imx: Get fec mac address from fuse
Subsystems (3)
PATCH v5 1/1 imx: Get fec mac address from fuse
The patch is to support getting FEC MAC address from fuse bank.
---
Changes for v2:
- correct the mac address byte order according to review comments
- add memset(edev, 0. sizeof(*edev)) when do fec_probe,
- fix some code comments
Changes for v3:
- rebase
- address the comments of Stefano, make the imx_get_mac_from_fuse(), declared independently inside each imx-regs.h to make it specific for each processor, because it accesses to different structures.
- address the comments of Wolfgang and Stefano, use struct to access mac_addr fuse.
Changes for v4:
- Address the comments of Wolfgang, use fuse_regs instead of bank addres and change from fuse1_6 to fuse0_5 naming convention and use fuse_bank0_regs instead of fuse_bank0 to kill misleading.
Changes for v5:
- Fix the typo error of fuse5_31[0x11] as Wolfgang point out
- Change the print message "got MAC address from EEPROM to
"got MAC address from fuse" which comply with this commit title.
--- arch/arm/cpu/arm926ejs/mx25/generic.c | 12 ++++++++++ arch/arm/cpu/arm926ejs/mx27/generic.c | 12 ++++++++++ arch/arm/cpu/armv7/mx5/soc.c | 14 ++++++++++++ arch/arm/include/asm/arch-mx25/imx-regs.h | 19 +++++++++------ arch/arm/include/asm/arch-mx27/imx-regs.h | 18 ++++++++++----- arch/arm/include/asm/arch-mx5/imx-regs.h | 34 +++++++++++++++++++++++++++++ drivers/net/fec_mxc.c | 17 +------------ 7 files changed, 97 insertions(+), 29 deletions(-)
arch/arm/cpu/arm926ejs/mx25/generic.c +12 -0
@@ -260,4 +260,16 @@ void mx25_fec_init_pins (void) writel (outpadctl, &padctl->pad_fec_tdata1); } + +void imx_get_mac_from_fuse (unsigned char *mac) +{ +int i; +struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE ; +struct fuse_bank *bank = &iim->bank[0 ]; +struct fuse_bank0_regs *fuse = + (struct fuse_bank0_regs *)bank->fuse_regs; + +for (i =0 ; i <6 ; i++) + mac[i] =readl (&fuse->mac_addr[i]); +}#endif /* CONFIG_FEC_MXC */
arch/arm/cpu/arm926ejs/mx27/generic.c +12 -0
@@ -313,6 +313,18 @@ void mx27_fec_init_pins(void)for (i =0 ; i <ARRAY_SIZE (mode); i++) imx_gpio_mode(mode[i]); } + +void imx_get_mac_from_fuse (unsigned char *mac) +{ +int i; +struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE ; +struct fuse_bank *bank = &iim->bank[0 ]; +struct fuse_bank0_regs *fuse = + (struct fuse_bank0_regs *)bank->fuse_regs; + +for (i =0 ; i <6 ; i++) + mac[6 -1 -i] =readl (&fuse->mac_addr[i]); +}#endif /* CONFIG_FEC_MXC */ #ifdef CONFIG_MXC_MMC
arch/arm/cpu/armv7/mx5/soc.c +14 -0
@@ -100,6 +100,20 @@ int cpu_eth_init(bd_t *bis)return rc; } +#if defined(CONFIG_FEC_MXC ) +void imx_get_mac_from_fuse (unsigned char *mac) +{ +int i; +struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE ; +struct fuse_bank *bank = &iim->bank[1 ]; +struct fuse_bank1_regs *fuse = + (struct fuse_bank1_regs *)bank->fuse_regs; + +for (i =0 ; i <6 ; i++) + mac[i] =readl (&fuse->mac_addr[i]); +} +#endif +/* * Initializes on-chip MMC controllers. * to override, implement board_mmc_init()
arch/arm/include/asm/arch-mx25/imx-regs.h +11 -8
@@ -36,6 +36,7 @@#ifndef __ASSEMBLY__#ifdef CONFIG_FEC_MXC extern void mx25_fec_init_pins (void ); +extern void imx_get_mac_from_fuse (unsigned char *mac);#endif /* Clock Control Module (CCM) registers */
