s3c-fb: Add support ld9040 amoled panel driver
Subsystems (2)
PATCH 1/1 s3c-fb: Add support ld9040 amoled panel driver
This patch supports ld9040 amoled panel driver. It is similar to s6e63m0 panel driver and use spi gpio to send panel information.
--- drivers/video/backlight/Kconfig | 7 + drivers/video/backlight/Makefile | 1 + drivers/video/backlight/ld9040.c | 687 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 695 insertions(+), 0 deletions(-) create mode 100644 drivers/video/backlight/ld9040.c
drivers/video/backlight/Kconfig +7 -0
@@ -109,6 +109,13 @@ config LCD_S6E63M0 If you have an S6E63M0 LCD Panel, say Y to enable its LCD control driver. +config LCD_LD9040 + bool "LD9040 AMOLED LCD Driver" + depends on SPI && BACKLIGHT_CLASS_DEVICE + help + If you have an LD9040 LCD Panel, say Y to enable its + LCD control driver. + endif # LCD_CLASS_DEVICE #
drivers/video/backlight/Makefile +1 -0
@@ -12,6 +12,7 @@ obj-$(CONFIG_LCD_VGG2432A4) += vgg2432a4.o obj-$(CONFIG_LCD_TDO24M) += tdo24m.o obj-$(CONFIG_LCD_TOSA) += tosa_lcd.o obj-$(CONFIG_LCD_S6E63M0) += s6e63m0.o +obj-$(CONFIG_LCD_S6E63M0) += ld9040.o obj-$(CONFIG_BACKLIGHT_CLASS_DEVICE) += backlight.o obj-$(CONFIG_BACKLIGHT_ATMEL_PWM) += atmel-pwm-bl.o
drivers/video/backlight/ld9040.c new file +687 -0
687 lines not on this page · raw message
Signature · 1 line
1.6.0.4
PATCH 1/1 s3c-fb: Add support ld9040 amoled panel driver
Hello,
Quoted 3 lines · Donghwa Lee
This patch supports ld9040 amoled panel driver. It is similar to s6e63m0 panel driver and use spi gpio to send panel information.
You should remove the "s3c-fb" prefix from the patch subject, as the s3c-fb driver has nothing to LD9040 driver. Please use something generic like 'drivers: lcd:' or so.
Quoted 32 lines
Signed-off-by Donghwa Lee<[email protected]>Signed-off-by Inki Dae<[email protected]>--- drivers/video/backlight/Kconfig | 7 + drivers/video/backlight/Makefile | 1 + drivers/video/backlight/ld9040.c | 687 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 695 insertions(+), 0 deletions(-)create mode 100644
drivers/video/backlight/ld9040.cdrivers/video/backlight/Kconfig +7
-0@@ -109,6 +109,13 @@ config LCD_S6E63M0 If you have an S6E63M0 LCD Panel, say Y to enable its LCD control driver. +config LCD_LD9040 + bool "LD9040 AMOLED LCD Driver" + depends on SPI&& BACKLIGHT_CLASS_DEVICE + help + If you have an LD9040 LCD Panel, say Y to enable its + LCD control driver. + endif # LCD_CLASS_DEVICE #drivers/video/backlight/Makefile +0
-0
drivers/video/backlight/Makefile obj-$(CONFIG_LCD_VGG2432A4) += vgg2432a4.o · line 15
Quoted 4 lines
drivers/video/backlight/Makefile +1
-0@@ -12,6 +12,7 @@ obj-$(CONFIG_LCD_VGG2432A4) += vgg2432a4.o obj-$(CONFIG_LCD_TDO24M) += tdo24m.o obj-$(CONFIG_LCD_TOSA) += tosa_lcd.o obj-$(CONFIG_LCD_S6E63M0) += s6e63m0.o +obj-$(CONFIG_LCD_S6E63M0) += ld9040.o
You should use the newly defined LCD_LD9040 option in Makefile instead of hijacking the CONFIG_LCD_S6E63M0.
