Skip to contentSkip to conversation

Add disk support to orion5x and edminiv2

PATCH Superseded Albert Aribaud 3 participants 14 messages Aug 7, 2010 – Aug 12, 2010

Subsystems (3)
Arm (32-bit) PowerPC Block layer
lore
Share & tools
lore

Albert Aribaud

author
#0 lore raw

v8 cover Add disk support to orion5x and edminiv2

Patchset history:

V1: Initial 4-patch set -- not cleanly submitted (does
not appear on gmane for instance) and contained some unrelated changes.

V2: Slimmed down to 3 patches and removed unrelated
changes.

V3: Back to 4 patches (cmd_ide improvement, driver addition,

    cmd_ide support for orion, edminiv2 support for sata);
    made initialization code reuseable as a block driver ;
    moved to C structures; commented some constants.

V4: Reordered objects alphabetically in drivers/block/Makefile.
Shortened mv_sata to mvsata.
Removed volatile qualifier in mvsata port structure. Moved port pointer definition from SoC to board code. Removed unrelated changes.

V5: Fixed typo in mvsata_ide driver (IMP, should have been IPM).

V6: Fixed case in ide register struct.
Fixed warning in deminiv2.c
Put IDE configuration under condition.

V7: Reworked the initialization logic to poll status register.
Moved initialization from board code to driver code. Removed driver header file and moved its content to driver code. Moved CONFIG_IDE_PREINIT from SoC to board config file.

V8: Separated V7's patch 2 in two independant patches.
Fixed typo in struct names within ide_preinit().

The V8 patches have been run through checkpatch.pl --no-tree with no errors or warnings, and have been tested on an ED Mini V2.

Albert Aribaud (5):
ide: add configuration CONFIG_IDE_SWAP_IO
ide: reorder object files alphabetically
ide: add mvsata_ide driver
cmd_ide: add support for orion5x
edminiv2: add mvsata_ide and cmd_ide support

 arch/arm/include/asm/arch-orion5x/orion5x.h |    3 +
 arch/powerpc/include/asm/config.h           |    3 +
 common/cmd_ide.c                            |   23 +++--
 doc/README.PXA_CF                           |    8 ++
 drivers/block/Makefile                      |    7 +-
 drivers/block/mvsata_ide.c                  |  140 +++++++++++++++++++++++++++
 include/configs/ap325rxa.h                  |    1 +
 include/configs/edminiv2.h                  |   34 ++++++-
 include/configs/ms7720se.h                  |    1 +
 include/configs/r2dplus.h                   |    1 +
 include/configs/r7780mp.h                   |    1 +
 11 files changed, 209 insertions(+), 13 deletions(-)
 create mode 100644 drivers/block/mvsata_ide.c
author
#1 lore raw

PATCH v8 1/5 ide: add configuration CONFIG_IDE_SWAP_IO

This configuration option replaces a complex conditional in cmd_ide.c with an explicit define to be added to SoC or board configs.

Signed-off-by Albert Aribaud <[email protected]>
---
 arch/powerpc/include/asm/config.h |    3 +++
 common/cmd_ide.c                  |   18 +++++++++---------
 doc/README.PXA_CF                 |    8 ++++++++
 include/configs/ap325rxa.h        |    1 +
 include/configs/ms7720se.h        |    1 +
 include/configs/r2dplus.h         |    1 +
 include/configs/r7780mp.h         |    1 +
 7 files changed, 24 insertions(+), 9 deletions(-)
arch/powerpc/include/asm/config.h +3 -0
index f70699d..d098657 100644
@@ -95,4 +95,7 @@
 #define CONFIG_FSL_LBC
 #endif
 
+/* All PPC boards must swap IDE bytes */
+#define CONFIG_IDE_SWAP_IO
+
 #endif /* _ASM_CONFIG_H_ */
common/cmd_ide.c +9 -9
index c0fb88d..d423e53 100644
@@ -847,7 +847,7 @@ input_swap_data(int dev, ulong *sect_buf, int words)
 #endif	/* __LITTLE_ENDIAN || CONFIG_AU1X00 */
 
 
-#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA) || defined(CONFIG_SH)
+#if defined(CONFIG_IDE_SWAP_IO)
 static void
 output_data(int dev, ulong *sect_buf, int words)
 {

