {
+	FIMD_VIDEO_MODE = 0,
+	FIMD_COMMAND_MODE
+};
+
 /**
  * struct s3c_fb_pd_win - per window setup data
  * @win_mode: The display parameters to initialise (not for window 0)

@@ -30,6 +35,7 @@
  */
 struct s3c_fb_pd_win {
 	struct fb_videomode	win_mode;
+	struct fb_cmdmode	cmd_mode;
 
 	unsigned short		default_bpp;
 	unsigned short		max_bpp;

@@ -42,6 +48,7 @@ struct s3c_fb_pd_win {
  * @setup_gpio: Setup the external GPIO pins to the right state to transfer
  *		the data from the display system to the connected display
  *		device.
+ * @interface_mode: cpu mode or rgb mode.
  * @vidcon0: The base vidcon0 values to control the panel data format.
  * @vidcon1: The base vidcon1 values to control the panel data output.
  * @win: The setup data for each hardware window, or NULL for unused.

@@ -57,6 +64,7 @@ struct s3c_fb_platdata {
 	void	(*setup_gpio)(void);
 
 	struct s3c_fb_pd_win	*win[S3C_FB_MAX_WIN];
+	u32			interface_mode;
 
 	u32			 vidcon0;
 	u32			 vidcon1;

@@ -91,4 +99,10 @@ extern void s5pc100_fb_gpio_setup_24bpp(void);
  */
 extern void s5pv210_fb_gpio_setup_24bpp(void);
 
+struct fb_info;
+
+extern void s3c_fb_set_trigger(struct fb_info *info);
+
+extern int s3c_fb_is_i80_frame_done(struct fb_info *info);
+
 #endif /* __PLAT_S3C_FB_H */

index 0f43599..4d5954b 100644
@@ -135,6 +135,22 @@
 
 #define WPALCON					(0x1A0)
 
+/* For CPU interface. */
+#define TRIGCON						(0x1a4)
+#define TRGMODE_I80_ENABLE				(1 << 0)
+#define SWTRGCMD_I80_TRIGGER				(1 << 1)
+#define SWFRSTATUS_I80					(1 << 2)
+
+#define I80IFCONA0					(0x1b0)
+#define I80IFEN_ENABLE					(1 << 0)
+#define RSPOL_HIGH					(1 << 2)
+#define LCD_WR_HOLD(x)					(((x) & 0xf) << 4)
+#define LCD_WR_ACT(x)					(((x) & 0xf) << 8)
+#define LCD_WR_SETUP(x)					(((x) & 0xf) << 12)
+#define LCD_CS_SETUP(x)					(((x) & 0xf) << 16)
+
+#define I80IFCONB0					(0x1b8)
+
 /* Palette control */
 /* Note for S5PC100: you can still use those macros on WPALCON (aka WPALCON_L),
  * but make sure that WPALCON_H W2PAL-W4PAL entries are zeroed out */

index 0ef806e..70342aa 100644
@@ -38,6 +38,7 @@
 #define VIDCON0_VIDOUT_TV			(0x1 << 26)
 #define VIDCON0_VIDOUT_I80_LDI0			(0x2 << 26)
 #define VIDCON0_VIDOUT_I80_LDI1			(0x3 << 26)
+#define VIDCON0_DSI_EN_ENABLE			(1 << 30)
 
 #define VIDCON0_L1_DATA_MASK			(0x7 << 23)
 #define VIDCON0_L1_DATA_SHIFT			(23)

187 lines not on this page · raw message