Quoted 559 lines
drivers/video/backlight/Makefile +0
-0obj-$(CONFIG_BACKLIGHT_CLASS_DEVICE) += backlight.o obj-$(CONFIG_BACKLIGHT_ATMEL_PWM) += atmel-pwm-bl.odrivers/video/backlight/ld9040.c new file +550
-0@@ -0,0 +1,687 @@ +/* +* ld9040 AMOLED LCD panel driver. +* +* Author: Donghwa Lee<[email protected]> +* +* Derived from drivers/video/omap/lcd-apollon.c +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +* This program is distributed in the hope that it will be useful, but +* WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* General Public License for more details. +* +* You should have received a copy of the GNU General Public License along +* with this program; if not, write to the Free Software Foundation, Inc., +* 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. +*/ + +#include <linux/wait.h> +#include <linux/fb.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/spi/spi.h> +#include <linux/irq.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/lcd.h> +#include <linux/backlight.h> + +#define SLEEPMSEC 0x1000 +#define ENDDEF 0x2000 +#define DEFMASK 0xFF00 +#define COMMAND_ONLY 0xFE +#define DATA_ONLY 0xFF + +#define POWER_IS_ON (pwr) ((pwr)<= FB_BLANK_NORMAL) + +struct ld9040 { +struct device *dev; +struct spi_device *spi; +unsigned int power; +struct lcd_device *ld; +struct lcd_platform_data *lcd_pd; +}; + +static const unsigned short SEQ_SWRESET [] = { +0x01 ,COMMAND_ONLY , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_USER_SETTING [] = { +0xF0 ,0x5A , + +DATA_ONLY ,0x5A , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_ELVSS [] = { +0xB1 ,0x0B , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x16 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_GTCON [] = { +0xF7 ,0x09 , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_GAMMA_SET1 [] = { +0xF9 ,0x18 , + +DATA_ONLY ,0x9A , +DATA_ONLY ,0xB0 , +DATA_ONLY ,0xAB , +DATA_ONLY ,0xC4 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0xAA , +DATA_ONLY ,0x00 , +DATA_ONLY ,0xA1 , +DATA_ONLY ,0xB5 , +DATA_ONLY ,0xB0 , +DATA_ONLY ,0xC7 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0xC5 , +DATA_ONLY ,0x24 , +DATA_ONLY ,0xA7 , +DATA_ONLY ,0xAC , +DATA_ONLY ,0x9A , +DATA_ONLY ,0xB6 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0xE5 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_GAMMA_CTRL [] = { +0xFB ,0x00 , + +DATA_ONLY ,0x5A , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_APON [] = { +0xF3 ,0x00 , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x0A , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_DISPCTL [] = { +0xF2 ,0x02 , + +DATA_ONLY ,0x03 , +DATA_ONLY ,0x1C , +DATA_ONLY ,0x10 , +DATA_ONLY ,0x10 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_SLPOUT [] = { +0x11 ,COMMAND_ONLY , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_SLPIN [] = { +0x10 ,COMMAND_ONLY , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_DISPON [] = { +0x29 ,COMMAND_ONLY , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_DISPOFF [] = { +0x28 ,COMMAND_ONLY , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VCI1_1ST_EN [] = { +0xF3 ,0x10 , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VL1_EN [] = { +0xF3 ,0x11 , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VL2_EN [] = { +0xF3 ,0x13 , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VCI1_2ND_EN [] = { +0xF3 ,0x33 , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VL3_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VREG1_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0x01 