@@ -129,12 +130,17 @@ struct iim_regs {u32 iim_srev;u32 iim_prog_p;u32 res1[0x1f5 ]; -u32 iim_bank_area0[0x20 ]; -u32 res2[0xe0 ]; -u32 iim_bank_area1[0x20 ]; -u32 res3[0xe0 ]; - u32 iim_bank_area2[0x20]; +struct fuse_bank { +u32 fuse_regs[0x20 ]; +u32 fuse_rsvd[0xe0 ]; + } bank[3]; }; + +struct fuse_bank0_regs { +u32 fuse0_25[0x1a ]; +u32 mac_addr[6 ]; +}; +#endif /* AIPS 1 */
@@ -312,7 +318,4 @@ struct iim_regs {#define WSR_UNLOCK1 0x5555#define WSR_UNLOCK2 0xAAAA -/* FUSE bank offsets */ -#define IIM0_MAC 0x1a -#endif /* _IMX_REGS_H */
arch/arm/include/asm/arch-mx27/imx-regs.h +12 -6
@@ -34,6 +34,7 @@ extern void mx27_uart_init_pins(void);#ifdef CONFIG_FEC_MXC extern void mx27_fec_init_pins (void ); +extern void imx_get_mac_from_fuse (unsigned char *mac);#endif /* CONFIG_FEC_MXC */ #ifdef CONFIG_MXC_MMC
@@ -203,8 +204,18 @@ struct iim_regs {u32 iim_scs2;u32 iim_scs3;u32 res[0x1F0 ]; - u32 iim_bank_area0[0x100]; +struct fuse_bank { +u32 fuse_regs[0x20 ]; +u32 fuse_rsvd[0xe0 ]; + } bank[1]; }; + +struct fuse_bank0_regs { +u32 fuse0_3[4 ]; +u32 mac_addr[6 ]; +u32 fuse10_31[0x16 ]; +}; +#endif #define IMX_IO_BASE 0x10000000
@@ -512,9 +523,4 @@ struct iim_regs {#define IIM_ERR_SNSE (1 << 2)#define IIM_ERR_PARITYE (1 << 1) -/* Definitions for i.MX27 TO2 */ -#define IIM0_MAC 5 -#define IIM0_SCC_KEY 11 -#define IIM1_SUID 1 -#endif /* _IMX_REGS_H */
arch/arm/include/asm/arch-mx5/imx-regs.h +34 -0
@@ -205,9 +205,13 @@#define BOARD_REV_1_0 0x0#define BOARD_REV_2_0 0x1 +#define IMX_IIM_BASE (IIM_BASE_ADDR) +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))#include <asm/types.h> +extern void imx_get_mac_from_fuse (unsigned char *mac); +#define __REG (x) (*((volatile u32 *)(x)))#define __REG16 (x) (*((volatile u16 *)(x)))#define __REG8 (x) (*((volatile u8 *)(x)))
@@ -275,6 +279,36 @@ struct src {u32 sisr;u32 simr; }; + +struct iim_regs { +u32 stat; +u32 statm; +u32 err; +u32 emask; +u32 fctl; +u32 ua; +u32 la; +u32 sdat; +u32 prev; +u32 srev; +u32 preg_p; +u32 scs0; +u32 scs1; +u32 scs2; +u32 scs3; +u32 res0[0x1f1 ]; +struct fuse_bank { +u32 fuse_regs[0x20 ]; +u32 fuse_rsvd[0xe0 ]; + } bank[4 ]; +}; + +struct fuse_bank1_regs { +u32 fuse0_8[9 ]; +u32 mac_addr[6 ]; +u32 fuse15_31[0x11 ]; +}; +#endif /* __ASSEMBLER__*/ #endif /* __ASM_ARCH_MXC_MX51_H__ */
drivers/net/fec_mxc.c +2 -15
@@ -312,21 +312,8 @@ static void fec_rbd_clean(int last, struct fec_bd *pRbd)static int fec_get_hwaddr (struct eth_device *dev,unsigned char *mac) { -/* -* The MX27 can store the mac address in internal eeprom -* This mechanism is not supported now by MX51 or MX25 -*/ -#if defined(CONFIG_MX51 ) || defined(CONFIG_MX25 ) -return -1 ; -#else -struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE ; -int i; - -for (i =0 ; i <6 ; i++) - mac[6 -1 -i] =readl (&iim->iim_bank_area0[IIM0_MAC + i]); - +imx_get_mac_from_fuse (mac);return !is_valid_ether_addr (mac); -#endif }static int fec_set_hwaddr (struct eth_device *dev)
@@ -754,7 +741,7 @@ static int fec_probe(bd_t *bd)eth_register (edev);if (fec_get_hwaddr (edev, ethaddr) ==0 ) { -printf ("got MAC address from EEPROM: %pM\n" , ethaddr); +printf ("got MAC address from fuse: %pM\n" , ethaddr);memcpy (edev->enetaddr, ethaddr,6 ); }
Signature · 1 line
1.7.0.4
PATCH v5 1/1 imx: Get fec mac address from fuse
Quoted 3 lines · Jason Liu
The patch is to support getting FEC MAC address from fuse bank.