@@ -891,15 +891,15 @@ output_data(int dev, ulong *sect_buf, int words)
 	}
 #endif
 }
-#else	/* ! __PPC__ */
+#else	/* ! CONFIG_IDE_SWAP_IO */
 static void
 output_data(int dev, ulong *sect_buf, int words)
 {
 	outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words<<1);
 }
-#endif	/* __PPC__ */
+#endif	/* CONFIG_IDE_SWAP_IO */
 
-#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA) || defined(CONFIG_SH)
+#if defined(CONFIG_IDE_SWAP_IO)
 static void
 input_data(int dev, ulong *sect_buf, int words)
 {

@@ -949,14 +949,14 @@ input_data(int dev, ulong *sect_buf, int words)
 	}
 #endif
 }
-#else	/* ! __PPC__ */
+#else	/* ! CONFIG_IDE_SWAP_IO */
 static void
 input_data(int dev, ulong *sect_buf, int words)
 {
 	insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words << 1);
 }
 
-#endif	/* __PPC__ */
+#endif	/* CONFIG_IDE_SWAP_IO */
 
 /* -------------------------------------------------------------------------
  */

@@ -1573,7 +1573,7 @@ int ide_device_present(int dev)
  * ATAPI Support
  */
 
-#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
+#if defined(CONFIG_IDE_SWAP_IO)
 /* since ATAPI may use commands with not 4 bytes alligned length
  * we have our own transfer functions, 2 bytes alligned */
 static void

@@ -1640,7 +1640,7 @@ input_data_shorts(int dev, ushort *sect_buf, int shorts)
 #endif
 }
 
-#else	/* ! __PPC__ */
+#else	/* ! CONFIG_IDE_SWAP_IO */
 static void
 output_data_shorts(int dev, ushort *sect_buf, int shorts)
 {

@@ -1653,7 +1653,7 @@ input_data_shorts(int dev, ushort *sect_buf, int shorts)
 	insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, shorts);
 }
 
-#endif	/* __PPC__ */
+#endif	/* CONFIG_IDE_SWAP_IO */
 
 /*
  * Wait until (Status & mask) == res, or timeout (in ms)
doc/README.PXA_CF +8 -0
index 6a0f236..1d76b32 100644
@@ -6,6 +6,14 @@ follow the connections of the standard lubbock. Anyway just the block
 marked memory configuration should be touched since the other parameters
 are imposed by the PXA architecture.
 
+EDIT 2010-07-01: in common/cmd_ide.c, having CONFIG_PXA_PCMCIA defined
+would cause looping on inw()/outw() rather than using insw()/outsw(),
+thus making sure IDE / ATA bytes are properly swapped. This behaviour
+is now controlled by CONFIG_IDE_SWAP_IO, therefore PXA boards with
+PCMCIA should #define CONFIG_IDE_SWAP_IO.
+
+#define CONFIG_IDE_SWAP_IO
+
 #define CONFIG_PXA_PCMCIA 1
 #define CONFIG_PXA_IDE 1
include/configs/ap325rxa.h +1 -0
index 70dd47e..80a5797 100644
@@ -138,6 +138,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x200	/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0x200	/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x210	/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 /* if you use all NOR Flash , you change dip-switch. Please see Manual. */
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
include/configs/ms7720se.h +1 -0
index ba0a3f8..0ea3527 100644
@@ -122,5 +122,6 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0		/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0		/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x200		/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 #endif	/* __MS7720SE_H */
include/configs/r2dplus.h +1 -0
index 8931b97..955f3ff 100644
@@ -96,6 +96,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x1000	/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0x1000	/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x800	/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 /*
  * SuperH PCI Bridge Configration
include/configs/r7780mp.h +1 -0
index 71c570e..3afe93a 100644
@@ -171,6 +171,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET     0x1000          /* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET      0x1000          /* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET      0x800           /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 #endif /* CONFIG_CMD_IDE */
 
 #endif /* __R7780RP_H */
Signature · 1 line
1.6.4.4
author
#2 lore raw

PATCH v8 2/5 ide: reorder object files alphabetically

Signed-off-by Albert Aribaud <[email protected]>
---
 drivers/block/Makefile |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)
drivers/block/Makefile +3 -3
index 3f6ad5c..3bab1e4 100644
@@ -25,15 +25,15 @@ include $(TOPDIR)/config.mk
 