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VGH_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0x11 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VGL_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0x31 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x02 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VMOS_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xB1 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VINT_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xF1 , +/* DATA_ONLY, 0x71, VMOS/VBL/VBH not used */ +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +/* DATA_ONLY, 0x02, VMOS/VBL/VBH not used */ +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VBH_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xF9 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_VBL_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xFD , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_GAM_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xFF , +/* DATA_ONLY, 0x73, VMOS/VBL/VBH not used */ +DATA_ONLY ,0x00 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +/* DATA_ONLY, 0x02, VMOS/VBL/VBH not used */ +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_SD_AMP_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xFF , +/* DATA_ONLY, 0x73, VMOS/VBL/VBH not used */ +DATA_ONLY ,0x80 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +/* DATA_ONLY, 0x02, VMOS/VBL/VBH not used */ +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_GLS_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xFF , +/* DATA_ONLY, 0x73, VMOS/VBL/VBH not used */ +DATA_ONLY ,0x81 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +/* DATA_ONLY, 0x02, VMOS/VBL/VBH not used */ +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_ELS_EN [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xFF , +/* DATA_ONLY, 0x73, VMOS/VBL/VBH not used */ +DATA_ONLY ,0x83 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +/* DATA_ONLY, 0x02, VMOS/VBL/VBH not used */ +ENDDEF ,0x00 +}; + +static const unsigned short SEQ_EL_ON [] = { +0xF3 ,0x37 , + +DATA_ONLY ,0xFF , +/* DATA_ONLY, 0x73, VMOS/VBL/VBH not used */ +DATA_ONLY ,0x87 , +DATA_ONLY ,0x00 , +DATA_ONLY ,0x03 , +/* DATA_ONLY, 0x02, VMOS/VBL/VBH not used */ +ENDDEF ,0x00 +}; + +static int ld9040_spi_write_byte (struct ld9040 *lcd,int addr,int data) +{ +u16 buf[1 ]; +struct spi_message msg; + +struct spi_transfer xfer = { + .len =2 , + .tx_buf = buf, + }; + + buf[0 ] = (addr<<8 ) | data; + +spi_message_init (&msg); +spi_message_add_tail (&xfer,&msg); + +return spi_sync (lcd->spi,&msg); +} + +static int ld9040_spi_write (struct ld9040 *lcd,unsigned char address, +unsigned char command) +{ +int ret =0 ; + +if (address !=DATA_ONLY ) + ret =ld9040_spi_write_byte (lcd,0x0 , address); +if (command !=COMMAND_ONLY ) + ret =ld9040_spi_write_byte (lcd,0x1 , command); + +return ret; +} + +static int ld9040_panel_send_sequence (struct ld9040 *lcd, +const unsigned short *wbuf) +{ +int ret =0 , i =0 ; + +while ((wbuf[i]&DEFMASK ) !=ENDDEF ) { +if ((wbuf[i]&DEFMASK ) !