Skip to contentSkip to conversation

arm, 926: convert all arm926ejs based board

RFC PATCH New Heiko Schocher 1 participant 1 message Jul 29, 2010

Subsystems (3)
Arm (32-bit) Arm i.MX and Layerscape Arm/Microchip (AT91) SoC support
lore
Share & tools
lore

Heiko Schocher

author
#0 lore raw

RFC PATCH 15/19 arm, 926: convert all arm926ejs based board

Signed-off-by Heiko Schocher <[email protected]>
---
 arch/arm/cpu/arm926ejs/orion5x/dram.c           |   12 ++++++++++--
 board/Marvell/guruplug/guruplug.c               |   15 ++++++++++++---
 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c |   12 ++++++++++--
 board/Marvell/openrd_base/openrd_base.c         |   11 +++++++++--
 board/Marvell/rd6281a/rd6281a.c                 |   15 ++++++++++++---
 board/Marvell/sheevaplug/sheevaplug.c           |   15 ++++++++++++---
 board/armltd/versatile/versatile.c              |   10 ++++++++++
 board/atmel/at91cap9adk/at91cap9adk.c           |   11 +++++++++--
 board/atmel/at91sam9260ek/at91sam9260ek.c       |   11 +++++++++--
 board/atmel/at91sam9261ek/at91sam9261ek.c       |   11 +++++++++--
 board/atmel/at91sam9263ek/at91sam9263ek.c       |   11 +++++++++--
 board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c |   11 +++++++++--
 board/atmel/at91sam9rlek/at91sam9rlek.c         |   11 +++++++++--
 board/calao/sbc35_a9g20/sbc35_a9g20.c           |   15 ++++++++++-----
 board/calao/tny_a9260/tny_a9260.c               |   14 +++++++++-----
 board/davinci/common/misc.c                     |   12 +++++++++---
 board/esd/meesc/meesc.c                         |   13 ++++++++++---
 board/esd/otc570/otc570.c                       |   13 ++++++++++---
 board/eukrea/cpu9260/cpu9260.c                  |   15 ++++++++++-----
 board/karo/tx25/tx25.c                          |    6 ++----
 board/keymile/km_arm/km_arm.c                   |   13 +++++++++++--
 board/logicpd/imx27lite/config.mk               |    2 +-
 board/logicpd/imx27lite/imx27lite.c             |   15 +++++++++------
 board/ronetix/pm9261/pm9261.c                   |   13 ++++++++++---
 board/ronetix/pm9263/pm9263.c                   |   13 ++++++++++---
 board/ronetix/pm9g45/pm9g45.c                   |   13 ++++++++++---
 board/st/nhk8815/nhk8815.c                      |   11 +++++++++--
 board/ti/omap1510inn/config.mk                  |    3 ++-
 board/ti/omap1510inn/omap1510innovator.c        |   13 +++++++++----
 board/ti/omap1610inn/config.mk                  |    3 ++-
 board/ti/omap1610inn/omap1610innovator.c        |   12 +++++++++---
 board/ti/omap5912osk/omap5912osk.c              |   12 +++++++++---
 board/ti/omap730p2/omap730p2.c                  |   12 +++++++++---
 include/configs/at91cap9adk.h                   |    4 ++++
 include/configs/at91sam9260ek.h                 |    4 ++++
 include/configs/at91sam9261ek.h                 |    4 ++++
 include/configs/at91sam9263ek.h                 |    4 ++++
 include/configs/at91sam9m10g45ek.h              |    4 ++++
 include/configs/at91sam9rlek.h                  |    4 ++++
 include/configs/cpu9260.h                       |    4 ++++
 include/configs/da830evm.h                      |    5 +++++
 include/configs/da850evm.h                      |    4 ++++
 include/configs/davinci_dm355evm.h              |    4 ++++
 include/configs/davinci_dm355leopard.h          |    4 ++++
 include/configs/davinci_dm365evm.h              |    4 ++++
 include/configs/davinci_dm6467evm.h             |    4 ++++
 include/configs/davinci_dvevm.h                 |    6 ++++++
 include/configs/davinci_schmoogie.h             |    5 +++++
 include/configs/davinci_sffsdr.h                |    5 +++++
 include/configs/davinci_sonata.h                |    6 ++++++
 include/configs/edminiv2.h                      |    4 ++++
 include/configs/guruplug.h                      |    4 ++++
 include/configs/imx27lite-common.h              |    4 ++++
 include/configs/km_arm.h                        |    4 ++++
 include/configs/meesc.h                         |    4 ++++
 include/configs/mv88f6281gtw_ge.h               |    4 ++++
 include/configs/nhk8815.h                       |    4 ++++
 include/configs/ns9750dev.h                     |    4 ++++
 include/configs/omap1610h2.h                    |    4 ++++
 include/configs/omap1610inn.h                   |    4 ++++
 include/configs/omap5912osk.h                   |    4 ++++
 include/configs/omap730p2.h                     |    4 ++++
 include/configs/openrd_base.h                   |    4 ++++
 include/configs/otc570.h                        |    4 ++++
 include/configs/pm9261.h                        |    4 ++++
 include/configs/pm9263.h                        |    4 ++++
 include/configs/pm9g45.h                        |    4 ++++
 include/configs/rd6281a.h                       |    4 ++++
 include/configs/sbc35_a9g20.h                   |    4 ++++
 include/configs/sheevaplug.h                    |    4 ++++
 include/configs/tny_a9260.h                     |    4 ++++
 include/configs/versatile.h                     |    4 ++++
 72 files changed, 452 insertions(+), 90 deletions(-)
arch/arm/cpu/arm926ejs/orion5x/dram.c +10 -2
index c719798..d490880 100644
@@ -50,7 +50,16 @@ u32 orion5x_sdram_bar(enum memory_bank bank)
 	return result;
 }
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size(
+			(volatile long *) orion5x_sdram_bar(0),
+			CONFIG_MAX_RAM_BANK_SIZE);
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	int i;
 