 LIB	:= $(obj)libblock.a
 
+COBJS-$(CONFIG_SCSI_AHCI) += ahci.o
 COBJS-$(CONFIG_ATA_PIIX) += ata_piix.o
-COBJS-$(CONFIG_CMD_MG_DISK) += mg_disk.o
 COBJS-$(CONFIG_FSL_SATA) += fsl_sata.o
-COBJS-$(CONFIG_IDE_SIL680) += sil680.o
 COBJS-$(CONFIG_LIBATA) += libata.o
+COBJS-$(CONFIG_CMD_MG_DISK) += mg_disk.o
 COBJS-$(CONFIG_PATA_BFIN) += pata_bfin.o
 COBJS-$(CONFIG_SATA_DWC) += sata_dwc.o
 COBJS-$(CONFIG_SATA_SIL3114) += sata_sil3114.o
-COBJS-$(CONFIG_SCSI_AHCI) += ahci.o
+COBJS-$(CONFIG_IDE_SIL680) += sil680.o
 COBJS-$(CONFIG_SCSI_SYM53C8XX) += sym53c8xx.o
 COBJS-$(CONFIG_SYSTEMACE) += systemace.o
Signature · 1 line
1.6.4.4
author
#3 lore raw

PATCH v8 3/5 ide: add mvsata_ide driver

This driver only provides initialization code; actual driving is done by cmd_ide.c using the ATA compatibility mode of the Marvell SATAHC controller.

Signed-off-by Albert Aribaud <[email protected]>
---
 drivers/block/Makefile     |    1 +
 drivers/block/mvsata_ide.c |  140 ++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 141 insertions(+), 0 deletions(-)
 create mode 100644 drivers/block/mvsata_ide.c
drivers/block/Makefile +1 -0
index 3bab1e4..64dcf4e 100644
@@ -30,6 +30,7 @@ COBJS-$(CONFIG_ATA_PIIX) += ata_piix.o
 COBJS-$(CONFIG_FSL_SATA) += fsl_sata.o
 COBJS-$(CONFIG_LIBATA) += libata.o
 COBJS-$(CONFIG_CMD_MG_DISK) += mg_disk.o
+COBJS-$(CONFIG_MVSATA_IDE) += mvsata_ide.o
 COBJS-$(CONFIG_PATA_BFIN) += pata_bfin.o
 COBJS-$(CONFIG_SATA_DWC) += sata_dwc.o
 COBJS-$(CONFIG_SATA_SIL3114) += sata_sil3114.o
drivers/block/mvsata_ide.c new file +140 -0

140 lines not on this page · raw message

Signature · 1 line
1.6.4.4
author
#4 lore raw

PATCH v8 4/5 cmd_ide: add support for orion5x

Add MVSATAHC definitions to orion5x.
Add support for orion5x in cmd_ide.

Signed-off-by Albert Aribaud <[email protected]>
---
 arch/arm/include/asm/arch-orion5x/orion5x.h |    3 +++
 common/cmd_ide.c                            |    5 +++++
 2 files changed, 8 insertions(+), 0 deletions(-)
arch/arm/include/asm/arch-orion5x/orion5x.h +3 -0
index d257b66..e3d3f76 100644
@@ -55,6 +55,9 @@
 #define ORION5X_USB20_PORT0_BASE		(ORION5X_REGISTER(0x50000))
 #define ORION5X_USB20_PORT1_BASE		(ORION5X_REGISTER(0xA0000))
 #define ORION5X_EGIGA_BASE			(ORION5X_REGISTER(0x72000))
+#define ORION5X_SATA_BASE			(ORION5X_REGISTER(0x80000))
+#define ORION5X_SATA_PORT0_OFFSET		0x2000
+#define ORION5X_SATA_PORT1_OFFSET		0x4000
 
 /* Orion5x GbE controller has a single port */
 #define MAX_MVGBE_DEVS	1
common/cmd_ide.c +5 -0
index d423e53..b23db3f 100644
@@ -25,6 +25,7 @@
 /*
  * IDE support
  */
+
 #include <common.h>
 #include <config.h>
 #include <watchdog.h>

@@ -45,6 +46,10 @@
 #include <mpc5xxx.h>
 #endif
 
+#ifdef CONFIG_ORION5X
+#include <asm/arch/orion5x.h>
+#endif
+
 #include <ide.h>
 #include <ata.h>
Signature · 1 line
1.6.4.4
author
#5 lore raw

