davinci: Add I2C0 devices to MityDSP-L138/MityARM-1808 platform
Subsystems (3)
PATCH 1/1 davinci: Add I2C0 devices to MityDSP-L138/MityARM-1808 platform
This patch adds the i2c0 bus and attached devices to the MityDSP-L138 and MityARM-1808 davinci SoM. Included is a TPS65023 voltage regulator needed for power management and a small 24c02 EPROM that contains factory configuration data.
---
This is based on 08f143b7cdbe9705f6856c2a63b6d3b14b5a8eee of davinci-linux tree.
arch/arm/mach-davinci/board-mityomapl138.c | 145 ++++++++++++++++++++++++++++ 1 files changed, 145 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-mityomapl138.c +145 -0
@@ -13,6 +13,8 @@#include <linux/console.h> #include <linux/platform_device.h> #include <linux/mtd/partitions.h> +#include <linux/regulator/machine.h> +#include <linux/i2c.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -25,6 +27,141 @@#define MITYOMAPL138_PHY_MASK 0x08/* hardcoded for now */ #define MITYOMAPL138_MDIO_FREQUENCY (2200000)/* PHY bus frequency */ +static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = { + .bus_freq =100 ,/* kHz */ + .bus_delay =0 ,/* usec */ +}; + +/* TPS65023 voltage regulator support */ +/* 1.2V Core */ +struct regulator_consumer_supply tps65023_dcdc1_consumers[] = { + { + .supply ="cvdd" , + }, +}; + +/* 1.8V */ +struct regulator_consumer_supply tps65023_dcdc2_consumers[] = { + { + .supply ="usb0_vdda18" , + }, + { + .supply ="usb1_vdda18" , + }, + { + .supply ="ddr_dvdd18" , + }, + { + .supply ="sata_vddr" , + }, +}; + +/* 1.2V */ +struct regulator_consumer_supply tps65023_dcdc3_consumers[] = { + { + .supply ="sata_vdd" , + }, + { + .supply ="usb_cvdd" , + }, + { + .supply ="pll0_vdda" , + }, + { + .supply ="pll1_vdda" , + }, +}; + +/* 1.8V Aux LDO, not used */ +struct regulator_consumer_supply tps65023_ldo1_consumers[] = { + { + .supply ="1.8v_aux" , + }, +}; + +/* FPGA VCC Aux (2.5 or 3.3) LDO */ +struct regulator_consumer_supply tps65023_ldo2_consumers[] = { + { + .supply ="vccaux" , + }, +}; + +struct regulator_init_data tps65023_regulator_data[] = { +/* dcdc1 */ + { + .constraints = { + .min_uV =1150000 , + .max_uV =1350000 , + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | +REGULATOR_CHANGE_STATUS ), + .boot_on =1 , + }, + .num_consumer_supplies =ARRAY_SIZE (tps65023_dcdc1_consumers), + .consumer_supplies = tps65023_dcdc1_consumers, + }, +/* dcdc2 */ + { + .constraints = { + .min_uV =1800000 , + .max_uV =1800000 , + .valid_ops_mask = (REGULATOR_CHANGE_STATUS ), + .boot_on =1 , + }, + .num_consumer_supplies =ARRAY_SIZE (tps65023_dcdc2_consumers), + .consumer_supplies = tps65023_dcdc2_consumers, + }, +/* dcdc3 */ + { + .constraints = { + .min_uV =1200000 , + .max_uV =1200000 , + .valid_ops_mask = (REGULATOR_CHANGE_STATUS ), + .boot_on =1 , + }, + .num_consumer_supplies =ARRAY_SIZE (tps65023_dcdc3_consumers), + .consumer_supplies = tps65023_dcdc3_consumers, + }, +/* ldo1 */ + { + .constraints = { + .min_uV =1800000 , + .max_uV =1800000 , + .valid_ops_mask = (REGULATOR_CHANGE_STATUS ), + .boot_on =1 , + }, + .num_consumer_supplies =ARRAY_SIZE (tps65023_ldo1_consumers), + .consumer_supplies = tps65023_ldo1_consumers, + }, +/* ldo2 */ + { + .constraints = { + .min_uV =2500000 , + .max_uV =3300000 , + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | +REGULATOR_CHANGE_STATUS ), + .boot_on =1 , + }, + .num_consumer_supplies =ARRAY_SIZE (tps65023_ldo2_consumers), + .consumer_supplies = tps65023_ldo2_consumers, + }, +}; + +static struct i2c_board_info __initdata mityomap_tps65023_info[] = { + { +I2C_BOARD_INFO ("tps65023" ,0x48 ), + .platform_data = &tps65023_regulator_data[0 ], + }, + { +I2C_BOARD_INFO ("24c02" ,0x50 ), + }, +}; + +static int __init pmic_tps65023_init (void ) +{ +return i2c_register_board_info (1 , mityomap_tps65023_info, +ARRAY_SIZE (mityomap_tps65023_info)); +} +/* * MityDSP-L138 includes a 256 MByte large-page NAND flash * (128K blocks).