=SLEEPMSEC ) { + ret =ld9040_spi_write (lcd, wbuf[i], wbuf[i+1 ]); +if (ret) +break ; + }else +udelay (wbuf[i+1 ]*1000 ); + i +=2 ; + } + +return ret; +} + +static int ld9040_ldi_init (struct ld9040 *lcd) +{ +int ret, i; +const unsigned short *init_seq[] = { +SEQ_USER_SETTING , +SEQ_ELVSS , +SEQ_GTCON , +SEQ_GAMMA_SET1 , +SEQ_GAMMA_CTRL , +SEQ_SLPOUT , + }; + +for (i =0 ; i<ARRAY_SIZE (init_seq); i++) { + ret =ld9040_panel_send_sequence (lcd, init_seq[i]); +mdelay (5 ); +if (ret) +break ; + } + +return ret; +} + +static int ld9040_ldi_enable (struct ld9040 *lcd) +{ +int ret =0 ; + + ret =ld9040_panel_send_sequence (lcd,SEQ_DISPON ); + +return ret; +} + +static int ld9040_ldi_disable (struct ld9040 *lcd) +{ +int ret; + + ret =ld9040_panel_send_sequence (lcd,SEQ_DISPOFF ); + +return ret; +} + +static int ld9040_power_on (struct ld9040 *lcd) +{ +int ret =0 ; +struct lcd_platform_data *pd =NULL ; + pd = lcd->lcd_pd; +if (!pd) { +dev_err (lcd->dev,"platform data is NULL.\n" ); +return -EFAULT ; + } + +if (!pd->power_on) { +dev_err (lcd->dev,"power_on is NULL.\n" ); +return -EFAULT ; + }else { + pd->power_on (lcd->ld,1 ); +mdelay (pd->power_on_delay); + } + +if (!pd->reset) { +dev_err (lcd->dev,"reset is NULL.\n" ); +return -EFAULT ; + }else { + pd->reset (lcd->ld); +mdelay (pd->reset_delay); + } + + ret =ld9040_ldi_init (lcd); +if (ret) { +dev_err (lcd->dev,"failed to initialize ldi.\n" ); +return ret; + } + + ret =ld9040_ldi_enable (lcd); +if (ret) { +dev_err (lcd->dev,"failed to enable ldi.\n" ); +return ret; + } + +return 0 ; +} + +static int ld9040_power_off (struct ld9040 *lcd) +{ +int ret =0 ; +struct lcd_platform_data *pd =NULL ; + + pd = lcd->lcd_pd; +if (!pd) { +dev_err (lcd->dev,"platform data is NULL.\n" ); +return -EFAULT ; + } + + ret =ld9040_ldi_disable (lcd); +if (ret) { +dev_err (lcd->dev,"lcd setting failed.\n" ); +return -EIO ; + } + +mdelay (pd->power_off_delay); + +if (!pd->power_on) { +dev_err (lcd->dev,"power_on is NULL.\n" ); +return -EFAULT ; + }else + pd->power_on (lcd->ld,0 ); + +return 0 ; +} + +static int ld9040_power (struct ld9040 *lcd,int power) +{ +int ret =0 ; + +if (POWER_IS_ON (power)&& !POWER_IS_ON (lcd->power)) + ret =ld9040_power_on (lcd); +else if (!POWER_IS_ON (power)&&POWER_IS_ON (lcd->power)) + ret =ld9040_power_off (lcd); + +if (!ret) + lcd->power = power; + +return ret; +} + +static int ld9040_set_power (struct lcd_device *ld,int power) +{ +struct ld9040 *lcd =lcd_get_data (ld); + +if (power !=FB_BLANK_UNBLANK && power !=FB_BLANK_POWERDOWN && + power !=FB_BLANK_NORMAL ) { +dev_err (lcd->dev,"power value should be 0, 1 or 4.\n" ); +return -EINVAL ; + } + +return ld9040_power (lcd, power); +} + +static int ld9040_get_power (struct lcd_device *ld) +{ +struct ld9040 *lcd =lcd_get_data (ld); + +return lcd->power; +} + +static struct lcd_ops ld9040_lcd_ops = { + .set_power = ld9040_set_power, + .get_power = ld9040_get_power, +}; + + +static int __init ld9040_probe (struct spi_device *spi) +{ +int ret =0 ; +struct ld9040 *lcd =NULL ; +struct lcd_device *ld =NULL ; + + lcd =kzalloc (sizeof (struct ld9040 ),GFP_KERNEL ); +if (!lcd) +return -ENOMEM ; + +/* ld9040 lcd panel uses 3-wire 9bits SPI Mode. */ + spi->bits_per_word =9 ; + + ret =spi_setup (spi); +if (ret<0 ) { +dev_err (&spi->dev,"spi setup failed.\n" ); + goto out_free_lcd; + } +
drivers/video/backlight/ld9040.c line 560
Quoted 10 lines
drivers/video/backlight/ld9040.c new file +10
-0+ lcd->spi = spi; + lcd->dev =&spi->dev; + + lcd->lcd_pd = (struct lcd_platform_data *)spi->dev.platform_data; +if (!lcd->lcd_pd) { +dev_err (&spi->dev,"platform data is NULL.\n" ); + goto out_free_lcd; + } + + ld =lcd_device_register ("ld9040" ,&spi->dev, lcd,&ld9040_lcd_ops);
Please be a bit more consistent in the coding style. There should be a space after a comma. This applies to the above line and the few other.
