Skip to contentSkip to conversation

iio: Change GAIN macros to SCALE.

PATCH In review [email protected] 3 participants 4 messages Sep 9, 2010 – Sep 10, 2010

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 iio: Change GAIN macros to SCALE.

From: Andrew Chew <[email protected]>

Per email exchange with Jonathan Cameron, GAIN should instead be SCALE, to be consistent with documentation.

Resending, since this goes with the 2/2 patch.

---
 drivers/staging/iio/magnetometer/magnet.h |   12 ++++++------
 1 files changed, 6 insertions(+), 6 deletions(-)
drivers/staging/iio/magnetometer/magnet.h +6 -6
index 6433830..1260eb7 100644
@@ -12,14 +12,14 @@
 #define IIO_DEV_ATTR_MAGN_Z_OFFSET(_mode, _show, _store, _addr)	\
 	IIO_DEVICE_ATTR(magn_z_offset, _mode, _show, _store, _addr)
 
-#define IIO_DEV_ATTR_MAGN_X_GAIN(_mode, _show, _store, _addr)		\
-	IIO_DEVICE_ATTR(magn_x_gain, _mode, _show, _store, _addr)
+#define IIO_DEV_ATTR_MAGN_X_SCALE(_mode, _show, _store, _addr)		\
+	IIO_DEVICE_ATTR(magn_x_scale, _mode, _show, _store, _addr)
 
-#define IIO_DEV_ATTR_MAGN_Y_GAIN(_mode, _show, _store, _addr)		\
-	IIO_DEVICE_ATTR(magn_y_gain, _mode, _show, _store, _addr)
+#define IIO_DEV_ATTR_MAGN_Y_SCALE(_mode, _show, _store, _addr)		\
+	IIO_DEVICE_ATTR(magn_y_scale, _mode, _show, _store, _addr)
 
-#define IIO_DEV_ATTR_MAGN_Z_GAIN(_mode, _show, _store, _addr)		\
-	IIO_DEVICE_ATTR(magn_z_gain, _mode, _show, _store, _addr)
+#define IIO_DEV_ATTR_MAGN_Z_SCALE(_mode, _show, _store, _addr)		\
+	IIO_DEVICE_ATTR(magn_z_scale, _mode, _show, _store, _addr)
 
 #define IIO_DEV_ATTR_MAGN_X(_show, _addr)				\
 	IIO_DEVICE_ATTR(magn_x_raw, S_IRUGO, _show, NULL, _addr)
Signature · 9 lines
1.7.0.4


-----------------------------------------------------------------------------------
This email message is for the sole use of the intended recipient(s) and may contain
confidential information.  Any unauthorized review, use, disclosure or distribution
is prohibited.  If you are not the intended recipient, please contact the sender by
reply email and destroy all copies of the original message.
-----------------------------------------------------------------------------------
#1 lore raw

PATCH v3 2/2 iio: ak8975: Add ak8975 magnetometer sensor

From: Andrew Chew <[email protected]>

This is for the Asahi Kasei AK8975 3-axis magnetometer. It resides within the magnetometer section of the IIO subsystem, and implements the raw magn_x,y,z_raw attributes, as well as magn_x,y,z_scale attributes for converting to Gauss.

Changed to use the magn_x,y,z_scale attributes, and made those attributes give the scale factor to conert to Gauss. Also applied more fixes from feedback.

Keeping mode as an unsigned long. I'm going to add proper power management at some point anyway, which would deprecate this attribute.

---
 drivers/staging/iio/magnetometer/Kconfig  |   10 +
 drivers/staging/iio/magnetometer/Makefile |    1 +
 drivers/staging/iio/magnetometer/ak8975.c |  558 +++++++++++++++++++++++++++++
 3 files changed, 569 insertions(+), 0 deletions(-)
 create mode 100644 drivers/staging/iio/magnetometer/ak8975.c
drivers/staging/iio/magnetometer/Kconfig +10 -0
index d014450..81b579d 100644
@@ -3,6 +3,16 @@
 #
 comment "Magnetometer sensors"
 