PATCH v8 5/5 edminiv2: add mvsata_ide and cmd_ide support

Add mvsata_ide and cmd_ide configuration in edminiv2 config

Signed-off-by Albert Aribaud <[email protected]>
---
 include/configs/edminiv2.h |   34 +++++++++++++++++++++++++++++++++-
 1 files changed, 33 insertions(+), 1 deletions(-)
include/configs/edminiv2.h +33 -1
index 055931c..57dd165 100644
@@ -60,7 +60,7 @@
 
 #define ORION5X_MPP0_7		0x00000003
 #define ORION5X_MPP8_15		0x55550000
-#define ORION5X_MPP16_23	0x00000000
+#define ORION5X_MPP16_23	0x00005555
 
 /*
  * Board-specific values for Orion5x GPIO low level init:

@@ -131,6 +131,7 @@
  * Commands configuration - using default command set for now
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_IDE
 
 /*
  * Network

@@ -150,6 +151,37 @@
 #endif
 
 /*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET	ORION5X_SATA_PORT1_OFFSET
+/* end of IDE defines */
+#endif /* CMD_IDE */
+
+/*
  *  Environment variables configurations
  */
 #define CONFIG_ENV_IS_IN_FLASH		1
Signature · 1 line
1.6.4.4
#6 lore raw

PATCH v8 5/5 edminiv2: add mvsata_ide and cmd_ide support

Quoted 10 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, August 07, 2010 6:22 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] [PATCH V8 5/5] edminiv2: add mvsata_ide and cmd_ide support

Quoted 6 lines

Add mvsata_ide and cmd_ide configuration in edminiv2 config

Signed-off-by Albert Aribaud <[email protected]>
---
 include/configs/edminiv2.h |   34 +++++++++++++++++++++++++++++++++-
 1 files changed, 33 insertions(+), 1 deletions(-)

Applied to u-boot-marvell.git master branch

Regards..
Prafulla . .

#7 lore raw

PATCH v8 5/5 edminiv2: add mvsata_ide and cmd_ide support

In reply to Albert Aribaud

include/configs/edminiv2.h line 163

Quoted 8 lines · Albert Aribaud

Add mvsata_ide and cmd_ide configuration in edminiv2 config

Signed-off-by Albert Aribaud<[email protected]>

---

include/configs/edminiv2.h +3 -0
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1

Hi Albert,

I'm trying to get IDE to work with my DNS323, which uses both SATA ports, but am being unsuccessful.

It seems that there may be something incorrectly merged, perhaps:

$ git grep CONFIG_MVSATA_IDE_USE_PORT
include/configs/edminiv2.h:#define CONFIG_MVSATA_IDE_USE_PORT1
include/configs/openrd_base.h:#define CONFIG_MVSATA_IDE_USE_PORT1
$

i.e. CONFIG_MVSATA_IDE_USE_PORT1 is defined, but never used for anything.

Regards,

Rogan

#8 lore raw

PATCH v8 4/5 cmd_ide: add support for orion5x

In reply to Albert Aribaud
Quoted 9 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, August 07, 2010 6:22 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] [PATCH V8 4/5] cmd_ide: add support for orion5x

Quoted 8 lines

Add MVSATAHC definitions to orion5x.
Add support for orion5x in cmd_ide.

Signed-off-by Albert Aribaud <[email protected]>
---
 arch/arm/include/asm/arch-orion5x/orion5x.h |    3 +++
 common/cmd_ide.c                            |    5 +++++
 2 files changed, 8 insertions(+), 0 deletions(-)

Applied to u-boot-marvell.git master branch

Regards..
Prafulla . .

#9 lore raw

PATCH v8 3/5 ide: add mvsata_ide driver

In reply to Albert Aribaud
Quoted 13 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, August 07, 2010 6:22 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] [PATCH V8 3/5] ide: add mvsata_ide driver

This driver only provides initialization code; actual driving is done by cmd_ide.c using the ATA compatibility mode of the Marvell SATAHC controller.

Quoted 7 lines
Signed-off-by Albert Aribaud <[email protected]>
---
 drivers/block/Makefile     |    1 +
 drivers/block/mvsata_ide.c |  140 
++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 141 insertions(+), 0 deletions(-)
 create mode 100644 drivers/block/mvsata_ide.c

Applied to u-boot-marvell.git

Regards..
Prafulla . .

#10 lore raw

PATCH v8 2/5 ide: reorder object files alphabetically

In reply to Albert Aribaud
Quoted 11 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, August 07, 2010 6:22 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] [PATCH V8 2/5] ide: reorder object files alphabetically

Quoted 5 lines
Signed-off-by Albert Aribaud <[email protected]>
---
 drivers/block/Makefile |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)

Applied to u-boot-marvell.git

Regards..
Prafulla . .