Quoted 117 lines
drivers/video/backlight/ld9040.c new file +117
-0+if (IS_ERR (ld)) { + ret =PTR_ERR (ld); + goto out_free_lcd; + } + + lcd->ld = ld; + +/* +* if lcd panel was on from bootloader like u-boot then +* do not lcd on. +*/ +if (!lcd->lcd_pd->lcd_enabled) { +/* +* if lcd panel was off from bootloader then +* current lcd status is powerdown and then +* it enables lcd panel. +*/ + lcd->power =FB_BLANK_POWERDOWN ; + +ld9040_power (lcd,FB_BLANK_UNBLANK ); + }else + lcd->power =FB_BLANK_UNBLANK ; + +dev_set_drvdata (&spi->dev, lcd); + +dev_info (&spi->dev,"ld9040 panel driver has been probed.\n" ); +return 0 ; + +out_free_lcd: +kfree (lcd); +return ret; +} + +static int __devexit ld9040_remove(struct spi_device *spi) +{ +struct ld9040 *lcd =dev_get_drvdata (&spi->dev); + +ld9040_power (lcd,FB_BLANK_POWERDOWN ); +lcd_device_unregister (lcd->ld); +kfree (lcd); + +return 0 ; +} + +#if defined(CONFIG_PM ) +unsigned int beforepower; + +static int ld9040_suspend (struct spi_device *spi,pm_message_t mesg) +{ +int ret =0 ; +struct ld9040 *lcd =dev_get_drvdata (&spi->dev); + +dev_dbg (&spi->dev,"lcd->power = %d\n" , lcd->power); + + beforepower = lcd->power; + +/* +* when lcd panel is suspend, lcd panel becomes off +* regardless of status. +*/ + ret =ld9040_power (lcd,FB_BLANK_POWERDOWN ); + +return ret; +} + +static int ld9040_resume (struct spi_device *spi) +{ +int ret =0 ; +struct ld9040 *lcd =dev_get_drvdata (&spi->dev); + +/* +* after suspended, if lcd panel status is FB_BLANK_UNBLANK +* (at that time, power is FB_BLANK_UNBLANK) then +* it changes that status to FB_BLANK_POWERDOWN to get lcd on. +*/ +if (beforepower ==FB_BLANK_UNBLANK ) + lcd->power =FB_BLANK_POWERDOWN ; + +dev_dbg (&spi->dev,"power = %d\n" , beforepower); + + ret =ld9040_power (lcd, beforepower); + +return ret; +} +#else +#define ld9040_suspend NULL +#define ld9040_resume NULL +#endif + +/* Power down all displays on reboot, poweroff or halt. */ +static void ld9040_shutdown (struct spi_device *spi) +{ +struct ld9040 *lcd =dev_get_drvdata (&spi->dev); + +ld9040_power (lcd,FB_BLANK_POWERDOWN ); +} + +static struct spi_driver ld9040_driver = { + .driver = { + .name ="ld9040" , + .bus =&spi_bus_type, + .owner =THIS_MODULE , + }, + .probe = ld9040_probe, + .remove =__devexit_p (ld9040_remove), + .shutdown = ld9040_shutdown, + .suspend = ld9040_suspend, + .resume = ld9040_resume, +}; + +static int __init ld9040_init (void ) +{ +return spi_register_driver (&ld9040_driver); +} + +static void __exit ld9040_exit(void) +{
drivers/video/backlight/ld9040.c line 687
Quoted 10 lines
drivers/video/backlight/ld9040.c new file +10
-0+spi_unregister_driver (&ld9040_driver); +} + +module_init (ld9040_init); +module_exit (ld9040_exit); + +MODULE_AUTHOR ("Donghwa Lee<[email protected]>" ); +MODULE_DESCRIPTION ("ld9040 LCD Driver" ); +MODULE_LICENSE ("GPL" ); +
Best regards
Signature · 2 lines
Marek Szyprowski Samsung Poland R&D Center