+config SENSORS_AK8975
+	tristate "Asahi Kasei AK8975 3-Axis Magnetometer"
+	depends on I2C
+	help
+	  Say yes here to build support for Asahi Kasei AK8975 3-Axis
+	  Magnetometer.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ak8975.
+
 config SENSORS_HMC5843
 	tristate "Honeywell HMC5843 3-Axis Magnetometer"
 	depends on I2C
drivers/staging/iio/magnetometer/Makefile +1 -0
index f9bfb2e..f2a753f 100644
@@ -2,4 +2,5 @@
 # Makefile for industrial I/O Magnetometer sensors
 #
 
+obj-$(CONFIG_SENSORS_AK8975)	+= ak8975.o
 obj-$(CONFIG_SENSORS_HMC5843)	+= hmc5843.o
drivers/staging/iio/magnetometer/ak8975.c new file +558 -0

558 lines not on this page · raw message

Signature · 9 lines
1.7.0.4


-----------------------------------------------------------------------------------
This email message is for the sole use of the intended recipient(s) and may contain
confidential information.  Any unauthorized review, use, disclosure or distribution
is prohibited.  If you are not the intended recipient, please contact the sender by
reply email and destroy all copies of the original message.
-----------------------------------------------------------------------------------
Acked-by on v3 2/2
#2 lore raw

Re: [PATCH 2/2 V3] iio: ak8975: Add ak8975 magnetometer sensor

Quoted 1 line · On 09/09/10 06:02, [email protected] wrote:

From: Andrew Chew <[email protected]>

Hi Andrew,

Quoted 11 lines

This is for the Asahi Kasei AK8975 3-axis magnetometer. It resides within the magnetometer section of the IIO subsystem, and implements the raw magn_x,y,z_raw attributes, as well as magn_x,y,z_scale attributes for converting to Gauss.

Changed to use the magn_x,y,z_scale attributes, and made those attributes give the scale factor to conert to Gauss. Also applied more fixes from feedback.

Keeping mode as an unsigned long. I'm going to add proper power management at some point anyway, which would deprecate this attribute.

Fair enough. Alan, you raised the issue of runtime power management. Are you happy to let the patch merge on the basis that Andrew will look at it in the future? (it is in staging afterall so a bit more leeway than elsewhere is probably reasonable!)

A couple of comments inline. Most of them are observations rather than things I'm necessarily suggesting you need to actually change.

The only exceptions are the unused eoc_irq element and all references to it + w_data being too large. Please fix those two and I'm happy to add:

If you prefer, then feel free to do the cleanups as a follow up patch. They don't cause any harm after all.

As an aside,
it is usually best to CC anyone who has contributed to reviews of previous versions to verify they are now happy. To that end I have cc'd Alan and Samu. (Andrew M's comments were submission style related)

For some strange reason not everyone is on linux-iio ;) (yet)

Quoted 154 lines
---
 drivers/staging/iio/magnetometer/Kconfig  |   10 +
 drivers/staging/iio/magnetometer/Makefile |    1 +
 drivers/staging/iio/magnetometer/ak8975.c |  558 +++++++++++++++++++++++++++++
 3 files changed, 569 insertions(+), 0 deletions(-)
 create mode 100644 drivers/staging/iio/magnetometer/ak8975.c
drivers/staging/iio/magnetometer/Kconfig +10 -0
index d014450..81b579d 100644
@@ -3,6 +3,16 @@
 #
 comment "Magnetometer sensors"
 
+config SENSORS_AK8975
+	tristate "Asahi Kasei AK8975 3-Axis Magnetometer"
+	depends on I2C
+	help
+	  Say yes here to build support for Asahi Kasei AK8975 3-Axis
+	  Magnetometer.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ak8975.
+
 config SENSORS_HMC5843
 	tristate "Honeywell HMC5843 3-Axis Magnetometer"
 	depends on I2C
drivers/staging/iio/magnetometer/Makefile +1 -0
index f9bfb2e..f2a753f 100644
@@ -2,4 +2,5 @@
 # Makefile for industrial I/O Magnetometer sensors
 #
 
