davinci: Initial support for MityDSP-L138/MityARM-1808
Subsystems (3)
PATCH v3 1/1 davinci: Initial support for MityDSP-L138/MityARM-1808
This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system on Module (SOM) under the machine name "mityomapl138". These SOMs are based on the da850 davinci CPU architecture. Information on these SOMs may be found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is included in this patch.
---
Changes since v2:
1) Remove defaulting this board from Kconfig.
2) Add MITYOMAPL138 board to da8xx_omapl_defconfig.
3) Fix tabs alignment per comment.
The new defconfig file was generated by:
make da8xx_omapl_defconfig
make menuconfig
select MITYOMAPL138 option
make savedefconfig
cp defconfig arch/arm/configs/da8xx_omapl_defconfig
I think the other 3 lines were a result of updated KConfig options in the current baseline.
arch/arm/configs/da8xx_omapl_defconfig | 4 +- arch/arm/mach-davinci/Kconfig | 8 + arch/arm/mach-davinci/Makefile | 1 + arch/arm/mach-davinci/board-mityomapl138.c | 220 +++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/uncompress.h | 1 + 5 files changed, 232 insertions(+), 2 deletions(-)
arch/arm/configs/da8xx_omapl_defconfig +2 -2
@@ -17,6 +17,7 @@ CONFIG_MODVERSIONS=y CONFIG_ARCH_DAVINCI=y CONFIG_ARCH_DAVINCI_DA830=y CONFIG_ARCH_DAVINCI_DA850=y +CONFIG_MACH_MITYOMAPL138=y CONFIG_DAVINCI_RESET_CLOCKS=y CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y
@@ -73,6 +74,7 @@ CONFIG_SERIO_LIBPS2=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=3 +CONFIG_SERIAL_8250_RUNTIME_UARTS=3 CONFIG_I2C=y CONFIG_I2C_CHARDEV=y CONFIG_I2C_DAVINCI=y
@@ -83,7 +85,6 @@ CONFIG_REGULATOR_DUMMY=y CONFIG_REGULATOR_TPS6507X=y CONFIG_FB=y CONFIG_FB_DA8XX=y -# CONFIG_VGA_CONSOLE is not set CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_LOGO=y CONFIG_SOUND=m
@@ -95,7 +96,6 @@ CONFIG_SND_DAVINCI_SOC=m CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y CONFIG_XFS_FS=m -CONFIG_INOTIFY=y CONFIG_AUTOFS4_FS=m CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y
arch/arm/mach-davinci/Kconfig +8 -0
@@ -185,6 +185,14 @@ config MACH_TNETV107X help Say Y here to select the TI TNETV107X Evaluation Module. +config MACH_MITYOMAPL138 + bool "Critical Link MityDSP-L138/MityARM-1808 SoM" + depends on ARCH_DAVINCI_DA850 + help + Say Y here to select the Critical Link MityDSP-L138/MityARM-1808 + System on Module. Information on this SoM may be found at + http://www.mitydsp.com + config DAVINCI_MUX bool "DAVINCI multiplexing support" depends on ARCH_DAVINCI
arch/arm/mach-davinci/Makefile +1 -0
@@ -33,6 +33,7 @@ obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o +obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o # Power Management obj-$(CONFIG_CPU_FREQ) += cpufreq.o
arch/arm/mach-davinci/board-mityomapl138.c new file +220 -0
220 lines not on this page · raw message
arch/arm/mach-davinci/include/mach/uncompress.h +1 -0
@@ -88,6 +88,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)/* DA8xx boards */ DEBUG_LL_DA8XX (davinci_da830_evm,2 );DEBUG_LL_DA8XX (davinci_da850_evm,2 ); +DEBUG_LL_DA8XX (mityomapl138,1 );/* TNETV107x boards */ DEBUG_LL_TNETV107X (tnetv107x,1 );
PATCH v3 1/1 davinci: Initial support for MityDSP-L138/MityARM-1808
Hello.
Quoted 9 lines · Michael Williamson
This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system on Module (SOM) under the machine name "mityomapl138". These SOMs are based on the da850 davinci CPU architecture. Information on these SOMs may be found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is included in this patch.
Signed-off-by Michael Williamson <[email protected]>
[...]
Quoted 6 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +0
-0@@ -0,0 +1,220 @@
[...]
Quoted 13 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +13
-0+static const short mityomap_mii_pins[] = { +DA850_MII_TXEN ,DA850_MII_TXCLK ,DA850_MII_COL ,DA850_MII_TXD_3 , +DA850_MII_TXD_2 ,DA850_MII_TXD_1 ,DA850_MII_TXD_0 ,DA850_MII_RXER , +DA850_MII_CRS ,DA850_MII_RXCLK ,DA850_MII_RXDV ,DA850_MII_RXD_3 , +DA850_MII_RXD_2 ,DA850_MII_RXD_1 ,DA850_MII_RXD_0 ,DA850_MDIO_CLK , +DA850_MDIO_D , +-1 +}; + +static const short mityomap_rmii_pins[] = { +DA850_RMII_TXD_0 ,DA850_RMII_TXD_1 ,DA850_RMII_TXEN , +DA850_RMII_CRS_DV ,DA850_RMII_RXD_0 ,DA850_RMII_RXD_1 , +DA850_RMII_RXER ,DA850_RMII_MHZ_50_CLK ,DA850_MDIO_CLK ,
arch/arm/mach-davinci/board-mityomapl138.c line 114
Quoted 10 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +10
-0+DA850_MDIO_D , + -1 +}; + +static void __init mityomapl138_config_emac (void ) +{ +void __iomem *cfg_chip3_base; +int ret; +u32 val; +struct davinci_soc_info *soc_info = &davinci_soc_info;
Should be an empty line here...
arch/arm/mach-davinci/board-mityomapl138.c line 120
Quoted 6 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +6
-0+ soc_info->emac_pdata->rmii_en =0 ;/* hardcoded for now */ + + cfg_chip3_base =DA8XX_SYSCFG0_VIRT (DA8XX_CFGCHIP3_REG ); + val =__raw_readl (cfg_chip3_base); + +if (soc_info->emac_pdata->rmii_en) {
If it's hard coded to 0, why handle the other case?
arch/arm/mach-davinci/board-mityomapl138.c line 128
Quoted 8 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +8
-0+ val |=BIT (8 ); + ret =davinci_cfg_reg_list (mityomap_rmii_pins); +pr_info ("RMII PHY configured\n" ); + }else { + val &= ~BIT (8 ); + ret =davinci_cfg_reg_list (mityomap_mii_pins); +pr_info ("MII PHY configured\n" ); + }
WBR, Sergei
PATCH v3 1/1 davinci: Initial support for MityDSP-L138/MityARM-1808
Quoted 40 lines · Sergei Shtylyov
Hello.
Quoted 9 lines · Michael Williamson
This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system on Module (SOM) under the machine name "mityomapl138". These SOMs are based on the da850 davinci CPU architecture. Information on these SOMs may be found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is included in this patch.
Signed-off-by Michael Williamson <[email protected]>[...]
Quoted 6 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +0
-0@@ -0,0 +1,220 @@[...]
Quoted 17 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +17
-0+static const short mityomap_mii_pins[] = { +DA850_MII_TXEN ,DA850_MII_TXCLK ,DA850_MII_COL ,DA850_MII_TXD_3 , +DA850_MII_TXD_2 ,DA850_MII_TXD_1 ,DA850_MII_TXD_0 ,DA850_MII_RXER , +DA850_MII_CRS ,DA850_MII_RXCLK ,DA850_MII_RXDV ,DA850_MII_RXD_3 , +DA850_MII_RXD_2 ,DA850_MII_RXD_1 ,DA850_MII_RXD_0 ,DA850_MDIO_CLK , +DA850_MDIO_D , +-1 +}; + +static const short mityomap_rmii_pins[] = { +DA850_RMII_TXD_0 ,DA850_RMII_TXD_1 ,DA850_RMII_TXEN , +DA850_RMII_CRS_DV ,DA850_RMII_RXD_0 ,DA850_RMII_RXD_1 , +DA850_RMII_RXER ,DA850_RMII_MHZ_50_CLK ,DA850_MDIO_CLK , +DA850_MDIO_D , +-1 +}; +
Quoted 8 lines
arch/arm/mach-davinci/board-mityomapl138.c line 114
Quoted 6 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +6
-0+static void __init mityomapl138_config_emac (void ) +{ +void __iomem *cfg_chip3_base; +int ret; +u32 val; +struct davinci_soc_info *soc_info = &davinci_soc_info;Should be an empty line here...
I'll add this before pushing.
Quoted 8 lines
arch/arm/mach-davinci/board-mityomapl138.c line 120
Quoted 6 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +6
-0+ soc_info->emac_pdata->rmii_en =0 ;/* hardcoded for now */ + + cfg_chip3_base =DA8XX_SYSCFG0_VIRT (DA8XX_CFGCHIP3_REG ); + val =__raw_readl (cfg_chip3_base); + +if (soc_info->emac_pdata->rmii_en) {If it's hard coded to 0, why handle the other case?
He's planning to add support for the other options in subsequent patches, so I'm OK with leaving this as is.
Quoted 10 lines
arch/arm/mach-davinci/board-mityomapl138.c line 128
Quoted 8 lines
arch/arm/mach-davinci/board-mityomapl138.c new file +8
-0+ val |=BIT (8 ); + ret =davinci_cfg_reg_list (mityomap_rmii_pins); +pr_info ("RMII PHY configured\n" ); + }else { + val &= ~BIT (8 ); + ret =davinci_cfg_reg_list (mityomap_mii_pins); +pr_info ("MII PHY configured\n" ); + }WBR, Sergei
Kevin
PATCH v3 1/1 davinci: Initial support for MityDSP-L138/MityARM-1808
In reply to Michael WilliamsonQuoted 9 lines · Michael Williamson
This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system on Module (SOM) under the machine name "mityomapl138". These SOMs are based on the da850 davinci CPU architecture. Information on these SOMs may be found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is included in this patch.
Signed-off-by Michael Williamson <[email protected]>
Thanks, applying and queueing for 2.6.37 (with one minor change below...)
Quoted 13 lines
---
Changes since v2:
1) Remove defaulting this board fromKconfig.
2) Add MITYOMAPL138 board toda8xx_omapl_defconfig.
3) Fix tabs alignment per comment.The new defconfig file was generated by:
makeda8xx_omapl_defconfig
make menuconfig
select MITYOMAPL138 option
make savedefconfig
cp defconfigarch/arm/configs/da8xx_omapl_defconfig
Quoted 2 lines
I think the other 3 lines were a result of updated KConfig options in the current baseline.
Yes, but to minimize unrelated defconfig diffs upstream, I'm going to remove the 3 unrelated ones when applying this patch.
Soon we will hopefully be getting rid of defconfigs all together, but until that is sorted out, we need to minimize diffs against defconfigs, especially ones that are not related to the patch.
Kevin