@@ -60,5 +69,4 @@ int dram_init(void)
 			(volatile long *) (gd->bd->bi_dram[i].start),
 			CONFIG_MAX_RAM_BANK_SIZE);
 	}
-	return 0;
 }
board/Marvell/guruplug/guruplug.c +12 -3
index c028a53..761e014 100644
@@ -108,15 +108,24 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	/* Fix this */
+	gd->ram_size = get_ram_size((volatile void *)kw_sdram_bar(0),
+				kw_sdram_bs(0));
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	int i;
 
 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
 		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+		gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i),
+						       kw_sdram_bs(i));
 	}
-	return 0;
 }
 
 #ifdef CONFIG_RESET_PHY_R
board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c +10 -2
index c959bf8..3a98f72 100644
@@ -110,7 +110,16 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	/* Fix this */
+	gd->ram_size = get_ram_size((volatile void *)kw_sdram_bar(0),
+				kw_sdram_bs(0));
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	int i;
 

@@ -118,7 +127,6 @@ int dram_init(void)
 		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
 		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
 	}
-	return 0;
 }
 
 #ifdef CONFIG_MV88E61XX_SWITCH
board/Marvell/openrd_base/openrd_base.c +9 -2
index c00a08a..409dfb8 100644
@@ -113,7 +113,15 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				kw_sdram_bs(0));
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	int i;
 

@@ -121,7 +129,6 @@ int dram_init(void)
 		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
 		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
 	}
-	return 0;
 }
 
 #ifdef CONFIG_RESET_PHY_R
board/Marvell/rd6281a/rd6281a.c +12 -3
index 8713a3c..eec89c7 100644
@@ -109,15 +109,24 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	/* Fix this */
+	gd->ram_size = get_ram_size((volatile void *)kw_sdram_bar(0),
+				kw_sdram_bs(0));
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	int i;
 