+obj-$(CONFIG_SENSORS_AK8975)	+= ak8975.o
 obj-$(CONFIG_SENSORS_HMC5843)	+= hmc5843.o
drivers/staging/iio/magnetometer/ak8975.c new file +108 -0
new file mode 100644
index 0000000..420f206
@@ -0,0 +1,558 @@
+/*
+ * A sensor driver for the magnetometer AK8975.
+ *
+ * Magnetic compass sensor driver for monitoring magnetic flux information.
+ *
+ * Copyright (c) 2010, NVIDIA Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA	02110-1301, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+
+#include <linux/gpio.h>
+
+#include "../iio.h"
+#include "magnet.h"
+
+/*
+ * Register definitions, as well as various shifts and masks to get at the
+ * individual fields of the registers.
+ */
+#define AK8975_REG_WIA			0x00
+#define AK8975_DEVICE_ID		0x48
+
+#define AK8975_REG_INFO			0x01
+
+#define AK8975_REG_ST1			0x02
+#define AK8975_REG_ST1_DRDY_SHIFT	0
+#define AK8975_REG_ST1_DRDY_MASK	(1 << AK8975_REG_ST1_DRDY_SHIFT)
+
+#define AK8975_REG_HXL			0x03
+#define AK8975_REG_HXH			0x04
+#define AK8975_REG_HYL			0x05
+#define AK8975_REG_HYH			0x06
+#define AK8975_REG_HZL			0x07
+#define AK8975_REG_HZH			0x08
+#define AK8975_REG_ST2			0x09
+#define AK8975_REG_ST2_DERR_SHIFT	2
+#define AK8975_REG_ST2_DERR_MASK	(1 << AK8975_REG_ST2_DERR_SHIFT)
+
+#define AK8975_REG_ST2_HOFL_SHIFT	3
+#define AK8975_REG_ST2_HOFL_MASK	(1 << AK8975_REG_ST2_HOFL_SHIFT)
+
+#define AK8975_REG_CNTL			0x0A
+#define AK8975_REG_CNTL_MODE_SHIFT	0
+#define AK8975_REG_CNTL_MODE_MASK	(0xF << AK8975_REG_CNTL_MODE_SHIFT)
+#define AK8975_REG_CNTL_MODE_POWER_DOWN	0
+#define AK8975_REG_CNTL_MODE_ONCE	1
+#define AK8975_REG_CNTL_MODE_SELF_TEST	8
+#define AK8975_REG_CNTL_MODE_FUSE_ROM	0xF
+
+#define AK8975_REG_RSVC			0x0B
+#define AK8975_REG_ASTC			0x0C
+#define AK8975_REG_TS1			0x0D
+#define AK8975_REG_TS2			0x0E
+#define AK8975_REG_I2CDIS		0x0F
+#define AK8975_REG_ASAX			0x10
+#define AK8975_REG_ASAY			0x11
+#define AK8975_REG_ASAZ			0x12
+
+#define AK8975_MAX_REGS			AK8975_REG_ASAZ
+
+/*
+ * Miscellaneous values.
+ */
+#define AK8975_MAX_CONVERSION_TIMEOUT	500
+#define AK8975_CONVERSION_DONE_POLL_TIME 10
+
+/*
+ * Per-instance context data for the device.
+ */
+struct ak8975_data {
+	struct i2c_client	*client;
+	struct iio_dev		*indio_dev;
+	struct attribute_group	attrs;
+	struct mutex		lock;
+	u8			asa[3];
+	long			raw_to_gauss[3];
+	unsigned long		mode;
+	u8			reg_cache[AK8975_MAX_REGS];
+	int			eoc_gpio;
+	int			eoc_irq;
+};
+
+/*
+ * Helper function to write to the I2C device's registers.
+ */
+static int ak8975_write_data(struct i2c_client *client,
+			     u8 reg, u8 val, u8 mask, u8 shift)
+{

drivers/staging/iio/magnetometer/ak8975.c line 118

Quoted 10 lines
drivers/staging/iio/magnetometer/ak8975.c new file +10 -0
+	u8 regval;
+	struct i2c_msg msg;
+	u8 w_data[2];
+	int ret = 0;
+
+	struct ak8975_data *data = i2c_get_clientdata(client);
+
+	regval = data->reg_cache[reg];
+	regval &= ~mask;
+	regval |= val << shift;