Signed-off-by Jason Liu <[email protected]>
Hi Jason,
Review
Quoted 2 lines
(quoted diff) +2
-0+ for (i = 0; i < 6; i++) + mac[i] = readl(&fuse->mac_addr[i]);
This works, but implicitely converts the integer to a char. Should we add a mask to make clear that only the LSB of the read value is taken ?
arch/arm/cpu/arm926ejs/mx27/generic.c void mx27_fec_init_pins(void) · line 326
Quoted 2 lines
arch/arm/cpu/arm926ejs/mx27/generic.c +2
-0+for (i =0 ; i <6 ; i++) + mac[6 -1 -i] =readl (&fuse->mac_addr[i]);
^
|--- missing spaces
Quoted 12 lines
arch/arm/include/asm/arch-mx5/imx-regs.h +12
-0+ +struct iim_regs { +u32 stat; +u32 statm; +u32 err; +u32 emask; +u32 fctl; +u32 ua; +u32 la; +u32 sdat; +u32 prev; +u32 srev;
arch/arm/include/asm/arch-mx5/imx-regs.h struct src { · line 303
Quoted 10 lines
arch/arm/include/asm/arch-mx5/imx-regs.h +10
-0+u32 preg_p; +u32 scs0; +u32 scs1; +u32 scs2; +u32 scs3; +u32 res0[0x1f1 ]; +struct fuse_bank { +u32 fuse_regs[0x20 ]; +u32 fuse_rsvd[0xe0 ]; + } bank[4 ];
I see a discrepancy between i.mx27 and i.mx51 and it is not clear to me if it is correct. Both processor has the same register map (at least as meaning) until scs3. The offset for this register is for both processors 0x3c. The fuse bank0 starts for both processor at the offset 0x804, as I see in manuals. However, you reserved in one case 0x1f0 integers and in the other case 0x1f1. Is it correct ?
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de =====================================================================
PATCH v5 1/1 imx: Get fec mac address from fuse
Hi, Stefano,
2010/11/18 Stefano Babic <[email protected]>:
Quoted 5 lines · Jason Liu
Quoted 3 lines
The patch is to support getting FEC MAC address from fuse bank.
Signed-off-by Jason Liu <[email protected]>
Quoted 7 lines
Hi Jason,
Quoted 2 lines
+ ? ? for (i = 0; i < 6; i++)
+ ? ? ? ? ? ? mac[i] =readl(&fuse->mac_addr[i]);This works, but implicitely converts the integer to a char. Should we add a mask to make clear that only the LSB of the read value is taken ?
In fact, I think it's not need to add a mask to do it. But for clearance, I can add it per your request.
mac[i] = readl(&fuse->mac_addr[i]) & 0xff;
Quoted 5 lines
Quoted 3 lines
+ ? ? for (i = 0; i < 6; i++)
+ ? ? ? ? ? ? mac[6-1-i] =readl(&fuse->mac_addr[i]);? ? ? ? ? ? ? ? ? ? ^
? ? ? ? ? ? ? ? ? ? |--- missing spaces
do you mean it need change to mac[6 - 1 - i] ?
Quoted 22 lines
Quoted 22 lines
(quoted diff) +21
-0+ +struct iim_regs { + ? ? u32 ? ? stat; + ? ? u32 ? ? statm; + ? ? u32 ? ? err; + ? ? u32 ? ? emask; + ? ? u32 ? ? fctl; + ? ? u32 ? ? ua; + ? ? u32 ? ? la; + ? ? u32 ? ? sdat; + ? ? u32 ? ? prev; + ? ? u32 ? ? srev; + ? ? u32 ? ? preg_p; + ? ? u32 ? ? scs0; + ? ? u32 ? ? scs1; + ? ? u32 ? ? scs2; + ? ? u32 ? ? scs3; + ? ? u32 ? ? res0[0x1f1]; + ? ? struct fuse_bank { + ? ? ? ? ? ? u32 ? ? fuse_regs[0x20]; + ? ? ? ? ? ? u32 ? ? fuse_rsvd[0xe0];
Quoted 8 lines
Quoted 1 line
+ ? ? } bank[4];
I see a discrepancy between i.mx27 and i.mx51 and it is not clear to me if it is correct. Both processor has the same register map (at least as meaning) until scs3. The offset for this register is for both processors
0x3c. The fuse bank0 starts for both processor at the offset0x804, as I see in manuals. However, you reserved in one case0x1f0integers and in the other case0x1f1. Is it correct ?
I think that the original mx27 code should be wrong. I will fix it. Thank you for your review.
Quoted 15 lines
Best regards,
Stefano Babic--
=====================================================================
DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 ?Email: office at denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v5 1/1 imx: Get fec mac address from fuse
Quoted 7 lines · Jason Liu
Quoted 5 lines
arch/arm/cpu/arm926ejs/mx27/generic.c void mx27_fec_init_pins(void) · line 326
Quoted 3 lines
arch/arm/cpu/arm926ejs/mx27/generic.c +2
-0+for (i =0 ; i <6 ; i++) + mac[6 -1 -i] =readl (&fuse->mac_addr[i]);^
|--- missing spacesdo you mean it need change to mac[6 - 1 - i] ?
Yes, this is a coding style issue.
Quoted 1 line
I think that the original mx27 code should be wrong.
I come with the same conclusion.
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de =====================================================================