 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
 		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+		gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i),
+						       kw_sdram_bs(i));
 	}
-	return 0;
 }
 
 void mv_phy_88e1116_init(char *name)
board/Marvell/sheevaplug/sheevaplug.c +12 -3
index 547126a..2fb5141 100644
@@ -108,15 +108,24 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	/* Fix this */
+	gd->ram_size = get_ram_size((volatile void *)kw_sdram_bar(0),
+				kw_sdram_bs(0));
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	int i;
 
 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
 		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+		gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i),
+						       kw_sdram_bs(i));
 	}
-	return 0;
 }
 
 #ifdef CONFIG_RESET_PHY_R
board/armltd/versatile/versatile.c +10 -0
index 6e836dd..0a138b4 100644
@@ -88,9 +88,19 @@ int misc_init_r (void)
 ******************************/
 int dram_init (void)
 {
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = get_ram_size((volatile void *)PHYS_SDRAM_1,
+			PHYS_SDRAM_1_SIZE);
+}
+
 #ifdef CONFIG_CMD_NET
 int board_eth_init(bd_t *bis)
 {
board/atmel/at91cap9adk/at91cap9adk.c +9 -2
index 2ab8bc2..03e767a 100644
@@ -331,11 +331,18 @@ int board_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/atmel/at91sam9260ek/at91sam9260ek.c +9 -2
index 64c6d17..4c62420 100644
@@ -171,11 +171,18 @@ int board_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/atmel/at91sam9261ek/at91sam9261ek.c +9 -2
index de5cfae..69aa5b6 100644
@@ -273,11 +273,18 @@ int board_eth_init(bd_t *bis)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/atmel/at91sam9263ek/at91sam9263ek.c +9 -2
index 91efc07..72314fa 100644
@@ -276,11 +276,18 @@ int board_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c +9 -2
index f92b20f..1f525fa 100644
@@ -283,11 +283,18 @@ int board_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/atmel/at91sam9rlek/at91sam9rlek.c +9 -2
index e374917..87a79e6 100644
@@ -199,7 +199,14 @@ int board_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
+
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
board/calao/sbc35_a9g20/sbc35_a9g20.c +10 -5
index 9df45c0..ccac942 100644
@@ -164,16 +164,21 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	if(get_ram_size((long *) PHYS_SDRAM, PHYS_SDRAM_SIZE) != PHYS_SDRAM_SIZE)
+	/* dram_init must store complete ramsize in gd->ram_size */
+	if(get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, PHYS_SDRAM_SIZE) != PHYS_SDRAM_SIZE)
 		return -1;
-
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	gd->ram_size = PHYS_SDRAM_SIZE;
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].start = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/calao/tny_a9260/tny_a9260.c +9 -5
index d51ca15..7d4dc0f 100644
@@ -99,12 +99,16 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	if(get_ram_size((long *) PHYS_SDRAM, PHYS_SDRAM_SIZE) != PHYS_SDRAM_SIZE)
+	if(get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, PHYS_SDRAM_SIZE) != PHYS_SDRAM_SIZE)
 		return -1;
-
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	gd->ram_size = PHYS_SDRAM_SIZE;
 	return 0;
 }
+
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].start = gd->ram_size;
+}
board/davinci/common/misc.c +9 -3
index 25ca326..b4c5d7a 100644
@@ -35,10 +35,16 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
+	return 0;
+}
 
-	return(0);
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
 }
 
 #ifdef CONFIG_DRIVER_TI_EMAC
board/esd/meesc/meesc.c +10 -3
index a1b66cb..74467c5 100644
@@ -139,13 +139,20 @@ static void meesc_ethercat_hw_init(void)
 	at91_set_B_periph(AT91_PIN_PE20, 0);	/* EBI1_NWAIT */
 }
 