An aside: Does this combination correspond to any of the convenient i2c functions? I thing it would be:
i2c_smbus_write_byte_data(client, reg, regval);

Quoted 15 lines
drivers/staging/iio/magnetometer/ak8975.c new file +15 -0
+
+	w_data[0] = reg;
+	w_data[1] = regval;
+
+	msg.addr = client->addr;
+	msg.flags = 0;
+	msg.len = 2;
+	msg.buf = w_data;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0) {
+		dev_err(&client->dev, "Write to device fails status %x\n", ret);
+		return ret;
+	}
+	data->reg_cache[reg] = regval;

drivers/staging/iio/magnetometer/ak8975.c line 143

Quoted 10 lines
drivers/staging/iio/magnetometer/ak8975.c new file +10 -0
+
+	return 0;
+}
+
+/*
+ * Helper function to read a contiguous set of the I2C device's registers.
+ */
+static int ak8975_read_data(struct i2c_client *client,
+			    u8 reg, u8 length, u8 *buffer)
+{

Could use c99 style assignments to fill this here. So (having moved relevant other defs above it),

struct i2c_msg msg[2] = {
       {
		.addr = client->addr,
       		.flags = I2C_M_NOSTART,
       		.len = 1,
		//or just use &reg here.
       		.buf = w_data,
       }, {
		.addr = client->addr,
		.flags = I2c_M_RD,
		.len = length,
		.buf = buffer,
       }
};

drivers/staging/iio/magnetometer/ak8975.c line 144

Quoted 1 line
drivers/staging/iio/magnetometer/ak8975.c new file +1 -0
+	struct i2c_msg msg[2];

Why does this have 2 elements? (or as above question exist at all).

drivers/staging/iio/magnetometer/ak8975.c line 150

Quoted 6 lines
drivers/staging/iio/magnetometer/ak8975.c new file +6 -0
+	u8 w_data[2];
+	int ret;
+
+	w_data[0] = reg;
+
+	msg[0].addr = client->addr;

That is a bit nasty as it will need IEC_FUNC_PROTOCOL_MANGLING to be available. If that wasn't there, I'm not entirely certain, but it looks like i2c_smbus_read_block_data would cover this function nicely?

drivers/staging/iio/magnetometer/ak8975.c line 159

Quoted 9 lines
drivers/staging/iio/magnetometer/ak8975.c new file +9 -0
+	msg[0].flags = I2C_M_NOSTART;	/* set repeated start and write */
+	msg[0].len = 1;
+	msg[0].buf = w_data;
+
+	msg[1].addr = client->addr;
+	msg[1].flags = I2C_M_RD;
+	msg[1].len = length;
+	msg[1].buf = buffer;
+

using ARRAY_SIZE(msg) for the 2 would make the code marginally clearer.