#11 lore raw

PATCH v8 1/5 ide: add configuration CONFIG_IDE_SWAP_IO

In reply to Albert Aribaud
Quoted 15 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, August 07, 2010 6:22 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] [PATCH V8 1/5] ide: add configuration CONFIG_IDE_SWAP_IO

This configuration option replaces a complex conditional in cmd_ide.c with an explicit define to be added to SoC or board configs.

Signed-off-by Albert Aribaud <[email protected]>
Quoted 9 lines
---
 arch/powerpc/include/asm/config.h |    3 +++
 common/cmd_ide.c                  |   18 +++++++++---------
 doc/README.PXA_CF                 |    8 ++++++++
 include/configs/ap325rxa.h        |    1 +
 include/configs/ms7720se.h        |    1 +
 include/configs/r2dplus.h         |    1 +
 include/configs/r7780mp.h         |    1 +
 7 files changed, 24 insertions(+), 9 deletions(-)

Applied to u-boot-marvell.git

Regards..
Prafulla . .

#12 lore raw

v8 cover Add disk support to orion5x and edminiv2

In reply to Albert Aribaud
Quoted 54 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, August 07, 2010 6:22 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] [PATCH V8 0/5] Add disk support to orion5x and edminiv2

Patchset history:

V1: Initial 4-patch set -- not cleanly submitted (does
not appear on gmane for instance) and contained some unrelated changes.

V2: Slimmed down to 3 patches and removed unrelated
changes.

V3: Back to 4 patches (cmd_ide improvement, driver addition,

    cmd_ide support for orion, edminiv2 support for sata);
    made initialization code reuseable as a block driver ;
    moved to C structures; commented some constants.

V4: Reordered objects alphabetically in drivers/block/Makefile.
Shortened mv_sata to mvsata.
Removed volatile qualifier in mvsata port structure. Moved port pointer definition from SoC to board code. Removed unrelated changes.

V5: Fixed typo in mvsata_ide driver (IMP, should have been IPM).

V6: Fixed case in ide register struct.
Fixed warning in deminiv2.c
Put IDE configuration under condition.

V7: Reworked the initialization logic to poll status register.
Moved initialization from board code to driver code. Removed driver header file and moved its content to driver code. Moved CONFIG_IDE_PREINIT from SoC to board config file.

V8: Separated V7's patch 2 in two independant patches.
Fixed typo in struct names within ide_preinit().

The V8 patches have been run through checkpatch.pl --no-tree with no errors or warnings, and have been tested on an ED Mini V2.

Albert Aribaud (5):
ide: add configuration CONFIG_IDE_SWAP_IO
ide: reorder object files alphabetically
ide: add mvsata_ide driver
cmd_ide: add support for orion5x
edminiv2: add mvsata_ide and cmd_ide support

Quoted 14 lines
 arch/arm/include/asm/arch-orion5x/orion5x.h |    3 +
 arch/powerpc/include/asm/config.h           |    3 +
 common/cmd_ide.c                            |   23 +++--
 doc/README.PXA_CF                           |    8 ++
 drivers/block/Makefile                      |    7 +-
 drivers/block/mvsata_ide.c                  |  140 
+++++++++++++++++++++++++++
 include/configs/ap325rxa.h                  |    1 +
 include/configs/edminiv2.h                  |   34 ++++++-
 include/configs/ms7720se.h                  |    1 +
 include/configs/r2dplus.h                   |    1 +
 include/configs/r7780mp.h                   |    1 +
 11 files changed, 209 insertions(+), 13 deletions(-)
 create mode 100644 drivers/block/mvsata_ide.c

Applied this patch series to u-boot-marvell.git master branch

Regards..
Prafulla . .

author
#13 lore raw

v8 cover Add disk support to orion5x and edminiv2

Le 09/08/2010 07:57, Prafulla Wadaskar a ?crit :

Quoted 8 lines
Quoted 7 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
Sent: Saturday, August 07, 2010 6:22 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] [PATCH V8 0/5] Add disk support to orion5x and edminiv2

Quoted 4 lines

Applied this patch series to u-boot-marvell.git master branch

Regards..
Prafulla . .

Thanks Prafulla!

Amicalement,

Signature · 1 line
Albert.