-int dram_init(void)
+int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1 << 27));
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				(1 << 27));
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
board/esd/otc570/otc570.c +10 -3
index 07d9c62..5b36a31 100644
@@ -237,13 +237,20 @@ void lcd_show_board_info(void)
 #endif /* CONFIG_LCD_INFO */
 #endif /* CONFIG_LCD */
 
-int dram_init(void)
+int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1 << 27));
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				get_ram_size((long *) PHYS_SDRAM, (1 << 27)));
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
board/eukrea/cpu9260/cpu9260.c +10 -5
index 61b6c33..e00894d 100644
@@ -188,15 +188,20 @@ int board_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	if (get_ram_size((long *) PHYS_SDRAM, PHYS_SDRAM_SIZE) !=
-	    PHYS_SDRAM_SIZE)
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
+	if (gd->ram_size != PHYS_SDRAM_SIZE)
 		return -1;
-
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/karo/tx25/tx25.c +2 -4
index 3940106..eb03987 100644
@@ -160,22 +160,20 @@ int board_late_init(void)
 int dram_init (void)
 {
 	/* dram_init must store complete ramsize in gd->ram_size */
-	gd->ram_size = get_ram_size((volatile void *)PHYS_SDRAM_1,
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
 				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
 void dram_init_banksize (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 	gd->bd->bi_dram[0].size = get_ram_size((volatile void *)PHYS_SDRAM_1,
 			PHYS_SDRAM_1_SIZE);
 #if CONFIG_NR_DRAM_BANKS > 1
 	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
 	gd->bd->bi_dram[1].size = get_ram_size((volatile void *)PHYS_SDRAM_2,
 			PHYS_SDRAM_2_SIZE);
-#else
-
 #endif
 }
board/keymile/km_arm/km_arm.c +11 -2
index d7cbd7a..b6c5038 100644
@@ -225,16 +225,25 @@ U_BOOT_CMD(
 	);
 #endif
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	/* Fix this */
+	gd->ram_size = get_ram_size((volatile void *)kw_sdram_bar(0),
+				kw_sdram_bs(0));
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	int i;
 
 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
 		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
 		gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i),
 						       kw_sdram_bs(i));
 	}
-	return 0;
 }
 
 /* Configure and enable MV88E1118 PHY */
board/logicpd/imx27lite/config.mk +1 -1
index a2e7768..2f9c4e6 100644
@@ -1 +1 @@
-TEXT_BASE = 0xA7F00000
+TEXT_BASE = 0xc0000000
board/logicpd/imx27lite/imx27lite.c +9 -6
index 4427415..f6a6385 100644
@@ -66,19 +66,22 @@ int board_init (void)
 
 int dram_init (void)
 {
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
+	return 0;
+}
 
-#if CONFIG_NR_DRAM_BANKS > 0
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = get_ram_size((volatile void *)PHYS_SDRAM_1,
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
 			PHYS_SDRAM_1_SIZE);
-#endif
 #if CONFIG_NR_DRAM_BANKS > 1
 	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
 	gd->bd->bi_dram[1].size = get_ram_size((volatile void *)PHYS_SDRAM_2,
 			PHYS_SDRAM_2_SIZE);
 #endif
-
-	return 0;
 }
 
 int checkboard(void)
board/ronetix/pm9261/pm9261.c +10 -3
index 53d8c48..a317ebc 100644
@@ -279,13 +279,20 @@ int board_eth_init(bd_t *bis)
 }
 #endif
 
-int dram_init(void)
+int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/ronetix/pm9263/pm9263.c +10 -3
index e41c84c..a88a038 100644
@@ -377,13 +377,20 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/ronetix/pm9g45/pm9g45.c +10 -3
index 3b4d9a3..23bc6a2 100644
@@ -158,13 +158,20 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_RESET_PHY_R
 void reset_phy(void)
 {
board/st/nhk8815/nhk8815.c +9 -2
index faef810..62cde13 100644
@@ -80,7 +80,15 @@ int board_late_init(void)
 	return 0;
 }
 