Quoted 169 lines
drivers/staging/iio/magnetometer/ak8975.c new file +169 -0
+	ret = i2c_transfer(client->adapter, msg, 2);
+	if (ret < 0) {
+		dev_err(&client->dev, "Read from device fails\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Perform some start-of-day setup, including reading the asa calibration
+ * values and caching them.
+ */
+static int ak8975_setup(struct i2c_client *client)
+{
+	struct ak8975_data *data = i2c_get_clientdata(client);
+	u8 device_id;
+	int ret;
+
+	/* Confirm that the device we're talking to is really an AK8975. */
+	ret = ak8975_read_data(client, AK8975_REG_WIA, 1, &device_id);
+	if (ret < 0) {
+		dev_err(&client->dev, "Error reading WIA\n");
+		return ret;
+	}
+	if (device_id != AK8975_DEVICE_ID) {
+		dev_err(&client->dev, "Device ak8975 not found\n");
+		return -ENODEV;
+	}
+
+	/* Write the fused rom access mode. */
+	ret = ak8975_write_data(client,
+				AK8975_REG_CNTL,
+				AK8975_REG_CNTL_MODE_FUSE_ROM,
+				AK8975_REG_CNTL_MODE_MASK,
+				AK8975_REG_CNTL_MODE_SHIFT);
+	if (ret < 0) {
+		dev_err(&client->dev, "Error in setting fuse access mode\n");
+		return ret;
+	}
+
+	/* Get asa data and store in the device data. */
+	ret = ak8975_read_data(client, AK8975_REG_ASAX, 3, data->asa);
+	if (ret < 0) {
+		dev_err(&client->dev, "Not able to read asa data\n");
+		return ret;
+	}
+
+	/* Precalculate scale factor for each axis and
+           store in the device data. */
+	data->raw_to_gauss[0] = ((data->asa[0] + 128) * 30) >> 8;
+	data->raw_to_gauss[1] = ((data->asa[1] + 128) * 30) >> 8;
+	data->raw_to_gauss[2] = ((data->asa[2] + 128) * 30) >> 8;
+
+	return 0;
+}
+
+/*
+ * Shows the device's mode.  0 = off, 1 = on.
+ */
+static ssize_t show_mode(struct device *dev, struct device_attribute *devattr,
+			 char *buf)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ak8975_data *data = indio_dev->dev_data;
+
+	return sprintf(buf, "%lu\n", data->mode);
+}
+
+/*
+ * Sets the device's mode.  0 = off, 1 = on.  The device's mode must be on
+ * for the magn raw attributes to be available.
+ */
+static ssize_t store_mode(struct device *dev, struct device_attribute *devattr,
+			  const char *buf, size_t count)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ak8975_data *data = indio_dev->dev_data;
+	struct i2c_client *client = data->client;
+	unsigned long oval;
+	int ret;
+
+	/* Convert mode string and do some basic sanity checking on it.
+	   only 0 or 1 are valid. */
+	if (strict_strtoul(buf, 10, &oval))
+		return -EINVAL;
+
+	if (oval > 1) {
+		dev_err(dev, "mode value is not supported\n");
+		return -EINVAL;
+	}
+
+	mutex_lock(&data->lock);
+
+	/* Write the mode to the device. */
+	if (data->mode != oval) {
+		ret = ak8975_write_data(client,
+					AK8975_REG_CNTL,
+					(u8)oval,
+					AK8975_REG_CNTL_MODE_MASK,
+					AK8975_REG_CNTL_MODE_SHIFT);
+
+		if (ret < 0) {
+			dev_err(&client->dev, "Error in setting mode\n");
+			mutex_unlock(&data->lock);
+			return ret;
+		}
+		data->mode = oval;
+	}
+
+	mutex_unlock(&data->lock);
+
+	return count;
+}
+
+/*
+ * Emits the scale factor to bring the raw value into Gauss units.
+ *
+ * This scale factor is axis-dependent, and is derived from 3 calibration
+ * factors ASA(x), ASA(y), and ASA(z).
+ *
+ * These ASA values are read from the sensor device at start of day, and
+ * cached in the device context struct.
+ *
+ * Adjusting the flux value with the sensitivity adjustment value should be
+ * done via the following formula:
+ *
+ * Hadj = H * ( ( ( (ASA-128)*0.5 ) / 128 ) + 1 )
+ *
+ * where H is the raw value, ASA is the sensitivity adjustment, and Hadj
+ * is the resultant adjusted value.
+ *
+ * We reduce the formula to:
+ *
+ * Hadj = H * (ASA + 128) / 256
+ *
+ * H is in the range of -4096 to 4095.  The magnetometer has a range of
+ * +-1229uT.  To go from the raw value to uT is:
+ *
+ * HuT = H * 1229/4096, or roughly, 3/10.
+ *
+ * Since 1uT = 100 gauss, our final scale factor becomes:
+ *
+ * Hadj = H * ((ASA + 128) / 256) * 3/10 * 100
+ * Hadj = H * ((ASA + 128) * 30 / 256
+ *
+ * Since ASA doesn't change, we cache the resultant scale factor into the
+ * device context in ak8975_setup().
+ */
+static ssize_t show_scale(struct device *dev, struct device_attribute *devattr,
+			  char *buf)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ak8975_data *data = indio_dev->dev_data;
+	struct iio_dev_attr *this_attr = to_iio_dev_attr(devattr);
+
+	return sprintf(buf, "%ld\n", data->raw_to_gauss[this_attr->address]);
+}
+
+/*
+ * Emits the raw flux value for the x, y, or z axis.
+ */
+static ssize_t show_raw(struct device *dev, struct device_attribute *devattr,
+			char *buf)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ak8975_data *data = indio_dev->dev_data;
+	struct i2c_client *client = data->client;
+	struct iio_dev_attr *this_attr = to_iio_dev_attr(devattr);