@@ -172,6 +309,14 @@ static void __init mityomapl138_init(void)davinci_serial_init (&mityomapl138_uart_config); + ret =da8xx_register_i2c (0 , &mityomap_i2c_0_pdata); +if (ret) +pr_warning ("i2c0 registration failed %d\n" , ret); + + ret =pmic_tps65023_init (); +if (ret) +pr_warning ("TPS65023 PMIC init failed: %d\n" , ret); +mityomapl138_setup_nand ();mityomapl138_config_emac ();
Signature · 1 line
1.7.0.4
PATCH 1/1 davinci: Add I2C0 devices to MityDSP-L138/MityARM-1808 platform
Hello.
Quoted 6 lines · Michael Williamson
This patch adds the i2c0 bus and attached devices to the MityDSP-L138 and MityARM-1808 davinci SoM. Included is a TPS65023 voltage regulator needed for power management and a small 24c02 EPROM that contains factory configuration data.
Signed-off-by Michael Williamson<[email protected]>
[...]
Quoted 4 lines
arch/arm/mach-davinci/board-mityomapl138.c +0
-0
[...]
Quoted 1 line
arch/arm/mach-davinci/board-mityomapl138.c +0
-0@@ -25,6 +27,141 @@
[...]
arch/arm/mach-davinci/board-mityomapl138.c line 96
Quoted 8 lines
arch/arm/mach-davinci/board-mityomapl138.c +8
-0+struct regulator_init_data tps65023_regulator_data[] = { +/* dcdc1 */ + { + .constraints = { + .min_uV =1150000 , + .max_uV =1350000 , + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | +REGULATOR_CHANGE_STATUS ),
Would look better if you aligned it. And parens are useless here.
arch/arm/mach-davinci/board-mityomapl138.c line 107
Quoted 11 lines
arch/arm/mach-davinci/board-mityomapl138.c +11
-0+ .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc1_consumers), + .consumer_supplies = tps65023_dcdc1_consumers, + }, +/* dcdc2 */ + { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_ops_mask = (REGULATOR_CHANGE_STATUS),
Useless parens.
arch/arm/mach-davinci/board-mityomapl138.c line 118
Quoted 11 lines
arch/arm/mach-davinci/board-mityomapl138.c +11
-0+ .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc2_consumers), + .consumer_supplies = tps65023_dcdc2_consumers, + }, +/* dcdc3 */ + { + .constraints = { + .min_uV = 1200000, + .max_uV = 1200000, + .valid_ops_mask = (REGULATOR_CHANGE_STATUS),
Again...
arch/arm/mach-davinci/board-mityomapl138.c line 129
Quoted 11 lines
arch/arm/mach-davinci/board-mityomapl138.c +11
-0+ .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc3_consumers), + .consumer_supplies = tps65023_dcdc3_consumers, + }, +/* ldo1 */ + { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_ops_mask = (REGULATOR_CHANGE_STATUS),
And again...
arch/arm/mach-davinci/board-mityomapl138.c line 141
Quoted 12 lines
arch/arm/mach-davinci/board-mityomapl138.c +12
-0+ .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_ldo1_consumers), + .consumer_supplies = tps65023_ldo1_consumers, + }, +/* ldo2 */ + { + .constraints = { + .min_uV = 2500000, + .max_uV = 3300000, + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS),
Would look better if you aligned it. And parens are useless here.
arch/arm/mach-davinci/board-mityomapl138.c static void __init mityomapl138_init(void) · line 314
Quoted 7 lines
arch/arm/mach-davinci/board-mityomapl138.c +3
-0@@ -172,6 +309,14 @@ static void __init mityomapl138_init(void)davinci_serial_init (&mityomapl138_uart_config); + ret =da8xx_register_i2c (0 ,&mityomap_i2c_0_pdata); +if (ret) +pr_warning ("i2c0 registration failed %d\n" , ret);
You probably forgot semicolon after "failed" here...
arch/arm/mach-davinci/board-mityomapl138.c static void __init mityomapl138_init(void) · line 319
Quoted 5 lines
arch/arm/mach-davinci/board-mityomapl138.c +5
-0+ + ret =pmic_tps65023_init (); +if (ret) +pr_warning ("TPS65023 PMIC init failed: %d\n" , ret); +
WBR, Sergei
PATCH 1/1 davinci: Add I2C0 devices to MityDSP-L138/MityARM-1808 platform
Quoted 28 lines · Sergei Shtylyov
Hello.
Quoted 6 lines · Michael Williamson
This patch adds the i2c0 bus and attached devices to the MityDSP-L138 and MityARM-1808 davinci SoM. Included is a TPS65023 voltage regulator needed for power management and a small 24c02 EPROM that contains factory configuration data.
Signed-off-by Michael Williamson<[email protected]>[...]
Quoted 5 lines
arch/arm/mach-davinci/board-mityomapl138.c +0
-0[...]
Quoted 1 line
arch/arm/mach-davinci/board-mityomapl138.c +0
-0@@ -25,6 +27,141 @@[...]
arch/arm/mach-davinci/board-mityomapl138.c line 96
Quoted 8 lines
arch/arm/mach-davinci/board-mityomapl138.c +8
-0+struct regulator_init_data tps65023_regulator_data[] = { +/* dcdc1 */ + { + .constraints = { + .min_uV =1150000 , + .max_uV =1350000 , + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | +REGULATOR_CHANGE_STATUS ),
Quoted 2 lines
Would look better if you aligned it. And parens are useless here.
I'll clean it up, but I pretty much lifted it from board-da850-evm.c. The next time someone's in there, I suppose it should also be addressed.
Thanks for the comments.