-int dram_init(void)
+int dram_init (void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
+	return 0;
+}
+
+void dram_init_banksize (void)
 {
 	/* set dram bank start addr and size */
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;

@@ -88,7 +96,6 @@ int dram_init(void)
 
 	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
 	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-	return 0;
 }
 
 #ifdef CONFIG_CMD_NET
board/ti/omap1510inn/config.mk +2 -1
index 9cd7424..cfccaa1 100644
@@ -22,4 +22,5 @@
 #
 
 
-TEXT_BASE = 0x11080000
+#TEXT_BASE = 0x11080000
+TEXT_BASE = 0x00000000
board/ti/omap1510inn/omap1510innovator.c +9 -4
index 2cb6062..7859bbf 100644
@@ -120,15 +120,20 @@ static void ether__init (void)
 	udelay (3);
 }
 
-
 int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 #ifdef CONFIG_CMD_NET
 int board_eth_init(bd_t *bis)
 {
board/ti/omap1610inn/config.mk +2 -1
index 1c5b7b5..826601c 100644
@@ -23,4 +23,5 @@
 #
 
 
-TEXT_BASE = 0x11080000
+#TEXT_BASE = 0x11080000
+TEXT_BASE = 0x00000000
board/ti/omap1610inn/omap1610innovator.c +9 -3
index 44818bb..1b0f7eb 100644
@@ -154,12 +154,18 @@ void ether__init (void)
 ******************************/
 int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 /******************************************************
  Routine: set_muxconf_regs
  Description: Setting up the configuration Mux registers
board/ti/omap5912osk/omap5912osk.c +9 -3
index cbf451b..a3f7457 100644
@@ -137,12 +137,18 @@ void ether__init (void)
 ******************************/
 int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 /******************************************************
  Routine: set_muxconf_regs
  Description: Setting up the configuration Mux registers
board/ti/omap730p2/omap730p2.c +9 -3
index 954ced5..b4c8b98 100644
@@ -181,12 +181,18 @@ void ether__init (void)
 ******************************/
 int dram_init (void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
 	return 0;
 }
 
+void dram_init_banksize (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
 /******************************************************
  Routine: set_muxconf_regs
  Description: Setting up the configuration Mux registers
include/configs/at91cap9adk.h +4 -0
index 44c2870..fcc2efe 100644
@@ -217,4 +217,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/at91sam9260ek.h +4 -0
index b89242b..9533f84 100644
@@ -221,4 +221,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/at91sam9261ek.h +4 -0
index df8181b..f8594a3 100644
@@ -239,4 +239,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/at91sam9263ek.h +4 -0
index 5cafa1e..5e2208e 100644
@@ -349,4 +349,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/at91sam9m10g45ek.h +4 -0
index 44c5496..f94da3a 100644
@@ -225,4 +225,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/at91sam9rlek.h +4 -0
index e8fcd66..18d1aa7 100644
@@ -184,4 +184,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/cpu9260.h +4 -0
index fb6f79a..1091293 100644
@@ -453,4 +453,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/da830evm.h +5 -0
index 160ece2..cec7da4 100644
@@ -281,4 +281,9 @@
 	"mtdparts=davinci_nand.1:" PART_BOOT PART_PARAMS PART_KERNEL PART_REST
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0xc0000000 /* should be DAVINCI_DDR_EMIF_DATA_BASE */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */
include/configs/da850evm.h +4 -0
index 357715d..e14817b 100644
@@ -137,4 +137,8 @@
 #undef CONFIG_CMD_ENV
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0xc0000000
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_dm355evm.h +4 -0
index 37011c0..f322664 100644
@@ -191,4 +191,8 @@
 #define MTDPARTS_DEFAULT	\
 	"mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_dm355leopard.h +4 -0
index e09fb75..de11948 100644
@@ -159,4 +159,8 @@
 #define MTDPARTS_DEFAULT	\
 	"mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_dm365evm.h +4 -0
index 2c3d88d..5036b34 100644
@@ -217,4 +217,8 @@
 #define MTDPARTS_DEFAULT	\
 	"mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_dm6467evm.h +4 -0
index ddc5990..c9e77ff 100644
@@ -128,4 +128,8 @@
 #define CONFIG_CMD_NAND
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_dvevm.h +6 -0
index aab2afa..e9c8b0e 100644
@@ -161,6 +161,7 @@
 #define PHYS_FLASH_SIZE		0x2000000	/* Flash size 32MB	 */
 #define CONFIG_SYS_MAX_FLASH_SECT	(PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
 #define CONFIG_ENV_SECT_SIZE	CONFIG_SYS_FLASH_SECT_SZ	/* Env sector Size */
+#define CONFIG_ENV_SIZE		CONFIG_SYS_FLASH_SECT_SZ	/* Fix this */
 #endif
 /*==============================*/
 /* U-Boot general configuration */