drivers/staging/iio/magnetometer/ak8975.c line 338

Quoted 10 lines
drivers/staging/iio/magnetometer/ak8975.c new file +10 -0
+	u32 timeout_ms = AK8975_MAX_CONVERSION_TIMEOUT;
+	u16 meas_reg;
+	s16 raw;
+	u8 read_status;
+	int ret;
+
+	mutex_lock(&data->lock);
+
+	if (data->mode == 0) {
+		dev_err(&client->dev, "Operating mode is in power down mode\n");

That's not really an error. I'd just not bother printing anything if this happens.

Quoted 53 lines
drivers/staging/iio/magnetometer/ak8975.c new file +53 -0
+		ret = -EBUSY;
+		goto exit;
+	}
+
+	/* Set up the device for taking a sample. */
+	ret = ak8975_write_data(client,
+				AK8975_REG_CNTL,
+				AK8975_REG_CNTL_MODE_ONCE,
+				AK8975_REG_CNTL_MODE_MASK,
+				AK8975_REG_CNTL_MODE_SHIFT);
+	if (ret < 0) {
+		dev_err(&client->dev, "Error in setting operating mode\n");
+		goto exit;
+	}
+
+	/* Wait for the conversion to complete. */
+	while (timeout_ms) {
+		msleep(AK8975_CONVERSION_DONE_POLL_TIME);
+		if (gpio_get_value(data->eoc_gpio))
+			break;
+		timeout_ms -= AK8975_CONVERSION_DONE_POLL_TIME;
+	}
+	if (!timeout_ms) {
+		dev_err(&client->dev, "Conversion timeout happened\n");
+		ret = -EINVAL;
+		goto exit;
+	}
+
+	ret = ak8975_read_data(client, AK8975_REG_ST1, 1, &read_status);
+	if (ret < 0) {
+		dev_err(&client->dev, "Error in reading ST1\n");
+		goto exit;
+	}
+
+	if (read_status & AK8975_REG_ST1_DRDY_MASK) {
+		ret = ak8975_read_data(client, AK8975_REG_ST2, 1, &read_status);
+		if (ret < 0) {
+			dev_err(&client->dev, "Error in reading ST2\n");
+			goto exit;
+		}
+		if (read_status & (AK8975_REG_ST2_DERR_MASK |
+				   AK8975_REG_ST2_HOFL_MASK)) {
+			dev_err(&client->dev, "ST2 status error 0x%x\n",
+				read_status);
+			ret = -EINVAL;
+			goto exit;
+		}
+	}
+
+	/* Read the flux value from the appropriate register
+	   (the register is specified in the iio device attributes). */
+	ret = ak8975_read_data(client, this_attr->address, 2, (u8 *)&meas_reg);
+	if (ret < 0) {

drivers/staging/iio/magnetometer/ak8975.c line 401

Quoted 10 lines
drivers/staging/iio/magnetometer/ak8975.c new file +10 -0
+		dev_err(&client->dev, "Read axis data fails\n");
+		goto exit;
+	}
+
+	mutex_unlock(&data->lock);
+
+	/* Endian conversion of the measured values. */
+	raw = (s16) (le16_to_cpu(meas_reg));
+
+	/* Clamp to valid range. */

Is there any way it can be outside this?

Quoted 42 lines
drivers/staging/iio/magnetometer/ak8975.c new file +42 -0
+	raw = clamp_t(s16, raw, -4096, 4095);
+
+	return sprintf(buf, "%d\n", raw);
+
+exit:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static IIO_DEVICE_ATTR(mode, S_IRUGO | S_IWUSR, show_mode, store_mode, 0);
+static IIO_DEV_ATTR_MAGN_X_SCALE(S_IRUGO, show_scale, NULL, 0);
+static IIO_DEV_ATTR_MAGN_Y_SCALE(S_IRUGO, show_scale, NULL, 1);
+static IIO_DEV_ATTR_MAGN_Z_SCALE(S_IRUGO, show_scale, NULL, 2);
+static IIO_DEV_ATTR_MAGN_X(show_raw, AK8975_REG_HXL);
+static IIO_DEV_ATTR_MAGN_Y(show_raw, AK8975_REG_HYL);
+static IIO_DEV_ATTR_MAGN_Z(show_raw, AK8975_REG_HZL);
+
+static struct attribute *ak8975_attr[] = {
+	&iio_dev_attr_mode.dev_attr.attr,
+	&iio_dev_attr_magn_x_scale.dev_attr.attr,
+	&iio_dev_attr_magn_y_scale.dev_attr.attr,
+	&iio_dev_attr_magn_z_scale.dev_attr.attr,
+	&iio_dev_attr_magn_x_raw.dev_attr.attr,
+	&iio_dev_attr_magn_y_raw.dev_attr.attr,
+	&iio_dev_attr_magn_z_raw.dev_attr.attr,
+	NULL
+};
+
+static struct attribute_group ak8975_attr_group = {
+	.attrs = ak8975_attr,
+};
+
+static int ak8975_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct ak8975_data *data;
+	int err;
+
+	/* Allocate our device context. */
+	data = kzalloc(sizeof(struct ak8975_data), GFP_KERNEL);
+	if (!data) {
+		dev_err(&client->dev, "Memory allocation fails\n");

drivers/staging/iio/magnetometer/ak8975.c line 453

Quoted 10 lines
drivers/staging/iio/magnetometer/ak8975.c new file +10 -0
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	i2c_set_clientdata(client, data);
+	data->client = client;
+
+	mutex_init(&data->lock);
+
+	/* Grab and set up the supplied GPIO. */

Client irq should always be available (I think) so what gain in making a copy, even more so given you never use it! In fact you don't use any interrupts at all at the moment.

Quoted 105 lines
drivers/staging/iio/magnetometer/ak8975.c new file +105 -0
+	data->eoc_irq = client->irq;
+	data->eoc_gpio = irq_to_gpio(client->irq);
+
+	if (!data->eoc_gpio) {
+		dev_err(&client->dev, "failed, no valid GPIO\n");
+		err = -EINVAL;
+		goto exit_free;
+	}
+
+	err = gpio_request(data->eoc_gpio, "ak_8975");
+	if (err < 0) {
+		dev_err(&client->dev, "failed to request GPIO %d, error %d\n",
+			data->eoc_gpio, err);
+		goto exit_free;
+	}
+
+	err = gpio_direction_input(data->eoc_gpio);
+	if (err < 0) {
+		dev_err(&client->dev, "Failed to configure input direction for"
+			" GPIO %d, error %d\n", data->eoc_gpio, err);
+		goto exit_gpio;
+	}
+
+	/* Perform some basic start-of-day setup of the device. */
+	err = ak8975_setup(client);
+	if (err < 0) {
+		dev_err(&client->dev, "AK8975 initialization fails\n");
+		goto exit_gpio;
+	}
+
+	/* Register with IIO */
+	data->indio_dev = iio_allocate_device();
+	if (data->indio_dev == NULL) {
+		err = -ENOMEM;
+		goto exit_gpio;
+	}
+
+	data->indio_dev->dev.parent = &client->dev;
+	data->indio_dev->attrs = &ak8975_attr_group;
+	data->indio_dev->dev_data = (void *)(data);
+	data->indio_dev->driver_module = THIS_MODULE;
+	data->indio_dev->modes = INDIO_DIRECT_MODE;
+
+	err = iio_device_register(data->indio_dev);
+	if (err < 0)
+		goto exit_free_iio;
+
+	return 0;
+
+exit_free_iio:
+	iio_free_device(data->indio_dev);
+exit_gpio:
+	gpio_free(data->eoc_gpio);
+exit_free:
+	kfree(data);
+exit:
+	return err;
+}
+
+static int ak8975_remove(struct i2c_client *client)
+{
+	struct ak8975_data *data = i2c_get_clientdata(client);
+
+	iio_device_unregister(data->indio_dev);
+	iio_free_device(data->indio_dev);
+
+	gpio_free(data->eoc_gpio);
+
+	kfree(data);
+
+	return 0;
+}
+
+static const struct i2c_device_id ak8975_id[] = {
+	{"ak8975", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, ak8975_id);
+
+static struct i2c_driver ak8975_driver = {
+	.driver = {
+		.name	= "ak8975",
+	},
+	.probe		= ak8975_probe,
+	.remove		= __devexit_p(ak8975_remove),
+	.id_table	= ak8975_id,
+};
+
+static int __init ak8975_init(void)
+{
+	return i2c_add_driver(&ak8975_driver);
+}
+
+static void __exit ak8975_exit(void)
+{
+	i2c_del_driver(&ak8975_driver);
+}
+
+module_init(ak8975_init);
+module_exit(ak8975_exit);
+
+MODULE_AUTHOR("Laxman Dewangan <[email protected]>");
+MODULE_DESCRIPTION("AK8975 magnetometer driver");
+MODULE_LICENSE("GPL");
Acked-by Jonathan Cameron on v1 1/2
#3 lore raw
In reply to [email protected]

Looks good to me. Adding my signoff:

Thanks,
Laxman

-----Original Message-----
From: Andrew Chew=20
Sent: Thursday, September 09, 2010 10:32 AM
To: [email protected]
Cc: [email protected]; [email protected]; Laxman Dewangan; Andrew Chew
Subject: [PATCH 1/2] iio: Change GAIN macros to SCALE.

From: Andrew Chew <[email protected]>

Per email exchange with Jonathan Cameron, GAIN should instead be SCALE, t= o
be consistent with documentation.

Resending, since this goes with the 2/2 patch.

---
=20drivers/staging/iio/magnetometer/magnet.h | 12 ++++++------
=201 files changed, 6 insertions(+), 6 deletions(-)

drivers/staging/= renamed from drivers/staging/iio/magnetometer/magnet.h +0 -0

iio/magnetometer/magnet.h
index 6433830..1260eb7 100644

drivers/staging/iio/magnetometer/magnet.h +0 -0
@@ -12,14 +12,14 @@

=20#define IIO_DEV_ATTR_MAGN_Z_OFFSET(_mode, _show, _store, _addr) \
=20 IIO_DEVICE_ATTR(magn_z_offset, _mode, _show, _store, _addr)
=20
-#define IIO_DEV_ATTR_MAGN_X_GAIN(_mode, _show, _store, _addr) \
- IIO_DEVICE_ATTR(magn_x_gain, _mode, _show, _store, _addr)
+#define IIO_DEV_ATTR_MAGN_X_SCALE(_mode, _show, _store, _addr) \
+ IIO_DEVICE_ATTR(magn_x_scale, _mode, _show, _store, _addr)
=20
-#define IIO_DEV_ATTR_MAGN_Y_GAIN(_mode, _show, _store, _addr) \
- IIO_DEVICE_ATTR(magn_y_gain, _mode, _show, _store, _addr)
+#define IIO_DEV_ATTR_MAGN_Y_SCALE(_mode, _show, _store, _addr) \
+ IIO_DEVICE_ATTR(magn_y_scale, _mode, _show, _store, _addr)
=20
-#define IIO_DEV_ATTR_MAGN_Z_GAIN(_mode, _show, _store, _addr) \
- IIO_DEVICE_ATTR(magn_z_gain, _mode, _show, _store, _addr)
+#define IIO_DEV_ATTR_MAGN_Z_SCALE(_mode, _show, _store, _addr) \
+ IIO_DEVICE_ATTR(magn_z_scale, _mode, _show, _store, _addr)
=20
=20#define IIO_DEV_ATTR_MAGN_X(_show, _addr) \
=20 IIO_DEVICE_ATTR(magn_x_raw, S_IRUGO, _show, NULL, _addr)
--=20
1.7.0.4

-------------------------------------------------------------------------=
----------
This email message is for the sole use of the intended recipient(s) and m= ay contain
confidential information. Any unauthorized review, use, disclosure or di= stribution
is prohibited. If you are not the intended recipient, please contact the= =20sender by
reply email and destroy all copies of the original message.
-------------------------------------------------------------------------=
----------