Updating SPEAr Support

index 8ba1ccf..2143d17 100644
@@ -115,6 +115,13 @@ extern unsigned int user_debug;
 #define vectors_high()	(0)
 #endif
 
+#if __LINUX_ARM_ARCH__ >= 7 ||		\
+	(__LINUX_ARM_ARCH__ == 6 && defined(CONFIG_CPU_32v6K))
+#define sev()	__asm__ __volatile__ ("sev" : : : "memory")
+#define wfe()	__asm__ __volatile__ ("wfe" : : : "memory")
+#define wfi()	__asm__ __volatile__ ("wfi" : : : "memory")
+#endif
+
 #if __LINUX_ARM_ARCH__ >= 7
 #define isb() __asm__ __volatile__ ("isb" : : : "memory")
 #define dsb() __asm__ __volatile__ ("dsb" : : : "memory")

index 9e9f70e..c338efab 100644
@@ -23,6 +23,7 @@
 #include <asm/cacheflush.h>
 #include <asm/localtimer.h>
 #include <asm/smp_scu.h>
+#include <asm/system.h>
 #include <mach/hardware.h>
 #include <mach/omap4-common.h>
 

index a101f10..6e3bafd 100644
@@ -52,6 +52,9 @@
 
 static inline void sysctl_soft_reset(void __iomem *base)
 {
+	/* switch to slow mode */
+	writel(0x2, base + SCCTRL);
+
 	/* writing any value to SCSYSSTAT reg will reset system */
 	writel(0, base + SCSYSSTAT);
 }

index af7e02c..c16d2f8 100644
@@ -40,7 +40,6 @@ void __init clk_init(void);
 void __init spear3xx_map_io(void);
 void __init spear3xx_init_irq(void);
 void __init spear3xx_init(void);
-void spear_pmx_init(struct pmx_driver *pmx_driver, uint base, uint size);
 
 /* pad mux declarations */
 #define PMX_FIRDA_MASK		(1 << 14)

@@ -133,8 +132,6 @@ extern struct pmx_dev pmx_telecom_sdio_4bit;
 extern struct pmx_dev pmx_telecom_sdio_8bit;
 extern struct pmx_dev pmx_gpio1;
 
-void spear300_pmx_init(void);
-
 /* Add spear300 machine function declarations here */
 void __init spear300_init(void);
 

@@ -154,8 +151,6 @@ extern struct pmx_dev pmx_fsmc;
 extern struct pmx_dev pmx_rs485_0_1;
 extern struct pmx_dev pmx_tdm0;
 
-void spear310_pmx_init(void);
-
 /* Add spear310 machine function declarations here */
 void __init spear310_init(void);
 

@@ -195,8 +190,6 @@ extern struct pmx_dev pmx_smii0;
 extern struct pmx_dev pmx_smii1;
 extern struct pmx_dev pmx_i2c1;
 
-void spear320_pmx_init(void);
-
 /* Add spear320 machine function declarations here */
 void __init spear320_init(void);
 

index 3560f8c..19c2daf 100644
@@ -459,10 +459,16 @@ void __init spear300_init(void)
 		if (ret)
 			printk(KERN_ERR "Error registering Shared IRQ\n");
 	}
-}
 
-void spear300_pmx_init(void)
-{
-	spear_pmx_init(&pmx_driver, SPEAR300_SOC_CONFIG_BASE,
+	/* pmx initialization */
+	pmx_driver.base = ioremap(SPEAR300_SOC_CONFIG_BASE,
 			SPEAR300_SOC_CONFIG_SIZE);
+	if (pmx_driver.base) {
+		ret = pmx_register(&pmx_driver);
+		if (ret)
+			printk(KERN_ERR "padmux: registeration failed. err no"
+					": %d\n", ret);
+		/* Free Mapping, device selection already done */
+		iounmap(pmx_driver.base);
+	}
 }

index bb21db1..2c90663 100644
@@ -51,14 +51,13 @@ static void __init spear300_evb_init(void)
 {
 	unsigned int i;
 
-	/* call spear300 machine init function */
-	spear300_init();
-
-	/* padmux initialization */
+	/* padmux initialization, must be done before spear300_init */
 	pmx_driver.mode = &photo_frame_mode;
 	pmx_driver.devs = pmx_devs;
 	pmx_driver.devs_count = ARRAY_SIZE(pmx_devs);
-	spear300_pmx_init();
+
+	/* call spear300 machine init function */
+	spear300_init();
 
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));

index 96a1ab8..576bc57 100644
@@ -293,10 +293,11 @@ void __init spear310_init(void)
 		if (ret)
 			printk(KERN_ERR "Error registering Shared IRQ 4\n");
 	}
-}
 
-void spear310_pmx_init(void)
-{
-	spear_pmx_init(&pmx_driver, SPEAR310_SOC_CONFIG_BASE,
-			SPEAR310_SOC_CONFIG_SIZE);
+	/* pmx initialization */
+	pmx_driver.base = base;
+	ret = pmx_register(&pmx_driver);
+	if (ret)
+		printk(KERN_ERR "padmux: registeration failed. err no: %d\n",
+				ret);
 }

index 7facf66..4e55e55 100644
@@ -58,14 +58,13 @@ static void __init spear310_evb_init(void)
 {
 	unsigned int i;
 
-	/* call spear310 machine init function */
-	spear310_init();
-
-	/* padmux initialization */
+	/* padmux initialization, must be done before spear310_init */
 	pmx_driver.mode = NULL;
 	pmx_driver.devs = pmx_devs;
 	pmx_driver.devs_count = ARRAY_SIZE(pmx_devs);
-	spear310_pmx_init();
+
+	/* call spear310 machine init function */
+	spear310_init();
 
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));

index 6a12195..2886bb2 100644
@@ -540,10 +540,11 @@ void __init spear320_init(void)
 		if (ret)
 			printk(KERN_ERR "Error registering Shared IRQ 4\n");
 	}
-}
 
-void spear320_pmx_init(void)
-{
-	spear_pmx_init(&pmx_driver, SPEAR320_SOC_CONFIG_BASE,
-			SPEAR320_SOC_CONFIG_SIZE);
+	/* pmx initialization */
+	pmx_driver.base = base;
+	ret = pmx_register(&pmx_driver);
+	if (ret)
+		printk(KERN_ERR "padmux: registeration failed. err no: %d\n",
+				ret);
 }

index 62ac685..7083a06 100644
@@ -55,14 +55,13 @@ static void __init spear320_evb_init(void)
 {
 	unsigned int i;
 
-	/* call spear320 machine init function */
-	spear320_init();
-
-	/* padmux initialization */
+	/* padmux initialization, must be done before spear320_init */
 	pmx_driver.mode = &auto_net_mii_mode;
 	pmx_driver.devs = pmx_devs;
 	pmx_driver.devs_count = ARRAY_SIZE(pmx_devs);
-	spear320_pmx_init();
+
+	/* call spear320 machine init function */
+	spear320_init();
 
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));

index e87313a..efd2e17 100644
@@ -525,24 +525,3 @@ struct pmx_dev pmx_plgpio_45_46_49_50 = {
 };
 
 #endif
-
-/* spear padmux initialization function */
-void spear_pmx_init(struct pmx_driver *pmx_driver, uint base, uint size)
-{
-	int ret = 0;
-
-	/* pad mux initialization */
-	pmx_driver->base = ioremap(base, size);
-	if (!pmx_driver->base) {
-		ret = -ENOMEM;
-		goto pmx_fail;
-	}
-
-	ret = pmx_register(pmx_driver);
-	iounmap(pmx_driver->base);
-
-pmx_fail:
-	if (ret)
-		printk(KERN_ERR "padmux: registeration failed. err no: %d\n",
-				ret);
-}

index 18febf9..7ea8749 100644
@@ -39,10 +39,25 @@ static struct clk rtc_clk = {
 };
 
 /* clock derived from 24 MHz osc clk */
+/* pll masks structure */
+static struct pll_clk_masks pll1_masks = {
+	.mode_mask = PLL_MODE_MASK,
+	.mode_shift = PLL_MODE_SHIFT,
+	.norm_fdbk_m_mask = PLL_NORM_FDBK_M_MASK,
+	.norm_fdbk_m_shift = PLL_NORM_FDBK_M_SHIFT,
+	.dith_fdbk_m_mask = PLL_DITH_FDBK_M_MASK,
+	.dith_fdbk_m_shift = PLL_DITH_FDBK_M_SHIFT,
+	.div_p_mask = PLL_DIV_P_MASK,
+	.div_p_shift = PLL_DIV_P_SHIFT,
+	.div_n_mask = PLL_DIV_N_MASK,
+	.div_n_shift = PLL_DIV_N_SHIFT,
+};
+
 /* pll1 configuration structure */
 static struct pll_clk_config pll1_config = {
 	.mode_reg = PLL1_CTR,
 	.cfg_reg = PLL1_FRQ,
+	.masks = &pll1_masks,
 };
 
 /* PLL1 clock */

@@ -50,7 +65,7 @@ static struct clk pll1_clk = {
 	.pclk = &osc_24m_clk,
 	.en_reg = PLL1_CTR,
 	.en_reg_bit = PLL_ENABLE,
-	.recalc = &pll1_clk_recalc,
+	.recalc = &pll_clk_recalc,
 	.private_data = &pll1_config,
 };
 

@@ -76,11 +91,16 @@ static struct clk cpu_clk = {
 	.recalc = &follow_parent,
 };
 
+/* ahb masks structure */
+static struct bus_clk_masks ahb_masks = {
+	.mask = PLL_HCLK_RATIO_MASK,
+	.shift = PLL_HCLK_RATIO_SHIFT,
+};
+
 /* ahb configuration structure */
 static struct bus_clk_config ahb_config = {
 	.reg = CORE_CLK_CFG,
-	.mask = PLL_HCLK_RATIO_MASK,
-	.shift = PLL_HCLK_RATIO_SHIFT,
+	.masks = &ahb_masks,
 };
 
 /* ahb clock */

@@ -91,9 +111,22 @@ static struct clk ahb_clk = {
 	.private_data = &ahb_config,
 };
 
+/* auxiliary synthesizers masks */
+static struct aux_clk_masks aux_masks = {
+	.eq_sel_mask = AUX_EQ_SEL_MASK,
+	.eq_sel_shift = AUX_EQ_SEL_SHIFT,
+	.eq1_mask = AUX_EQ1_SEL,
+	.eq2_mask = AUX_EQ2_SEL,
+	.xscale_sel_mask = AUX_XSCALE_MASK,
+	.xscale_sel_shift = AUX_XSCALE_SHIFT,
+	.yscale_sel_mask = AUX_YSCALE_MASK,
+	.yscale_sel_shift = AUX_YSCALE_SHIFT,
+};
+
 /* uart configurations */
 static struct aux_clk_config uart_config = {
 	.synth_reg = UART_CLK_SYNT,
+	.masks = &aux_masks,
 };
 
 /* uart parents */

@@ -130,6 +163,7 @@ static struct clk uart_clk = {
 /* firda configurations */
 static struct aux_clk_config firda_config = {
 	.synth_reg = FIRDA_CLK_SYNT,
+	.masks = &aux_masks,
 };
 
 /* firda parents */

@@ -184,9 +218,18 @@ static struct pclk_sel gpt_pclk_sel = {
 	.pclk_sel_mask = GPT_CLK_MASK,
 };
 
+/* gpt synthesizer masks */
+static struct gpt_clk_masks gpt_masks = {
+	.mscale_sel_mask = GPT_MSCALE_MASK,
+	.mscale_sel_shift = GPT_MSCALE_SHIFT,
+	.nscale_sel_mask = GPT_NSCALE_MASK,
+	.nscale_sel_shift = GPT_NSCALE_SHIFT,
+};
+
 /* gpt0 configurations */
-static struct aux_clk_config gpt0_config = {
+static struct gpt_clk_config gpt0_config = {
 	.synth_reg = PRSC1_CLK_CFG,
+	.masks = &gpt_masks,
 };
 
 /* gpt0 timer clock */

@@ -199,8 +242,9 @@ static struct clk gpt0_clk = {
 };
 
 /* gpt1 configurations */
-static struct aux_clk_config gpt1_config = {
+static struct gpt_clk_config gpt1_config = {
 	.synth_reg = PRSC2_CLK_CFG,
+	.masks = &gpt_masks,
 };
 
 /* gpt1 timer clock */

@@ -214,8 +258,9 @@ static struct clk gpt1_clk = {
 };
 
 /* gpt2 configurations */
-static struct aux_clk_config gpt2_config = {
+static struct gpt_clk_config gpt2_config = {
 	.synth_reg = PRSC3_CLK_CFG,
+	.masks = &gpt_masks,
 };
 
 /* gpt2 timer clock */

@@ -253,11 +298,16 @@ static struct clk clcd_clk = {
 };
 
 /* clock derived from ahb clk */
+/* apb masks structure */
+static struct bus_clk_masks apb_masks = {
+	.mask = HCLK_PCLK_RATIO_MASK,
+	.shift = HCLK_PCLK_RATIO_SHIFT,
+};
+
 /* apb configuration structure */
 static struct bus_clk_config apb_config = {
 	.reg = CORE_CLK_CFG,
-	.mask = HCLK_PCLK_RATIO_MASK,
-	.shift = HCLK_PCLK_RATIO_SHIFT,
+	.masks = &apb_masks,
 };
 
 /* apb clock */

144 lines not on this page · raw message

141 lines not on this page · raw message

96 lines not on this page · raw message

index c16d2f8..e7d2de8 100644
@@ -33,10 +33,11 @@
 /* Add spear3xx family device structure declarations here */
 extern struct amba_device gpio_device;
 extern struct amba_device uart_device;
-extern struct sys_timer spear_sys_timer;
+extern struct sys_timer spear3xx_timer;
 
 /* Add spear3xx family function declarations here */
 void __init clk_init(void);
+void __init spear_setup_timer(void);
 void __init spear3xx_map_io(void);
 void __init spear3xx_init_irq(void);
 void __init spear3xx_init(void);

index 2c90663..cd23c98 100644
@@ -71,6 +71,6 @@ MACHINE_START(SPEAR300, "ST-SPEAR300-EVB")
 	.boot_params	=	0x00000100,
 	.map_io		=	spear3xx_map_io,
 	.init_irq	=	spear3xx_init_irq,
-	.timer		=	&spear_sys_timer,
+	.timer		=	&spear3xx_timer,
 	.init_machine	=	spear300_evb_init,
 MACHINE_END

index 4e55e55..3855431 100644
@@ -78,6 +78,6 @@ MACHINE_START(SPEAR310, "ST-SPEAR310-EVB")
 	.boot_params	=	0x00000100,
 	.map_io		=	spear3xx_map_io,
 	.init_irq	=	spear3xx_init_irq,
-	.timer		=	&spear_sys_timer,
+	.timer		=	&spear3xx_timer,
 	.init_machine	=	spear310_evb_init,
 MACHINE_END

index 7083a06..4a7ce35 100644
@@ -75,6 +75,6 @@ MACHINE_START(SPEAR320, "ST-SPEAR320-EVB")
 	.boot_params	=	0x00000100,
 	.map_io		=	spear3xx_map_io,
 	.init_irq	=	spear3xx_init_irq,
-	.timer		=	&spear_sys_timer,
+	.timer		=	&spear3xx_timer,
 	.init_machine	=	spear320_evb_init,
 MACHINE_END

index efd2e17..34de574 100644
@@ -523,5 +523,35 @@ struct pmx_dev pmx_plgpio_45_46_49_50 = {
 	.mode_count = ARRAY_SIZE(pmx_plgpio_45_46_49_50_modes),
 	.enb_on_reset = 1,
 };
+#endif /* CONFIG_MACH_SPEAR310 || CONFIG_MACH_SPEAR320 */
 
-#endif
+static void __init spear3xx_timer_init(void)
+{
+	char pclk_name[] = "pll3_48m_clk";
+	struct clk *gpt_clk, *pclk;
+
+	/* get the system timer clock */
+	gpt_clk = clk_get_sys("gpt0", NULL);
+	if (!gpt_clk) {
+		pr_err("%s:couldn't get clk for gpt\n", __func__);
+		BUG();
+	}
+
+	/* get the suitable parent clock for timer*/
+	pclk = clk_get(NULL, pclk_name);
+	if (!pclk) {
+		pr_err("%s:couldn't get %s as parent for gpt\n",
+				__func__, pclk_name);
+		BUG();
+	}
+
+	clk_set_parent(gpt_clk, pclk);
+	clk_put(gpt_clk);
+	clk_put(pclk);
+
+	spear_setup_timer();
+}
+
+struct sys_timer spear3xx_timer = {
+	.init = spear3xx_timer_init,
+};

index 16205a5..e5967ed 100644
@@ -31,9 +31,10 @@
 /* Add spear6xx family device structure declarations here */
 extern struct amba_device gpio_device[];
 extern struct amba_device uart_device[];
-extern struct sys_timer spear_sys_timer;
+extern struct sys_timer spear6xx_timer;
 
 /* Add spear6xx family function declarations here */
+void __init spear_setup_timer(void);
 void __init spear6xx_map_io(void);
 void __init spear6xx_init_irq(void);
 void __init spear6xx_init(void);

index daff8d0..bdd5b76 100644
@@ -42,10 +42,11 @@ static void __init spear600_evb_init(void)
 		amba_device_register(amba_devs[i], &iomem_resource);
 }
 
+
 MACHINE_START(SPEAR600, "ST-SPEAR600-EVB")
 	.boot_params	=	0x00000100,
 	.map_io		=	spear6xx_map_io,
 	.init_irq	=	spear6xx_init_irq,
-	.timer		=	&spear_sys_timer,
+	.timer		=	&spear6xx_timer,
 	.init_machine	=	spear600_evb_init,
 MACHINE_END

index baf6bcc..e0bf51e 100644
@@ -155,3 +155,34 @@ void __init spear6xx_map_io(void)
 	/* This will initialize clock framework */
 	clk_init();
 }
+
+static void __init spear6xx_timer_init(void)
+{
+	char pclk_name[] = "pll3_48m_clk";
+	struct clk *gpt_clk, *pclk;
+
+	/* get the system timer clock */
+	gpt_clk = clk_get_sys("gpt0", NULL);
+	if (!gpt_clk) {
+		pr_err("%s:couldn't get clk for gpt\n", __func__);
+		BUG();
+	}
+
+	/* get the suitable parent clock for timer*/
+	pclk = clk_get(NULL, pclk_name);
+	if (!pclk) {
+		pr_err("%s:couldn't get %s as parent for gpt\n",
+				__func__, pclk_name);
+		BUG();
+	}
+
+	clk_set_parent(gpt_clk, pclk);
+	clk_put(gpt_clk);
+	clk_put(pclk);
+
+	spear_setup_timer();
+}
+
+struct sys_timer spear6xx_timer = {
+	.init = spear6xx_timer_init,
+};

index ab21165..7a038c9 100644
@@ -1,7 +1,7 @@
 /*
  * arch/arm/plat-spear/time.c
  *
- * Copyright (C) 2009 ST Microelectronics
+ * Copyright (C) 2010 ST Microelectronics
  * Shiraz Hashim<[email protected]>
  *
  * This file is licensed under the terms of the GNU General Public

@@ -215,7 +215,7 @@ static void __init spear_clockevent_init(void)
 
 void __init spear_setup_timer(void)
 {
-	struct clk *pll3_clk;
+	int ret;
 
 	if (!request_mem_region(SPEAR_GPT0_BASE, SZ_1K, "gpt0")) {
 		pr_err("%s:cannot get IO addr\n", __func__);

@@ -234,26 +234,21 @@ void __init spear_setup_timer(void)
 		goto err_iomap;
 	}
 
-	pll3_clk = clk_get(NULL, "pll3_48m_clk");
-	if (!pll3_clk) {
-		pr_err("%s:couldn't get PLL3 as parent for gpt\n", __func__);
-		goto err_iomap;
+	ret = clk_enable(gpt_clk);
+	if (ret < 0) {
+		pr_err("%s:couldn't enable gpt clock\n", __func__);
+		goto err_clk;
 	}
 
-	clk_set_parent(gpt_clk, pll3_clk);
-
 	spear_clockevent_init();
 	spear_clocksource_init();
 
 	return;
 
+err_clk:
+	clk_put(gpt_clk);
 err_iomap:
 	iounmap(gpt_base);
-
 err_mem:
 	release_mem_region(SPEAR_GPT0_BASE, SZ_1K);
 }
-
-struct sys_timer spear_sys_timer = {
-	.init = spear_setup_timer,
-};

new file mode 100644
index 0000000..effdb81
@@ -0,0 +1,19 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/clkdev.h
+ *
+ * Clock Dev framework definitions for spear13xx machine family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_CLKDEV_H
+#define __MACH_CLKDEV_H
+
+#include <plat/clkdev.h>
+
+#endif /* __MACH_CLKDEV_H */

46 lines not on this page · raw message

new file mode 100644
index 0000000..43fa541
@@ -0,0 +1,19 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/gpio.h
+ *
+ * GPIO macros for spear13xx machine family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_GPIO_H
+#define __MACH_GPIO_H
+
+#include <plat/gpio.h>
+
+#endif /* __MACH_GPIO_H */

new file mode 100644
index 0000000..0047d75
@@ -0,0 +1,25 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/hardware.h
+ *
+ * Hardware definitions for spear13xx machine family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_HARDWARE_H
+#define __MACH_HARDWARE_H
+
+#include <mach/spear.h>
+
+/* Vitual to physical translation of statically mapped space */
+#define IO_ADDRESS(x)		(x | 0xF0000000)
+
+/* typesafe io address */
+#define __io_address(n)		__io(IO_ADDRESS(n))
+
+#endif /* __MACH_HARDWARE_H */

new file mode 100644
index 0000000..2fe3503
@@ -0,0 +1,19 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/io.h
+ *
+ * IO definitions for spear13xx machine family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_IO_H
+#define __MACH_IO_H
+
+#include <plat/io.h>
+
+#endif /* __MACH_IO_H */

91 lines not on this page · raw message

new file mode 100644
index 0000000..200257c
@@ -0,0 +1,19 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/memory.h
+ *
+ * Memory map for spear13xx machine family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_MEMORY_H
+#define __MACH_MEMORY_H
+
+#include <plat/memory.h>
+
+#endif /* __MACH_MEMORY_H */

306 lines not on this page · raw message

new file mode 100644
index 0000000..6e028a1
@@ -0,0 +1,33 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/smp.h
+ *
+ * Few SMP related definitions for spear13xx machine family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_SMP_H
+#define __MACH_SMP_H
+
+#include <asm/hardware/gic.h>
+
+#define hard_smp_processor_id()			\
+	({						\
+		unsigned int cpunum;			\
+		__asm__("mrc p15, 0, %0, c0, c0, 5"	\
+			: "=r" (cpunum));		\
+		cpunum &= 0x0F;				\
+	})
+
+/* We use IRQ1 as the IPI */
+static inline void smp_cross_call(const struct cpumask *mask)
+{
+	gic_raise_softirq(mask, 1);
+}
+
+#endif

93 lines not on this page · raw message

new file mode 100644
index 0000000..b3ba267
@@ -0,0 +1,21 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/spear1300.h
+ *
+ * SPEAr1300 Machine specific definition
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifdef	CONFIG_MACH_SPEAR1300
+
+#ifndef __MACH_SPEAR1300_H
+#define __MACH_SPEAR1300_H
+
+#endif /* __MACH_SPEAR1300_H */
+
+#endif /* CONFIG_MACH_SPEAR1300 */

new file mode 100644
index 0000000..4f976c2
@@ -0,0 +1,39 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/system.h
+ *
+ * spear13xx Machine family specific architecture functions
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_SYSTEM_H
+#define __MACH_SYSTEM_H
+
+#include <linux/io.h>
+#include <mach/hardware.h>
+#include <mach/misc_regs.h>
+
+static inline void arch_idle(void)
+{
+	/*
+	 * This should do all the clock switching
+	 * and wait for interrupt tricks
+	 */
+	cpu_do_idle();
+}
+
+static inline void arch_reset(char mode, const char *cmd)
+{
+	writel(0x01, SYS_SW_RES);
+
+	/* wait for system to rest */
+	while (1)
+		;
+}
+
+#endif /* __MACH_SYSTEM_H */

new file mode 100644
index 0000000..0a81490
@@ -0,0 +1,19 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/timex.h
+ *
+ * spear13xx machine family specific timex definitions
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_TIMEX_H
+#define __MACH_TIMEX_H
+
+#define CLOCK_TICK_RATE			24000000
+
+#endif /* __MACH_TIMEX_H */

new file mode 100644
index 0000000..3c27f25
@@ -0,0 +1,19 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/uncompress.h
+ *
+ * Serial port stubs for kernel decompress status messages
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_UNCOMPRESS_H
+#define __MACH_UNCOMPRESS_H
+
+#include <plat/uncompress.h>
+
+#endif /* __MACH_UNCOMPRESS_H */

new file mode 100644
index 0000000..85ad57e
@@ -0,0 +1,18 @@
+/*
+ * arch/arm/mach-spear13xx/include/mach/vmalloc.h
+ *
+ * Defining Vmalloc area for spear13xx machine family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_VMALLOC_H
+#define __MACH_VMALLOC_H
+
+#include <plat/vmalloc.h>
+
+#endif /* __MACH_VMALLOC_H */

index e08b58c..4788669 100644
@@ -15,8 +15,8 @@
 #define __PLAT_CLOCK_H
 
 #include <linux/list.h>
-#include <asm/clkdev.h>
 #include <linux/types.h>
+#include <asm/clkdev.h>
 
 /* clk structure flags */
 #define	ALWAYS_ENABLED		(1 << 0) /* clock always enabled */

index 55a4e40..d52db68 100644
@@ -14,8 +14,8 @@
 #ifndef __PLAT_SYSTEM_H
 #define __PLAT_SYSTEM_H
 
-#include <asm/hardware/sp810.h>
 #include <linux/io.h>
+#include <asm/hardware/sp810.h>
 #include <mach/spear.h>
 
 static inline void arch_idle(void)

353 lines not on this page · raw message

index 9ecc6b2..5c0f042 100644
@@ -29,7 +29,7 @@
 #define SPEAR_GPT0_CHAN1_IRQ	IRQ_GPT0_TMR1
 
 /* Add spear13xx family device structure declarations here */
-extern struct amba_device uart_device;
+extern struct amba_device spear13xx_uart_device;
 extern struct sys_timer spear13xx_timer;
 
 /* Add spear1300 machine device structure declarations here */

new file mode 100644
index 0000000..816b08c
@@ -0,0 +1,25 @@
+/*
+ * arch/arm/mach-spear13xx/localtimer.c
+ * Directly picked from realview
+ *
+ * Copyright (C) 2010 ST Microelectronics Ltd.
+ * Shiraz Hashim <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <linux/clockchips.h>
+#include <asm/irq.h>
+#include <asm/smp_twd.h>
+#include <asm/localtimer.h>
+
+/* Setup the local clock events for a CPU. */
+void __cpuinit local_timer_setup(struct clock_event_device *evt)
+{
+	evt->irq = IRQ_LOCALTIMER;
+	twd_timer_setup(evt);
+}

200 lines not on this page · raw message

new file mode 100644
index 0000000..c1b82f1
@@ -0,0 +1,23 @@
+/*
+ * arch/arm/mach-spear13xx/spear1300.c
+ *
+ * SPEAr1300 machine source file
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Shiraz Hashim <[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <mach/generic.h>
+#include <mach/spear.h>
+
+/* Add spear1300 specific devices here */
+
+void __init spear1300_init(void)
+{
+	/* call spear13xx family common init function */
+	spear13xx_init();
+}

48 lines not on this page · raw message

121 lines not on this page · raw message

index e7d2de8..1c8f9f1 100644
@@ -100,6 +100,7 @@ extern struct pmx_driver pmx_driver;
 /* spear300 declarations */
 #ifdef CONFIG_MACH_SPEAR300
 /* Add spear300 machine device structure declarations here */
+extern struct amba_device clcd_device;
 extern struct amba_device gpio1_device;
 
 /* pad mux modes */

@@ -136,6 +137,8 @@ extern struct pmx_dev pmx_gpio1;
 /* Add spear300 machine function declarations here */
 void __init spear300_init(void);
 
+/* Add misc structure declarations here */
+extern struct clcd_board clcd_plat_data;
 #endif /* CONFIG_MACH_SPEAR300 */
 
 /* spear310 declarations */

@@ -160,6 +163,7 @@ void __init spear310_init(void);
 /* spear320 declarations */
 #ifdef CONFIG_MACH_SPEAR320
 /* Add spear320 machine device structure declarations here */
+extern struct amba_device clcd_device;
 
 /* pad mux modes */
 extern struct pmx_mode auto_net_smii_mode;

@@ -194,6 +198,8 @@ extern struct pmx_dev pmx_i2c1;
 /* Add spear320 machine function declarations here */
 void __init spear320_init(void);
 
+/* Add misc structure declarations here */
+extern struct clcd_board clcd_plat_data;
 #endif /* CONFIG_MACH_SPEAR320 */
 
 #endif /* __MACH_GENERIC_H */

index 19c2daf..fb7d5f1 100644
@@ -371,6 +371,23 @@ struct pmx_driver pmx_driver = {
 };
 
 /* Add spear300 specific devices here */
+
+/* CLCD device registration */
+struct amba_device clcd_device = {
+	.dev = {
+		.init_name = "clcd",
+		.coherent_dma_mask = ~0,
+		.platform_data = &clcd_plat_data,
+	},
+	.res = {
+		.start = SPEAR300_CLCD_BASE,
+		.end = SPEAR300_CLCD_BASE + SPEAR300_CLCD_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	.dma_mask = ~0,
+	.irq = {IRQ_CLCD, NO_IRQ},
+};
+
 /* arm gpio1 device registeration */
 static struct pl061_platform_data gpio1_plat_data = {
 	.gpio_base	= 8,

index cd23c98..3bb7fbc 100644
@@ -38,6 +38,7 @@ static struct amba_device *amba_devs[] __initdata = {
 	&uart_device,
 
 	/* spear300 specific devices */
+	&clcd_device,
 	&gpio1_device,
 };
 

index 2886bb2..e5baa00 100644
@@ -386,6 +386,22 @@ struct pmx_driver pmx_driver = {
 
 /* Add spear320 specific devices here */
 
+/* CLCD device registration */
+struct amba_device clcd_device = {
+	.dev = {
+		.init_name = "clcd",
+		.coherent_dma_mask = ~0,
+		.platform_data = &clcd_plat_data,
+	},
+	.res = {
+		.start = SPEAR320_CLCD_BASE,
+		.end = SPEAR320_CLCD_BASE + SPEAR320_CLCD_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	.dma_mask = ~0,
+	.irq = {VIRQ_CLCD, NO_IRQ},
+};
+
 /* spear3xx shared irq */
 struct shirq_dev_config shirq_ras1_config[] = {
 	{

index 4a7ce35..821e806 100644
@@ -43,6 +43,7 @@ static struct amba_device *amba_devs[] __initdata = {
 	&uart_device,
 
 	/* spear320 specific devices */
+	&clcd_device,
 };
 
 static struct platform_device *plat_devs[] __initdata = {

index e5967ed..d6a04f2 100644
@@ -29,6 +29,7 @@
 #define SPEAR_GPT0_CHAN1_IRQ	IRQ_CPU_GPT1_2
 
 /* Add spear6xx family device structure declarations here */
+extern struct amba_device clcd_device;
 extern struct amba_device gpio_device[];
 extern struct amba_device uart_device[];
 extern struct sys_timer spear6xx_timer;

@@ -43,4 +44,7 @@ void __init clk_init(void);
 
 /* Add spear600 machine device structure declarations here */
 
+/* Add misc structure declarations here */
+extern struct clcd_board clcd_plat_data;
+
 #endif /* __MACH_GENERIC_H */

index bdd5b76..88e69f4 100644
@@ -17,6 +17,7 @@
 #include <mach/spear.h>
 
 static struct amba_device *amba_devs[] __initdata = {
+	&clcd_device,
 	&gpio_device[0],
 	&gpio_device[1],
 	&gpio_device[2],

index e0bf51e..ebb504f 100644
@@ -23,6 +23,23 @@
 #include <mach/spear.h>
 
 /* Add spear6xx machines common devices here */
+
+/* CLCD device registration */
+struct amba_device clcd_device = {
+	.dev = {
+		.init_name = "clcd",
+		.coherent_dma_mask = ~0,
+		.platform_data = &clcd_plat_data,
+	},
+	.res = {
+		.start = SPEAR6XX_ICM3_CLCD_BASE,
+		.end = SPEAR6XX_ICM3_CLCD_BASE + SPEAR6XX_ICM3_CLCD_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	.dma_mask = ~0,
+	.irq = {IRQ_BASIC_CLCD, NO_IRQ},
+};
+
 /* uart device registeration */
 struct amba_device uart_device[] = {
 	{

114 lines not on this page · raw message

index 722f634..ca80c46 100644
@@ -53,10 +53,10 @@ static struct clk rtc_clk = {
 static struct pclk_info pll_pclk_info[] = {
 	{
 		.pclk = &osc1_24m_clk,
-		.pclk_mask = OSC_24M_MASK,
+		.pclk_val = OSC_24M_VAL,
 	}, {
 		.pclk = &osc3_25m_clk,
-		.pclk_mask = OSC_25M_MASK,
+		.pclk_val = OSC_25M_VAL,
 	},
 };
 

@@ -88,16 +88,45 @@ static struct pll_clk_config pll1_config = {
 	.masks = &pll_masks,
 };
 
+/* pll rate configuration table, in ascending order of rates */
+struct pll_rate_tbl pll_rtbl[] = {
+	/* PCLK 24MHz */
+	{.mode = 0, .m = 0x7D, .n = 0x03, .p = 0x2}, /* 500 MHz */
+	{.mode = 0, .m = 0xA6, .n = 0x03, .p = 0x2}, /* 664 MHz */
+	{.mode = 0, .m = 0xC8, .n = 0x03, .p = 0x2}, /* 800 MHz */
+	{.mode = 0, .m = 0xFA, .n = 0x06, .p = 0x1}, /* 1000 MHz */
+};
+
 /* pll1 clock */
 static struct clk pll1_clk = {
+	.flags = ENABLED_ON_INIT,
 	.pclk_sel = &pll_pclk_sel,
 	.pclk_sel_shift = PLL1_CLK_SHIFT,
 	.en_reg = PLL1_CTR,
 	.en_reg_bit = PLL_ENABLE,
+	.calc_rate = &pll_calc_rate,
 	.recalc = &pll_clk_recalc,
+	.set_rate = &pll_clk_set_rate,
+	.rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 3},
 	.private_data = &pll1_config,
 };
 
+/* pll1div2 clock */
+static struct clk pll1div2_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk = &pll1_clk,
+	.div_factor = 2,
+	.recalc = &follow_parent,
+};
+
+/* pll1div4 clock */
+static struct clk pll1div4_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk = &pll1_clk,
+	.div_factor = 4,
+	.recalc = &follow_parent,
+};
+
 /* pll2 configuration structure */
 static struct pll_clk_config pll2_config = {
 	.mode_reg = PLL2_CTR,

@@ -111,7 +140,10 @@ static struct clk pll2_clk = {
 	.pclk_sel_shift = PLL2_CLK_SHIFT,
 	.en_reg = PLL2_CTR,
 	.en_reg_bit = PLL_ENABLE,
+	.calc_rate = &pll_calc_rate,
 	.recalc = &pll_clk_recalc,
+	.set_rate = &pll_clk_set_rate,
+	.rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 3},
 	.private_data = &pll2_config,
 };
 

@@ -128,7 +160,10 @@ static struct clk pll3_clk = {
 	.pclk_sel_shift = PLL3_CLK_SHIFT,
 	.en_reg = PLL3_CTR,
 	.en_reg_bit = PLL_ENABLE,
+	.calc_rate = &pll_calc_rate,
 	.recalc = &pll_clk_recalc,
+	.set_rate = &pll_clk_set_rate,
+	.rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 3},
 	.private_data = &pll3_config,
 };
 

@@ -139,12 +174,24 @@ static struct pll_clk_config pll4_config = {
 	.masks = &pll_masks,
 };
 
+/* pll4 rate configuration table, in ascending order of rates */
+struct pll_rate_tbl pll4_rtbl[] = {
+	{.mode = 0, .m = 0x7D, .n = 0x03, .p = 0x2}, /* 500 MHz */
+	{.mode = 0, .m = 0xA6, .n = 0x03, .p = 0x2}, /* 664 MHz */
+	{.mode = 0, .m = 0xC8, .n = 0x03, .p = 0x2}, /* 800 MHz */
+	{.mode = 0, .m = 0xFA, .n = 0x06, .p = 0x1}, /* 1000 MHz */
+};
+
 /* pll4 (DDR) clock */
 static struct clk pll4_clk = {
+	.flags = ENABLED_ON_INIT,
 	.pclk = &osc1_24m_clk,
 	.en_reg = PLL4_CTR,
 	.en_reg_bit = PLL_ENABLE,
+	.calc_rate = &pll_calc_rate,
 	.recalc = &pll_clk_recalc,
+	.set_rate = &pll_clk_set_rate,
+	.rate_config = {pll4_rtbl, ARRAY_SIZE(pll4_rtbl), 3},
 	.private_data = &pll4_config,
 };
 

@@ -192,10 +239,10 @@ static struct clk apb_clk = {
 static struct pclk_info gpt_pclk_info[] = {
 	{
 		.pclk = &osc1_24m_clk,
-		.pclk_mask = GPT_OSC24_MASK,
+		.pclk_val = GPT_OSC24_VAL,
 	}, {
 		.pclk = &apb_clk,
-		.pclk_mask = GPT_APB_MASK,
+		.pclk_val = GPT_APB_VAL,
 	},
 };
 

@@ -246,15 +293,8 @@ static struct clk gpt3_clk = {
 /* watch dog timer clock */
 static struct clk wdt_clk = {
 	.flags = ALWAYS_ENABLED,
-	.pclk = &apb_clk,
-	.recalc = &follow_parent,
-};
-
-/* smi clock */
-static struct clk smi_clk = {
-	.pclk = &ahb_clk,
-	.en_reg = PERIP1_CLK_ENB,
-	.en_reg_bit = SMI_CLK_ENB,
+	.pclk = &cpu_clk,
+	.div_factor = 2,
 	.recalc = &follow_parent,
 };
 

@@ -270,22 +310,42 @@ static struct aux_clk_masks aux_masks = {
 	.yscale_sel_shift = AUX_YSCALE_SHIFT,
 };
 
+/* clocks derived multiple parents (pll1, pll5, synthesizers or others) */
 /* uart configurations */
-static struct aux_clk_config uart_config = {
+static struct aux_clk_config uart_synth_config = {
 	.synth_reg = UART_CLK_SYNT,
 	.masks = &aux_masks,
 };
 
-/* clocks derived from pll1 or pll5 */
+/* aux rate configuration table, in ascending order of rates */
+struct aux_rate_tbl aux_rtbl[] = {
+	/* For PLL1div2 = 500 MHz */
+	{.xscale = 1, .yscale = 6, .eq = 1}, /* 83 MHz */
+	{.xscale = 1, .yscale = 4, .eq = 1}, /* 125 MHz */
+	{.xscale = 1, .yscale = 3, .eq = 1}, /* 166 MHz */
+	{.xscale = 1, .yscale = 2, .eq = 1}, /* 250 MHz */
+};
+
+/* uart synth clock */
+static struct clk uart_synth_clk = {
+	.en_reg = UART_CLK_SYNT,
+	.en_reg_bit = AUX_SYNT_ENB,
+	.pclk = &pll1div2_clk,
+	.calc_rate = &aux_calc_rate,
+	.recalc = &aux_clk_recalc,
+	.set_rate = &aux_clk_set_rate,
+	.rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 0},
+	.private_data = &uart_synth_config,
+};
+
 /* uart parents */
 static struct pclk_info uart_pclk_info[] = {
 	{
 		.pclk = &pll5_clk,
-		.pclk_mask = AUX_CLK_PLL5_MASK,
+		.pclk_val = AUX_CLK_PLL5_VAL,
 	}, {
-		.pclk = &pll1_clk,
-		.pclk_mask = AUX_CLK_PLL1_MASK,
-		.scalable = 1,
+		.pclk = &uart_synth_clk,
+		.pclk_val = AUX_CLK_SYNT_VAL,
 	},
 };
 

@@ -303,10 +363,469 @@ static struct clk uart_clk = {
 	.en_reg_bit = UART_CLK_ENB,
 	.pclk_sel = &uart_pclk_sel,
 	.pclk_sel_shift = UART_CLK_SHIFT,
+	.recalc = &follow_parent,
+};
+
+/* sdhci configurations */
+static struct aux_clk_config sdhci_synth_config = {
+	.synth_reg = SDHCI_CLK_SYNT,
+	.masks = &aux_masks,
+};
+
+/* sdhci synth clock */
+static struct clk sdhci_synth_clk = {
+	.en_reg = SDHCI_CLK_SYNT,
+	.en_reg_bit = AUX_SYNT_ENB,
+	.pclk = &pll1div2_clk,
+	.calc_rate = &aux_calc_rate,
 	.recalc = &aux_clk_recalc,
-	.private_data = &uart_config,
+	.set_rate = &aux_clk_set_rate,
+	.rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 2},
+	.private_data = &sdhci_synth_config,
+};
+
+/* sdhci clock */
+static struct clk sdhci_clk = {
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = SDHCI_CLK_ENB,
+	.pclk = &sdhci_synth_clk,
+	.recalc = &follow_parent,
+};
+
+/* cfxd configurations */
+static struct aux_clk_config cfxd_synth_config = {
+	.synth_reg = CFXD_CLK_SYNT,
+	.masks = &aux_masks,
+};
+
+/* cfxd synth clock */
+static struct clk cfxd_synth_clk = {
+	.en_reg = CFXD_CLK_SYNT,
+	.en_reg_bit = AUX_SYNT_ENB,
+	.pclk = &pll1div2_clk,
+	.calc_rate = &aux_calc_rate,
+	.recalc = &aux_clk_recalc,
+	.set_rate = &aux_clk_set_rate,
+	.rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 2},
+	.private_data = &cfxd_synth_config,
+};
+
+/* cfxd clock */
+static struct clk cfxd_clk = {
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = CFXD_CLK_ENB,
+	.pclk = &cfxd_synth_clk,
+	.recalc = &follow_parent,
 };
 
+/* C3 clk configurations */
+static struct aux_clk_config c3_synth_config = {
+	.synth_reg = C3_CLK_SYNT,
+	.masks = &aux_masks,
+};
+
+/* c3 synth clock */
+static struct clk c3_synth_clk = {
+	.en_reg = C3_CLK_SYNT,
+	.en_reg_bit = AUX_SYNT_ENB,
+	.pclk = &pll1div2_clk,
+	.calc_rate = &aux_calc_rate,
+	.recalc = &aux_clk_recalc,
+	.set_rate = &aux_clk_set_rate,
+	.rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 0},
+	.private_data = &c3_synth_config,
+};
+
+/* c3 parents */
+static struct pclk_info c3_pclk_info[] = {
+	{
+		.pclk = &pll5_clk,
+		.pclk_val = AUX_CLK_PLL5_VAL,
+	}, {
+		.pclk = &c3_synth_clk,
+		.pclk_val = AUX_CLK_SYNT_VAL,
+	},
+};
+
+/* c3 parent select structure */
+static struct pclk_sel c3_pclk_sel = {
+	.pclk_info = c3_pclk_info,
+	.pclk_count = ARRAY_SIZE(c3_pclk_info),
+	.pclk_sel_reg = PERIP_CLK_CFG,
+	.pclk_sel_mask = C3_CLK_MASK,
+};
+
+/* c3 clock */
+static struct clk c3_clk = {
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = C3_CLK_ENB,
+	.pclk_sel = &c3_pclk_sel,
+	.pclk_sel_shift = C3_CLK_SHIFT,
+	.recalc = &follow_parent,
+};
+
+/* gmac phy clk configurations */
+static struct aux_clk_config gmac_phy_synth_config = {
+	.synth_reg = GMAC_CLK_SYNT,
+	.masks = &aux_masks,
+};
+
+/* gmii external pad clock for phy operation */
+static struct clk gmii_txclk125_pad = {
+	.flags = ALWAYS_ENABLED,
+	.rate = 125000000,
+};
+
+/* gmac phy set of input clks*/
+static struct pclk_info gmac_phy_input_pclk_info[] = {
+	{
+		.pclk = &gmii_txclk125_pad,
+		.pclk_val = GMAC_PHY_PAD_VAL,
+	}, {
+		.pclk = &pll2_clk,
+		.pclk_val = GMAC_PHY_PLL2_VAL,
+	}, {
+		.pclk = &osc3_25m_clk,
+		.pclk_val = GMAC_PHY_OSC3_VAL,
+	},
+};
+
+static struct pclk_sel gmac_phy_input_pclk_sel = {
+	.pclk_info = gmac_phy_input_pclk_info,
+	.pclk_count = ARRAY_SIZE(gmac_phy_input_pclk_info),
+	.pclk_sel_reg = GMAC_CLK_CFG,
+	.pclk_sel_mask = GMAC_PHY_INPUT_CLK_MASK,
+};
+
+static struct clk gmac_phy_input_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk_sel = &gmac_phy_input_pclk_sel,
+	.pclk_sel_shift = GMAC_PHY_INPUT_CLK_SHIFT,
+	.recalc = &follow_parent,
+};
+
+/* gmac rate configuration table, in ascending order of rates */
+struct aux_rate_tbl gmac_rtbl[] = {
+	/* For gmac phy input clk */
+	{.xscale = 1, .yscale = 6, .eq = 1}, /* divided by 6 */
+	{.xscale = 1, .yscale = 4, .eq = 1}, /* divided by 4 */
+	{.xscale = 1, .yscale = 3, .eq = 1}, /* divided by 3 */
+	{.xscale = 1, .yscale = 2, .eq = 1}, /* divided by 2 */
+};
+
+static struct clk gmac_phy_synth_clk = {
+	.en_reg = GMAC_CLK_CFG,
+	.en_reg_bit = GMAC_PHY_SYNT_ENB,
+	.pclk = &gmac_phy_input_clk,
+	.calc_rate = &aux_calc_rate,
+	.recalc = &aux_clk_recalc,
+	.set_rate = &aux_clk_set_rate,
+	.rate_config = {gmac_rtbl, ARRAY_SIZE(gmac_rtbl), 0},
+	.private_data = &gmac_phy_synth_config,
+};
+
+/* gmac phy parents */
+static struct pclk_info gmac_phy_pclk_info[] = {
+	{
+		.pclk = &gmac_phy_input_clk,
+		.pclk_val = 0,
+	}, {
+		.pclk = &gmac_phy_synth_clk,
+		.pclk_val = 1,
+	}
+};
+
+/* gmac phy parent select structure */
+static struct pclk_sel gmac_phy_pclk_sel = {
+	.pclk_info = gmac_phy_pclk_info,
+	.pclk_count = ARRAY_SIZE(gmac_phy_pclk_info),
+	.pclk_sel_reg = GMAC_CLK_CFG,
+	.pclk_sel_mask = GMAC_PHY_CLK_MASK,
+};
+
+/* gmac phy clock */
+static struct clk gmac_phy_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk_sel = &gmac_phy_pclk_sel,
+	.pclk_sel_shift = GMAC_PHY_CLK_SHIFT,
+	.recalc = &follow_parent,
+};
+
+/* clcd synthesizers masks */
+static struct clcd_synth_masks clcd_masks = {
+	.div_factor_mask = CLCD_SYNT_DIV_FACTOR_MASK,
+	.div_factor_shift = CLCD_SYNT_DIV_FACTOR_SHIFT,
+};
+
+static struct clcd_clk_config clcd_synth_config = {
+	.synth_reg = CLCD_CLK_SYNT,
+	.masks = &clcd_masks,
+};
+
+/* clcd synth parents */
+static struct pclk_info clcd_synth_pclk_info[] = {
+	{
+		.pclk = &pll1div4_clk,
+		.pclk_val = CLCD_SYNT_PLL1_DIV4_VAL,
+	}, {
+		.pclk = &pll2_clk,
+		.pclk_val = CLCD_SYNT_PLL2_VAL,
+	},
+};
+
+/* clcd synth parent select structure */
+static struct pclk_sel clcd_synth_pclk_sel = {
+	.pclk_info = clcd_synth_pclk_info,
+	.pclk_count = ARRAY_SIZE(clcd_synth_pclk_info),
+	.pclk_sel_reg = PLL_CFG,
+	.pclk_sel_mask = CLCD_SYNT_CLK_MASK,
+};
+
+/* clcd rate configuration table, in ascending order of rates */
+struct clcd_rate_tbl clcd_rtbl[] = {
+	/* For pll1div4 = 250 MHz */
+	{.div = 0x4000}, /* 62.5 MHz */
+	{.div = 0x2000}, /* 125 MHz */
+};
+
+/* clcd synth clock */
+static struct clk clcd_synth_clk = {
+	.en_reg = CLCD_CLK_SYNT,
+	.en_reg_bit = CLCD_SYNT_ENB,
+	.pclk_sel = &clcd_synth_pclk_sel,
+	.pclk_sel_shift = CLCD_SYNT_CLK_SHIFT,
+	.calc_rate = &clcd_calc_rate,
+	.recalc = &clcd_clk_recalc,
+	.set_rate = &clcd_clk_set_rate,
+	.rate_config = {clcd_rtbl, ARRAY_SIZE(clcd_rtbl), 1},
+	.private_data = &clcd_synth_config,
+};
+
+/* clcd clock parents */
+static struct pclk_info clcd_pclk_info[] = {
+	{
+		.pclk = &pll5_clk,
+		.pclk_val = AUX_CLK_PLL5_VAL,
+	}, {
+		.pclk = &clcd_synth_clk,
+		.pclk_val = AUX_CLK_SYNT_VAL,
+	},
+};
+
+/* clcd parent select structure */
+static struct pclk_sel clcd_pclk_sel = {
+	.pclk_info = clcd_pclk_info,
+	.pclk_count = ARRAY_SIZE(clcd_pclk_info),
+	.pclk_sel_reg = PERIP_CLK_CFG,
+	.pclk_sel_mask = CLCD_CLK_MASK,
+};
+
+/* clcd clock */
+static struct clk clcd_clk = {
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = CLCD_CLK_ENB,
+	.pclk_sel = &clcd_pclk_sel,
+	.pclk_sel_shift = CLCD_CLK_SHIFT,
+	.recalc = &follow_parent,
+};
+
+/* clock derived from ahb clk */
+
+/* i2c clock */
+static struct clk i2c_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = I2C_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* dma clock */
+static struct clk dma0_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = DMA0_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+static struct clk dma1_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = DMA1_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* jpeg clock */
+static struct clk jpeg_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = JPEG_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* gmac clock */
+static struct clk gmac_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = GMAC_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* fsmc clock */
+static struct clk fsmc_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = SMI_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* smi clock */
+static struct clk smi_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = SMI_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* uhc0 clock */
+static struct clk uhci0_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = UHC0_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* uhc1 clock */
+static struct clk uhci1_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = UHC1_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* usbd clock */
+static struct clk usbd_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = USBD_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* pci clocks */
+static struct clk pcie0_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = PCIE0_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+static struct clk pcie1_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = PCIE1_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+static struct clk pcie2_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = PCIE2_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* sysram clocks */
+static struct clk sysram0_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = SYSRAM0_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+static struct clk sysram1_clk = {
+	.pclk = &ahb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = SYSRAM1_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* clock derived from apb clk */
+/* adc clock */
+static struct clk adc_clk = {
+	.pclk = &apb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = ADC_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* ssp clock */
+static struct clk ssp_clk = {
+	.pclk = &apb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = SSP_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* gpio clock */
+static struct clk gpio0_clk = {
+	.pclk = &apb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = GPIO0_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* gpio clock */
+static struct clk gpio1_clk = {
+	.pclk = &apb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = GPIO1_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* i2s0 clock */
+static struct clk i2s0_clk = {
+	.pclk = &apb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = I2S0_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* i2s1 clock */
+static struct clk i2s1_clk = {
+	.pclk = &apb_clk,
+	.en_reg = PERIP1_CLK_ENB,
+	.en_reg_bit = I2S1_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* keyboard clock */
+static struct clk kbd_clk = {
+	.pclk = &apb_clk,
+	.en_reg = PERIP2_CLK_ENB,
+	.en_reg_bit = KBD_CLK_ENB,
+	.recalc = &follow_parent,
+};
+
+/* spear1300 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1300
+
+#endif
+
+/* spear1310 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1310
+/* can0 clock */
+static struct clk can0_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk = &apb_clk,
+	.recalc = &follow_parent,
+};
+
+/* can1 clock */
+static struct clk can1_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk = &apb_clk,
+	.recalc = &follow_parent,
+};
+#endif
+
 /* array of all spear 13xx clock lookups */
 static struct clk_lookup spear_clk_lookups[] = {
 	/* root clks */

@@ -315,7 +834,7 @@ static struct clk_lookup spear_clk_lookups[] = {
 	{.con_id = "osc3_25m_clk",	.clk = &osc3_25m_clk},
 
 	/* clock derived from 32 KHz osc clk */
-	{.dev_id = "rtc",		.clk = &rtc_clk},
+	{.dev_id = "rtc-spear",		.clk = &rtc_clk},
 
 	/* clock derived from 24/25 MHz osc1/osc3 clk */
 	{.con_id = "pll1_clk",		.clk = &pll1_clk},

@@ -328,18 +847,68 @@ static struct clk_lookup spear_clk_lookups[] = {
 	/* clock derived from pll1 clk */
 	{.con_id = "cpu_clk",		.clk = &cpu_clk},
 	{.con_id = "ahb_clk",		.clk = &ahb_clk},
-	{ .con_id = "apb_clk",		.clk = &apb_clk},
+	{.con_id = "apb_clk",		.clk = &apb_clk},
+
+	/* synthesizers/prescaled clocks */
+	{.con_id = "pll1div2_clk",		.clk = &pll1div2_clk},
+	{.con_id = "pll1div4_clk",		.clk = &pll1div4_clk},
+	{.con_id = "c3_synth_clk",		.clk = &c3_synth_clk},
+	{.con_id = "gmii_txclk123_pad_clk",	.clk = &gmii_txclk125_pad},
+	{.con_id = "clcd_synth_clk",		.clk = &clcd_synth_clk},
+	{.con_id = "uart_synth_clk",		.clk = &uart_synth_clk},
+	{.con_id = "sdhci_synth_clk",		.clk = &sdhci_synth_clk},
+	{.con_id = "cfxd_synth_clk",		.clk = &cfxd_synth_clk},
+	{.con_id = "gmac_phy_input_clk",	.clk = &gmac_phy_input_clk},
+	{.con_id = "gmac_phy_synth_clk",	.clk = &gmac_phy_synth_clk},
+	{.con_id = "gmac_phy_clk",		.clk = &gmac_phy_clk},
 
 	/* clocks having multiple parent source from above clocks */
-	{.dev_id = "uart",		.clk = &uart_clk},
+	{.dev_id = "clcd",		.clk = &clcd_clk},
 	{.dev_id = "gpt0",		.clk = &gpt0_clk},
 	{.dev_id = "gpt1",		.clk = &gpt1_clk},
 	{.dev_id = "gpt2",		.clk = &gpt2_clk},
 	{.dev_id = "gpt3",		.clk = &gpt3_clk},
+	{.dev_id = "uart",		.clk = &uart_clk},
 
-	/* clock derived from ahb/apb clk */
-	{ .dev_id = "smi",		.clk = &smi_clk},
-	{ .dev_id = "wdt",		.clk = &wdt_clk},
+	/* clock derived from ahb clk */
+	{.dev_id = "smi",		.clk = &smi_clk},
+	{.con_id = "usbh.0_clk",	.clk = &uhci0_clk},
+	{.con_id = "usbh.1_clk",	.clk = &uhci1_clk},
+	{.dev_id = "usbd",		.clk = &usbd_clk},
+	{.dev_id = "i2c_designware.0",	.clk = &i2c_clk},
+	{.dev_id = "dma0",		.clk = &dma0_clk},
+	{.dev_id = "dma1",		.clk = &dma1_clk},
+	{.dev_id = "jpeg",		.clk = &jpeg_clk},
+	{.dev_id = "gmac",		.clk = &gmac_clk},
+	{.dev_id = "c3",		.clk = &c3_clk},
+	{.dev_id = "pcie0",		.clk = &pcie0_clk},
+	{.dev_id = "pcie1",		.clk = &pcie1_clk},
+	{.dev_id = "pcie2",		.clk = &pcie2_clk},
+	{.dev_id = "cfxd",		.clk = &cfxd_clk},
+	{.dev_id = "sdhci",		.clk = &sdhci_clk},
+	{.con_id = "fsmc",		.clk = &fsmc_clk},
+	{.dev_id = "sysram0",		.clk = &sysram0_clk},
+	{.dev_id = "sysram1",		.clk = &sysram1_clk},
+
+	/* clock derived from apb clk */
+	{.dev_id = "i2s0",		.clk = &i2s0_clk},
+	{.dev_id = "i2s1",		.clk = &i2s1_clk},
+	{.dev_id = "adc",		.clk = &adc_clk},
+	{.dev_id = "ssp-pl022",		.clk = &ssp_clk},
+	{.dev_id = "gpio0",		.clk = &gpio0_clk},
+	{.dev_id = "gpio1",		.clk = &gpio1_clk},
+	{.dev_id = "keyboard",		.clk = &kbd_clk},
+	{.dev_id = "wdt",		.clk = &wdt_clk},
+
+	/* spear1300 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1300
+#endif
+
+	/* spear1310 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1310
+	{.dev_id = "spear_can.0",	.clk = &can0_clk},
+	{.dev_id = "spear_can.1",	.clk = &can1_clk},
+#endif
 };
 
 void __init clk_init(void)

149 lines not on this page · raw message

588 lines not on this page · raw message

index 38d767a..6cb4f3c 100644
@@ -63,8 +63,8 @@
 #define GPT1_CLK_SHIFT		11
 #define GPT2_CLK_SHIFT		12
 #define GPT_CLK_MASK		0x1
-#define AUX_CLK_PLL3_MASK	0
-#define AUX_CLK_PLL1_MASK	1
+#define AUX_CLK_PLL3_VAL	0
+#define AUX_CLK_PLL1_VAL	1
 
 #define PERIP1_CLK_ENB		((unsigned int *)(MISC_BASE + 0x02C))
 /* PERIP1_CLK_ENB register masks */

@@ -113,6 +113,7 @@
 #define RAS3_CLK_SYNT		((unsigned int *)(MISC_BASE + 0x074))
 #define RAS4_CLK_SYNT		((unsigned int *)(MISC_BASE + 0x078))
 /* aux clk synthesiser register masks for irda to ras4 */
+#define AUX_SYNT_ENB		31
 #define AUX_EQ_SEL_SHIFT	30
 #define AUX_EQ_SEL_MASK		1
 #define AUX_EQ1_SEL		0

487 lines not on this page · raw message

index 0390803..bd71e72 100644
@@ -66,8 +66,8 @@
 #define GPT2_CLK_SHIFT		11
 #define GPT3_CLK_SHIFT		12
 #define GPT_CLK_MASK		0x1
-#define AUX_CLK_PLL3_MASK	0
-#define AUX_CLK_PLL1_MASK	1
+#define AUX_CLK_PLL3_VAL	0
+#define AUX_CLK_PLL1_VAL	1
 
 #define PERIP1_CLK_ENB		((unsigned int *)(MISC_BASE + 0x02C))
 /* PERIP1_CLK_ENB register masks */

@@ -123,6 +123,7 @@
 #define RAS3_CLK_SYNT		((unsigned int *)(MISC_BASE + 0x074))
 #define RAS4_CLK_SYNT		((unsigned int *)(MISC_BASE + 0x078))
 /* aux clk synthesiser register masks for irda to ras4 */
+#define AUX_SYNT_ENB		31
 #define AUX_EQ_SEL_SHIFT	30
 #define AUX_EQ_SEL_MASK		1
 #define AUX_EQ1_SEL		0

844 lines not on this page · raw message

154 lines not on this page · raw message

index 8de7cf6..7d3338f 100644
@@ -13,6 +13,7 @@
 
 #include <linux/bug.h>
 #include <linux/clk.h>
+#include <linux/debugfs.h>
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/list.h>

@@ -22,8 +23,14 @@
 
 static DEFINE_SPINLOCK(clocks_lock);
 static LIST_HEAD(root_clks);
+#ifdef CONFIG_DEBUG_FS
+static LIST_HEAD(clocks);
+#endif
 
 static void propagate_rate(struct clk *, int on_init);
+#ifdef CONFIG_DEBUG_FS
+static int clk_debugfs_reparent(struct clk *);
+#endif
 
 static int generic_clk_enable(struct clk *clk)
 {

@@ -96,6 +103,10 @@ static void clk_reparent(struct clk *clk, struct pclk_info *pclk_info)
 
 	clk->pclk = pclk_info->pclk;
 	spin_unlock_irqrestore(&clocks_lock, flags);
+
+#ifdef CONFIG_DEBUG_FS
+	clk_debugfs_reparent(clk);
+#endif
 }
 
 static void do_clk_disable(struct clk *clk)

@@ -336,6 +347,12 @@ void clk_register(struct clk_lookup *cl)
 
 	spin_unlock_irqrestore(&clocks_lock, flags);
 
+	/* debugfs specific */
+#ifdef CONFIG_DEBUG_FS
+	list_add(&clk->node, &clocks);
+	clk->cl = cl;
+#endif
+
 	/* add clock to arm clockdev framework */
 	clkdev_add(cl);
 }

@@ -855,3 +872,102 @@ void recalc_root_clocks(void)
 	}
 	spin_unlock_irqrestore(&clocks_lock, flags);
 }
+
+#ifdef CONFIG_DEBUG_FS
+/*
+ *	debugfs support to trace clock tree hierarchy and attributes
+ */
+static struct dentry *clk_debugfs_root;
+static int clk_debugfs_register_one(struct clk *c)
+{
+	int err;
+	struct dentry *d, *child;
+	struct clk *pa = c->pclk;
+	char s[255];
+	char *p = s;
+
+	if (c) {
+		if (c->cl->con_id)
+			p += sprintf(p, "%s", c->cl->con_id);
+		if (c->cl->dev_id)
+			p += sprintf(p, "%s", c->cl->dev_id);
+	}
+	d = debugfs_create_dir(s, pa ? pa->dent : clk_debugfs_root);
+	if (!d)
+		return -ENOMEM;
+	c->dent = d;
+
+	d = debugfs_create_u32("usage_count", S_IRUGO, c->dent,
+			(u32 *)&c->usage_count);
+	if (!d) {
+		err = -ENOMEM;
+		goto err_out;
+	}
+	d = debugfs_create_u32("rate", S_IRUGO, c->dent, (u32 *)&c->rate);
+	if (!d) {
+		err = -ENOMEM;
+		goto err_out;
+	}
+	d = debugfs_create_x32("flags", S_IRUGO, c->dent, (u32 *)&c->flags);
+	if (!d) {
+		err = -ENOMEM;
+		goto err_out;
+	}
+	return 0;
+
+err_out:
+	d = c->dent;
+	list_for_each_entry(child, &d->d_subdirs, d_u.d_child)
+		debugfs_remove(child);
+	debugfs_remove(c->dent);
+	return err;
+}
+
+static int clk_debugfs_register(struct clk *c)
+{
+	int err;
+	struct clk *pa = c->pclk;
+
+	if (pa && !pa->dent) {
+		err = clk_debugfs_register(pa);
+		if (err)
+			return err;
+	}
+
+	if (!c->dent) {
+		err = clk_debugfs_register_one(c);
+		if (err)
+			return err;
+	}
+	return 0;
+}
+
+static int __init clk_debugfs_init(void)
+{
+	struct clk *c;
+	struct dentry *d;
+	int err;
+
+	d = debugfs_create_dir("clock", NULL);
+	if (!d)
+		return -ENOMEM;
+	clk_debugfs_root = d;
+
+	list_for_each_entry(c, &clocks, node) {
+		err = clk_debugfs_register(c);
+		if (err)
+			goto err_out;
+	}
+	return 0;
+err_out:
+	debugfs_remove_recursive(clk_debugfs_root);
+	return err;
+}
+late_initcall(clk_debugfs_init);
+
+static int clk_debugfs_reparent(struct clk *c)
+{
+	debugfs_remove(c->dent);
+	return clk_debugfs_register_one(c);
+}
+#endif /* CONFIG_DEBUG_FS */

index f7b4b5a..621c17c 100644
@@ -88,6 +88,9 @@ struct rate_config {
  * @children: list for childrens or this clock
  * @sibling: node for list of clocks having same parents
  * @private_data: clock specific private data
+ * @node: list to maintain clocks linearly
+ * @cl: clocklook up assoicated with this clock
+ * @dent: object for debugfs
  */
 struct clk {
 	unsigned int usage_count;

@@ -109,6 +112,11 @@ struct clk {
 	struct list_head children;
 	struct list_head sibling;
 	void *private_data;
+#ifdef CONFIG_DEBUG_FS
+	struct list_head node;
+	struct clk_lookup *cl;
+	struct dentry *dent;
+#endif
 };
 
 /* pll configuration structure */

index cacf17a..53677e4 100644
@@ -62,7 +62,7 @@
 #define SPEAR320_SMII1_BASE		0xAB000000
 #define SPEAR320_SMII1_SIZE		0x01000000
 
-#define SPEAR320_SOC_CONFIG_BASE	0xB4000000
+#define SPEAR320_SOC_CONFIG_BASE	0xB3000000
 #define SPEAR320_SOC_CONFIG_SIZE	0x00000070
 /* Interrupt registers offsets and masks */
 #define INT_STS_MASK_REG		0x04

index 1c8f9f1..d76ee98 100644
@@ -144,6 +144,7 @@ extern struct clcd_board clcd_plat_data;
 /* spear310 declarations */
 #ifdef CONFIG_MACH_SPEAR310
 /* Add spear310 machine device structure declarations here */
+extern struct platform_device plgpio_device;
 
 /* pad mux devices */
 extern struct pmx_dev pmx_emi_cs_0_1_4_5;

@@ -164,6 +165,7 @@ void __init spear310_init(void);
 #ifdef CONFIG_MACH_SPEAR320
 /* Add spear320 machine device structure declarations here */
 extern struct amba_device clcd_device;
+extern struct platform_device plgpio_device;
 
 /* pad mux modes */
 extern struct pmx_mode auto_net_smii_mode;

145 lines not on this page · raw message

index 7f940b8..f1175b9 100644
@@ -141,12 +141,13 @@
 #endif
 
 /* PLGPIO Virtual IRQs */
+#define SPEAR_PLGPIO_COUNT	102
 #if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
-#define SPEAR_PLGPIO_INT_BASE			(SPEAR_GPIO_INT_BASE + 8)
-#define SPEAR_GPIO_INT_END			(SPEAR_PLGPIO_INT_BASE + 102)
+#define SPEAR_PLGPIO_INT_BASE	(SPEAR_GPIO_INT_BASE + 8)
+#define SPEAR_GPIO_INT_END	(SPEAR_PLGPIO_INT_BASE + SPEAR_PLGPIO_COUNT)
 #endif
 
-#define VIRQ_END				SPEAR_GPIO_INT_END
-#define NR_IRQS					VIRQ_END
+#define VIRQ_END		SPEAR_GPIO_INT_END
+#define NR_IRQS			VIRQ_END
 
 #endif /* __MACH_IRQS_H */

81 lines not on this page · raw message

index 3855431..7dd93bd 100644
@@ -52,6 +52,7 @@ static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
 
 	/* spear310 specific devices */
+	&plgpio_device,
 };
 
 static void __init spear310_evb_init(void)

index e5baa00..2e388dd 100644
@@ -15,6 +15,7 @@
 #include <asm/irq.h>
 #include <mach/generic.h>
 #include <mach/spear.h>
+#include <plat/gpio.h>
 #include <plat/shirq.h>
 
 /* pad multiplexing support */

@@ -385,7 +386,6 @@ struct pmx_driver pmx_driver = {
 };
 
 /* Add spear320 specific devices here */
-
 /* CLCD device registration */
 struct amba_device clcd_device = {
 	.dev = {

@@ -402,6 +402,34 @@ struct amba_device clcd_device = {
 	.irq = {VIRQ_CLCD, NO_IRQ},
 };
 
+/* plgpio device registeration */
+static struct plgpio_platform_data plgpio_plat_data = {
+	.gpio_base = 8,
+	.irq_base = SPEAR_PLGPIO_INT_BASE,
+	.gpio_count = SPEAR_PLGPIO_COUNT,
+};
+
+static struct resource plgpio_resources[] = {
+	{
+		.start = SPEAR320_SOC_CONFIG_BASE,
+		.end = SPEAR320_SOC_CONFIG_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = VIRQ_PLGPIO,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device plgpio_device = {
+	.name = "plgpio",
+	.id = -1,
+	.dev = {
+		.platform_data = &plgpio_plat_data,
+	},
+	.num_resources = ARRAY_SIZE(plgpio_resources),
+	.resource = plgpio_resources,
+};
+
 /* spear3xx shared irq */
 struct shirq_dev_config shirq_ras1_config[] = {
 	{

index 821e806..82f4e76 100644
@@ -50,6 +50,7 @@ static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
 
 	/* spear320 specific devices */
+	&plgpio_device,
 };
 
 static void __init spear320_evb_init(void)

index 3a789db..465b2e7 100644
@@ -16,4 +16,31 @@
 
 #include <plat/gpio.h>
 
+#define CPU_GPIO_0		0
+#define CPU_GPIO_1		1
+#define CPU_GPIO_2		2
+#define CPU_GPIO_3		3
+#define CPU_GPIO_4		4
+#define CPU_GPIO_5		5
+#define CPU_GPIO_6		6
+#define CPU_GPIO_7		7
+
+#define BASIC_GPIO_0		8
+#define BASIC_GPIO_1		9
+#define BASIC_GPIO_2		10
+#define BASIC_GPIO_3		11
+#define BASIC_GPIO_4		12
+#define BASIC_GPIO_5		13
+#define BASIC_GPIO_6		14
+#define BASIC_GPIO_7		15
+
+#define APPL_GPIO_0		16
+#define APPL_GPIO_1		17
+#define APPL_GPIO_2		18
+#define APPL_GPIO_3		19
+#define APPL_GPIO_4		20
+#define APPL_GPIO_5		21
+#define APPL_GPIO_6		22
+#define APPL_GPIO_7		23
+
 #endif /* __MACH_GPIO_H */

index b857c91..450671e 100644
@@ -21,4 +21,39 @@
 #define gpio_cansleep	__gpio_cansleep
 #define gpio_to_irq	__gpio_to_irq
 
+/* plgpio driver declarations */
+/*
+ * plgpio pins in all machines are not one to one mapped, bitwise with
+ * registers bits. These set of macros define register masks for which below
+ * functions (pin_to_offset and offset_to_pin) are required to be called.
+ */
+#define PTO_ENB_REG		0x001
+#define PTO_WDATA_REG		0x002
+#define PTO_DIR_REG		0x004
+#define PTO_IE_REG		0x008
+#define PTO_RDATA_REG		0x010
+#define PTO_MIS_REG		0x020
+
+/* functions for converting pin to correct offset in register and vice versa */
+/**
+ * struct plgpio_platform_data: plgpio driver platform data
+ *
+ * gpio_base: gpio start number of plgpios
+ * irq_base: irq number of plgpio0
+ * gpio_count: total count of plgpios
+ * p2o: function ptr for pin to offset conversion. This is required only for
+ * machines where mapping b/w pin and offset is not 1-to-1.
+ * o2p: function ptr for offset to pin conversion. This is required only for
+ * machines where mapping b/w pin and offset is not 1-to-1.
+ * p2o_regs: mask of registers for which p2o and o2p are applicable
+ */
+struct plgpio_platform_data {
+	u32 gpio_base;
+	u32 irq_base;
+	u32 gpio_count;
+	int (*p2o)(int pin);		/* pin_to_offset */
+	int (*o2p)(int offset);		/* offset_to_pin */
+	u32 p2o_regs;
+};
+
 #endif /* __PLAT_GPIO_H */

452 lines not on this page · raw message

594 lines not on this page · raw message

index 5c0f042..bf032f6 100644
@@ -30,6 +30,7 @@
 
 /* Add spear13xx family device structure declarations here */
 extern struct amba_device spear13xx_uart_device;
+extern struct platform_device spear13xx_rtc_device;
 extern struct sys_timer spear13xx_timer;
 
 /* Add spear1300 machine device structure declarations here */

index 9a83d61..2fce2ec 100644
@@ -22,6 +22,7 @@ static struct amba_device *amba_devs[] __initdata = {
 };
 
 static struct platform_device *plat_devs[] __initdata = {
+	&spear13xx_rtc_device,
 };
 
 static void __init spear1300_evb_init(void)

index 8e3cdb7..5de0fd9 100644
@@ -37,6 +37,25 @@ struct amba_device spear13xx_uart_device = {
 	.irq = {IRQ_UART, NO_IRQ},
 };
 
+/* rtc device registration */
+static struct resource rtc_resources[] = {
+	{
+		.start = SPEAR13XX_RTC_BASE,
+		.end = SPEAR13XX_RTC_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_RTC,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device spear13xx_rtc_device = {
+	.name = "rtc-spear",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(rtc_resources),
+	.resource = rtc_resources,
+};
+
 /* Do spear13xx familiy common initialization part here */
 void __init spear13xx_init(void)
 {

index d76ee98..408bb8d 100644
@@ -33,6 +33,7 @@
 /* Add spear3xx family device structure declarations here */
 extern struct amba_device gpio_device;
 extern struct amba_device uart_device;
+extern struct platform_device rtc_device;
 extern struct sys_timer spear3xx_timer;
 
 /* Add spear3xx family function declarations here */

index 3bb7fbc..392ee4a 100644
@@ -44,6 +44,7 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&rtc_device,
 
 	/* spear300 specific devices */
 };

index 7dd93bd..15ca8fc 100644
@@ -50,6 +50,7 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&rtc_device,
 
 	/* spear310 specific devices */
 	&plgpio_device,

index 82f4e76..48155cc 100644
@@ -48,6 +48,7 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&rtc_device,
 
 	/* spear320 specific devices */
 	&plgpio_device,

index 34de574..64147c9 100644
@@ -54,6 +54,25 @@ struct amba_device uart_device = {
 	.irq = {IRQ_UART, NO_IRQ},
 };
 
+/* rtc device registration */
+static struct resource rtc_resources[] = {
+	{
+		.start = SPEAR3XX_ICM3_RTC_BASE,
+		.end = SPEAR3XX_ICM3_RTC_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_BASIC_RTC,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device rtc_device = {
+	.name = "rtc-spear",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(rtc_resources),
+	.resource = rtc_resources,
+};
+
 /* Do spear3xx familiy common initialization part here */
 void __init spear3xx_init(void)
 {

index d6a04f2..674b16c 100644
@@ -32,6 +32,7 @@
 extern struct amba_device clcd_device;
 extern struct amba_device gpio_device[];
 extern struct amba_device uart_device[];
+extern struct platform_device rtc_device;
 extern struct sys_timer spear6xx_timer;
 
 /* Add spear6xx family function declarations here */

index 88e69f4..861e83d 100644
@@ -26,6 +26,7 @@ static struct amba_device *amba_devs[] __initdata = {
 };
 
 static struct platform_device *plat_devs[] __initdata = {
+	&rtc_device,
 };
 
 static void __init spear600_evb_init(void)

index ebb504f..45bc4ec 100644
@@ -121,6 +121,25 @@ struct amba_device gpio_device[] = {
 	}
 };
 
+/* rtc device registration */
+static struct resource rtc_resources[] = {
+	{
+		.start = SPEAR6XX_ICM3_RTC_BASE,
+		.end = SPEAR6XX_ICM3_RTC_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_BASIC_RTC,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device rtc_device = {
+	.name = "rtc-spear",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(rtc_resources),
+	.resource = rtc_resources,
+};
+
 /* This will add devices, and do machine specific tasks */
 void __init spear6xx_init(void)
 {

index bf032f6..b0e25be 100644
@@ -30,6 +30,7 @@
 
 /* Add spear13xx family device structure declarations here */
 extern struct amba_device spear13xx_uart_device;
+extern struct platform_device spear13xx_i2c_device;
 extern struct platform_device spear13xx_rtc_device;
 extern struct sys_timer spear13xx_timer;
 

@@ -37,6 +38,7 @@ extern struct sys_timer spear13xx_timer;
 
 /* Add spear13xx family function declarations here */
 void __init clk_init(void);
+void __init i2c_register_board_devices(void);
 void __init spear_setup_timer(void);
 void __init spear1300_init(void);
 void __init spear13xx_map_io(void);

index 2fce2ec..4c72b7a 100644
@@ -22,6 +22,7 @@ static struct amba_device *amba_devs[] __initdata = {
 };
 
 static struct platform_device *plat_devs[] __initdata = {
+	&spear13xx_i2c_device,
 	&spear13xx_rtc_device,
 };
 

@@ -32,6 +33,9 @@ static void __init spear1300_evb_init(void)
 	/* call spear1300 machine init function */
 	spear1300_init();
 
+	/* Register slave devices on the I2C buses */
+	i2c_register_board_devices();
+
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
 

index 5de0fd9..8acf9df 100644
@@ -24,6 +24,7 @@
 #include <mach/hardware.h>
 
 /* Add spear13xx machines common devices here */
+
 /* uart device registeration */
 struct amba_device spear13xx_uart_device = {
 	.dev = {

@@ -37,6 +38,28 @@ struct amba_device spear13xx_uart_device = {
 	.irq = {IRQ_UART, NO_IRQ},
 };
 
+/* i2c device registeration */
+static struct resource i2c_resources[] = {
+	{
+		.start = SPEAR13XX_I2C_BASE,
+		.end = SPEAR13XX_I2C_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_I2C,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device spear13xx_i2c_device = {
+	.name = "i2c_designware",
+	.id = 0,
+	.dev = {
+		.coherent_dma_mask = ~0,
+	},
+	.num_resources = ARRAY_SIZE(i2c_resources),
+	.resource = i2c_resources,
+};
+
 /* rtc device registration */
 static struct resource rtc_resources[] = {
 	{

index 408bb8d..162f33b 100644
@@ -33,11 +33,13 @@
 /* Add spear3xx family device structure declarations here */
 extern struct amba_device gpio_device;
 extern struct amba_device uart_device;
+extern struct platform_device i2c_device;
 extern struct platform_device rtc_device;
 extern struct sys_timer spear3xx_timer;
 
 /* Add spear3xx family function declarations here */
 void __init clk_init(void);
+void __init i2c_register_board_devices(void);
 void __init spear_setup_timer(void);
 void __init spear3xx_map_io(void);
 void __init spear3xx_init_irq(void);

@@ -166,6 +168,7 @@ void __init spear310_init(void);
 #ifdef CONFIG_MACH_SPEAR320
 /* Add spear320 machine device structure declarations here */
 extern struct amba_device clcd_device;
+extern struct platform_device i2c1_device;
 extern struct platform_device plgpio_device;
 
 /* pad mux modes */

index f1175b9..5ad7574 100644
@@ -133,7 +133,7 @@
 #define VIRQ_MII1_SMII1				(VIRQ_START + 13)
 #define VIRQ_WAKEUP_SMII0			(VIRQ_START + 14)
 #define VIRQ_WAKEUP_MII1_SMII1			(VIRQ_START + 15)
-#define VIRQ_I2C				(VIRQ_START + 16)
+#define VIRQ_I2C1				(VIRQ_START + 16)
 
 /* GPIO pins virtual irqs */
 #define SPEAR_GPIO_INT_BASE			(VIRQ_START + 17)

index 392ee4a..083f65c 100644
@@ -44,6 +44,7 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&i2c_device,
 	&rtc_device,
 
 	/* spear300 specific devices */

@@ -61,6 +62,9 @@ static void __init spear300_evb_init(void)
 	/* call spear300 machine init function */
 	spear300_init();
 
+	/* Register slave devices on the I2C buses */
+	i2c_register_board_devices();
+
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
 

index 15ca8fc..208a68ce1 100644
@@ -50,6 +50,7 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&i2c_device,
 	&rtc_device,
 
 	/* spear310 specific devices */

@@ -68,6 +69,9 @@ static void __init spear310_evb_init(void)
 	/* call spear310 machine init function */
 	spear310_init();
 
+	/* Register slave devices on the I2C buses */
+	i2c_register_board_devices();
+
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
 

index 2e388dd..bfb21ae 100644
@@ -409,6 +409,28 @@ static struct plgpio_platform_data plgpio_plat_data = {
 	.gpio_count = SPEAR_PLGPIO_COUNT,
 };
 
+/* i2c1 device registeration */
+static struct resource i2c1_resources[] = {
+	{
+		.start = SPEAR320_I2C_BASE,
+		.end = SPEAR320_I2C_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = VIRQ_I2C1 ,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device i2c1_device = {
+	.name = "i2c_designware",
+	.id = 1,
+	.dev = {
+		.coherent_dma_mask = ~0,
+	},
+	.num_resources = ARRAY_SIZE(i2c1_resources),
+	.resource = i2c1_resources,
+};
+
 static struct resource plgpio_resources[] = {
 	{
 		.start = SPEAR320_SOC_CONFIG_BASE,

@@ -535,7 +557,7 @@ struct shirq_dev_config shirq_intrcomm_ras_config[] = {
 		.status_mask = WAKEUP_MII1_SMII1_IRQ_MASK,
 		.clear_mask = WAKEUP_MII1_SMII1_IRQ_MASK,
 	}, {
-		.virq = VIRQ_I2C,
+		.virq = VIRQ_I2C1,
 		.status_mask = I2C1_IRQ_MASK,
 		.clear_mask = I2C1_IRQ_MASK,
 	},

index 48155cc..90d685e 100644
@@ -48,9 +48,11 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&i2c_device,
 	&rtc_device,
 
 	/* spear320 specific devices */
+	&i2c1_device,
 	&plgpio_device,
 };
 

@@ -66,6 +68,9 @@ static void __init spear320_evb_init(void)
 	/* call spear320 machine init function */
 	spear320_init();
 
+	/* Register slave devices on the I2C buses */
+	i2c_register_board_devices();
+
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
 

index 64147c9..22d172b 100644
@@ -54,6 +54,28 @@ struct amba_device uart_device = {
 	.irq = {IRQ_UART, NO_IRQ},
 };
 
+/* i2c device registeration */
+static struct resource i2c_resources[] = {
+	{
+		.start = SPEAR3XX_ICM1_I2C_BASE,
+		.end = SPEAR3XX_ICM1_I2C_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_I2C,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device i2c_device = {
+	.name = "i2c_designware",
+	.id = 0,
+	.dev = {
+		.coherent_dma_mask = ~0,
+	},
+	.num_resources = ARRAY_SIZE(i2c_resources),
+	.resource = i2c_resources,
+};
+
 /* rtc device registration */
 static struct resource rtc_resources[] = {
 	{

index 674b16c..44a2f99 100644
@@ -32,10 +32,12 @@
 extern struct amba_device clcd_device;
 extern struct amba_device gpio_device[];
 extern struct amba_device uart_device[];
+extern struct platform_device i2c_device;
 extern struct platform_device rtc_device;
 extern struct sys_timer spear6xx_timer;
 
 /* Add spear6xx family function declarations here */
+void __init i2c_register_board_devices(void);
 void __init spear_setup_timer(void);
 void __init spear6xx_map_io(void);
 void __init spear6xx_init_irq(void);

index 861e83d..6b0cf23 100644
@@ -26,6 +26,7 @@ static struct amba_device *amba_devs[] __initdata = {
 };
 
 static struct platform_device *plat_devs[] __initdata = {
+	&i2c_device,
 	&rtc_device,
 };
 

@@ -36,6 +37,9 @@ static void __init spear600_evb_init(void)
 	/* call spear600 machine init function */
 	spear600_init();
 
+	/* Register slave devices on the I2C buses */
+	i2c_register_board_devices();
+
 	/* Add Platform Devices */
 	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
 

index 45bc4ec..646098f 100644
@@ -121,6 +121,28 @@ struct amba_device gpio_device[] = {
 	}
 };
 
+/* i2c device registeration */
+static struct resource i2c_resources[] = {
+	{
+		.start = SPEAR6XX_ICM1_I2C_BASE,
+		.end = SPEAR6XX_ICM1_I2C_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_I2C,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device i2c_device = {
+	.name = "i2c_designware",
+	.id = 0,
+	.dev = {
+		.coherent_dma_mask = ~0,
+	},
+	.num_resources = ARRAY_SIZE(i2c_resources),
+	.resource = i2c_resources,
+};
+
 /* rtc device registration */
 static struct resource rtc_resources[] = {
 	{

new file mode 100644
index 0000000..a2473a8
@@ -0,0 +1,29 @@
+/*
+ * arch/arm/plat-spear/i2c_eval_board.c
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Rajeev Kumar<[email protected]>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+
+static struct i2c_board_info __initdata i2c_board_info[] = {
+	{
+		.type = "eeprom",
+		.addr = 0x50,
+	}, {
+		.type = "eeprom",
+		.addr = 0x51,
+	},
+};
+
+void __init i2c_register_board_devices(void)
+{
+	i2c_register_board_info(0, i2c_board_info,
+				ARRAY_SIZE(i2c_board_info));
+}

index 34a928d..2101725 100644
@@ -1197,6 +1197,11 @@ MODULE_LICENSE ("GPL");
 #define	PLATFORM_DRIVER		ehci_atmel_driver
 #endif
 
+#ifdef CONFIG_PLAT_SPEAR
+#include "ehci-spear.c"
+#define PLATFORM_DRIVER		spear_ehci_hcd_driver
+#endif
+
 #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
     !defined(XILINX_OF_PLATFORM_DRIVER)

211 lines not on this page · raw message

index c3b4ccc..8104fd3 100644
@@ -1075,6 +1075,11 @@ MODULE_LICENSE ("GPL");
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
 #endif
 
+#ifdef CONFIG_PLAT_SPEAR
+#include "ohci-spear.c"
+#define PLATFORM_DRIVER		spear_ohci_hcd_driver
+#endif
+
 #ifdef CONFIG_PPC_PS3
 #include "ohci-ps3.c"
 #define PS3_SYSTEM_BUS_DRIVER	ps3_ohci_driver

240 lines not on this page · raw message

index b0e25be..a75ed3a 100644
@@ -30,7 +30,11 @@
 
 /* Add spear13xx family device structure declarations here */
 extern struct amba_device spear13xx_uart_device;
+extern struct platform_device spear13xx_ehci0_device;
+extern struct platform_device spear13xx_ehci1_device;
 extern struct platform_device spear13xx_i2c_device;
+extern struct platform_device spear13xx_ohci0_device;
+extern struct platform_device spear13xx_ohci1_device;
 extern struct platform_device spear13xx_rtc_device;
 extern struct sys_timer spear13xx_timer;
 

index 4c72b7a..9f53361 100644
@@ -22,7 +22,11 @@ static struct amba_device *amba_devs[] __initdata = {
 };
 
 static struct platform_device *plat_devs[] __initdata = {
+	&spear13xx_ehci0_device,
+	&spear13xx_ehci1_device,
 	&spear13xx_i2c_device,
+	&spear13xx_ohci0_device,
+	&spear13xx_ohci1_device,
 	&spear13xx_rtc_device,
 };
 

112 lines not on this page · raw message

index 162f33b..3eb2737 100644
@@ -33,7 +33,10 @@
 /* Add spear3xx family device structure declarations here */
 extern struct amba_device gpio_device;
 extern struct amba_device uart_device;
+extern struct platform_device ehci_device;
 extern struct platform_device i2c_device;
+extern struct platform_device ohci0_device;
+extern struct platform_device ohci1_device;
 extern struct platform_device rtc_device;
 extern struct sys_timer spear3xx_timer;
 

index 083f65c..3b3c6ce 100644
@@ -44,7 +44,10 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&ehci_device,
 	&i2c_device,
+	&ohci0_device,
+	&ohci1_device,
 	&rtc_device,
 
 	/* spear300 specific devices */

index 208a68ce1..d523040 100644
@@ -50,7 +50,10 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&ehci_device,
 	&i2c_device,
+	&ohci0_device,
+	&ohci1_device,
 	&rtc_device,
 
 	/* spear310 specific devices */

index 90d685e..f90a9b8 100644
@@ -48,7 +48,10 @@ static struct amba_device *amba_devs[] __initdata = {
 
 static struct platform_device *plat_devs[] __initdata = {
 	/* spear3xx specific devices */
+	&ehci_device,
 	&i2c_device,
+	&ohci0_device,
+	&ohci1_device,
 	&rtc_device,
 
 	/* spear320 specific devices */

86 lines not on this page · raw message

index 44a2f99..3b15289 100644
@@ -32,7 +32,11 @@
 extern struct amba_device clcd_device;
 extern struct amba_device gpio_device[];
 extern struct amba_device uart_device[];
+extern struct platform_device ehci0_device;
+extern struct platform_device ehci1_device;
 extern struct platform_device i2c_device;
+extern struct platform_device ohci0_device;
+extern struct platform_device ohci1_device;
 extern struct platform_device rtc_device;
 extern struct sys_timer spear6xx_timer;
 

index 6b0cf23..b4dfd25 100644
@@ -26,7 +26,11 @@ static struct amba_device *amba_devs[] __initdata = {
 };
 
 static struct platform_device *plat_devs[] __initdata = {
+	&ehci0_device,
+	&ehci1_device,
 	&i2c_device,
+	&ohci0_device,
+	&ohci1_device,
 	&rtc_device,
 };
 

114 lines not on this page · raw message

362 lines not on this page · raw message

index 29448bc..bc4e5a6 100644
@@ -130,8 +130,7 @@ int name[] = {\
  * keymaps to drivers that implement keyboards.
  */
 struct kbd_platform_data {
-	int *keymap;
-	unsigned int keymapsize;
+	const struct matrix_keymap_data *keymap;
 	bool rep;
 };
 

432 lines not on this page · raw message