@@ -240,4 +241,9 @@
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
 #endif
+
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_schmoogie.h +5 -0
index 875dda4..e267266 100644
@@ -157,4 +157,9 @@
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
 #endif
+
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_sffsdr.h +5 -0
index f4e17f8..0007cf8 100644
@@ -150,4 +150,9 @@
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
 #endif
+
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/davinci_sonata.h +6 -0
index 4c01844..4a6e3b3 100644
@@ -148,6 +148,7 @@
 #define PHYS_FLASH_SIZE		0x2000000	/* Flash size 32MB	 */
 #define CONFIG_SYS_MAX_FLASH_SECT	(PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
 #define CONFIG_ENV_SECT_SIZE	CONFIG_SYS_FLASH_SECT_SZ	/* Env sector Size */
+#define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE	/* Fix this */
 #endif
 /*==============================*/
 /* U-Boot general configuration */

@@ -209,4 +210,9 @@
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
 #endif
+
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/edminiv2.h +4 -0
index 055931c..8aa7f83 100644
@@ -180,4 +180,8 @@
 #define CONFIG_SYS_RESET_ADDRESS	0xffff0000
 #define CONFIG_SYS_MAXARGS		16
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR		(0x00000000 + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* _CONFIG_EDMINIV2_H */
include/configs/guruplug.h +4 -0
index eb3fa57..3995a3e 100644
@@ -195,4 +195,8 @@
 
 #define CONFIG_SYS_ALT_MEMTEST
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR		(0x00000000 + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* _CONFIG_GURUPLUG_H */
include/configs/imx27lite-common.h +4 -0
index 1da8602..ddbcf28 100644
@@ -234,4 +234,8 @@
 	"mtdids=" MTDIDS_DEFAULT "\0"					\
 	"mtdparts=" MTDPARTS_DEFAULT "\0"				\
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __IMX27LITE_COMMON_CONFIG_H */
include/configs/km_arm.h +4 -0
index 6519c90..198fc59 100644
@@ -188,4 +188,8 @@ int get_scl (void);
 #undef	CONFIG_JFFS2_CMDLINE
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR		(0x00000000 + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* _CONFIG_KM_ARM_H */
include/configs/meesc.h +4 -0
index e085f4a..6c71b01 100644
@@ -180,4 +180,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/mv88f6281gtw_ge.h +4 -0
index 9ef03a6..e4a1703 100644
@@ -197,4 +197,8 @@
 #define CONFIG_SUPPORT_VFAT
 #endif /* CONFIG_CMD_USB */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR		(0x00000000 + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* _CONFIG_MV88F6281GTW_GE_H */
include/configs/nhk8815.h +4 -0
index 2b640dc..98a1d56 100644
@@ -197,4 +197,8 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	512
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* __CONFIG_H */
include/configs/ns9750dev.h +4 -0
index 79dcd64..34386bc 100644
@@ -195,4 +195,8 @@ extern void __led_set(led_id_t mask, int state);
 
