Add video support to mx51evk board
PATCH v2 2/3 Add video support to mx51evk board
From: Renato Frias <[email protected]>
Adds video support to mx51evk board, this board allows different displays. This patch enables the WVGA TFT LCD panel only, on Display interface 1. Remove comments from include/configs/mx51evk.h to use it.
---
Changes for v2:
- Removed trailing whitespaces from struct fb_videomode
- Using PAD_CTL_* definitions
- Updated commit message
board/freescale/mx51evk/mx51evk.c | 60 ++++++++++++++++++++++++++++++++++++- include/configs/mx51evk.h | 11 +++++++ 2 files changed, 70 insertions(+), 1 deletions(-)
board/freescale/mx51evk/mx51evk.c +59 -1
@@ -34,9 +34,37 @@#include <fsl_pmic.h> #include <mc13892.h> +#ifdef CONFIG_LCD +#include <linux/fb.h> +#include <lcd.h> +#endif +DECLARE_GLOBAL_DATA_PTR ;static u32 system_rev; +extern int mx51_fb_init (struct fb_videomode *mode,u32 ipu_di,u32 pix_fmt); + +#ifdef CONFIG_LCD +static struct fb_videomode claa_wvga = { +"CLAA07LC0ACW" , +57 ,/* Refresh */ +800 ,/* xres */ +480 ,/* yres */ +37037 ,/* pixclock = 27Mhz */ +40 ,/* left margin */ +60 ,/* right margin */ +10 ,/* upper margin */ +10 ,/* lower margin */ +20 ,/* hsync-len */ +10 ,/* vsync-len */ +0 ,/* sync */ +FB_VMODE_NONINTERLACED ,/* vmode */ +0 ,/* flag */ +}; + +static int wvga_ipu_di =1 ; +static int wvga_bppix =16 ; +#endif #ifdef CONFIG_FSL_ESDHC struct fsl_esdhc_cfg esdhc_cfg[2] = {
@@ -148,6 +176,34 @@ static void setup_iomux_fec(void)mxc_iomux_set_pad (MX51_PIN_NANDF_D11 ,0x2180 ); } +#ifdef CONFIG_LCD +void setup_iomux_ipu (void ) +{ +/* DISP2_DAT [0:15] are configured by default */ +mxc_request_iomux (MX51_PIN_DI1_D1_CS ,IOMUX_CONFIG_ALT4 ); +mxc_iomux_set_pad (MX51_PIN_DI1_D1_CS , +PAD_CTL_PKE_ENABLE |PAD_CTL_DRV_HIGH |PAD_CTL_SRE_FAST ); +mxc_request_iomux (MUX_IN_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT , +INPUT_CTL_PATH1 ); + +/* DISP2_DRDY pin */ +mxc_request_iomux (MX51_PIN_DI_GP4 ,IOMUX_CONFIG_ALT4 ); +mxc_iomux_set_pad (MX51_PIN_DI_GP4 ,PAD_CTL_PKE_ENABLE | +PAD_CTL_PUE_KEEPER |PAD_CTL_DRV_LOW ); +} + +void lcd_enable (void ) +{ +int ret; + + ret =mx51_fb_init (&claa_wvga, wvga_ipu_di, wvga_bppix); +if (ret) { +puts ("LCD cannot be configured\n" ); + } + +} +#endif +#ifdef CONFIG_MXC_SPI static void setup_iomux_spi (void ) {
@@ -409,7 +465,9 @@ int board_init(void)setup_iomux_uart ();setup_iomux_fec (); - +#ifdef CONFIG_LCD +setup_iomux_ipu (); +#endif return 0 ; }
include/configs/mx51evk.h +11 -0
@@ -211,6 +211,17 @@#define CONFIG_SYS_DDR_CLKSEL 0#define CONFIG_SYS_CLKTL_CBCDR 0x59E35100 +/* +* Framebuffer and LCD +*/ +/* +#define CONFIG_LCD +#define CONFIG_VIDEO_MX5 +#define LCD_BPP LCD_COLOR16 +#define CONFIG_CMD_BMP +#define CONFIG_BMP_16BPP +*/ +/*----------------------------------------------------------------------- * FLASH and environment organization */
Signature · 1 line
1.6.0.4
PATCH v2 2/3 Add video support to mx51evk board
Quoted 5 lines · Renato Frias
From: Renato Frias <[email protected]>
Adds video support to mx51evk board, this board allows different displays. This patch enables the WVGA TFT LCD panel only, on Display interface 1. Remove comments from
include/configs/mx51evk.hto use it.
Last line does not apply for the commit message. This is only a change from your V1 patch, because the mx51evk.h in mainline has no commented configuration.
board/freescale/mx51evk/mx51evk.c line 66
Quoted 3 lines
board/freescale/mx51evk/mx51evk.c +3
-0+ +static int wvga_ipu_di =1 ; +static int wvga_bppix =16 ;
Why do you set these variables as you need only in lcd_enable() ?
include/configs/mx51evk.h line 217
Quoted 4 lines
include/configs/mx51evk.h +4
-0+/* +* Framebuffer and LCD +*/ +/*
You say you removed the comment, but it seems you have not....
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de =====================================================================