 #endif /* CONFIG_STATUS_LED */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif	/* __CONFIG_H */
include/configs/omap1610h2.h +4 -0
index 0bbb5b3..2bd352a 100644
@@ -190,4 +190,8 @@ extern unsigned long omap_flash_base;		/* set in flash__init */
 #define CONFIG_ENV_SIZE	0x20000	/* Total Size of Environment Sector */
 #define CONFIG_ENV_OFFSET	0x20000	/* environment starts here */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif							/* __CONFIG_H */
include/configs/omap1610inn.h +4 -0
index 832dd42..0734957 100644
@@ -195,4 +195,8 @@ extern unsigned long omap_flash_base;		/* set in flash__init */
 #define CONFIG_ENV_SIZE	0x20000	/* Total Size of Environment Sector */
 #define CONFIG_ENV_OFFSET	0x20000	/* environment starts here  */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif							/* __CONFIG_H */
include/configs/omap5912osk.h +4 -0
index bc660e3..f472798 100644
@@ -200,4 +200,8 @@
 #define CONFIG_ENV_SIZE	0x20000	/* Total Size of Environment Sector */
 #define CONFIG_ENV_OFFSET	0x20000	/* environment starts here  */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif							/* __CONFIG_H */
include/configs/omap730p2.h +4 -0
index a6a8a02..f011427 100644
@@ -201,4 +201,8 @@
 #define CONFIG_ENV_SIZE		   0x20000	  /* Total Size of Environment Sector */
 #define CONFIG_ENV_OFFSET		   0x20000	  /* environment starts here  */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif	  /* ! __CONFIG_H */
include/configs/openrd_base.h +4 -0
index 52fa73d..ae6a9cd 100644
@@ -216,4 +216,8 @@
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_LZO
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR		(0x00000000 + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* _CONFIG_OPENRD_BASE_H */
include/configs/otc570.h +4 -0
index fb0f576..ee14bd8 100644
@@ -242,4 +242,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/pm9261.h +4 -0
index a0b00e9..73e0ba9 100644
@@ -378,4 +378,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/pm9263.h +4 -0
index 9735e6a..6ea54d8 100644
@@ -409,4 +409,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/pm9g45.h +4 -0
index 690f119..a3e147a 100644
@@ -183,4 +183,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/rd6281a.h +4 -0
index 5857301..0ba436a 100644
@@ -195,4 +195,8 @@
 #define CONFIG_SUPPORT_VFAT
 #endif /* CONFIG_CMD_USB */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR		(0x00000000 + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* _CONFIG_RD6281A_H */
include/configs/sbc35_a9g20.h +4 -0
index b9f27cc..5aa4810 100644
@@ -194,4 +194,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/sheevaplug.h +4 -0
index c5de86e..0537c8f 100644
@@ -209,4 +209,8 @@
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_LZO
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_INIT_SP_ADDR		(0x00000000 + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif /* _CONFIG_SHEEVAPLUG_H */
include/configs/tny_a9260.h +4 -0
index 5af2af3..1fb0846 100644
@@ -172,4 +172,8 @@
 #error CONFIG_USE_IRQ not supported
 #endif
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif
include/configs/versatile.h +4 -0
index 4273b84..cb763ec 100644
@@ -232,4 +232,8 @@
 #define CONFIG_SYS_FLASH_PROTECTION	/* The devices have real protection */
 #define CONFIG_SYS_FLASH_EMPTY_INFO	/* flinfo indicates empty blocks */
 
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					CONFIG_SYS_GBL_DATA_SIZE)
 #endif	/* __CONFIG_H */
Signature · 5 lines
1.6.2.5

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany